Steinberg UR22mkII Users Manual

EN

DE

FR

ES

PT

IT

RU

JA

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE:
DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result
in harmful interference with other electronic
devices. This equipment generates/uses radio
frequencies and, if not installed and used according
to the instructions found in the users manual, may
cause interference harmful to the operation of other
electronic devices. Compliance with FCC

* This applies only to products distributed by Yamaha Corporation of America. (class B)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Type of Equipment : USB Audio Interface

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired

See user manual instructions if interference to radio reception is suspected.

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : [phone]

Model Name : UR22mkII

operation.

regulations does not guarantee that interference
will not occur in all installations. If this product is
found to be the source of interference, which can
be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of
the following measures:

Relocate either this product or the device that is
being affected by the interference.

Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.

In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to co-axial
type cable.

If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you
can not locate the appropriate retailer, please con­tact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620

The above statements apply ONLY to those
products distributed by Yamaha Corporation of
America or its subsidiaries.

* This applies only to products distributed by Yamaha Corporation of America.

(FCC DoC)

Contents

PRECAUTIONS.........................................4

NOTICE......................................................................... 6

Information ....................................................................6

Package Contents....................................8

Disk Contents ................................................................8

Manuals.....................................................9

Conventions in this manual ...........................................9

Panel Controls and Terminals ..............10

Front Panel.................................................................. 10

Rear Panel ..................................................................11

Power supply..........................................12

Setting Up ...............................................13

1. Installing Yamaha Steinberg USB Driver ................13

2. Downloading Cubase AI.......................................... 14

Appendix.................................................15

Uninstalling Yamaha Steinberg USB Driver ................15

Technical Specifications.............................................. 16

General Specifications ................................................17

English

For detailed instructions and information on the
functions of the product, read the Operation Manual
included in the TOOLS for UR22mkII CD-ROM.

UR22mkII Getting Started 3

PRECAUTIONS

PA-en-6 1/2

PRECAUTIONS

PLEASE READ CAREFULLY
BEFORE PROCEEDING

Please keep this manual in a safe place for
future reference.

WARNING

Always follow the basic precautions
listed below to avoid the possibility of
serious injury or even death from
electrical shock, short-circuiting,
damages, fire or other hazards. These
precautions include, but are not limited
to, the following:

Do not open

• This device contains no user-serviceable parts.
Do not open the device or attempt to
disassemble the internal parts or modify them in
any way. If it should appear to be malfunctioning,
discontinue use immediately and have it
inspected by qualified Yamaha service
personnel.

Water warning

• Do not expose the device to rain, use it near
water or in damp or wet conditions, or place on it
any containers (such as vases, bottles or
glasses) containing liquids which might spill into
any openings. If any liquid such as water seeps
into the device, turn off the power of the amplifier
immediately and unplug the USB cable from the
computer. Then have the device inspected by
qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet
hands.

Hearing loss

• Do not use headphones for a long period of time
at a high or uncomfortable volume level, since
this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the
ears, consult a physician.

• When turning on the AC power in your audio
system, always turn on the power amplifier LAST,
to avoid hearing loss and speaker damage.
When turning the power off, the power amplifier
should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open flames
near the device, since they may cause a fire.

If you notice any abnormality

• If any of the following problems occur,
immediately unplug the USB cable from the
computer.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of

the device.

- Cracks or other visible damage appear on the

device.

Then have the device inspected or repaired by
qualified Yamaha service personnel.

• If this device should be dropped or damaged,
immediately turn off the power switch, disconnect
the electric plug from the outlet, and have the
device inspected by qualified Yamaha service
personnel.

4 UR22mkII Getting Started

PA-en-6 2/2

CAUTION

Always follow the basic precautions
listed below to avoid the possibility of
physical injury to you or others, or
damage to the device or other property.
These precautions include, but are not
limited to, the following:

Location

• Do not place the device in an unstable position
where it might accidentally fall over and cause
injuries.

