INSTALLATION AND MAINTENANCE MANUAL
1st Edition (Revised 7)
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
For HDC-900/910/930/950For HDC-900/910/930/950
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
For HDC-900/910/930/950
Laser Diode Properties
Material: In GaAsp
Wave length: 1310 nm
Emission duration: Pulse code modulation
Laser output power : _8 dBm
HDC-900 (SY)Serial No. 10001 and Higher
HDC-900/L (J)Serial No. 30001 and Higher
HDC-910 (UCJ)Serial No. 10001 and Higher
HDC-910/L (J)Serial No. 30001 and Higher
HDC-910 (CE)Serial No. 40001 and Higher
CLASS 1
LASER PRODUCT
LASER KLASSE 1
PRODUKT
This HD color camera is classified as a CLASS 1
LASER PRODUCT.
The CLASS 1 LASER PRODUCT label is located on the
cabinet near the CCU connector.
HDC-930 (SY)Serial No. 10001 and Higher
HDC-950 (JN, SY) Serial No. 10001 and Higher
HKC-T950 (SY)Serial No. 10001 and Higher
HDC-900/950 IMM
For HDC-900/910/930/950
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ . Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
HDC-900/950 IMM
1 (P)
For the customers in the Netherlands
Voor de klanten in Nederland
Hoe u de batterijen moet verwijderen, leest u in de
Onderhoudshandleiding.
Gooi de batterij niet weg maar lever deze in als klein
chemisch afval (KCA).
Für Kunden in Deutschland
Entsorgungshinweis: Bitte werfen Sie nur entladene
Batterien in die Sammelboxen beim Handel oder den
Kommunen. Entladen sind Batterien in der Regel dann,
wenn das Gerät abschaltet und signalisiert “Batterie
leer” oder nach längerer Gebrauchsdauer der Batterien
“nicht mehr einwandfrei funktioniert”. Um
sicherzugehen, kleben Sie die Batteriepole z.B. mit
einem Klebestreifen ab oder geben Sie die Batterien
einzeln in einen Plastikbeutel.
For the customers in Japan
For the customers in the U.S.A. and Canada
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable.
You can help preserve our environment
by returning your used rechargeable
batteries to the collection and recycling
location nearest you.
For more information regarding recycling of rechargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking Lithium-Ion
batteries.
2 (P)
HDC-900/950 IMM
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
This manual is the installation and maintenance manual of HD Color Camera HDC900/910/950/930 and HD CCD Block Adaptor HKC-T950 for HDC-950/930.
This manual is intended for use by trained system and service engineers, and is
provided information required for the installation and maintenance information .
Besides this installation and maintenance manual, the following manuals are available.
..
. HDC-900/910 Operation Manual (Supplied with HDC-900/910)
..
This manual is necessary for the use and the operation of the HDC-900/910.
Part No. : 3-204-021-XX
..
. HDC-950/930 Operation Manual (Supplied with HDC-950/930)
..
This manual is necessary for the use and the operation of the HDC-950/930.
Part No. : 3-204-027-XX
..
. HKC-T950 Operation Manual (Supplied with HKC-T950)
..
This manual is necessary for the installation and operation of the HKC-T950.
Part No. : 3-206-420-XX
..
. Maintenance Manual (Available on request)
..
This manual is intended for use by trained system and service engineers, and
describes the information regarding the circuit description, replacement of main
parts, SERVICE menu and electrical alignment.
For obtaining, contact your local Sony Sales Office/Service Center.
Part No. : 9-968-560-XX
..
. e-manual (Tentative name) (Available on request)
..
This electronic manual intended for use by trained system and service engineers
describes (detailed parts list, block diagrams, schematic diagrams, and board
layouts.) required for parts-level service.
For obtaining, contact your local Sony Sales Office/Service Center.
..
. System Manual (Available on request)
..
This manual is necessary for connection and operation of this unit and other
peripheral equipment.
If this manual is required, please contact to your local Sony Sales Office/Service
Center.
HDC-900/950 IMM
3 (E)
Contents
..
. “Semiconductor Pin Assignments” CD-ROM (Available on request)
..
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in B&P Company equipment.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
maintenance manual for the corresponding unit. The maintenance manual contains
a complete list of all semiconductors and their ID Nos., and thus should be used
together with the CD-ROM.
Part number: 9-968-546-XX
The installation and maintenance manual is organized by following sections.
Section 1Installation Overview
This section is described about the information that is required to install (switch
setting on the board, connection information, and the like.) and when installing this
unit.
Section 2Service Overview
This section is described about the recommended replacing parts, replacing the fuse
and the cleaning procedures.
Section 3Setup Menu
This section is described about the setup menu (TOP menu, OPERATION menu,
PAINT menu, MAINTENANCE menu, FILE menu and DIAGNOSIS menu).
Section 4File System
This section is described about the file system to control data.
4 (E)
HDC-900/950 IMM
Section 1
Installation Overview
1-1.Checking before Installation
1-1-1. Checking the ROM and Software Version
When connecting the peripheral equipment in the list below to HDC-900/910/950/
930, be sure to check that the ROM and software version on each peripheral device
is corresponding to the camera to be connected.
When the HKC-T950 is used by connecting into the HDC-950/930, be sure to check
the version of ROM of HDC-950/930.
