Strong SRT 7007 User Manual

Digital HD Satellite Receiver

SRT 7007

Picture similar

User Manual

Inhaltsverzeichnis

Indice
Índice

Manual do Ulizador

Uživatelská příručka

Používateľská príručka

Instrukcja obsługi

Upute za korištenje

Felhasználói kézikönyv

Kullanıcı Kılavuzu

Руководство пользователя

Посібник користувача

Supplied by STRONG & Co, Japan

Represented by

STRONG Ges.m.b.H.

Franz-Josefs-Kai 1

1010 Vienna

Austria

Email: [e-mail]

21 Jul 2016 15:28

Your receiver is delivered with USB multimedia support. After downloading the software
for recording via USB from the website www.strong.tv, the receiver can be upgraded to
support the recording and Timeshift function via USB. This user manual describes the full
functionality including the recording function and may not be applicable if the software
for recording via USB has not yet been installed.

Licenses

ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES WITH
THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY
PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO,
WHICH LICENSE IS AVAILABLE FROM MPEG LA, LLC, 6312 S. Fiddlers Green Circle, Suite 400E,
Greenwood Village, Colorado 80111 U.S.A.
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
This product contains one or more programs protected under international and U.S. copyright
laws as unpublished works. They are confidential and proprietary to Dolby Laboratories. Their
reproduction or disclosure, in whole or in part, or the production of derivative works therefrom
without the express permission of Dolby Laboratories is prohibited. Copyright 2003-2009 by Dolby
Laboratories. All rights reserved.

21 Jul 2016 15:05

1

TABLE OF CONTENTS

1.0 INSTRUCTION 7

1.1 Safety Instructions 7

1.2 Storage 7

1.3 Equipment Set-up 8

1.4 Accessories 8

1.5 Usage of external USB devices 8

2.0 YOUR RECEIVER 9

2.1 PIN code default: 0000 9

2.2 Front and side panel 9

2.3 Rear panel 9

2.4 Remote Control 9

2.5 Installing the batteries 11

2.6 Using the remote control 11

3.0 CONNECTIONS 11

3.1 Basic connection using an HDMI cable 11

3.2 Basic connection using a Scart cable 11

3.3 Connecting multiple fixed LNBs using a DiSEqC switch 12

3.4 Connecting to Ethernet 12

3.5 Connecting to digital audio amplifier 12

3.6 Connecting a USB storage device 12

4.0 FIRST TIME INSTALLATION 12

4.1 Dish setup 13

5.0 QUICK GUIDE FOR USING YOUR RECEIVER 13

6.0 OPERATION 14

6.1 Changing channels 14

6.2 Info Banner 14

6.3 Selection of audio language 15

6.4 Teletext 15

6.5 Subtitles 15

6.6 Changing the aspect ratio 15

6.7 Changing the resolution 15

6.8 EPG (Electronic Programme Guide) 15

6.9 Favourite channels 16

7.0 MAIN MENU 16

7.1 Programme 16

7.2 Picture 18

7.3 Channel Search 19

7.4 Time and date settings 23

7.5 Option 24

7.6 System Settings 24

7.7 USB 26

8.0 TROUBLESHOOTING 29

9.0 SPECIFICATIONS 31

2

1.0 INSTRUCTION

1.1 Safety Instructions

DO NOT INSTALL YOUR RECEIVER:

DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:

Safety Precautions

If the receiver does not operate normally even after strictly following the instructions in this user
manual, it is recommended to consult your dealer.

1.2 Storage

Your receiver and its accessories are stored and delivered in a packaging designed to protect against
mechanical shocks and moisture. When unpacking it, make sure that all the parts are included and
keep the packaging away from children. When transporting the receiver from one place to another
or if you are returning it under warranty conditions, make sure to repack the receiver in its original

 In a closed or poorly ventilated cabinet; directly on top of or under any other

equipment; on a surface which might obstruct the ventilation slots.

 To direct sunlight or any other equipment that generates heat; to rain or intense

moisture; to intense vibration and to any shock which may cause permanent damage
to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.

 Do not use a damaged power cord. It may cause a fire or an electric shock. Do not

touch a power cord with wet hands. It may cause an electric shock.

 When the receiver is not used for a long period of time, you should unplug the power

cord from the wall socket.

 Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you

may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap
solution, and only after disconnecting from the mains voltage supply. Make sure no
foreign objects fall through the ventilation slots because this could cause fire or an
electric shock.

 Do not place any objects on top of the receiver because this might prevent proper

cooling of the components inside.

 Never try to open the receiver. It is dangerous to touch the inside of the receiver

due to high voltages and possible electrical hazards. Opening the receiver will void
the warranty of the product. Refer all maintenance or servicing to suitably qualified
personnel.

 When you are connecting cables, be sure that the receiver is disconnected from the

mains supply voltage. Wait a few seconds after switching off the receiver before you
move the receiver or disconnect any equipment.

 It is a necessity that you only use an approved extension and compatible wiring that

is suitable for the electrical power consumption of the installed equipment. Please
ensure that the electrical power supply corresponds with the voltage on the electrical
identification plate at the back of the receiver.

3

packaging with its accessories. Failing to comply with such packaging procedures could damage the
product and void your warranty.

1.3 Equipment Set-up

We recommend you consult a professional installer to set up your equipment. Otherwise, please
follow the instructions below:

This manual provides complete instructions for installing and using this receiver. The symbols serve
as follows.

