2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the power supply
voltage unless otherwise noted.
• T orque Measurement
ModeTorqu MeterMeter Reading
ForwardCQ-102C
Forward
Back Tension(0.01–0.07 oz•inch)
ReverseCQ-102RC
Reverse
Back Tension(0.01–0.07 oz•inch)
FF, REWCQ-201B
CQ-102C
CA-102RC
35–65 g•cm
(0.49–0.90 oz•inch)
0.5–5.0 g•cm
35–65 g•cm
(0.49–0.90 oz•inch)
0.5–5.0 g•cm
60–200 g•cm
(0.83–2.78 oz•inch)
TEST MODE
This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments
can be performed easier than it in ordinary procedure.
<Set the Test Mode>
1. Set the “OFF” mode.
2. Push the preset 4 button.
3. Push the preset 5 button.
4. Press the preset 1 button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.
<Release the Test mode>
1. Push the “OFF” button.
• T ape Tension Measurement
ModeTorqu MeterMeter Reading
ForwardCQ-403A
ReverseCQ-403R
more than 60 g
(more than 2.12 oz)
– 18 –
Page 19
See the adjustment location from on page 21 for the
FM
98.0
3
SHUF1
adjustment.
0 dB=0.775 VTAPE DECK SECTION
Tape Speed Adjustment
Procedure:
1. Put the set into the FWD PB mode.
speed checker
or
test tape
WS-48A
(3 kHz, 0 dB)
Specification: Constant speed
Speed checkerFrequency counter
–1.5 to +2.5%2,955 to 3,075 Hz
Adjustment Location: See page 21.
10 k Ω (XR-C340)
4
Ω
(XR-3740)
set
LINE OUT (XR-C340)
SPEAKER OUT (XR-3740)
frequency counter
+–
TUNER SECTION
Cautions during repair
When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair.
FM Auto Scan/Stop Level Adjustment
Setting:
SOURCE button: FM
FM RF signal
generator
Carrier frequency : 98.0 MHz
Output level: 22 dB (12.6
Mode: mono
Modulation: 1 kHz, 22.5 kHz deviation (30%)
Procedure:
1. Set to the test mode. (See page 18).
2. Push the SOURCE button and set to FM.
SHUF1
FM
0 dB=1 µV
antenna jack (J1)
0.01 µF
Display
98.0
set
µ
V)
3. Push the preset 3 button.
Display
4. Adjust with the volume RV2 on TU1 so that the “FM” indication turns to “FMI” indication on the display window.
But, in case of already indicated “FMI”, turn the RV2 so that
put out light “I” indication and adjustment.
L-CH Stereo separation: A-B
R-CH Stereo separation: C-D
The separations of both channels should be equal.
antenna jack (J1)
10 k
Ω
(XR-C340)
4
Ω
0.01 µF
set
Level meterLevel meter
connectionreading (dB)
(XR-3740)
LINE OUT (XR-C340)
SPEAKER OUT (XR-3740)
for minimum reading.
for minimum reading.
B
D
level meter
+
–
AM RF signal
generator
AM dummy antenna
(50 Ω)
Carrier frequency : 999 kHz
30% amplitude
modulation by
1 kHz signal
Output level: 33 dB
Procedure:
1. Set to the test mode. (See page 18.)
2. Push the SOURCE button and set to FM.
3. Push the MODE button and set to MW.
INTRO
SHUF1
4. Push the preset 3 button.
MW
44.7 µV
Display
999
Display
antenna jack (J1)
30
Ω
15 pF
65 pF
set
Specification: Separation more than 28dB
Adjustment Location: See page 21.
INTRO
SHUF1
5. Adjust with the volume RV1 on TU1 so that the “MW” indication turns to “MWI” indication on the display window.
But, in case of already indicated “MWI”, turn the R V1 so that
put out light “I” indication and adjustment.
INTRO
SHUF1
Adjustment Location: See page 21.