If the ROM and software version is lower than the specified below, be sure to
perform ROM replacement and updating the software.
If ROM replacement and updating the software are required, contact your local Sony
Sales Office/Service Center.
ROM
Peripheral equipmentBoard nameRef No.Rom version
MSU-700A/750CPU-293/CPU-286IC5, IC6/IC5, IC6Ver. 1.10 or higher
CNU-700AT-89 or AT-89AIC4, IC5Ver. 3.20 or higher
CNU-500AT-100IC4, IC5Ver. 2.80 or higher
RCP-720/721MPU-79IC10Ver. 2.73 or higher
RCP-730/731MPU-79IC10Ver. 2.73 or higher
RCP-740/741MPU-79IC10Ver. 2.73 or higher
RCP-700/701MPU-92IC6Ver. 2.73 or higher
RM-B150CPU-266IC4Ver. 1.00 or higher
HDC-950AT-130IC1Ver. 1.20 or higher
HDC-930AT-130IC1Ver. 1.21 or higher
HDCU-900AT-141IC105, IC106Ver. 1.21 or higher
HDCU-950AT-149IC206Ver. 1.00 or higher
Software
Peripheral equipmentBoard nameSoftware version
RCP-750/751MPU-123Ver. 1.01 or higher
RM-B750MPU-124Ver. 1.00 or higher
1-1-2. Setting the Format of HDCU (HDC-910/930)
When setting the format of HDCU-900/950 in the system using the HDC-910/930,
be sure to select the format corresponding to the HDC-910/930.
HDC-900/950 IMM
1-1 (E)
1-2. Connectors and Cables
1-2.Connectors and Cables
1-2-1. Connector Input/Output Signals
HDC-900/910 Connector Layout
1
1
1
!\!/6 4 3 9 !, 7 8
1
5!] ![
!=1
!-!-
!;
1-2 (E)
HDC-900/950 IMM
HDC-950/930 Connector Layout
!.
1-2. Connectors and Cables
!-
1
2
*
4
!,
7
9
!'
![
!/
!] 5
!;
8
* : Use 4 connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch.
PROMPTER OUT signal become effective when the camera is connected to CCU.
GENLOCK IN and RET IN signals become effective when the camera is used alone.
36!\
HKC-T950 Connector Layout
@-
@[
@-
@=
@=
@\
@]
@/
!\
HDC-900/950 IMM
@[
1-3 (E)
1-2. Connectors and Cables
Input/Output Signals
11
1 CCU connector
11
Based upon BTA S-004A/005A/006A 1.485 Gbps
serial
Output Signals
22
2 EARPHONE OUT (HDC-950/930)
22
EARPHONE mini jack
33
3 TEST OUT
33
BNC type 75 Z, 1.0 V p-p
**
*
44
4 PROMPTER OUT
44
**
BNC type 75 Z, 1.0 V p-p
55
5 HD SERIAL DIGITAL OUT
55
Based upon BTA-S004A
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
@/@/
@/ VIDEO OUT (HKC-T950)
@/@/
BNC type 75 Z, 1.0 V p-p
77
7 RET CONTROL (6P FEMALE)
77
(External view)
No. SignalI/OSpecifications
1INCOM 1INZi > 10 kZ
MIC ON/OFFON : GND
OFF : OPEN
2INCOM 2INZi > 10 kZ
MIC ON/OFFON : GND
OFF : OPEN
3GND——
4NCNo connection
5RET 1 ON/OFFINZi > 10 kZ
ON : GND
OFF : OPEN
6RET 2 ON/OFFINZi > 10 kZ
ON : GND
OFF : OPEN
Input Signals
**
*
44
4 GENLOCK IN
44
**
(HDC-950/930)
BNC type 75 Z, 1.0 V p-p
**
*
44
4 RET IN
44
**
(HDC-950/930)
BNC type 75 Z, 1.0 V p-p
66
6 Not used
66
* : Use this connector by selecting PROMPTER OUT, GENLOCK IN and
RET IN signals with the switch on the rear panel of HDC-950/930.
PROMPTER OUT signal become effective when the camera is
connected to CCU.
GENLOCK IN and RET IN signals become effective when the camera is
used alone.
88
8 DC OUT (4P FEMALE)
88
1
4
23
(External view)
No. SignalI/OSpecifications
1GND——GND for POWER
2NCNo connection
3NCNo connection
4UNREGOUT+12 V dc 500 mA (max)
1-4 (E)
HDC-900/950 IMM
1-2. Connectors and Cables
99
9 REMOTE (8P FEMALE)
99
(External view)
No. SignalI/OSpecifications
1TX (+)HDC SERIAL DATA
2TX (_)
3RX (+)HDCU/MSU/RCP/CNU/VCS
4RX (_)SERIAL DATA
5TX GND——GND for TX
6POWER (+)OUT+26 V, 200 mA (max)
7POWER GND——GND for POWER (+)
8VIDEO (X)75 Z, 1.0 V p-p
CHASSIS GND——CHASSIS GND
!/!/
!/ AUDIO IN CH1/CH2 (3P FEMALE)
!/!/
!-!-
!- INTERCOM CH1/CH2 (5P FEMALE)
!-!-
(External view)
No. SignalI/OSpecifications
1INCOM MIC (Y)IN_20 dBu (CARBON MIC)
2INCOM MIC (X)IN_60 dBu (DYNAMIC MIC)
3
EGND——CHASSIS GND
NUTL (C)OUTAC 100 V, 200 V or below
LUTL (H)OUT
![![
![ DC IN (4P MALE)
![![
No. SignalI/OSpecifications
1GND——GND for DC (+)
2NCNo connection
3NCNo connection
4DC (+)IN+10.5 to 17 V dc
N
(External view)
(External view)
E
HDC-900/950 IMM
1-5 (E)
1-2. Connectors and Cables
!]!]
