The STG3684A is a high-speed CMOS dual analog SPDT (single-pole dual-throw) switch or
dual 2:1 multiplexer/demultiplexer bus switch fabricated using silicon gate C
technology. Designed to operate from 1.65 to 4.3 V, this device is ideal for portable
applications.
It offers very low ON resistance (R
control the independent channel switches nS1 and nS2. The switches nS1 are ON
(connected to common ports Dn) when the nIN input is held high and OFF (state of high
impedance exists between the two ports) when nIN is held low. The switches nS2 are ON
(connected to common ports Dn) when the nIN input is held low and OFF (state of high
impedance exists between the two ports) when IN is held high. Additional key features are
fast switching speed, break-before-make delay time and ultra low power consumption. All
inputs and outputs are equipped with protection circuits against static discharge, giving
them ESD and excess transient voltage immunity.
<0.5Ω) at VCC= 3.6 V. The nIN inputs are provided to
ON
2
MOS
Doc ID 11481 Rev 75/29
Pin settingsSTG3684A
2 Pin settings
2.1 Pin connection
Figure 1.Pin connection (top through view)
D1
1IN
9
1S2
1S1
1
2
10
8
GND
7
2S1
V
1S2
CC
1IN
1S1
D1
V
CC
3
QFN10L (1.8 x 1.4 mm)
1
2
3
4
5
DFN10L (2.3 x 2 mm)
4
2IN
5
D2
6
2S2
10
2S2
9
D2
8
2S1
7
2IN
6
GND
6/29Doc ID 11481 Rev 7
STG3684APin settings
2.2 Pin description
Table 2.Pin description
Pin number
SymbolName and function
QFN10LDFN10L
151S2Independent channel
231S1Independent channel
31V
CC
Positive voltage supply
472INControl
59D2Common channel
6102S2Independent channel
782S1Independent channel
86GNDGround (0 V)
921INControl
104D1Common channel
Note:Exposed pad must be soldered to a floating plane. Do NOT connect to power or ground.
Doc ID 11481 Rev 77/29
Input equivalent circuit and truth tableSTG3684A
3 Input equivalent circuit and truth table
Figure 2.Input equivalent circuit
Table 3.Truth table
INSwitch S1Switch S2
HONOFF
LOFF
(1)
(1)
ON
1. High impedance.
8/29Doc ID 11481 Rev 7
STG3684AMaximum rating
4 Maximum rating
Stressing the device above the rating listed in the “Absolute maximum ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 4.Absolute maximum ratings
SymbolParameterValueUnit
I
CC
I
T
V
V
V
I
I
I
GND
P
Supply voltage-0.5 to 5.5V
CC
V
DC input voltage-0.5 to VCC + 0.5V
I
DC control input voltage-0.5 to 5.5V
IC
DC output voltage-0.5 to VCC + 0.5V
O
DC input diode current on control pin (VIN<0V)-50mA
IKC
I
DC Input diode current (VIN<0V)±50mA
IK
DC output diode current±20mA
OK
I
DC output current±300mA
O
DC output current peak (pulse at 1 ms, 10% duty cycle)±500mA
OP
or
DC VCC or ground current±100mA
Power dissipation at TA= 70 °C 1120mW
D
Storage temperature-65 to 150°C
STG
T
Lead temperature (10 sec)300°C
L
Recommended operating conditions
Table 5.Recommended operating conditions
SymbolParameterValueUnit
V
V
V
T
dt/dv
Supply voltage1.65 to 4.3V
