Sony SLV-SE30UX, SLV-SE45UX User Manual

3-865-361-12 (1)

Video Cassette Recorder

Operating Instructions

PAL NTSC 4.43

SLV-SE30UX SLV-SE45UX

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Mains lead must only be changed at a qualified service shop.

Notice for customers in the United Kingdom

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. If the 13A fitted plug does not match the outlet socket in your home, please refer to your Appointed Sony Dealer for advice.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS1362, (i.e., marked with 2 or @ mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

Precautions

Safety

• This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.

• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

• The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.

Installing

• Allow adequate air circulation to prevent internal heat buildup.

• Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.

• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.

Caution

Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.

Compatible colour systems

This VCR is designed to record using the PAL colour system and play back using the PAL and NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed.

Introduction

Table of contents

Getting Started

4 Step 1: Unpacking 5 Step 2: Setting up the remote commander

9 Step 3: Connecting the VCR 13 Step 4: Setting up the VCR with the Auto Set Up function 14 Step 5: Tuning your TV to the VCR 16 Selecting a language 18 Presetting channels 21 Changing/disabling programme positions 27 Setting the clock 32 Setting your personal code

Getting Started

Basic Operations

34 Playing a tape 37 Recording TV programmes 42 Recording TV programmes using

the VIDEO Plus+* system

47 Setting the timer manually

Additional Information

66 Troubleshooting 69 Specifications 70 Index to parts and controls Back cover

Index

Additional Operations

50 Playing/searching at various

speeds

53 Setting the recording duration

time

54 Checking/changing/cancelling

timer settings

56 Searching using the Smart Search

function

59 Searching using the index

function

60 Adjusting the picture 62 Changing menu options 64 Editing with another VCR

* VIDEO Plus+ and PlusCode are trademarks applied for by Gemstar Development Corp. VIDEO

Plus+ system is manufactured under license from Gemstar Development Corporation.

Introduction

Getting Started

Step 1

Unpacking

Check that you have received the following items with the VCR:

• Remote commander

• R6 (size AA) batteries

• Aerial cable

Checking your model name

Getting Started

The instructions in this manual are for the 2 models: SLV-SE30UX and SE45UX. Check your model number by looking at the rear panel of your VCR. The SLV-SE30UX is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE45UX only.”

Step 2

Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.

Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.

Using the remote commander

You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the g symbol near the remote sensor, this remote commander will not operate the TV.

TV␣ ␣ /␣ ␣ VIDEO

Remote sensor

Getting Started

To operate

the VCR

a Sony TV

123 456

Set TV / VIDEO to

VIDEO and point at the remote sensor on the VCR

TV and point at the remote sensor on the TV

continued

Getting Started

Step 2 : Setting up the remote commander (continued)

WIDE

AUDIO MONITOR

FASTEXT buttons

I/u

;

DISPLAY

TV control buttons

Turn the TV into standby mode

Select an input source of the TV either from aerial in or from line in

Select the programme position of the TV

Adjust the volume of the TV

123 456 789

Press

I/u

… TV/VIDEO

Programme number buttons,

?, PROG +/–

Á +/–

… TV/VIDEO

Programme number buttons

PROG+/–/

√/◊ Á +/–

Getting Started

Switch to TV (Teletext off)

Switch to Teletext

Select the sound

Use FASTEXT

Call up on-screen display

Change the Teletext page

Switch to/from wide mode of a Sony wide TV (For other manufacture’s wide TV, see “Controlling other TVs with the remote commander” below.)

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one together.

• Do not use different types of batteries together.

• Some buttons may not work with certain Sony TVs.

Press

; (TV)

V (Teletext)

AUDIO MONITOR

FASTEXT buttons

DISPLAY

√/◊

WIDE

Controlling other TVs with the remote commander

The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the table below, set the appropriate manufacturer’s code number.

1 Set TV / VIDEO at the top of the remote commander to TV . 2 Hold down I/u, and enter your TV’s code number(s) using the

programme number buttons. Then release I/u. Now you can use the following TV control buttons to control your TV: I/u, TV/VIDEO, programme number buttons, ? (ten’s digit), PROG

+/–, Á +/–, ; (TV), V (Teletext), FASTEXT buttons, WIDE*, MENU*, >*/.*/?*//*, and OK*.