!] VTR (26P MALE) (HDC-900/910)
!]!]
B
6
5
A
4
11
3
10
2
1
7
12
17
9
16
8
15
22
14
21
13
20
19
24
18
23
(External view)
No. SignalI/OSpecifications
ANCNo connection
BVTR CMD GND——GND for VTR CMD
1GENLOCKINSync 0.6 V p-p, 0 V dc,
Zi = 75 Z
2GENLOCK GND——GND for GENLOCK
3G/Y GND——GND for G/Y
4G/YOUT1 Vp-p, 0 V dc, Zo = 75 Z
5R/PROUT1 Vp-p/±0.35 V p-p, 0 V dc,
Zo = 75 Z
6R/PR GND——GND for R/PR
7B/PBOUT1 Vp-p/±0.35 V p-p, 0 V dc,
Zo = 75 Z
8B/PB GND——GND for B/PB
9CH1 MIC (X)OUT_20 dBu, Low impedance,
10 CH1 MIC (Y)OUTBalanced
11 CH1/CH2 MIC GND ——GND for CH1/CH2 MIC
12 NCNo connection
13 NCNo connection
14 INCOM LINEIN/OUT 0.5 V p-p
15 CH2 MIC (X)OUT_20 dBu, Low impedance,
16 CH2 MIC (Y)OUTBalanced
17 NCNo connection
18 RET VIDEOIN1.0 V p-p, 0 V dc,
Zi = 75 Z
19 RET VIDEO GND——GND for RET VIDEO
20 AUDIOIN_6 dBu, 750 Z/1 kHz
21 RX COMMAND (X) INRS-422
22 RX COMMAND (Y) IN
23 TX COMMAND (X) OUTRS-422
24 TX COMMAND (Y) OUT
(0 dBu = 0.775 Vrms)
!]!]
!] VTR (26P MALE) (HDC-950/930)
!]!]
B
6
5
A
4
11
3
10
2
1
7
12
17
9
16
8
15
22
14
21
13
20
19
24
18
23
(External view)
No. SignalI/OSpecifications
AVTR UNREGIN+10.5 to 17 V dc
BUNREG GND——GND for UNREG
1GENLOCKINSync 0.6 V p-p, 0 V dc,
Zi = 75 Z
2GENLOCK GND——GND for GENLOCK
3G/Y GND——GND for G/Y
4G/YOUT1 V p-p, 0 Vdc, Zo = 75 Z
5R/PROUT1 V p-p/±0.35 V p-p, 0 V dc,
Zo = 75 Z
6R/PR GND——GND for R/PR
7B/PBOUT1 V p-p/±0.35 V p-p, 0 V dc,
Zo = 75 Z
8B/PB GND——GND for B/PB
9CH1 MIC (X)OUT_20 dBu, Low impedance
10 CH1 MIC (Y)OUTBalanced
11 CH1/CH2 MIC GND ——GND for CH1/CH2 MIC
12 UNREG (+) SENSE IN
13 UNREG (_) SENSE IN
14 INCOM LINEIN/OUT 0.5 V p-p
15 CH2 MIC (X)OUT_20 dBu, Low impedance,
16 CH2 MIC (Y)OUTBalanced
17 NCNo connection
18 RET VIDEOIN1.0 V p-p, 0 V dc,
Zi = 75 Z
19 RET VIDEO GND——GND for RET VIDEO
20 AUDIOIN_6 dBu, 750 Z/1 kHz
21 RX COMMAND (X) INRS-422
22 RX COMMAND (Y) IN
23 TX COMMAND (X) OUTRS-422
24 TX COMMAND (Y) OUT
(0 dBu = 0.775 Vrms)
1-6 (E)
HDC-900/950 IMM
!\!\
!\ LENS (36P FEMALE) (HDC-900/910)
!\!\
1-2. Connectors and Cables
18
36
No. SignalI/OSpecifications
1NCNo connection
2COMMON 5 VINNo connection
3NCNo connection
4+12 V (LENS)OUT+12 V (at 2 A)
5LENS DC GND——GND for +12 V (LENS)
6GND (SIG)——GND
7NCNo connection
8LENS EXT-1IN
9LENS EXT-2IN
10 LENS EXT-3IN
*
2
*
2
*
2
11 NC LENS AUXOUTON : GND
OFF : High impedance
12 IRIS POSIINZi > 10 kZ
2 to 7 V
“3.4 ± 0.1 V (F16)”
“6.2 ± 0.1 V (F2.8)”
13 ZOOM POSIINZi > 10 kZ
2 to 7 V
“2 V (WIDE), 7 V (TELE)”
14 RET 1 ONINZi > 10 kZ
ON : GND
OFF : High impedance
15 RET 2 ONINZi > 10 kZ
ON : GND
OFF : High impedance
16 FOCUS POSIINZi > 10 kZ
2 to 7 V
“2 V (MIN), 7 V (∞)”
17 IRIS CONT SIGOUT2 to 7 V
“3.4 ±0.1 V (F16)”
“6.2 ±0.1 V (F2.8)”
Zo < 1 kZ
18 IRIS AUTOOUTAUTO : GND
/MANUMANU : High impedance
Zo < 1 kZ
19 NCNo connection
20 NCNo connection
21 LENS R TALLYOUTON : GND
/STOPDISABLE : +5 V or OPEN
3GND——GND for UNREG
4AUTO SERVOOUTAUTO : +5 V
5IRIS CONTOUT+3.4 V (F16) to
6UNREGOUT+10.5 V to +17 V
