Operating Instructions
Manual de instrucciones
######
For installation and connections, see the supplied installation/connections
manual.
Para obtener información sobre la instalación y las conexiónes, consulte el manual
de instalación/conexiones suministrado.
##################################
EN
ES
C
MDX-C670
1997 by Sony Corporation
EN
Welcome !
Thank you for purchasing the Sony MiniDisc
Player. This unit lets you enjoy a variety of
features by using a rotary remote.
In addition to the MD playback and the radio
operations, you can expand your system by
connecting an optional CD/MD changer.
If you connect an optional CD changer with
the CD-TEXT function, the CD-TEXT
information will appear in the display when
you play back a CD-TEXT disc*.
* A CD-TEXT disc is an audio CD that includes
information such as the disc name, artist name and truck
names. This information is recorded on the disc.
2
Table of Contents
This Unit Only
Getting Started
Resetting the unit ................................................ 4
Detaching the front panel .................................. 4
Preparing the rotary remote .............................. 4
Setting the clock .................................................. 5
MD Player
Listening to an MD ............................................. 5
Playing an MD in various modes ..................... 6
Radio
Memorising stations automatically
— Best Tuning Memory (BTM) ................... 7
Memorising only the desired stations.............. 8
Receiving the memorised stations.................... 8
Storing the station names
— Station Memo ............................................ 9
Index ................................................................... 22
EN
3
EN
Getting Started
Resetting the unit
Before operating the unit for the first time or
after replacing the car battery, you must reset
the unit.
Press the reset button with a pointed object,
such as a ballpoint pen.
Reset button
Note
Pressing the reset button will erase the clock and some
memorized functions.
Attaching the front panel
Align part A of the front panel to part B of
the unit as illustrated, and push until it clicks.
A
B
Notes
• Be sure not to attach the front panel upside down.
•Do not press the front panel hard against the unit when
attaching it. Press it lightly against the unit.
•Do not press hard or put excessive pressure on the
display windows of the front panel.
•Do not expose the front panel to direct sunlight, heat
sources such as hot air ducts, and do not leave it in a
humid place. Never leave it on the dashboard of a car
parked in direct sunlight where there may be a
considerable rise in temperature.
Detaching the front panel
You can detach the front panel of this unit to
prevent the unit from being stolen.
1 Press (OFF).
2 Press (RELEASE) to open up the front
panel. Then slide the front panel a little
to the left, and pull it off towards you.
(OFF)
(RELEASE)
Notes
• Be sure not to drop the panel when detaching it from the
unit.
• If you press (RELEASE) to detach the panel while the
unit is still on, the unit will turn off automatically to
prevent the speakers from being damaged.
• When you carry the front panel with you, put it in the
supplied front panel case.
Caution alarm
If you turn the ignition key switch to the OFF
position without removing the front panel, the
caution alarm will beep for a few seconds
(only when the POWER SELECT switch is set
to the A position).
Preparing the rotary
remote
When you mount the rotary remote, attach the
label in the illustration below.
SOUND
MODE
LIST
MODE
SOUND
LIST
4
Setting the clock
The clock has a 12-hour digital indication.
Example: Set the clock to 10:08
1 Press (SHIFT), then press (2) (SET UP).
Set
EQSUR
Clock
SET UP
1 Press (4) (n).
Set
EQSUR
1:‚‚
SET UP
The hour digit flashes.
2 Set the hour.
SET UP
SET UP
SET UP
1‚:‚‚
1‚:‚‚
1‚:‚8
1‚:‚8
to go backward
to go forward
to go backward
to go forward
SOURCE
Set
EQSUR
3 Press (4) (n).
Set
EQSUR
The minute digits flash.
4 Set the minute.
SOURCE
Set
EQSUR
2 Press (SHIFT).
EQSUR
SET UP
The clock starts.
3 Press (SHIFT).
When the mode setting is complete, the
normal playback mode appears.
Note
If the POWER SELECT switch on the bottom of the unit is
set to the B position, turn the power on first, then set the
clock.
MD Player
Listening to an MD
Simply insert the MD.