• Do not place the device in a location where it
may come into contact with corrosive gases or
salt air. Doing so may result in malfunction.

• Before moving the device, remove all connected
cables.

Connections

• Before connecting the device to other devices,
unplug the USB cable from the computer. Also,
before turning the power of all devices on or off,
make sure that all volume levels are set to the
minimum. Failing to do so may result in electric
shock, hearing loss, or equipment damage.

PRECAUTIONS

Maintenance

• Remove the USB cable from a computer when
cleaning the device.

Handling caution

• Do not rest your weight on the device or place
heavy objects on it, and avoid use excessive
force on the buttons, switches or connectors to
prevent injuries.

Yamaha cannot be held responsible for damage
caused by improper use or modifications to the
device, or data that is lost or destroyed.

UR22mkII Getting Started 5

PRECAUTIONS

NOTICE

To avoid the possibility of malfunction/
damage to the product, damage to data, or
damage to other property, follow the notices
below.

■ Handling and maintenance

• Do not use the device in the vicinity of a TV,
radio, home audio/video equipment , mobile
phone, or other electric devices. Otherwise, the
device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or
vibration, or extreme cold or heat (such as in
direct sunlight, near a heater, or in a car during
the day), in order to prevent the possibility of
panel disfiguration, unstable operation, or
damage to the internal components.

• Do not place vinyl, plastic or rubber objects on
the device, since this might discolor the panel.

• When cleaning the device, use a dry and soft
cloth. Do not use paint thinners, solvents,
cleaning fluids, or chemical-impregnated wiping
cloths.

• Condensation can occur in the device due to
rapid, drastic changes in ambient temperature—
when the device is moved from one location to
another, or air conditioning is turned on or off, for
example. Using the device while condensation is
present can cause damage. If there is reason to
believe that condensation might have occurred,
leave the device for several hours without turning
on the power until the condensation has
completely dried out.

• This disk containing the software is not meant for
use with an audio/visual system (CD player, DVD
player, etc.). Do not attempt to use the disk on
equipment other than a computer.

• Always unplug the USB cable from a computer or
turn off the computer when the device is not in
use.

■ Connectors

• XLR-type connectors are wired as follows
(IEC60268 standard): pin 1: ground, pin 2: hot
(+), and pin 3: cold (-).

Information

■ About copyrights

• The software included in the TOOLS for
UR22mkII CD-ROM and the copyrights thereof
are under exclusive ownership by Yamaha
Corporation.

• This manual is the exclusive copyrights of
Yamaha Corporation.

• Copying of the software or reproduction of this
manual in whole or in part by any means is
expressly forbidden without the written consent of
the manufacturer.

• This product incorporates and bundles computer
programs and contents in which Steinberg Media
Technologies GmbH and Yamaha Corporation
own copyrights or with respect to which it has
license to use others' copyrights. Such
copyrighted materials include, without limitation,
all computer software, style files, MIDI files,
WAVE data, musical scores and sound
recordings. Any unauthorized use of such
programs and contents outside of personal use is
not permitted under relevant laws. Any violation
of copyright has legal consequences. DON'T
MAKE, DISTRIBUTE OR USE ILLEGAL
COPIES.

■ About this manual

• The illustrations and LCD screens as shown in
this manual are for instructional purposes only.

• Steinberg Media Technologies GmbH and
Yamaha Corporation make no representations or
warranties with regard to the use of the software
and documentation and cannot be held
responsible for the results of the use of this
manual and the software.

• Windows is a registered trademark of Microsoft®
Corporation in the United States and other
countries.

• Apple, Mac, iOS and iPad are trademarks of
Apple Inc., registered in the U.S. and other
countries.

• Steinberg and Cubase are registered trademarks
of Steinberg Media Technologies GmbH.

• The company names and product names in this
manual are the trademarks or registered
trademarks of their respective companies.