7IRIS POSITIONIN+3.4 V (F16) to
8AUTO/MANUOUTAUTO IRIS : 0 V
9EXTENDERINEX 2 ON : GND
ON/OFFEX 0.8 ON : 30 kZ to GND
10 ZOOMINWIDE : 2 V
POSITIONTELE : 7 V
11 FOCUS POSIIN∞ : 7 V
(/LENS RX)min. : 2 V
12 (LENS TX)OUT
MANU : 0 V or OPEN
+6.2 V (F2.8)
+6.2 V (F2.8)
MANUAL IRIS : +5 V
OFF : OPEN
EX 2 ON
EX 0.8 ON
30 kΩ
!;!;
!; VF (25P FEMALE) (HDC-900/910)
!;!;
13123456789101112
25
(External view)
No. SignalI/OSpecifications
1Y VIDEO (X)OUT1.0 V p-p, Zo = 75 Z
2PR VIDEO GND——GND for PR VIDEO
3PR VIDEO (X)OUT0.7 V p-p, Zo = 75 Z
4PB VIDEO GND——GND for PB VIDEO
5PB VIDEO (X)OUT0.7 V p-p, Zo = 75 Z
6PEAKINGIN0 to 5 V dc
LEVEL
7+12 VOUT+10.5 to +20 V
8+12 V
9NCNo connection
10 S-DATAIN/OUTTTL level
11 R TALLYOUTON : +5 V
12 EFFECTOUTON : +5 V
13 NCNo connection
14 Y VIDEO GND——GND for Y VIDEO
15 S-CKOUTTTL level
16 BATT INDOUTON : +5 V
17 CHASSIS GND——
18 G TALLYOUTON : +5 V
19 GND (+12 V)——GND for +12 V
20 GND (+12 V)
21 VF-SELINBW : 0 V
OFF : GND
9NCNo connection
10 NCNo connection
11 NCNo connection
12 Y VIDEOOUT1.0 V p-p, Zo = 75 Z
13 VIDEO GND——GND for VIDEO
14 Pb VIDEOOUT±0.35 V p-p, Zo = 75 Z
15 Pr VIDEOOUT±0.35 V p-p, Zo = 75 Z
16 NCNo connection
17 R TALLYOUTON : 5 V
OFF : GND
18 NCNo connection
19 UNREG GND——GND for UNREG
20 UNREGOUT+10.5 V to +17 V
!'!'
!' EXT I/O (20P) (HDC-950/930)
!'!'
11
5
17
18
19
20
1
2
3
4
10
16
(External view)
No. SignalI/OSpecifications
1Y VIDEO (X)OUT1.0 V p-p, Zo = 75 Z
2Y VIDEO (G)——GND for Y VIDEO
3PROMPTER (X)OUT1.0 V p-p, Zo = 75 Z
4PROMPTER (G)——GND for PROMPTER
5Pr VIDEO (X)OUT±0.35 V p-p, Zo = 75 Z
6Pr VIDEO (G)——GND for Pr VIDEO
7Pb VIDEO (X)OUT±0.35 V p-p, Zo = 75 Z
8Pb VIDEO (G)——GND for Pb VIDEO
9SDA VFIN/OUTTTL level
10 VDOUTNegative Pulse,
3.0 V p-p, Low impedance
11 CALL ONINON : L (0 v)
OFF : H (+3 V)
12 VF POWER OFFOUTON : H (+5 V)
OFF : L (0 V)
13 MAIN POWEROUTON : +8 V
ON/OFFOFF : GND
14 SCL VFOUTTTL level
15 TALLY GND——GND for TALLY
16 BACK TALLYOUTON : 5 V
OFF : GND
17 PANEL DATAINRX SERIAL DATA
18 PANEL DATAOUTTX SERIAL DATA
19 VF UNREG +OUT
+12 V (+10.5 V to +17.0 V)
20 GND——GND for UNREG
HDC-900/950 IMM
1-9 (E)
1-2. Connectors and Cables
!,!,
!, TRACKER (FEMALE)
!,!,
1
2
6
11
16
5
3
4
7
8139
12
10
14
15
17
182019
(External view)
No. SignalI/OSpecifications
1TRK R (X)OUTTRACKER RECEIVE
0 dBu unbalanced
2TRK R (G)——GND for TRACKER R
3GND——GND for UNREG/TALLY
(UNREG/TALLY)
4R TALLYOUTON : 5 V (Open Collector)
OFF : 0 V (Open Collector)
5TRK PGM (G)——GND for PGM
6UNREGOUT+12 V (+10.5 to +17.0 V)
7TRK T (X)INTRACKER TALK
8TRK T (Y)IN0 dBu /_20 dBu
High impedance balanced
9TRK T (G)——GND for TRACKER T
10 TRK PGM (X)OUT_20 dBu unbalanced
11 NCNo connection
12 G TALLYOUTON : 5 V (Open Collector)
OFF : 0 V (Open Collector)
13 NCNo connection
14 RX_DATA (0)INTRUNK DATA IN, RS232-C
15 RX_DATA (1)IN
16 NCNo connection
17 NCNo connection
18 TX_DATA (0)OUT
TRUNK DATA OUT, RS232-C
19 TX_DATA (1)OUT
20 GND——
(0 dBu = 0.775 Vrms)
!.!.