Playback starts automatically.
Labeled side up
If an MD is already inserted, press (SOURCE)
repeatedly until “MD” appears.
The title of the MD* and the track title will be
displayed on the display window, then the
playing time will appear.
Elapsed playing time
MD
EQSUR
* Only if these titles are prerecorded on the MD.
Tip
If the name of the MD is too long, you can scroll it across
the display window by pressing (SCRL) while the disc
name or track name is displayed.
When the last track on the MD is
over
the track number indication will return to “1,”
and the playback will restart from the first
track of the MD.
ToPress
Stop playback6 or (OFF)
Eject the MD6
TRACK
3 1.‚1
Truck number
EN
Getting Started/MD Player
5
EN
PLAY MODE
EQSUR
MD
Intro off
Changing the displayed items
Each time you press (DSPL), the item changes
as follows:
Elapsed playback time
1
*
If there is no prerecorded title for a disc “NO D.Name”
will appear on the display.
2
If a track title is not prerecorded, “NO T.Name” will be
*
displayed.
$
$
Disc name*
$
Track name*
$
Clock
1
2
Automatically scrolling a disc name
— Auto Scroll
If the disc name or track name on an MD
exceeds 10 characters and the Auto Scroll
function is on, automatically scrolls on the
display as follows:
• The disc name appears when the disc has changed (if the
disc name is selected).
• The track name appears when the track has changed (if
the track name is selected).
• The disc or track name appears depending on the setting
when you press (SOURCE) to select an MD.
If you press (DSPL) to change the display
item, the disc or track name of the MD is
scrolled automatically whether you set the
function on or off.
1 During playback, press (SHIFT).
2 Press (2) (SET UP) repeatedly until
To cancel Auto Scroll, select “A.Scrl off” in
step 2 above.
Displaying the recording date of
the currently selected MD
Press (SCRL) for two seconds during MD
playback.
The recording date of the track is displayed
for about three seconds.
Locating a specific track
— Automatic Music Sensor (AMS)
During playback, press either side of
(SEEK/AMS) momentarily.
To locate succeeding tracks
To locate preceding tracks
Locating a specific point in a track
— Manual Search
During playback, press and hold either
side of (SEEK/AMS). Release the button
when you have found the desired point.
To search forward
To search backward
Note
If “
means you have reached the beginning or the end of the
disc and you cannot go any further.
” or “” appears in the display, that
Playing an MD in various
modes
You can play MDs in various modes:
•Intro (Intro Scan) lets you play the first 10
seconds of all the tracks.
•Repeat (Repeat Play) repeats the current
track.
•Shuf (Shuffle Play) plays all the tracks in
random order.
Scanning for the desired track
— Intro scan
1 During playback, press (SHIFT).
Every time you press (SHIFT), only the
items you can select light up.
SET UP PLAY MODE
SHIFT
1
234567
2 Press (3) (PLAY MODE).
REPSHUF
6
3 Press (4) (n) to select “Intro on.”
MD
EQSUR
Intro on
PLAY MODE
Playback starts.
INTRO
Radio
4 Press (SHIFT).
To go back to the normal playback mode,
select “Intro off” in step 3 above.
Playing tracks repeatedly
— Repeat Play
1 During playback, press (SHIFT).
2 Press (6) (REP) repeatedly until
“Repeat 1” appears.
SET UP PLAY MODE
SHIFT
1
234567
Repeat play starts.
REPSHUF
3 Press (SHIFT).
To go back to the normal playback mode,
select “Repeat off” in step 2 above.
Playing tracks in random order
— Shuffle Play
1 During playback, press (SHIFT).
2 Press (7) (SHUF) repeatedly until
“Shuf 1” appears.
SET UP PLAY MODE
SHIFT
1
234567
Shuffle play starts.
REPSHUF
3 Press (SHIFT).
To go back to the normal playback mode,
select “Shuf off” in step 2 above.
Memorising stations
automatically
— Best Tuning Memory (BTM)
The unit selects the stations with the strongest
signals and memorises them in the order of
their frequencies. You can store up to 10
stations on each band (FM1, FM2 and AM (or
AM1, AM2)*).