CC
V
Input voltage0 to V
I
Control input voltage0 to 4.3V
IC
Output voltage0 to V
O
Operating temperature-40 to 85°C
op
V
= 1.65 to 2.7 V0 to 20
Input rise and fall time control
input
CC
V
= 3.0 to 4.3 V0 to 10
CC
CC
CC
V
V
ns/V
Doc ID 11481 Rev 79/29
Electrical characteristicsSTG3684A
5 Electrical characteristics
Table 6.DC specifications
SymbolParameterVCC (V)Test condition
1.65 −1.950.65 V
2.3 −2.51.21.2
V
High level input voltage
IH
2.7 −3.01.31.3
3.0 −3.61.41.4
4.31.51.5
1.65 −1.950.250.25
2.3 −2.50.250.25
V
Low level input voltage
IL
2.7 −3.00.250.25
3.0 −3.60.300.30
4.30.400.40
4.3
3.60.450.500.60
= 0 V to V
V
R
Switch ON resistance
ON
3.00.500.550.60
S
IS= 100 mA
2.30.600.700.80
CC
Value
MinTypMaxMinMax
CC
0.65 V
CC
0.45 0.500.60
UnitTA= 25 °C-40 to 85 °C
V
V
Ω
ΔR
R
I
ON resistance match
ON
between channels
ON resistance
FLAT
flatness
OFF state leakage
OFF
current (nSn), (Dn)
I
Input leakage current 0 −4.3V
IN
Quiescent supply
I
CC
current
(3)
(1)
(1),(2)
1.80.800.91.0
=1.5V
V
2.7
4.3
S
I
= 100 mA
S
0.1Ω
0.15 0.200.20
3.60.150.200.20
3.00.150.200.20
2.70.150.200.20
V
=1.5V
S
I
= 100 mA
S
2.30.200.250.25
1.650.35 0.450.45
4.3V
1.65 −4.3 V
= 0.3 or 4 V±20±100 nA
S
= 0 to 4.3 V±0.05±1μA
IN
= VCC or GND±0.05±0.2μA
IN
Ω
10/29Doc ID 11481 Rev 7
STG3684AElectrical characteristics
Table 6.DC specifications (continued)
Value
SymbolParameterVCC (V)Test condition
MinTypMaxMinMax
V
1IN, V2IN
1.65 V
I
CCLV
Quiescent supply
current low voltage
driving
4.3
V
1IN, V2IN
1.80 V
V
1IN, V2IN
2.60 V
1. Guaranteed by design.
2. ΔR
ON=RON(max)-RON(min)
3. Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal ranges.
1. Off Isolation = 20 Log10 (VD/VS), VD = output. VS = input at off switch.
Control pin input
IN
capacitance
Sn port capacitance3.3f = 1 MHz40
Sn
D port capacitance
D
when switch is enabled
3.3f = 1 MHz114
=50Ω55MHz
L
5
pFC
12/29Doc ID 11481 Rev 7
STG3684ATest circuit
6 Test circuit
Figure 3.ON resistance
I
DS
V
V
CC
S1
VS
S2
GND
IN
GND
D
CS14071
Doc ID 11481 Rev 713/29
Test circuitSTG3684A
Figure 4.OFF leakage
9
&&
,
62))
$
9
66
9
&&
Figure 5.OFF isolation
,
'2))
'
$
9
'
6
,1
*1'
&6
9
&&
6
9
287
6
,1
*1'
9
6
*1'
14/29Doc ID 11481 Rev 7
#3
STG3684ATest circuit
Figure 6.Bandwidth
V
CC
S1
S2
V
V
S
IN
CC
Figure 7.Channel-to-channel crosstalk
GND
50 Ω
V
OUT
CS00371
#36
Doc ID 11481 Rev 715/29
Test circuitSTG3684A
Figure 8.Test circuit
1. CL= 5/35 pF or equivalent (includes jig and probe capacitance).
R
=50Ω or equivalent.
L
RT=Z
Figure 9.Break-before-make time delay
of pulse generator (typically 50 Ω).
OUT
#36
#36
16/29Doc ID 11481 Rev 7
STG3684ATest circuit
Figure 10. Charge injection (V
GEN
=0V, R
=0Ω, RL=1MΩ, CL= 100 pF)
GEN
Doc ID 11481 Rev 717/29
Test circuitSTG3684A
Figure 11. Turn-on, turn-off delay time
18/29Doc ID 11481 Rev 7
STG3684APackage mechanical data
7 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK®
®
is an ST trademark.