* These buttons may not work with all TVs.

Getting Started

Tip

• When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.

continued

Getting Started

Step 2 : Setting up the remote commander (continued)

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

To make wide mode settings, see the footnotes below this table for the applicable code numbers.

Manufacturer

Sony Akai Ferguson Grundig Hitachi JVC Loewe Mivar NEC Nokia

Code number

01*1, 02 68 52

10*1, 11* 24 33 45 09, 70 66 15, 16, 69*

Manufacturer

Panasonic Philips Saba Samsung Sanyo Sharp Telefunken Thomson Toshiba

Code number

17*1, 49 06*1, 07*1, 08* 12, 13 22, 23 25 29 36

43* 38

*1Press WIDE to switch the wide picture mode on or off. *2Press WIDE, then press Á +/– to select the wide picture mode you want. *3Press WIDE. The menu appears on the TV screen. Then, press >/./?// to

select the wide picture you want and press OK.

Notes

• If the TV uses a different remote control system from the one programmed to work

with the VCR, you cannot control your TV with the remote commander.

• If you enter a new code number, the code number previously entered will be erased.

• When you replace the batteries of the remote commander, the code number may

change. Set the appropriate code number every time you replace the batteries.

Getting Started

Step 3

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

Connecting the VCR

If your TV has a EURO-AV connector, see page 10.

If your TV does not have a EURO-AV (Scart) connector

AERIAL IN

Mains lead

to mains

Aerial cable (supplied)

: Signal flow

AERIAL OUT

1 Disconnect the aerial cable from your TV

and connect it to AERIAL IN on the rear panel of the VCR.

2 Connect AERIAL OUT of the VCR and

the aerial input of your TV using the supplied aerial cable.

AERIAL

ANTENNE

AERIAL IN

ENTREE

OUT

SORTIE

Getting Started

3 Connect the mains lead to the mains.

If the mains plug does not fit in the mains, use the supplied plug adaptor.

Note

• When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in the OPTIONS-2 menu to ON (initial setting) (see page 63).

continued

Getting Started

Step 3 : Connecting the VCR (continued)

If your TV has a EURO-AV (Scart) connector

AERIAL IN

Mains lead

: LINE-1 (TV)

AERIAL OUT

to mains

Aerial cable (supplied)

: Signal flow

EURO-AV cable (not supplied)

1 Disconnect the aerial cable from your

TV and connect it to AERIAL IN on the rear panel of the VCR.

2 Connect AERIAL OUT of the VCR and

the aerial input of your TV using the supplied aerial cable.

AERIAL IN

AERIAL

ANTENNE

AERIAL

ANTENNE

ENTREE

OUT

SORTIE

ENTREE

OUT

SORTIE

EURO-AV (Scart)

Getting Started

3 Connect LINE-1 (TV) on the VCR and

the EURO-AV (Scart) connector on the TV with the optional EURO-AV cable.

This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press … TV/ VIDEO to display the VIDEO indicator in the display window.

4 Connect the mains lead to the mains.

If the mains plug does not fit in the mains, use the supplied plug adaptor.

Note

• If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in the OPTIONS-2 menu to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 63). You do not have to tune your TV to the VCR. Skip “Tuning your TV to the VCR” on page 14.

About the SMARTLINK features

If the connected TV complies with SMARTLINK, MEGALOGIC*1, EASYLINK*2, Q-Link* the SMARTLINK function after you complete the steps on the previous page (the SMARTLINK indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.

, or EURO VIEW LINK*4, you can use

SMARTLINK

Getting Started

• Preset Download You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful, not to disconnect the cables or exit the Auto Set Up function during the procedure.

See “Setting up the VCR with the Auto Set Up function” on page 13.

continued

Getting Started

Step 3 : Connecting the VCR (continued)

• TV Direct Rec

You can easily record what you are watching on the TV (other than tapes being played on this VCR). For details, see “Recording what you are watching on the TV (TV Direct Rec)” on page 41.

• One Touch Play

With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play)” on page 36.

• One Touch Menu

You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander.

• One Touch Timer

You can turn on the VCR and TV, set the TV to the video channel, and display the timer recording menu (the TIMER METHOD menu, the TIMER menu, or the VIDEO PLUS+ menu) automatically by pressing commander.