Caution
When tuning in the station while driving, use
Best Tuning Memory to prevent accidents.
1 Press (SOURCE) repeatedly to select the
tuner.
Each time you press (SOURCE), the source
changes as follows:
MD ˜ TUNER
2 Press (MODE) repeatedly to select the
band.
Each time you press (MODE), the band
changes as follows:
” FM1 ” FM2 ” AM (or AM1 ”AM2)*
3 Press (SHIFT), then press (3) (PLAY
MODE) repeatedly until “B.T.M” appears.
4 Press (4) (n).
The unit stores stations in the order of their
frequencies on the number buttons.
A beep sound and the setting is stored.
5 Press (SHIFT).
* When you set the frequency select switch to the 9K
position.
Notes
• The unit does not store stations with weak signals. If
only a few stations are received, some number buttons
will retain heir former setting.
• When a number is indicated in the display, the unit
starts storing stations from the one currently displayed.
EN
MD Player/Radio
7
EN
Memorising only the
desired stations
You can store up to 10 stations on each band
(20 for FM1 and FM2, 10 for AM (or AM1 and
AM2)*) in the order of your choice.
1 Press (SOURCE) repeatedly to select the
tuner.
2 Press (MODE) repeatedly to select the
band (FM1, FM2 or AM (AM1, AM2)*).
3 Press either side of (SEEK/AMS) to tune
in the station that you want to store on
the number button.
4 Press the desired number button for two
seconds until “MEM” appears.
The number button indication appears in
the display.
* When you set the frequency select switch to the 9K
position.
Note
If you try to store another station on the same number
button, the previously stored station will be erased.
Receiving the memorised
stations
1 Press (SOURCE) repeatedly to select the
tuner.
2 Press (MODE) repeatedly to select the
band (FM1, FM2 or AM (AM1, AM2)*).
3 Press the number button ((1) to (10))
momentarily where the desired station is
stored.
* When you set the frequency select switch to the 9K
position.
If you cannot tune in a preset
station
Press either side of (SEEK/AMS)
momentarily to search for the station
(automatic tuning).
Scanning stops when the unit receives a
station. Press either side of (SEEK/AMS)
repeatedly until the desired station is
received.
Note
If the automatic tuning stops too frequently, press
(SHIFT), then press (3) (PLAY MODE) repeatedly until
“Local” (local seek mode) is displayed. Then press (4)
(n) to select “Local on”. Press (SHIFT).
Only the stations with relatively strong signals will be
tuned in.
Tip
If you know the frequency of the station you want to listen
to, press and hold either side of (SEEK/AMS) until the
desired frequency appears (manual tuning).
If FM stereo reception is poor
— Monaural Mode
1 Press (SHIFT), then press (3) (PLAY
MODE) repeatedly until “Mono” is
appears.
2 Press (4) (n) repeatedly until “Mono
on“ appears.
The sound improves, but becomes
monaural (“ST” disappears).
3 Press (SHIFT).
To go back to the normal mode, select
“Mono off” in step 2 above.
Changing the displayed items
Each time you press (DSPL), the items changes
as follows:
Frequency ˜ Clock
8
Storing the station names
—Station Memo
You can assign a name to each radio station
and store it in memory. The name of the
current station appears in the display. You can
store up to eight characters for each station.
Storing the station names
1 Tune in a station whose name you want
to store.
2 Press (LIST) for two seconds.
FM1
EQSUR
________
Displaying the station name
Press (DSPL) during radio reception.
FM1
EQSUR
3 WRKISS
Each time you press (DSPL), the item
changes as follows:
z Station name* z Frequency z Clock
* If the station name is not stored, “NO Name”
appears in the display for one second.
Erasing the station name
1 Tune in any station and press (LIST) for
two seconds.
3 Enter the characters.
1 Rotate the dial clockwise direction to
select the desired characters.
(A n B n C n ··· Z n 0 n 1 n 2 n
··· 9 n + n – n*n / n \ n > n <
n . n _ )
FM1
EQSUR
W_______
If you rotate the dial counterclockwise,
the characters appear in the reverse
order.