MW
999
Display
999
3
3
– 20 –
Page 21
Adjustment Location:
Tape Speed Adjustment
– SET UPPER VIEW –
TU1
RV1 AM (MW) Auto Scan/Stop Level Adjustment
RV2 FM Auto Scan/Stop Level Adjustment
RV4 FM Stereo Separation Adjustment
– 21 –
Page 22
SECTION 6
DIAGRAMS
6-1. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 µPD17707GC-521-3B9 (SYSTEM CONTROL) (XR-3740: TYPE2)
1ILLINIILLIN signal detection pin
2,3POS3, POS2ITape position detection pin
4,5POS0, POS1ITape position detection pin
6TAPEONOTape power supply control pin
7CM_ONOCapstan motor control pin
8LM_LODOLoading motor control pin (loadig direction)
9LM_EJOLoading motor control pin (eject direction)
10TUNONOTuner power supply control pin
11FM_ONOFM power supply control pin
12PW_ONOSystem power supply control pin
13MUTOSystem muting control pin At muting: “H”
14VOLCEOChip enable output pin to electrical volume
15VOLCKOOClock output pin to electrical volume
16VOLSOOData output pin to electrical volume
17AMPONOPower amp power supply control pin
18AMPMUTOPower amp muting control pin At muting: “L”
19DX_LOODX/local selection control pin
20AM_MONOOAM forced monaural signal output pin
21GND–GND
22DSTSEL1IDestination setting pin (A/D input)
23D-BASSID-BASS switch input pin (A/D input)
24,25
KEYIN1,KEYIN0
26RC_IN0IRotary remote commander input pin (A/D input)
27VSMIFM/AM signal meter voltage detection pin (A/D input)
28AMIFINIAM(MW, SW) IF input pin
29FMIFINIFM IF input pin
30VDD2–Power supply
31FM_OSCIFM OSC signal input pin
32AM_OSCIAM OSC signal input pin
33GND–GND
34N.C.–Not used
35EOIOMain charge-pump output pin
36TEST0ITest pin
37AM_STINIAM stereo signal input pin
38SEKOUTOSEEK control signal output pin
39MW_SWOMW/SW power supply select pin (Not used)
40BEEPOBeep sound output pin
41KEYACKOKey acknowledge signal input pin
42BU_INIBack up power supply detection pin
43MTLSELI/O
44DOLONI/OAt initial mode: valid/invalid selection input of DOLBY function
45AMSINITape music with/without detection pin “L”: with music
46STI/OStereo detection signal input and forced monaural signal output pin
IKey input pin (A/D input)
METAL control input/output pin
At initial mode: auto/manual selection input of METAL function. “L”: manual
At manual mode: METAL on/off output. “H”: on
At auto mode: input at %ª MTLIN
DOLBY control input/output pin
At normal mode: DOLBY on/off output
– 22 –
Page 23
Pin No.Pin NameI/OFunction
47AMS_ONOAt AMS: “L”
48N_ROUTOForward/reverse control pin
49TAPMUTOTape muting control pin At muting: “H”
Illumination power suply control pin
50ILLONOAt PW SEL on: ACC on: “H”
At PW SEL off: Power on: “H”
51SD_INIStation detection signal input pin
52NOSESWIFront panel removal or attaching detection pin