You can set which timer recording menu is displayed using TIMER OPTIONS in the OPTIONS-2 menu (see page 63).

• Automatic Power Off

You can have the VCR turn off automatically, if the VCR is not used after you turn off the TV.

TIMER on the remote

*1“MEGALOGIC” is a registered trademark of Grundig Corporation. *2“EASYLINK” is a trademark of Philips Corporation. *3“Q-Link” is a trademark of Panasonic Corporation. *4“EURO VIEW LINK” is a trademark of Toshiba Corporation.

Note

• Not all the TVs respond to the functions above.

Getting Started

Step 4

Setting up the VCR with the Auto Set Up function

Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set TV channels, guide channels for the VIDEO Plus+ system, the RF channel, and VCR clock automatically.

AUTO SET UP

Getting Started

AUTO SET UP

To cancel the Auto Set Up function

Press AUTO SET UP.

Note

• Do not cancel the Auto Set Up function. If you do, repeat the step above.

Hold down AUTO SET UP on the VCR for more than three seconds. The VCR automatically turns on and VCR starts searching for all of

the receivable channels and presets them in the appropriate order for your local area.

If you use the SMARTLINK connection, the Preset Download function starts and the SMARTLINK indicator flashes in the display window during download.

After the search is complete, the current time appears in the display window for any stations that transmit a time signal. If the time does not appear, set the clock manually. See page 27.

Getting Started

Step 5

Tuning your TV to the VCR

If you have connected the VCR to your TV using the EURO-AV cable, skip this step.

RF CHANNEL

1 Press RF CHANNEL on the VCR lightly.

RF CHANNEL

The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.

2 Turn on your TV and select a programme position for the VCR

picture. This programme position will now be referred to as the video

channel.

Getting Started

3 Tune the TV to the same channel as that

shown in the display window so that the picture on the right appears clearly on the TV screen.

Refer to your TV manual for tuning instructions.

If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below.

4 Press RF CHANNEL.

RF CHANNEL

To check to see if the TV tuning is correct

Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.

To obtain a clear picture from the VCR

If the screen does not appear clearly in step 3 above, press PROGRAM +/–, so that another RF channel appears. Then tune the TV to the new RF channel until a clear picture appears.

You have now tuned your TV to the VCR. Whenever you want to play a tape, set the TV to the video channel.

SONY VIDEO CASSETTE RECORDER

Getting Started

Selecting a

SET :

SELECT :

MENUEXIT :

LANGUAGE

DEUTSCH FRANÇAIS ITALIANO ESPAÑOL PORTUGUÊS NEDERLANDS

EΛΛHNIKA

ENGLISH

language

If you prefer an on-screen language other than English, use the on-screen display to select another language.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

1 Press MENU, then press >/. to

highlight SETTINGS and press OK.

PLAY

2 Press >/. to highlight LANGUAGE,

PLAY

then press OK.

TUNER CLOCK LANGUAGE

RETURN

SELECT : SET :

SETTINGS

>/. OK

MENUEXIT :

3 Press >/. to highlight the desired language, then press OK.

PLAY

Getting Started

4 Press MENU to exit the menu.

Tip

• If you want to return to the previous menu, highlight RETURN and press OK.

Note

• The menu disappears automatically if you don’t proceed for more than a few minutes.

Getting Started

Presetting channels

If some channels could not be preset using the Auto Set Up function, you can preset them manually.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

1 Press MENU, then press >/. to

highlight SETTINGS and press OK.

PLAY

TUNER CLOCK LANGUAGE

RETURN

SELECT : SET :

SETTINGS

PROG +/–

>/./?// OK

MENUEXIT :

2 Press >/. to highlight TUNER, then

PLAY

• PROG

3 Press PROG +/– to select the

Getting Started

press OK.

programme position.

TUNER

CHANNEL SET AFT FINE TUNING

RETURN

SELECT : SET :

Selected programme position

TUNER

CHANNEL SET AFT FINE TUNING

RETURN

SELECT : SET :

C ON

PROG. 1

AAB12

MENUEXIT :

PROG. 4

AAB12

MENUEXIT :

4 Press >/. to highlight CHANNEL SET,

MENUEXIT :

TUNER

AAB12

PROG.

CHANNEL SET AFT FINE TUNING

RETURN

CONFIRM :

SELECT :

MENUEXIT :

TUNER

PROG.