• Software may be revised and updated without
prior notice.

6 UR22mkII Getting Started

PRECAUTIONS

The model number, serial number, power requirements, etc.,
may be found on or near the name plate, which is at the bottom
of the unit. You should note this serial number in the space
provided below and retain this manual as a permanent record of
your purchase to aid identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

This symbol on the products, packaging, and/or accompanying documents
means that used electrical and electronic products should not be mixed with
general household waste. For proper treatment, recovery and recycling of
old products, please take them to applicable collection points, in
accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and
the environment which could otherwise arise from inappropriate waste
handling.

For more information about collection and recycling of old products, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.

(weee_battery_eu_en_01)

Information for Users on Collection and Disposal of Old Equipment

UR22mkII Getting Started 7

Package Contents

Package Contents

The package of this product contains the
following items. After opening the package,
make sure that it includes everything listed
below.

• UR22mkII Main unit

• TOOLS for UR22mkII CD-ROM

• Getting Started (this book)

• CUBASE AI DOWNLOAD
INFORMATION (printed)

•USB cable

Disk Contents

The TOOLS for UR22mkII CD-ROM
contains the following.

Yamaha Steinberg USB Driver

This software allows communication
between the device and a computer. Make
sure to install it before initially using the
device.

Operation Manual (PDF)

The files are in the folder [Documentation],
and are separated by language. Drag and
drop the file onto the desktop.

File name

UR22mkII_OperationManual_en

NOTE

To view PDF files, you need to install Adobe
Reader on your computer. You can download
the latest version at the following website.

http://www.adobe.com/

8 UR22mkII Getting Started

Manuals

Manuals

Getting Started (this book)

Read this manual when setting up the
device. After finishing the setup as
indicated in this manual, read the Operation
Manual.

Operation Manual

This is included in the TOOLS for UR22mkII
CD-ROM. Read through this manual to
understand how to use the features of the
product.

Conventions in this manual

Windows or Mac

When the procedures or explanations are
specific to only one of the platforms,
Windows or Mac, this is properly indicated
in the manual. When the platforms do not
appear, procedures or explanations are for
both Windows and Mac.

Procedures

An arrow “” is shown for some procedures
in the manual. For example, the string
[Devices]  [Device Setup]  [Control
Panel] indicates that you should perform
the procedures in the following order.

Screens

This manual predominantly uses
screenshots of Windows. However, Mac
screenshots are used when instructions of
the function apply only to the Mac. Also, this
manual uses screenshots of Cubase Pro 8.
If you are using another version of Cubase,
the actual screenshots might not be the
same. For details, refer to the Cubase
manuals (PDF) opened from the [Help]
menu.

Version information

The letters “x.x.x” and “x.xx” indicate the
version number.

1. Click the [Devices] menu.

2. Select the [Devices Setup] option.

3. Click the [Control Panel] button.

Cubase

The phrase “Cubase” in this manual applies
to all Cubase programs and versions
(except Cubase LE). If a specific version is
indicated, the version is described in the
text.

UR22mkII Getting Started 9

Panel Controls and Terminals

Panel Controls and Terminals

Front Panel

1 [INPUT 1 GAIN] knob

2 [MIC/LINE 1/2] jacks

3 [PEAK] indicator

4 [+48V] indicator

5 [USB] indicator

6 [INPUT 2 GAIN] knob

7 [INPUT 2 HI-Z] switch

8 [MIX] knob

9 [PHONES] knob

) [PHONES ] jack

! [OUTPUT] knob

10 UR22mkII Getting Started

Rear Panel

1 [5V DC] port

2 [POWER SOURCE] switch

3 [USB2.0] terminal

4 [MIDI OUT] jack

5 [MIDI IN] jack

6 [+48V] switch

Panel Controls and Terminals

7 [LINE OUTPUT 2/R 1/L] jacks

UR22mkII Getting Started 11

Power supply

Power supply

The UR22mkII is a bus-powered type
device which can be powered by the host
computer connected via a USB cable. The
power automatically turns on when the
device is connected to the computer via a
USB cable and turns off when the device is
disconnected from the computer.