!. FRONT MIC (3P FEMALE) (HDC-950/930)
!.!.
21
3
(External view)
No. SignalI/OSpecifications
1CHU MIC (G)——_60 dBu, _50 dBu, _40 dBu,
2CHU MIC (X)IN_30 dBu, _20 dBu, selectable
3CHU MIC (Y)INHigh impedance, Balanced
MANU : 0 V or OPEN
5NCNo connection
6NCNo connection
7NCNo connection
8G TALLYOUTON : 5 V
OFF : GND
9NCNo connection
10 NCNo connection
11 NCNo connection
12 Y VIDEOOUT1.0 V p-p, Zo = 75 Z
13 VIDEO GND——GND for VIDEO
14 NCNo connection
15 NCNo connection
16 NCNo connection
17 R TALLYOUTON : 5 V
OFF : GND
18 NCNo connection
19 UNREG GND——GND for UNREG
20 UNREGOUT+10.5 V to +1.7 V
MANU : 0 V or OPEN
5NCNo connection
6NCNo connection
7NCNo connection
8G TALLYINON : 5 V
OFF : GND
9NCNo connection
10 NCNo connection
11 NCNo connection
12 Y VIDEOIN1.0 V p-p, Zi = 75 Z
13 VIDEO GND——GND for VIDEO
14 NCNo connection
15 NCNo connection
16 NCNo connection
17 R TALLYINON : 5 V
AUNREGIN13 V to 17 V
BUNREG GND——GND for UNREG
1OHB HOUT0.3 V p-p Positive pulse
2OHB H (G)——GND for OHB H
3G VIDEO (G)——GND for G VIDEO
4G VIDEO (X)OUT
5R VIDEO (X)OUT
6R VIDEO (G)——GND for R VIDEO
7B VIDEO (X)OUT95 mV p-p, Zo = 75 Z (100 %)
8B VIDEO (G)——GND for B VIDEO
9MIC (X)OUT_60 dBu, _50 dBu, _40 dBu,
10 MIC (Y)OUT_30 dBu, _20 dBu, selectable
11 INCOM/MIC GND——GND for INCOM/MIC,
12 IRIS CONTIN+3.4 V (F16) to +6.2 V (F2.8)
13 CHU FIN0.3 V p-p Positive pulse
14 INCOM RECEIVEIN0 dBu
15 INCOM MIC (X)OUT_20 dBu (CARBON MIC)
16 INCOM MIC (Y)OUT_60 dBu (DYNAMIC MIC)
17 CHU HIN150 mV p-p Positive pulse
18 VF VIDEO (X)IN180 mV p-p, Zi = 75 Z
19 VF VIDEO (G)——GND for VF VIDEO,CHU H
20 PGMIN0 dBu
21 RX COMMAND (X) IN
22 RX COMMAND (Y) IN340 mV p-p
23 TX COMMAND (X) OUT
24 TX COMMAND (Y) OUT
17
10
16
9
22
15
14
21
20
19
24
23
300 mV p-p, Zo = 75 Z (100 %)
300 mV p-p, Zo = 75 Z (100 %)
CHU F, IRIS CONT
@\@\
@\ OPT HEAD (HKC-T950)
@\@\
(26P FEMALE)
B
6
5
11
17
16
22
21
24
(External view)
No. SignalI/OSpecifications
AUNREGOUT13 V to 17 V
BUNREG GND——GND for UNREG
1OHB HIN0.3 V p-p Positive pulse
2OHB H (G)——GND for OHB H
3G VIDEO (G)——GND for G VIDEO
4G VIDEO (X)IN300 mV p-p, Zi = 75 Z (100 %)
5R VIDEO (X)IN300 mV p-p, Zi = 75 Z (100 %)
6R VIDEO (G)——GND for R VIDEO
7B VIDEO (X)IN95 mV p-p, Zi = 75 Z (100 %)
8B VIDEO (G)——GND for B VIDEO
9MIC (X)IN_60 dBu, _50 dBu, _40 dBu,
10 MIC (Y)IN_30 dBu, _20 dBu, selectable
11 INCOM/MIC GND——GND for INCOM/MIC,
12 IRIS CONTOUT+3.4 V (F16) to +6.2 V (F2.8)
13 CHU FOUT0.3 V p-p Positive pulse
14 INCOM RECEIVEOUT0 dBu
15 INCOM MIC (X)IN_20 dBu (CARBON MIC)
16 INCOM MIC (Y)IN_60 dBu (DYNAMIC MIC)
17 CHU HOUT150 mV p-p Positive pulse
18 VF VIDEO (X)OUT180 mV p-p, Zo = 75 Z
19 VF VIDEO (G)——GND for VF VIDEO, CHU H
20 PGMOUT0 dBu
21 RX COMMAND (X) OUT
22 RX COMMAND (Y) OUT340 mV p-p
23 TX COMMAND (X) IN
24 TX COMMAND (Y) IN
A
4
3
10
2
9
15
20
23
1
8
7
14
13
12
19
18
CHU F, IRIS CONT
1-12 (E)
HDC-900/950 IMM
1-2-2. Wiring Diagrams for Cables
CCA-5 Cable
1-2. Connectors and Cables
HDCZ Cable
Yellow
Black
Blue
Red
Brown
Gray
Red
Black
White
Red
Red
White
Blue
Red
White
Orange
White
Red
Yellow
White
HDC-900/950 IMM
1-13 (E)
1-2. Connectors and Cables
1-2-3. Connection Connectors/Cables
Connection made with the connector panels during installation or service, should be made with the connectors/
complete cable assemblies specified in the following list,
or equivalent parts.