If you want to put a blank space
between characters, select “_” (underbar).
2 Press (4) (n) after locating the
desired character.
The flashing cursor moves to the next
space.
FM1
EQSUR
W_______
If you press (1) (N), the flashing cursor
moves to the left.
3 Repeat steps 1 and 2 to enter the
entire name.
4 To return to normal radio reception,
press (LIST) for two seconds.
Tip
To erase/correct a name, enter “_” (under-bar) for each
character.
2 Press (DSPL) for two seconds.
“Delete” and the station name appear in the
display.
3 Rotate the dial to select the name you
want to erase.
4 Press (5) (ENTER) for two seconds.
The name is erased.
Repeat steps 3 and 4 if you want to erase
other names.
5 Press (LIST) for two seconds.
The unit returns to normal radio reception
mode.
Locating a station by
name
1 Press (LIST) momentarily.
2 Press (LIST) repeatedly until you find the
3 Press (5) (ENTER) to tune in the desired
— List-up
The name assigned to the current station
appears in the display.
LST
EQSUR
3 WRKISS
ENTER
desired station.
station.
EN
Radio
Note
After the station name or frequency has been displayed for
five seconds, the display goes back to normal mode. To turn
off the display, press (DSPL).
9
Other Functions
Using the rotary remote
The rotary remote works by pressing buttons
and/or rotating controls.
You can control the optional CD or MD
changer with the rotary remote.
By pressing the button (the
SOURCE and MODE buttons)
(SOURCE)
By pressing in and rotating the
control (the PRESET/DISC control)
Push in and rotate the control to:
•Receive the stations memorised on the
number buttons.
•Change the disc.
Other operations
Rotate the VOL control to
adjust the volume.
Press (MUTE) to
mute the sound.
EN
Every time you press (SOURCE), the
source changes as follows:
Tuner n CD n MD
Pressing (MODE) changes the operation
in the following ways:
• Tuner: FM1 n FM2 n AM (or AM1 n AM2)
• CD changer: CD1 n CD2 n …
• MD changer: MD1 n MD2 n …
Tip
When the POWER SELECT switch is set to position B,
you can turn on this unit by pressing (SOURCE) on the
rotary remote.
By rotating the control (the SEEK/
AMS control)
Rotate the control momentarily and
release it to:
•Locate a specific track on a disc. Rotate
and hold the control until you locate the
specific point in a track, then release it to
start playback.
•Tune in the stations automatically. Rotate
and hold the control to tune in the specific
10
station.
(MODE)
OFF
Press (OFF) to turn
off the unit.
Press (SOUND) to adjust the
volume and sound menu.
Press (LIST) to display the
memorised names.
Changing the operative direction
The operative direction of controls is factoryset as in the illustration below.
To increase
To decrease
If you need to mount the rotary remote on the
right side of the steering column, you can
reverse the controls operative direction.
Press (SOUND) two seconds while
pushing the VOL control.
Tip
You can control the operative direction of controls with the
unit.
Adjusting the sound
characteristics
You can adjust bass, treble, balance and fader.
Each source can store the bass and treble levels
respectively.
1 Select the item you want to adjust by
pressing (SOUND) repeatedly.
VOL (volume) n BAS (bass) n TRE
(treble) n BAL (balance) n FAD (fader)
2 Adjust the selected item by rotating the
dial.
Adjust within three seconds after selecting
the item. (After three seconds, the dial
functions as the volume control.)
Muting the sound
Press (MUTE) on the rotary remote.
“Mute on” flashes momentarily.
To restore the previous volume level, press
(MUTE) again.
Tip
The unit decreases the volume automatically when a
telephone call comes in (Telephone-mute function).
Changing the sound and
display settings
You can set:
•Clock (page 5)
•D.Info (Dual Information) to display the
clock and the play mode at the same time
(ON) or to display the information
alternately (OFF).
•Amber/Green to change the illumination
color to amber or green.
•Dimmer to change the brightness of the
display.