53TELMUTITelephone muting detection pin “L”: 20dB audio muting
54REL_TIReel table rotation detection pin
55ACCINIAccessory voltage detection pin
56TESTINITest mode setting pin
57RC_IN1IRotary remote commander input pin (A/D input)
58PW_SELIPower select switch input pin
59MTLINIAUTO METAL detection pin “L”: METAL
60KEYACTOPower supply control pin for A/D conversion
61KEYSEL0IKey function setting pin
62KEYSEL1IActive select pin for #• SEKOUT
63COLORIIllumination color setting pin “L”: amber, “H”: green
64LCDCEOLCD chip enable output pin
65LCDCKOOLCD clock output pin
66LCDSOOLCD data output pin
67LCDINHOLCD brank indication control pin
68UNICKIIClock input pin (for SONY BUS)
69UNISOOData output pin (for SONY BUS)
70UNISIIData input pin (for SONY BUS)
71UNICKOOClock output pin (for SONY BUS)
72BUSONOBUS ON control signai output pin (for SONY BUS)
73SYSRSTOSystem reset signal output pin
74VREGOCPU regurator output pin
75GND–GND
76X_OUTOSystem clock output pin (4.5 MHz)
77X_INISystem clock input pin (4.5 MHz)
78CEIFixed at “H”
79VDD1—Power supply
80RESETIReset input pin
– 23 –
Page 24
Page 25
Page 26
Page 27
• IC Block Diagrams
IC301 CXA2509AQ-T4
PBEQ1
PBOUT1
GND
120µ/
70µ
+
–
PBFB1
31
32
PBRIN1
1
PBEQ2
VCT
F2
F1
–
+
120µ/
70µ
345678 9 10
2
VCC
PBOUT2
PBREF1
PBFIN1
VCT
PBGND
PBFIN2
PBREF2
PBRIN2
PBFB2
33
34
35
36
37
38
39
40
TAPEIN1
X1
+
X1
TAPEIN2
AUXIN1
T1
AUXIN2
IC361 MM1322XFBE
1
DIREF
2425
T2
LPF
MSLPF
NR BIAS
TAPE/AUX
TAPE EQ
FWD/RVS
VCC
+
–
F3
–
+
LINEOUT2
+
OFF/B
NR
–
TCH2
2122232627282930
NR
OFF/B
MS
MODE
NR
MODE
DETECT
NC
PLAY
MS ON/
OFF
20
19
18
17
16
15
14
13
12
11
MSMODE
DRSW
TAPESW
INSW
NRSW
NC
MSOUT
DGND
MSTC
FF
MSSW
NC
TCH1
LINEOUT1
GND
IN2
VCC
IN1
8
OUT2
7
VS
2
3
CONTROL CIRCUIT
4
6
OUT1
5
GND
IC401 LC75373ED
LVRIN
+
–
34
LSELO
35
L4
L3
36
L2
VDD
RSELO
37
L1
38
39
R1
40
41
R2
R3
42
R4
43
44
+
–
–
+
–
+
1
RVRIN
LS1
LSIN
LT3
LT2
LCOM
23456 7 89 10
RCOM
LT1
+
–
+
–
+
–
–
+
RT1
RT2
RT3
LTOUT
–
+
DECODERLATCH
+
–
RS1
RSIN
RTOUT
LS2
–
+
–
+
+
–
+
–
RS2
LS3
RS3
SHIFT
REGISTER
LSOUT
2324252627282930313233
11
RSOUT
CONTROL
22
LFIN
+
–
+
–
–
+
–
+
LFOUT
21
LROUT
20
19
VREF
18
CE
17
DI
16
CL
15
VSS
14
RROUT
RFOUT
13
12
RFIN
– 37 –
Page 28
IC601 BA3918-V2
–
+
REGULATOR
OVER VOLTAGE
PROTECT
–
+
–
+
–
+
2 3
4
1
NC
STB
MODE2
MODE1
IC701 BA8270F-E2
BUS ON
1
2
RST
BATT
3
4
CLK
5
VREF
6
DATA
GND
78
BUS ON
SWITCH
RESET
SWITCH
BATTERY
SWITCH
5 678 9101211
VDD
AMP
VCC
14
13
12
11
10
9
ANT
VCC
RST
BUS ON
CLK IN
BU IN
DATA IN
DATA OUT
COM
AM
FM
GND
– 38 –
Page 29
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑↑
Parts Color Cabinet's Color
(1) CHASSIS SECTION
MG-52A-135
7
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
1613-928-669-01 LEVER (PINCH SELECTION)