IndicationConnection connector/cable
TEST OUT1-569-370-12 Plug, BNC
PROMPTER
SERIAL OUT
VIDEO OUT
(BNC)
AUDIO IN1-508-084-00 XLR, 3P Male or
MIC INITT Cannon XLR-3-12C equivalent
(3P FEMALE)Cable assembly
MIC IN1-508-083-00 XLR, 3P, Female or
(3P MALE)ITT Cannon XLR-3-11C equivalent
RET CONTROL1-560-078-00 Plug, 6P Male or
(6P FEMALE)HIROSE HR10-7PA-6P equivalent
DC OUT1-566-425-11 Plug, 4P Male or
(4P FEMALE)HIROSE HR10A-7P-4P equivalent
INTERCOM1-508-370-11 XLR, 5P Male or
INCOMITT Cannon XLR-5-12C equivalent
(5P FEMALE)Cable assembly
INCOM1-508-363-00 XLR, 5P Female or
(5P MALE)ITT Cannon XLR-5-11C equivalent
VTR1-564-184-00 Plug, 26P Female or
CAM BODYCable assembly
OPT HEAD1-564-183-31 Plug, 26P Male or
(26P FEMALE)Cable assembly
DC IN1-508-362-00 XLR, 4P Female or
(4P MALE)ITT Cannon XLR-4-11C equivalent, or
(supplied with HKC-T950, 0.8 m)
1-823-599-11
Cable assembly
(supplied with HKC-T950, 0.8 m)
1-823-599-11
(supplied with HKC-T950, 0.8 m)
1-823-600-11
Cable assembly
(supplied with HKC-T950, 0.8 m)
1-823-600-11
HDCZ-A10
(supplied with HKC-T950, 10 m)
1-823-615-11
HDCZ-A25 (option, 25 m)
1-823-616-11
HDCZ-A50 (option, 50 m)
1-823-617-11
HDCZ-A10
(supplied with HKC-T950, 10 m)
1-823-615-11
HDCZ-A25 (option, 25 m)
1-823-616-11
HDCZ-A50 (option, 50 m)
1-823-617-11
Cable assembly 1-551-577-00
(Supplied with AC-550/550CE)
*3
*3
*3
*3
*3
*3
IndicationConnection connector/cable
REMOTE1-766-848-11 Plug, 8P Male or
(8P FEMALE)CCA-5 cable assembly (option)
CCA-5-10 (10 m) /CCA-5-3 (3 m) or
REMOTE cable 1-783-372-11
(supplied with RM-B150, 10 m)
TRACKERHIROSE HR25-9P-20P equivalent
(20P FEMALE)
VFCable assembly
(20P FEMALE)(supplied with HKC-T950, 0.7 m)
1-792-603-21
*1: Use of REMOTE cable enables to monitor video signals.
*2: If using a cable of length different from a standard product, contact your
local Sony Sales Office/Service Center.
*3: Only for HKC-T950.
*2
*1 *2
1-2-4. Note in connecting CCU connector
It is recommendable to clean the optical contact portions
mentioned below before connecting this unit to the camera
control unit.
. CCU connector of this unit
. Camera connector of the camera control unit
. Optical/Electrical cable
It is also necessary to clean the optical contact portions
mentioned below before using the HDC-950/930 to the
large lens adaptor CA-905L.
. CA cable of a large lens adaptor
. CCU connector of a large lens adaptor
For details on a cleaning method, refer to Section 2-1
“Cleaning of Connector/Cable”.