— Select “Auto” to dim the display only
when you turn the lights on.
— Select “on” to dim the display.
•Contrast to adjust the contrast if the
indications in the display are not
recognizable because of the unit’s installed
position.
•Beep to turn on or off the beeps.
•RM (Rotary Remote) to change the operative
direction of the controls of the rotary remote.
— Select “norm” to use the rotary remote as
the factory preset position.
— Select “rev” when you mount the rotary
remote on the right of the steering
column.
•Loud (Loudness) to enjoy bass and treble
even at low volume. Bass and treble will be
reinforced.
•A. Scrl (Auto Scroll) (page 6 and 12)
•Disc MEMO/TEXT name (Disc memo/CDTEXT name) (page 14)
1 Press (SHIFT).
2 Press (2) (SET UP) repeatedly until the
desired setting mode appears.
Each time you press (2) (SET UP), the item
changes as follows:
Clock n D.Info* n Amber/Green n Dimmer
n Contrast n Beep n RM n Loud* n
A.Scrl* n Disc MEMO/TEXT name*
* When you have not turn the station or there is no
CD/MD being played, these items will not appear.
Note
The displayed item will differ depending on the source.
3 Press (4) (n) to select the desired
setting (for example: on or off).
At “Contrast” setting, pressing (4) (n)
makes the contrast higher, and pressing (1)
(N) makes the contrast lower.
4 Press (SHIFT).
When the mode setting is complete, the
normal playback mode appears.
EN
Other Functions
11
With Optional Equipment
CD/MD Changer
You can control up to 7 CD changers and MD
changers with this unit.
If you connect an optional CD changer with
the CD-TEXT function, the CD-TEXT
information will appear in the display when
you play back a CD-TEXT disc.
Automatically scrolling a disc name
— Auto Scroll
If the disc name/artist name or track name on
a CD-TEXT disc or MD exceeds 10 characters
and the Auto Scroll function is on,
automatically scrolls on the display as follows:
• The disc name appears when the disc has changed (if the
disc name is selected).
• The track name appears when the track has changed (if
the track name is selected).
• The disc or track name appears depending on the setting
when you press (SOURCE) to select an MD or CDTEXT disc.
EN
Playing a CD or an MD
1 Press (SOURCE) repeatedly to select the
CD or MD.
2 Press (MODE) until the desired changer
appears.
CD/MD playback starts.
When a CD or an MD changer is connected, all
the tracks play from the beginning.
Changing the displayed items
Each time you press (DSPL) during CD, CDTEXT, or MD playback, the item changes as
follows:
Elapsed playback time
Disc name*
1
*
If you have not labeled the disc or there is no disc name
prerecorded on the MD, “NO D.Name” appears in the
display.
2
If you play a CD-TEXT disc, the artist name appears in
*
the display after the disc name. (Only for CD-TEXT
discs with the artist name)
3
If the track name of a CD-TEXT disc or MD is not
*
prerecorded, “NO T.Name” appears in the display.
You can label a personalized name for CDs
and CD-TEXT discs with the disc memo
function, refer to “Labeling a CD” (page 13).
$
$
1
/Artist name*
$
Track name*
$
Clock
2
3
If you press (DSPL) to change the display
item, the disc or track name of the MD or CDTEXT disc is scrolled automatically whether
you set the function on or off.
1 During playback, press (SHIFT).
2 Press (2) (SET UP) repeatedly until
To cancel Auto Scroll, select “A.Scrl off” in
step 2 above.
Locating a specific track
— Automatic Music Sensor (AMS)
During playback, press either side of
(SEEK/AMS) once for each track you
want to skip.
To locate succeeding tracks
To locate preceding tracks
Locating a specific point in a track
— Manual Search
During playback, press and hold either
side of (SEEK/AMS). Release the button
when you have found the desired point.
To search forward
To search backward
Tip
If the name of the MD or CD-TEXT disc is too long, you
can scroll it across the display by pressing (SCRL) while
the disc name or track name is displayed.
12
Locating a disc by disc number
EQSUR
DISC NAME
CD2
1 S_______
— Direct Disc Selection
Press the number button that
corresponds with the desired disc
number.