1623-928-668-01 LEVER (MODE)
1633-933-338-01 SCREW (HP), STEP
1643-927-100-01 SCREW (+PS 2X10), SPECIAL
1653-928-670-01 SPRING (PINCH PRESS)
PL901 1-517-633-11 LAMP, PILOT
PL902 1-517-633-11 LAMP, PILOT
< RESISTOR >
R9011-216-647-11 METAL CHIP6800.5% 1/10W
R9021-216-647-11 METAL CHIP6800.5% 1/10W
R9031-216-647-11 METAL CHIP6800.5% 1/10W
R9041-208-437-41 METAL CHIP1K2%1/10W
R9051-216-655-11 METAL CHIP1.5K0.5% 1/10W
R9061-216-655-11 METAL CHIP1.5K0.5% 1/10W
R9071-208-445-41 METAL CHIP2.2K2%1/10W
R9081-208-449-41 METAL CHIP3.3K2%1/10W
R9091-208-453-41 METAL CHIP4.7K2%1/10W
R9101-216-671-11 METAL CHIP6.8K0.5% 1/10W
R9111-208-462-41 METAL CHIP10K2%1/10W
R9211-216-647-11 METAL CHIP6800.5% 1/10W
R9221-216-647-11 METAL CHIP6800.5% 1/10W
R9231-216-647-11 METAL CHIP6800.5% 1/10W
R9241-208-437-41 METAL CHIP1K2%1/10W
R9251-216-655-11 METAL CHIP1.5K0.5% 1/10W
R9261-216-655-11 METAL CHIP1.5K0.5% 1/10W
R9271-208-445-41 METAL CHIP2.2K2%1/10W
R9281-208-449-41 METAL CHIP3.3K2%1/10W
R9291-208-453-41 METAL CHIP4.7K2%1/10W
R9511-216-041-00 METAL CHIP4705%1/10W
R9521-216-089-00 METAL CHIP47K5%1/10W
R9531-216-049-11 METAL CHIP1K5%1/10W
R9541-216-049-11 METAL CHIP1K5%1/10W
R9551-216-049-11 METAL CHIP1K5%1/10W
R9561-216-049-11 METAL CHIP1K5%1/10W
R9611-216-027-00 METAL CHIP1205%1/10W
(GREEN)
R9611-216-033-00 METAL CHIP2205%1/10W
(AMBER)
R9621-216-025-00 METAL CHIP1005%1/10W
(GREEN)
R9621-216-031-00 METAL CHIP1805%1/10W
(AMBER)
R9631-216-025-00 METAL CHIP1005%1/10W
(GREEN)
R9631-216-031-00 METAL CHIP1805%1/10W
(AMBER)
R9641-216-035-00 METAL CHIP2705%1/10W
(GREEN)
R9641-216-037-00 METAL CHIP3305%1/10W
(AMBER)
R9651-216-035-00 METAL CHIP2705%1/10W
(GREEN)
R9651-216-037-00 METAL CHIP3305%1/10W
(AMBER)
– 44 –
Page 35
KEYMAIN
Ref. No.Part No.DescriptionRemark
R9661-216-033-00 METAL CHIP2205%1/10W
(GREEN)
R9661-216-035-00 METAL CHIP2705%1/10W
(AMBER)
R9811-216-655-11 METAL CHIP1.5K0.5% 1/10W
R9821-208-449-41 METAL CHIP3.3K2%1/10W
R9831-216-671-11 METAL CHIP6.8K0.5% 1/10W
R9841-216-081-00 METAL CHIP22K5%1/10W
IC3018-752-079-78 IC CXA2509AQ-T4
IC3618-759-395-97 IC MM1322XFBE
IC4018-759-443-67 IC LC75373ED
IC5018-759-449-87 IC uPD17707GC-521-3B9 (XR-3740: TYPE2)
IC5018-759-462-13 IC uPD17708GC-544-3B9 (XR-3740: TYPE1)
– 46 –
Page 37
MAIN
Ref. No.Part No.DescriptionRemark
IC5018-759-449-88 IC uPD17708GC-535-3B9 (XR-C340)
IC5028-759-363-81 IC XC61AN4002PR
IC6018-759-347-49 IC BA3918-V2
IC7018-759-449-89 IC BA8270F-E2 (XR-C340)
IC7518-759-369-41 IC HA13155
< JACK >
J11-764-808-14 JACK (ANT) (ANT IN)
J5011-764-270-21 JACK (REMOTE IN)
R21-249-417-11 CARBON1K5%1/4W
R31-249-417-11 CARBON1K5%1/4W
R41-247-843-11 CARBON3.3K5%1/4W
R61-216-073-00 METAL CHIP10K5%1/10W
R71-216-085-00 METAL CHIP33K5%1/10W
