Sony XR-C5090 Service Manual

XR-C5090

SERVICE MANUAL

Refer to RM-X4S SERVICE MANUAL (9-925-698-∏) issued
previously for information of remote commander (RM-X4S)
supplied with this set

SPECIFICA TIONS

E Model

Model Name Using Similar Mechanism XR-C340
Tape T ransport Mechanism T ype MG-25F-136

MICROFILM

FM/AM CASSETTE CAR STEREO

SECTION 6

DIAGRAMS

6-1. IC PIN FUNCTION DESCRIPTION

• MAIN BOARD IC501 µPD17708GC-567-3B9 (SYSTEM CONTROLLER)

Pin No. Pin Name I/O Function

1 AMSSEL I Setting terminal for the AMS selection fixed at “L”
2 POS3 I
3 POS2 I
4 POS0 I
5 POS1 I
6 TAPEON O Tape system power supply on/off control signal output terminal “H”: tape on
7 CM ON O Capstan/reel motor (M901) drive signal output terminal “H”: motor on

8 LM LOD O

9 LM EJ O

10 TUNON O Tuner system power supply on/off control signal output to the BA3918 (IC611) “H”: tuner on
11 FM ON O FM system power supply on/off control signal output to the BA3918 (IC611) “H”: FM on
12 PW ON O Main system power supply on/off control signal output to the BA3918 (IC611) “H”: power on
13 MUT O Line muting control signal output terminal “H”: line muting on
14 VOLCE O Chip enable signal output to the electrical volume (IC331)
15 VOLCKO O Serial data transfer clock signal output to the electrical volume (IC331)
16 VOLSO O Serial data output to the electrical volume (IC331)
17 AMPON O Standby control signal output to the power amplifier (IC751) “L”: standby
18 AMPMUT O Muting control signal output to the power amplifier (IC751) “L”: muting on
19 DX/LO O Local/DX selection signal output to the FM/AM tuner unit (TU1) “L”: DX, “H”: local
20 AM MONO O AM forced monaural signal output terminal Not used (open)
21 GND — Ground terminal

22 DSTSEL I

23 DBASIN I D-BASS switch (SW951) input (A/D input)

24 KEYIN1 I

25 KEYIN0 I

26 RC IN0 I Rotary remote commander shift key A/D input terminal
27 VSM I FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)
28 AMIFIN I AM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)
29 FMIFIN I FM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)
30 VDD2 — Power supply terminal (+5V)
31 FM OSC I FM local oscillator detection signal input from the FM/AM tuner unit (TU1)
32 AM OSC I AM local oscillator detection signal input from the FM/AM tuner unit (TU1)
33 GND — Ground terminal
34 NCO O Not used (open)
35 EO1 O Main charge-pump control signal output terminal
36 TEST0 I Setting terminal for the test (fixed at “L”)
37 NCO O Not used (open)
38 SEKOUT O Seek control signal output to the FM/AM tuner unit (TU1)
39 MW/SW O MW/SW selection signal output to the FM/AM tuner unit (TU1) “L”: MW, “H”: SW
40 BEEP O Beep sound output terminal

Tape position detect input from tape operation switch on the mechanism block

Loading/tape operation motor control signal output to the LB1638M (IC351)
(For the loading direction and forward side operation) *1

Loading/tape operation motor control signal output to the LB1638M (IC351)
(For the eject direction and reverse side operation) *1

Destination setting terminal (frequency select switch (S502) input terminal)
“L”: AM 9k step or FM 50k step, “H”: AM 10k step or FM 200k step

Key input terminal (A/D input)
6, INTRO 1, REPEAT 2, SHUF 3, BL SKIP 6, ATA 5, 4, PRESET DISC +/– keys input
(LSW921 to LSW927, LSW929 and LSW930)

Key input terminal (A/D input)
OFF, SOURCE, MODE *, + ) + SEEK AMS, – = 0 SEEK AMS, VOLUME –,
SEL, VOLUME +, ATT , DSPL, BTM, LCL keys input (LSW901 to LSW912)

– 15 –