The desired disc in the currently selected
changer begins playback.
Scanning the tracks
— Intro Scan
You can play the first 10 seconds of all the
tracks on the currently selected disc.
1 During playback, press (SHIFT), then
press (3) (PLAY MODE) repeatedly until
“Intro” appears.
2 Press (4) (n) to select “Intro on.”
Intro Scan starts.
3 Press (SHIFT).
To go back to the normal playback mode,
select “Intro off” in step 2 above.
Playing tracks repeatedly
— Repeat Play
You can select:
•Repeat 1 to repeat a track.
•Repeat 2 to repeat a disc.
•Repeat 3 to repeat all the discs in the current
changer.
1 During playback, press (SHIFT).
2 Press (6) (REP) repeatedly until the
desired setting appears.
z Repeat 1 z Repeat 2 z Repeat 3
Repeat off Z
Repeat Play starts.
3 Press (SHIFT).
Playing tracks in random
order
You can select:
•Shuf 1 to play the tracks on the current disc
in a random order.
•Shuf 2 to play the tracks in the current
changer in a random order.
•Shuf 3 to play all the tracks in a random
order.
1 During playback, press (SHIFT).
2 Press (7) (SHUF) repeatedly until the
3 Press (SHIFT).
To go back to the normal playback mode,
select “Shuf off” in step 2 above.
— Shuffle Play
desired setting appears.
z Shuf 1 z Shuf 2 z Shuf 3
Shuf off Z
Shuffle Play starts.
Labeling a CD — Disc Memo
(CD changer with custom file function)
You can label each disc with a personalized
name. You can enter up to eight characters for
a disc. If you label a CD, you can locate a disc
by name and select the specific tracks for
playback (page 15).
1 Play the CD and press (LIST) for two
seconds.
CD2
2 Enter the characters.
1 Rotate the dial in a clockwise
DISC NAME
EQSUR
1 ________
direction to select the desired
characters.
(A n B n C n ··· Z n 0 n 1 n 2 n
··· 9 n + n – n*n / n \ n > n <
n . n _ )
EN
CD/MD Changer
To go back to the normal playback mode,
select “Repeat off” in step 2 above.
continue to next page n
13
EN
If you rotate the dial in a
counterclockwise direction, the
characters appear in the reverse order.
If you want to put a blank space
between characters, select “_” (underbar).
2 Press (4) (n) after locating the
desired character.
The flashing cursor moves to the next
space.
CD2
DISC NAME
EQSUR
1 S_______
If you press (1) (N), the flashing cursor
moves to the left.
3 Repeat steps 1 and 2 to enter the
entire name.
3 To return to the normal CD playback
mode, press (LIST) for two seconds.
Tip
To erase/correct a name enter “_” (under-bar) for each
character.
Displaying the disc memo name or
CD-TEXT name
When you play back a CD-TEXT disc, you can
set the priority display item to be the disc
memo name or the CD-TEXT name.
1 Press (SHIFT) during CD-TEXT disc
playback.
2 Press (2) (SET UP) repeatedly until “Disc
MEMO” or “TEXT name” appears.
3 Press (4) (n) to select “Disc MEMO” or
“TEXT name.”
4 Press (SHIFT).
After the mode setting is complete, the
display goes back to normal playback
mode.
If you want to change to the other setting, you
can do so in step 3.
Displaying the disc memo name
During CD playback, press (DSPL) .
CD2
DISC NAME
EQSUR
1 SCHUBERT
14
Each time you press (DSPL) during CD
playback, the item changes as follows:
Elapsed playback time
Disc name/Artist name*
1
When you connect an optional CD changer with the CD-
*
TEXT function, the personalized label or the CD-TEXT
disc name appears. See below to change the display.
- To change the displayed item press (4) (n).
- To change the display using Display settings
(page 11).
2
If you connect an optional CD changer with the CD-
*
TEXT function, the CD-TEXT information will appear
on the display when you playback a CD-TEXT disc.
The display item will change depending on the setting
as follows.