WARNING

When turning on the AC power in your audio
system, always turn on the power amplifier
LAST. When turning the power off, the
power amplifier should be turned off FIRST.

HINT

Connecting to an iPad

The power also can be supplied via a USB
power adapter or USB mobile battery from
the [5V DC] port at the rear panel. The [5V
DC] port is used only for power supply. The
[USB 2.0] terminal is also used for
transferring digital audio data.

12 UR22mkII Getting Started

Setting Up

Setting Up

The following two setup procedures are
required before you can use the device with
a computer.

1. Installing Yamaha Steinberg USB

Driver

2. Downloading Cubase AI

NOTE

Installing the Yamaha Steinberg USB Driver is
not necessary when connecting the device to
an iPad.

1. Installing Yamaha

Steinberg USB Driver

Follow the steps below to install the Yamaha
Steinberg USB Driver.

NOTE

• You are only permitted to use this software
pursuant to the terms and conditions of the
“License Agreement” shown during the
installation.

• Future upgrades of application and system
software and any changes in specifications
and functions will be announced at the
following website.
http://www.steinberg.net/

Windows

1. Disconnect all USB devices other

than the mouse and keyboard
from the computer.

2. Start the computer and log on to

the Administrator account.

Exit any open applications and close
all open windows.

3. Insert the TOOLS for UR22mkII

CD-ROM into the CD-ROM drive.

4. Open the CD-ROM then double-

click [setup.exe].

5. Follow the on-screen instructions

to install the software.

6. When installation has been

completed, click [Finish].

If a window requiring you to restart your
computer appears, follow the onscreen
instructions and restart the computer.

7. Connect the device directly to the

computer by using the included
USB cable.

Make sure not to connect it to a USB
hub.

8. Confirm that the [USB] indicator of

the device is lit.

NOTE

If the computer or iPad does not
recognize the device, the [USB] indicator
flashes continuously.

Installation of the Yamaha Steinberg USB
Driver is now complete.

Mac

1. Disconnect all USB devices other

than the mouse and keyboard
from the computer.

2. Start the computer and log in to

the Administrator account.

Exit any open applications and close
all open windows.

3. Insert the TOOLS for UR22mkII

CD-ROM into the CD-ROM drive.

4. Open the CD-ROM then double-

click [Yamaha Steinberg USB
Driver V***.pkg].

*** represents the version number.

5. Follow the on-screen instructions

to install the software.

UR22mkII Getting Started 13

Setting Up

6. When installation has been

completed, click [Restart] to
restart the computer.

7. Connect the device directly to the

computer by using the included
USB cable.

Make sure not to connect it to a USB
hub.

8. Confirm that the [USB] indicator of

the device is lit.

NOTE

If the computer or iPad does not
recognize the device, the [USB] indicator
flashes continuously.

Installation of the Yamaha Steinberg USB
Driver is now complete.

2. Downloading Cubase AI

We are offering Cubase AI as a free
download via our website, specifically for
customers who have purchased the
UR22mkII. In order to download the
software, you’ll need to first create a
MySteinberg account in the Steinberg
website. For the latest information, see the
Steinberg website below.
http://www.steinberg.net/getcubaseai/

NOTE

A valid “Download access code” is required
for Cubase AI download. It is printed on the
included CUBASE AI DOWNLOAD
INFORMATION.

The setup is now complete.

After setup is complete

For detailed instructions and information
on the functions of the product, read the
Operation Manual included in the TOOLS
for UR22mkII CD-ROM.

14 UR22mkII Getting Started

Appendix

Appendix

Uninstalling Yamaha Steinberg USB Driver

Windows

1. Disconnect all USB devices other

than the mouse and keyboard
from the computer.