1-14 (E)
HDC-900/950 IMM
1-3.Location of Printed Circuit Boards
HDC-900/910
1-3. Location of Printed Circuit Boards
CN-2073
SW-1019
CN-1702
CN-1974
SW-1020
CN-2016
PS-582
CN-1956
RX-28
AT-131
MB-883
CN-986
RE-184
RE-182
LE-172
RE-181
DU-104
AU-271
AT-130
SG-268
DAP-24
DAD-37
VDA-55
DPR-156
DPR-154
VA-196
SDI-49
IF-784
SW-1045
CN-2074
CN-1961
RP-114
DU-69
TG-214
BI-145
DR-412
SERVO DRIVER
NR-69/73
PA-239
CN-2015
CN-1947
BI-145
CN-1998
CN-1961
CN-2017
RP-114
DU-69
TG-214
BI-150
DR-492
SERVO DRIVER
CN-2329
BI-150
NR-73
PA-239
HDC-900/950 IMM
HDC-900HDC-910
1-15 (E)
1-3. Location of Printed Circuit Boards
HDC-950/930
DPR-156
CN-2018
SW-1018
CN-1954
CN-1953
LP-113
RE-188
CN-1952
DU-104
RE-182
RE-184
CN-1702B
CN-2094
SW-1016
MB-882
CN-2026
SW-1029
BI-145
RX-28
DU-69
SW-1013
PA-239
NR-69/73
TG-214
SW-1015
RP-114
DR-412
SERVO DRIVER
SDI-49
SW-1014
VA-196
CN-1964
VDA-55
DPR-154
BI-150
DAP-24
DAD-37
DU-69
AT-130
SG-268
PA-239
AU-271
NR-69/73
TG-214
CN-1702B
SW-1017
SW-1027
CN-1951
CN-2063
CN-1955
RE-181
RP-114
DR-492
SERVO DRIVER
1-16 (E)
BI-145
HDC-950
CN-1947
CN-1961
BI-150
CN-1961
CN-2329
HDC-930
HDC-900/950 IMM
HKC-T950
1-3. Location of Printed Circuit Boards
LE-256CN-2270
AT-146
IF-845
SW-1065SW-1066
CN-2271
RE-202
CN-2202
SW-1076
CN-2264
AT-147
CN-2203
IF-846
CN-2265
HDC-900/950 IMM
1-17 (E)
1-4. Opening/Closing the Side Panel
1-4.Opening/Closing the Side Panel
HDC-900/910
1. Unscrew the two lock screws of the side panel.
2. While sliding the safety lock toward the lens, open the
side panel by holding the handle.
3. Close the side panel and tighten securely the lock
screws of the side panel.
[Reference][Reference]
[Reference]
[Reference][Reference]
Closing the side panel brings the safety lock to an
automatic locking.
Safety lock
Handle
Lock screw of the
side panel
HDC-950/930
1. Unscrew the eight screws as shown in the figure, then
remove the inside panel and outside panel.
2. Reinstall in the reverse order of removal step 1.
Outside panel
Screws
Inside panel
Screws
1-18 (E)
HDC-900/950 IMM
S104
S103
S1
S101
AU-271 board (A side)
S102
S201
S2
S202
S301
S304
S203
S204
S303
B
C
D
E
F
G
A
54 3 2 1
AU
CM
DYN
INCOM 1
INCOM 1 switch
INCOM 1 MIC GAIN switch
MIC GAIN
DYN
INCOM 2
MIC GAIN
MIC
MONITOR
ON
+
0
_
+
0
_
OFF
INCOM 2 switch
INCOM 2 MIC GAIN switch
MIC MONITOR switch
AU-271 board suffix -13 and higher
(B side)
S300
1
A
B
C
D
E
F
G
2345
1-5.Switch Setting on the Boards
AU-271 board
1-5. Switch Setting on the Boards
Ref. No.NameContentsFactory Setting
S1-1
S1-2
S2-1
S2-2PGM2 INCOM2 RECEIVESwitch ON to mix the PGM2 signal adjusted the sound volumeOFF
S101-1PGM1 MUTE ON/OFFSwitch OFF to output the PGM1 signal to the PGM OUT of theOFF
S101-2PGM2 MUTE ON/OFFSwitch OFF to output the PGM2 signal to the PGM OUT of theON
S101-3INCOM1 MUTE ON/OFFSwitch OFF to output the INCOM1 RECEIVE signal to the PGM OUTOFF
S101-4INCOM2 MUTE ON/OFFSwitch OFF to output the INCOM2 RECEIVE signal to the PGM OUTON
S102-1PGM1 MUTE ON/OFFSwitch OFF to output the PGM1 signal to the INCOM OUT ofOFF
S102-2PGM2 MUTE ON/OFFSwitch OFF to output the PGM2 signal to the INCOM OUT ofON
S102-3INCOM1 MUTE ON/OFFSwitch OFF to output the INCOM1 RECEIVE signal to the INCOMOFF
S102-4INCOM2 MUTE ON/OFFSwitch OFF to output the INCOM2 RECEIVE signal to the INCOMON
HDC-900/950 IMM
*1
TRACKER INCOM2 ON/OFF Switch ON to mix the TRACKER TALK signal of the TrackerOFF
connector to CCU INCOM2 RECEIVE OUT.
*2
*2
Not used————
PGM1 INCOM1 RECEIVESwitch ON to mix the PGM1 signal adjusted the sound volume byOFF
MIX ON/OFFthe PGM volume control to the INCOM1 RECEIVE signal before
the sound volume adjustment.
MIX ON/OFFby the PGM volume control to the INCOM2 RECEIVE signal before
the sound volume adjustment.
INTERCOM1 connector.