Type of
Priority display
disc
setting
D.MEMO
A
CD-TEXT
D.MEMO
B
CD-TEXT
D.MEMO
C
CD-TEXT
D.MEMO
D
CD-TEXT
$
$
$
Track name*
$
Clock
Disc memo
CD-TEXT information
Disc memo
CD-TEXT information
NO D.Name
1
2
Actual display
A: CD-TEXT disc with disc memo
B: Normal CD with disc memo
C: CD-TEXT disc without disc memo
D: Normal CD without disc memo
Erasing the disc memo
1 Press (SOURCE) repeatedly to select the
CD.
2 Press (MODE) repeatedly to select the CD
changer.
3 Press (LIST) for two seconds.
4 Press (DSPL) for two seconds.
5 Rotate the dial to select the name you
want to erase.
6 Press (5) (ENTER) for two seconds.
The name is erased.
Repeat steps 5 and 6 if you want to erase
other names.
7 Press (LIST) for two seconds.
The unit returns to the normal CD playback
mode.
Locating a disc by name
— List-up (CD changer with custom file
function or MD changer)
You can use this function for the discs that
have been assigned a custom name. For more
information on disc names, refer to “Labeling a
CD.”
1 Press (LIST) momentarily.
The name assigned to the disc currently
playing appears in the display.
LST
If you add disc memo labels to a CD-TEXT
disc, the display setting you make will
determine which information is displayed.
If the disc has only one set of information
(either CD-TEXT or disc memo labels ), that
information will be displayed regardless of
the display setting you make.
2 Press (LIST) repeatedly until you find the
desired disc.
DISC
EQSUR
1 SCHUBERT
ENTER
Bank edit mode.
CD2
Note
If you have not labeled the disc, the bank edit mode
does not appear and the programme edit mode appears.
To go back to the normal playback mode, press
(SHIFT).
EQSUR
DISCTRACK
5 1 Play
PLAY MODEENTER
2 Press either side of (SEEK/AMS) to select
the track number you want to skip and
press (5) (ENTER).
EQSUR
DISCTRACK
5 3 Skip
PLAY MODEENTER
CD2
The indication changes from “Play” to
“Skip.” If you want to return to “Play,”
press (5) (ENTER) again.
3 Repeat step 2 to set the “Play” or “Skip”
mode on all the tracks.
4 Press (3) (PLAY MODE) for two seconds.
The unit returns to the normal CD playback
mode.
EN
CD/MD Changer
3 Press (5) (ENTER) to play back the disc.
Notes
• Once a disc name has been displayed for five seconds, the
display goes back to its normal playback mode. To turn
off the display, press (DSPL).
• The track name are not displayed during MD playback.
• If there are no discs in the magazine, “NO Disc”
appears in the display.
• If a disc has not been assigned a custom file, “********”
appears in the display.
• If the disc information has not been read by the unit, “?”
appears in the display. To load the disc, first press the
number button, then choose the disc that has not been
loaded.
• The information appears only in upper cases. There are
also some letters which cannot be displayed (during MD
playback).
Selecting the specific
tracks for playback
— Bank (CD changer with custom file
function)
If you label the disc, you can set the unit to
skip tracks and play only the tracks you want.
1 Start playing the disc and press (SHIFT).
Then press (3) (PLAY MODE) for two
seconds.
5 Press (SHIFT).
Notes
• You can set the “Play” and “Skip” mode on up to 24
tracks.
• You cannot set the “Skip” mode on all the tracks.
Playing the specific tracks only
You can select:
•Back on to play the tracks with the “Play”
setting.
•Bank inv (Inverse) to play the tracks with the
“Skip” setting.
1 During playback, press (SHIFT), then
press (3) (PLAY MODE) repeatedly until
“Bank” appears.
2 Press (4) (n) to repeatedly until the
desired setting appears.
z Bank on z Bank inv z Bank off
BANK
CD1
EQSUR
Bank on
PLAY MODE
Playback starts from the track following the
current one.
3 Press (SHIFT).
To go back to the normal playing mode, select
“Bank off“ in step 2 above.
15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.