R81-216-093-00 METAL CHIP68K5%1/10W
R91-216-057-00 METAL CHIP2.2K5%1/10W
R101-216-049-11 METAL CHIP1K5%1/10W
R111-216-053-00 METAL CHIP1.5K5%1/10W
R121-249-421-11 CARBON2.2K5%1/4W
R141-216-065-00 METAL CHIP4.7K5%1/10W
(XR-3740)
R141-249-429-11 CARBON10K5%1/4W
(XR-C340)
R151-216-025-00 METAL CHIP1005%1/10W
(XR-3740)
R151-216-029-00 METAL CHIP1505%1/10W
(XR-C340)
R161-216-073-00 METAL CHIP10K5%1/10W
R1011-216-097-00 METAL CHIP100K5%1/10W
R1021-216-097-00 METAL CHIP100K5%1/10W
R1031-216-041-00 METAL CHIP4705%1/10W
R1041-216-109-00 METAL CHIP330K5%1/10W
R1051-216-077-00 METAL CHIP15K5%1/10W
R1071-216-214-00 METAL CHIP4.7K5%1/8W
R1081-216-081-00 METAL CHIP22K5%1/10W
R1191-216-065-00 METAL CHIP4.7K5%1/10W
(XR-C340)
R1511-216-065-00 METAL CHIP4.7K5%1/10W
R1521-216-073-00 METAL CHIP10K5%1/10W
R1611-216-061-00 METAL CHIP3.3K5%1/10W
R1711-216-182-00 METAL CHIP2205%1/8W
R1721-216-057-00 METAL CHIP2.2K5%1/10W
(XR-3740)
R1721-216-065-00 METAL CHIP4.7K5%1/10W
(XR-C340)
R1731-216-065-00 METAL CHIP4.7K5%1/10W
R1741-216-121-91 METAL CHIP1M5%1/10W
R1811-247-815-91 CARBON2205%1/4W
R1821-216-057-00 METAL CHIP2.2K5%1/10W
(XR-3740)
R1821-216-065-00 METAL CHIP4.7K5%1/10W
(XR-C340)
R1831-216-065-00 METAL CHIP4.7K5%1/10W
R1841-216-121-91 METAL CHIP1M5%1/10W
R2011-216-097-00 METAL CHIP100K5%1/10W
R2021-216-097-00 METAL CHIP100K5%1/10W
R2031-216-041-00 METAL CHIP4705%1/10W
R2041-216-109-00 METAL CHIP330K5%1/10W
R2051-216-077-00 METAL CHIP15K5%1/10W
R2071-216-214-00 METAL CHIP4.7K5%1/8W
R2081-216-081-00 METAL CHIP22K5%1/10W
R2191-216-065-00 METAL CHIP4.7K5%1/10W
(XR-C340)
R2411-216-073-00 METAL CHIP10K5%1/10W
(XR-C340)
R2511-216-065-00 METAL CHIP4.7K5%1/10W
R2521-216-073-00 METAL CHIP10K5%1/10W
– 47 –
Page 38
MAIN
Ref. No.Part No.DescriptionRemark
R2611-216-061-00 METAL CHIP3.3K5%1/10W
R2711-216-033-00 METAL CHIP2205%1/10W
R2721-216-057-00 METAL CHIP2.2K5%1/10W
(XR-3740)
R2721-216-065-00 METAL CHIP4.7K5%1/10W
(XR-C340)
R2731-216-065-00 METAL CHIP4.7K5%1/10W
R2741-216-121-91 METAL CHIP1M5%1/10W
R2811-216-033-00 METAL CHIP2205%1/10W
R2821-216-057-00 METAL CHIP2.2K5%1/10W
(XR-3740)
R2821-216-065-00 METAL CHIP4.7K5%1/10W
(XR-C340)
R2831-216-065-00 METAL CHIP4.7K5%1/10W
R2841-216-121-91 METAL CHIP1M5%1/10W
R3011-216-079-00 METAL CHIP18K5%1/10W
R3021-216-097-00 METAL CHIP100K5%1/10W
R3031-216-065-00 METAL CHIP4.7K5%1/10W
R3041-216-079-00 METAL CHIP18K5%1/10W
R3051-216-073-00 METAL CHIP10K5%1/10W
R3061-216-073-00 METAL CHIP10K5%1/10W
R3071-249-429-11 CARBON10K5%1/4W
R3081-216-109-00 METAL CHIP330K5%1/10W
R3511-216-049-11 METAL CHIP1K5%1/10W
R3521-249-385-11 CARBON2.25%1/6W
R3541-216-073-00 METAL CHIP10K5%1/10W
R3551-216-065-00 METAL CHIP4.7K5%1/10W
R3601-216-150-91 METAL CHIP105%1/8W
R4011-249-393-11 CARBON105%1/4W