INTERCOM1 connector.
of the INTERCOM1 connector.
of the INTERCOM1 connector.
the INTERCOM1 connector.
the INTERCOM1 connector.
OUT of the INTERCOM1 connector.
OUT of the INTERCOM1 connector.
1-19 (E)
1-5. Switch Setting on the Boards
Ref. No.NameContentsFactory Setting
S103INCOM1 MIC GAIN +/0/_Select the audio level of INTERCOM1/2 to be sent to CCU.0
+ :+6dB
0 : 0dB
_ :_6dB
S104INCOM1 MIC TYPESelect from two options below in accordance with the microphoneCM
of the head set connected to the INTERCOM1/2 connector.
CM : Carbon microphone
DYN :Dynamic microphone
S201-1PGM1 MUTE ON/OFFSwitch OFF to output the PGM1 signal to the PGM OUT of theON
INTERCOM2 connector.
S201-2PGM2 MUTE ON/OFFSwitch OFF to output the PGM2 signal to the PGM OUT ofOFF
the INTERCOM2 connector.
S201-3INCOM1 MUTE ON/OFFSwitch OFF to output the INCOM1 RECEIVE signal to the PGMON
OUT of the INTERCOM2 connector.
S201-4INCOM2 MUTE ON/OFFSwitch OFF to output the INCOM2 RECEIVE signal to the PGMOFF
OUT of the INTERCOM2 connector.
S202-1PGM1 MUTE ON/OFFSwitch OFF to output the PGM1 signal to the INCOM OUT of theON
INTERCOM2 connector.
S202-2PGM2 MUTE ON/OFFSwitch OFF to output the PGM2 signal to the INCOM OUT of theOFF
INTERCOM2 connector.
S202-3INCOM1 MUTE ON/OFFSwitch OFF to output the INCOM1 RECEIVE signal to the INCOMON
OUT of the INTERCOM2 connector.
S202-4INCOM2 MUTE ON/OFFSwitch OFF to output the INCOM2 RECEIVE signal to the INCOMOFF
OUT of the INTERCOM2 connector.
S203INCOM2 MIC GAIN +/0/_Select the audio level of the INTERCOM1/2 to be sent to CCU.0
+ :+6dB
0 : 0dB
_ :_6dB
S204INCOM2 MIC TYPESelect from two options below in accordance with the microphone ofCM
the head set connected to the INTERCOM 1/2 connector.
CM : Carbon microphone
DYN :Dynamic microphone
*3
S300-1
AUDIO1 +12 V OFF/ONSwitch ON to supply +12 V for MIC POWER to the microphoneOFF
connected the AUDIO IN 1 connector.
*3
S300-2
AUDIO2 +12 V OFF/ONSwitch ON to supply +12 V for MIC POWER to the microphoneOFF
connected the AUDIO IN 2 connector.
S301-1TRACKER RECEIVE OUTSwitch ON to mix the PGM1 signal to the TRACKER RECEIVE OUTOFF
PGM1 MIXof the TRACKER connector.
S301-2TRACKER RECEIVE OUTSwitch ON to mix the PGM2 signal to the TRACKER RECEIVE OUTOFF
PGM2 MIX of the TRACKER connector.
*1
S301-3
TRACKER RECEIVE OUTSwitch ON to mix the INCOM2 RECEIVED signal to the TRACKEROFF
IMCOM2 RECEIVE MIXRECEIVE OUT of the TRACKER connector.
*1
S301-4
TRACKER RECEIVE OUTSwitch ON to mix the INCOM2 TALK signal to the TRACKEROFF
INCOM2 TALK MIXRECIVE OUT of the TRACKER connector.
S303MIC MONITOR ON/OFFSwitch ON to monitor the microphone input signal at the INCOM OUT OFF
or EARPHONE OUT.
S304TRACKER (T) 0/_20Select the input level of the TRACKER Connector.0
0 :0dBu
_20 : _20dBu
(0dBu = 0.775 Vrms)
1-20 (E)
HDC-900/950 IMM
1-5. Switch Setting on the Boards
*1: The Tracker connector communicates to INCOM1 at the standard setting, yet it is communicable to INCOM2 by setting S1-1, S301-1
and S301-4
to ON.
*2: When setting S2-1 or S2-2 to ON, set bit1 and bit2 of S101, S102, S201 and S202 as shown below to prevent PGM1 and PGM2
signals from being mixed double.
S2-1S101, 102, 201, 202S2-2S101, 102, 201, 202
bit1bit12
ONONONON
INCOM1
PGM 1
PGM 2
PGM1/2 swiitch
(Panel)
INCOM2
PGM1/2 swiitch
(Panel)
bit1
bit2
bit3
bit4
bit1
bit2
bit3
bit4
S101
S102
PGM OUT
INCOM OUT
INTERECOM CH1
INTERECOM CH1
CCU
S2-1
INCOM1
S2-2
INCOM2
bit1
bit2
bit3
bit4
bit1
bit2
bit3
bit4
S201
S202
PGM OUT
INCOM OUT
INTERECOM CH2
INTERECOM CH2
n
Each bit of S101, S102, S103 and S104 is opened when it is set to “ON” position.
Set to “OFF”position to close the switch.
*3: AU-271 board suffix -13 and higher.
HDC-900/950 IMM
1-21 (E)
Loading...
+ 67 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.