Figure 12. QFN10L (1.8 x 1.4 mm) package outline
1. Drawing not to scale.
Doc ID 11481 Rev 719/29
Package mechanical dataSTG3684A
Table 9.QFN10L (1.8 x 1.4 mm) mechanical data
millimetersinches
Symbol
Nom Min Max Nom Min Max
A 0.50 0.45 0.55 0.0200.0170.021
A1 0.02 0 0.05 0.001 00.002
A3 0.127 0.00500
b 0.20 0.15 0.25 0.0070.0060.010
D 1.80 1.70 1.90 0.0700.0660.074
E 1.40 1.30 1.50 0.0550.0510.059
e 0.40 0.015
L 0.40 0.30 0.50 0.0150.0110.020
Figure 13. QFN10L (1.8 x 1.4 mm) footprint recommendations
1. Drawing not to scale.
20/29Doc ID 11481 Rev 7
STG3684APackage mechanical data
Figure 14. QFN10L (1.8 x 1.4 mm) carrier type
1. Drawing not to scale.
!-
Doc ID 11481 Rev 721/29
Package mechanical dataSTG3684A
Figure 15. QFN10L (1.8 x 1.4 mm) reel information - back view
1. Drawing not to scale.
22/29Doc ID 11481 Rev 7
!-
STG3684APackage mechanical data
Figure 16. QFN10L (1.8 x 1.4 mm) reel information - front side
1. Drawing not to scale.
!-
Doc ID 11481 Rev 723/29
Package mechanical dataSTG3684A
Figure 17.DFN10L (2 x 2.3 mm) package outline
!
1. Drawing not to scale.
Table 10.DFN10L (2 x 2.3 mm) mechanical data
millimeters mils
Symbol
MinTyp Max MinTyp Max
A 0.50 0.55 0.60 19.7 21.7 23.6
A1 0.02 0.05 0.8 2.0
b 0.15 0.20 0.25 5.9 7.9 9.8
D 2.20 2.30 2.40 86.6 90.6 94.5
D2 1.65 1.70 1.75 65.0 66.9 68.9
E 1.90 2 2.10 74.8 78.7 82.7
E2 0.15 0.20 0.25 5.9 7.9 9.8
e 0.40 15.7
L 0.35 0.40 0.45 13.8 15.7 17.7
K 0.20 7.9
24/29Doc ID 11481 Rev 7
STG3684APackage mechanical data
Figure 18.DFN10L (2 x 2.3 mm) carrier type
+
"
!
"
+
1. Drawing not to scale.
!
#/6%2
$&.,
Doc ID 11481 Rev 725/29
Package mechanical dataSTG3684A
Figure 19. DFN10L (2 x 2.3 mm) reel information - back view
1. Drawing not to scale.
26/29Doc ID 11481 Rev 7
!-
STG3684APackage mechanical data
Figure 20. DFN10L (2 x 2.3 mm) reel information - front side
1. Drawing not to scale.
!-
Doc ID 11481 Rev 727/29
Revision historySTG3684A
8 Revision history
Table 11.Document revision history
DateRevisionChanges
04-Jul-20051First release.
22-Aug-20052The V
15-May-20063New template, few updates.
21-Jun-20064Mechanical data updated.
Removed STG3684QTR order code, small text changes, updated
10-Sept-20075
15-Nov-20076
04-Feb-20117
Figure 3 on page 13, Figure 4 on page 14, Figure 5 on page 14,
Figure 6 on page 15, layout restructured.
Added list of tables and list of figures, updated Features Section on
Ta b le 6 , ECOPACK text, corrected typo in Tab le 2 to Ta bl e 8 ,
Figure 7, Figure 9.
and VIC values has been changed on Table 4 on page 9.
CC
value in Table 5 on page 9, removed the -55 to -
op
° C values in Table 6 on page 10 and Table 7 on page 11, minor
28/29Doc ID 11481 Rev 7
STG3684A
y
Please Read Carefully:
Informatio n in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at an
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely respon sible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considere d as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo a re trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.