CHANNEL SET AFT FINE TUNING

RETURN

CONFIRM :

SELECT :

PLAY

then press OK.

5 Press >/. repeatedly until the channel you want is displayed.

PLAY

The channels appear in the following order:

• UHF B21 - B69 If you know the number of the channel

you want, press the programme number buttons. For example, for channel 5, first press “0” and then press “5.”

6 To allocate another channel to another programme position, repeat

steps 3 and 5.

7 Press MENU to exit the menu.

Getting Started

Disabling unwanted programme positions

After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons.

1 In step 5 above, press programme number button “0” twice to display

the number “00” beside CHANNEL SET.

2 Press MENU to exit the menu.

continued

Getting Started

Presetting channels (continued)

If the picture is not clear

Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture is not clear, you may also use the manual tuning function.

1 Press PROG +/– or the programme number buttons to select the

programme position for which you cannot obtain a clear picture.

2 Press MENU, then select SETTINGS and press OK. 3 Select TUNER, then press OK. 4 Select FINE TUNING, then press OK.

The fine tuning meter appears.

TUNER

CHANNEL SET AFT FINE TUNING

RETURN

PROG.

Selected programme position

SET :

MENUEXIT :

5 Press ?// to get a clearer picture, then press MENU to exit the

menu. Note that the AFT (Auto Fine Tuning) setting switches to OFF.

Tip

• If you want to return to the previous menu, highlight RETURN and press OK.

Note

• The menu disappears automatically if you don’t proceed for more than a few

minutes.

Getting Started

Changing/ disabling programme positions

After setting the channels, you can change the programme positions and the station names as you like. If any programme positions are unused or contain unwanted channels, you can disable them. If the station names are not displayed, you can enter them manually (see page 23).

Changing programme positions

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

1 Press MENU, then press >/. to

highlight LISTS and press OK.

PLAY

LISTS

CHANNEL LIST TIMER LIST

RETURN

SELECT : SET :

>/.//

Getting Started

MENUEXIT :

2 Press >/. to highlight CHANNEL LIST,

PLAY

then press OK.

CHANNEL LIST

PROG

SELECT : MOVE PROG:: ERASE PROG

CH C C C C C

CLEAR

NAME

AAB

CDE

FGH

1 2 3 4 5

continued

Getting Started

MENUEXIT :

Changing/disabling programme positions (continued)

3 Press >/. to highlight the row on which

PLAY

you want to change the programme position, then press /.

To display other pages for programme positions 6 to 60, press >/. repeatedly.

4 Press >/. until the selected channel row

PLAY

moves to the desired programme position.

The selected channel is inserted at the new programme position and the intermediate channels are displaced to fill the gap.

CHANNEL LIST

PROG

SELECT : SET STATION NAME:: CONFIRM

CHANNEL LIST

PROG

1 27

SELECT : SET STATION NAME:: CONFIRM

NAME

AAB

CDE

FGH

3 6 2

NAME CDE

AAB FGH

MENUEXIT :

5 Press OK to confirm the setting.

PLAY

6 To change the programme position of another station, repeat steps 3

to 5.

7 Press MENU to exit the menu.

Getting Started

Tip

• If you want to return to the previous menu, highlight RETURN and press OK.

Note

• The menu disappears automatically if you don’t proceed for more than a few minutes.

Changing the station names

You can change the station names (up to 5 characters).

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

1 Press MENU, then press >/. to

highlight LISTS and press OK.

PLAY

2 Press >/. to highlight CHANNEL LIST,

PLAY

then press OK.

LISTS

CHANNEL LIST TIMER LIST

RETURN

SELECT : SET :

CHANNEL LIST

PROG

SELECT : MOVE PROG:: ERASE PROG

C C

4 5

CLEAR

>/./?// OK

NAME

AAB

CDE

FGH

Getting Started

MENUEXIT :

3 Press >/. to highlight the row on which

PLAY

you want to change the station name, then press /.

To display other pages for programme positions 6 to 60, press >/. repeatedly.

CHANNEL LIST

PROG

SELECT : SET STATION NAME:: CONFIRM

NAME

AAB

CDE

6 27 0

FGH

MENUEXIT :

continued

Getting Started

+ 53 hidden pages