R5011-216-097-00 METAL CHIP100K5%1/10W
R5021-216-073-00 METAL CHIP10K5%1/10W
R5031-216-097-00 METAL CHIP100K5%1/10W
R5041-216-246-00 METAL CHIP100K5%1/8W
R5081-216-073-00 METAL CHIP10K5%1/10W
R5091-216-222-00 METAL CHIP10K5%1/8W
R5111-216-097-00 METAL CHIP100K5%1/10W
R5121-216-049-11 METAL CHIP1K5%1/10W
R5131-216-049-11 METAL CHIP1K5%1/10W
R5141-216-049-11 METAL CHIP1K5%1/10W
R5151-216-097-00 METAL CHIP100K5%1/10W
R5161-216-097-00 METAL CHIP100K5%1/10W
R5171-216-097-00 METAL CHIP100K5%1/10W
R5181-216-097-00 METAL CHIP100K5%1/10W
R5191-216-097-00 METAL CHIP100K5%1/10W
R5201-216-097-00 METAL CHIP100K5%1/10W
R5211-216-097-00 METAL CHIP100K5%1/10W
(XR-C340/XR-3740: TYPE1)
R5221-216-097-00 METAL CHIP100K5%1/10W
R5231-216-097-00 METAL CHIP100K5%1/10W
R5241-216-097-00 METAL CHIP100K5%1/10W
R5251-216-097-00 METAL CHIP100K5%1/10W
R5271-216-097-00 METAL CHIP100K5%1/10W
R5281-216-097-00 METAL CHIP100K5%1/10W
R5291-216-097-00 METAL CHIP100K5%1/10W
R5301-216-097-00 METAL CHIP100K5%1/10W
R5311-249-429-11 CARBON10K5%1/4W
R5321-216-097-00 METAL CHIP100K5%1/10W
(XR-3740: TYPE2)
R5331-216-097-00 METAL CHIP100K5%1/10W
R5341-249-417-11 CARBON1K5%1/4W
Ref. No.Part No.DescriptionRemark
R5351-249-417-11 CARBON1K5%1/4W
R5361-216-097-00 METAL CHIP100K5%1/10W
R5381-249-413-11 CARBON4705%1/4W
R5391-249-413-11 CARBON4705%1/4W
R5431-249-413-11 CARBON4705%1/4W
R5441-216-097-00 METAL CHIP100K5%1/10W
R5451-249-413-11 CARBON4705%1/4W
R5461-208-806-11 METAL CHIP10K0.50% 1/10W
R5471-208-806-11 METAL CHIP10K0.50% 1/10W
R5491-208-806-11 METAL CHIP10K0.50% 1/10W
R5501-208-806-11 METAL CHIP10K0.50% 1/10W
R5511-216-025-00 METAL CHIP1005%1/10W
R5521-216-025-00 METAL CHIP1005%1/10W
R5531-216-097-00 METAL CHIP100K5%1/10W
R5541-216-295-00 CONDUCTOR, CHIP(2012)
R5611-216-065-00 METAL CHIP4.7K5%1/10W
R5621-249-429-11 CARBON10K5%1/4W
R5681-216-097-00 METAL CHIP100K5%1/10W
R5701-216-097-00 METAL CHIP100K5%1/10W
R5711-216-097-00 METAL CHIP100K5%1/10W
R5721-216-097-00 METAL CHIP100K5%1/10W
(XR-3740)
R7111-216-097-00 METAL CHIP100K5%1/10W
R7121-216-089-00 METAL CHIP47K5%1/10W
R7131-216-089-00 METAL CHIP47K5%1/10W
R7141-249-421-11 CARBON2.2K5%1/4W
R7351-216-134-00 METAL CHIP2.25%1/8W
R7361-216-134-00 METAL CHIP2.25%1/8W
R7451-216-134-00 METAL CHIP2.25%1/8W
R7461-216-134-00 METAL CHIP2.25%1/8W
R7751-216-134-00 METAL CHIP2.25%1/8W
R7761-216-134-00 METAL CHIP2.25%1/8W
R7851-216-134-00 METAL CHIP2.25%1/8W
R7861-216-134-00 METAL CHIP2.25%1/8W
R8511-216-025-00 METAL CHIP1005%1/10W
R8521-216-025-00 METAL CHIP1005%1/10W
R8531-216-041-00 METAL CHIP4705%1/10W
R8541-216-041-00 METAL CHIP4705%1/10W
R8551-216-041-00 METAL CHIP4705%1/10W
R8561-216-041-00 METAL CHIP4705%1/10W
R8571-216-049-11 METAL CHIP1K5%1/10W