WARNING Indicates warning information.
NOTE Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver. (Bold characters)

Move to Represents a menu item within a window. (Italic characters)

1.4 Accessories

 Refer to the user manual of your TV and your antenna.
 Make sure that the SCART/HDMI cable and outdoor components are in a good

condition and the SCART/HDMI connections are well shielded and from good quality.

 1x installation instructions
 1x remote control
 2x batteries (AAA type)

NOTE: The batteries should not be recharged, disassembled, electrically short-

circuited or be mixed or used with other types of batteries. If rechargeable
accumulators instead of batteries are going to be used, we recommend
using (e.g. NiMH) types with low self-discharge to ensure long time
operation of remote control.

1.5 Usage of external USB devices

 It is recommended to use USB 2.0 storage devices. If your device is not compatible to

USB 2.0 specifications, multimedia, recording and Timeshift functions of the receiver
might not work properly.*

 If you are going to use an external USB HDD (Hard Disk Drive), please consider that the

power specifications may exceed the supported output of your receiver (5 V/800 mA).
If so, please connect your USB HDD to an according external power adapter.

 STRONG cannot guarantee compatibility with all types of USB storage devices.
 It is advised not to store important information on USB storage devices used with

the receiver. Always make backups of data on your USB storage device before using
it with this receiver. STRONG will not take responsibility for any loss of information or
circumstances caused by loss of information.

 STRONG cannot guarantee the playback of all files although extensions are listed, as it

depends on file size, codec, bit rate and resolution.

 Please ensure that either the USB device is already formatted to FAT/FAT32, or format

the USB device via your receiver, refer to chapter 7.7 USB for details.

4

*This user manual describes the full functionality including the recording function and may not be applicable if the software for recording via USB has
not yet been installed.

2.0 YOUR RECEIVER

2.1 PIN code default: 0000

2.2 Front and side panel

1. Remote control sensor:
Receives the signal from the remote control

2. LED display: Shows channel number in operation and time in Standby

3. Standby indicator: Shows power state of the receiver: Red LED - receiver is in

4. Power button: Switch the receiver to Standby or On.

5. CH-/CH+: To change channels without using the remote control

6. VOL-/VOL+ Decrease/Increase audio volume. VOL-/VOL+ and CH+/CH-

standby mode

double as navigation buttons when

2.3 Rear panel

1. SAT IN To connect to the LNB of your satellite dish for reception of

2. Ethernet To connect to a network switch, router or modem

3. USB For connection of USB device for Multimedia use

4. HDMI To connect to the HDMI input of your TV using a good quality

5. TV SCART To connect to TV using a SCART cable

6. Audio L/R To connect to an analogue amplifier for stereo audio

7. S/PDIF coaxial To connect to a digital or home cinema audio amplifier

8. Power connector The receiver requires a wall adapter, mains voltage input

satellite broadcast signal

HDMI cable

100~240V AC 50~60Hz 12V, 1.5A DC output. Please check the
local power conditions before connecting the receiver to the
mains supply.

2.4 Remote Control

1. q Turns the receiver ON/Standby

2. ! To turn the sound on or off

3. 0-9 Channel number and numeric value input

4. TV/R Toggles between TV and radio mode

5.  No function

6. FAV To access your favourite channels. Toggles between available

7. 9 To switch between the last viewed channels

favourite groups

Fig. 1

Fig. 2

Fig. 3

5

8. AUDIO Displays the audio selection menu with selections for available

9. INFO Press once to display channel number/name and current/coming

10. EPG Viewing mode: Displays the EPG (Electronic Programme Guide)

11. p/q Switches to the next/previous channel in viewing mode, switches

12. OK Viewing mode: Displays the channel list. Menu: activation of the

13. tu Decreasing/increasing the volume level in viewing mode/

14. MENU To open the main menu in viewing mode or to go one step back

15.  Cancellation of current process/exit from main menu to viewing

16. VOL+/ Increases/decreases the volume level in TV mode

17. P+/P Jumps 10 places up or down in channel list or any other list.

18. LIST Displays the channel list.

19. CH+/ Channel up/down

20. OPT No function.

21. TEXT To open Teletext if available on the current channel.

22. SUB To select subtitles language out of available ones on the current

23.  No function

24. 2 Hold play during playback/starting Timeshift mode*

25. 5 Searches backwards during playback/Timeshift*. Each pressing

26. 6 Searches forwards during playback/Timeshift*. Each pressing

27. 4 Starts recording of the currently watched programme*. Toggles

28. u Starts/resumes the playback/Timeshift*. Shortcut to recordings

29. 7 Jumps to the previous file during playback.

30. 8 Jumps to the next file during playback.

31. 3 Stops playback of multimedia files and Timeshift*.

32. RED Flexible functions in OSD menu and Teletext.

33. GREEN Flexible functions in OSD menu and Teletext. Changes the picture

34. YELLOW Flexible functions in OSD menu and Teletext. Changes the picture

35. BLUE In viewing mode: displays the schedule menu for easy setup

6

languages and audio modes

information. Press twice to display detailed event information.
Press again to get back to viewing mode

to the next/previous page in channel list or moving the highlight
up/down in the menu

highlighted item

navigating through the menus/changing values of settings in a
menu

in the menu

mode

channel

increases the speed (x2 – x32)

increases the speed (x2 – x32)

between lists in menu.

list in viewing mode.

resolution in viewing mode.

Aspect Ratio in viewing mode.

timers; Flexible functions in OSD menu and Teletext.