2. Start the computer and log on to

the Administrator account.

Exit any open applications and close
all open windows.

3. Open the window for the uninstall

operation as follows.

Select [Control Panel]  [Uninstall a
Program] to call up the [Uninstall or
change a program] panel.

4. Select [Yamaha Steinberg USB

Driver] from the list.

5. Click the [Uninstall] / [Uninstall /

Change].

If the [User Account Control] window
appears, click [Continue] or [Yes].

6. Follow the on-screen instructions

to remove the software.

Mac

1. Disconnect all USB devices other

than the mouse and keyboard
from the computer.

2. Start the computer and log in to

the Administrator account.

Exit any open applications and close
all open windows.

3. Insert the TOOLS for UR22mkII

CD-ROM into the CD-ROM drive.

4. Open the CD-ROM then double-

click [Uninstall Yamaha Steinberg
USB Driver].

5. Click [Run] when the “Welcome to

the Yamaha Steinberg USB Driver
uninstaller.” message appears.

After that, follow the on-screen
instructions to uninstall the software.

6. Click [Restart] when the

“Uninstallation completed.”
message appears.

7. When the message prompting you

to restart your computer appears,
click [Restart].

Uninstalling Yamaha Steinberg USB Driver
is now complete.

Uninstalling Yamaha Steinberg USB Driver
is now complete.

UR22mkII Getting Started 15

Technical Specifications

Technical Specifications

MIC INPUT 1/2 (Balanced)

Frequency Response +0.1/-0.3 dB, 20 Hz – 22 kHz

Dynamic Range 101 dB, A-Weighted

THD+N 0.0035 %, 1 kHz, -1 dBFS, 22 Hz/22 kHz BPF

Maximum Input Level +4 dBu

Input Impedance 4 kΩ

Gain Range +6 dB – +60 dB

LINE INPUT 1/2 (Balanced)

Maximum Input Level +24 dBu

Input Impedance 20 kΩ

Gain Range -14 dB – +40 dB

HI-Z INPUT 2 (Unbalanced)

Maximum Input Level +8.5 dBV

Input Impedance 1 MΩ

Gain Range -0.7 dB – +53.3 dB

LINE OUTPUT 1/L 2/R (Impedance balanced)

Frequency Response +0.1/-0.3 dB, 20 Hz – 22 kHz

Dynamic Range 104 dB, A-Weighted

THD+N 0.005 %, 1 kHz, -1 dBFS, 22 Hz/22 kHz BPF

Maximum Output Level +10 dBu

Output Impedance 150 Ω

PHONES

Maximum Output Level 6 mW+6 mW, 40 Ω

USB

Specification USB2.0, 24 bit, 44.1 kHz/48 kHz/88.2 kHz/96 kHz/176.4 kHz/192 kHz

XLR INPUT

Polarity 1: Ground

2: Hot (+)
3: Cold (-)

16 UR22mkII Getting Started

General Specifications

General Specifications

Power Requirements 2.5 W

Dimensions 159 (W) × 46 (H) × 159 (D) mm

Net weight 1030 g

Operating Free-air
Temperature Range

Included Accessories ・ TOOLS for UR22mkII CD-ROM

The contents of this manual apply to the latest specifications as of the printing date. Since
Steinberg/Yamaha makes continuous improvements to the product, this manual may not apply
to the specifications of your particular product. To obtain the latest manual, access the
Steinberg website then download the manual file. Since specifications, equipment or
separately sold accessories may not be the same in every locale, please check with your
Steinberg/Yamaha dealer.

0 – 40 ℃

・ Getting Started (brochure)
・ CUBASE AI DOWNLOAD INFORMATION (printed)
・ USB Cable

UR22mkII Getting Started 17

Steinberg Website
http://www.steinberg.net/

Manual Development Department

© 2015 Yamaha Corporation

Published 09/2015 MWHD-A0

Printed in China

ZR29220