Sony CDX-GT317EE User Manual

2-886-504-22 (1)

FM/MW/LW Compact Disc Player

Operating Instructions

Инструкция по эксплуатации

To cancel the demonstration (DEMO) display, see page 11.

Для отмены демонстрации на дисплее (режим DEMO) см. стр. 13

CDX-GT317EE

2006 Sony Corporation

For installation and connections, see the supplied installation/connections manual.

Warning if your car’s ignition has no ACC position

Be sure to set the Auto Off function (page 11). The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold (OFF) until the display disappears each time you turn the ignition off.

This label is located on the bottom of the chassis.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Applicable accessory: Remote commander

This symbol on the product or on its

Microsoft, Windows Media, and the Windows logo are trademarks or registered

trademarks of Microsoft Corporation in the United States and/or other countries.

Table of Contents

Welcome ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 4

Preparing the card remote commander . . . . . . . 4

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 5

Detaching the front panel . . . . . . . . . . . . . . . . . 5

Attaching the front panel . . . . . . . . . . . . . . . 5

Location of controls and basic operations

Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Card remote commander RM-X151 . . . . . . . 6

Display items . . . . . . . . . . . . . . . . . . . . . . . . 8

Repeat and shuffle play. . . . . . . . . . . . . . . . . 8

Radio

Storing and receiving stations . . . . . . . . . . . . . . 8

Storing automatically — BTM . . . . . . . . . . . 8

Storing manually. . . . . . . . . . . . . . . . . . . . . . 8

Receiving the stored stations . . . . . . . . . . . . 8

Tuning automatically . . . . . . . . . . . . . . . . . . 8

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting AF and TA . . . . . . . . . . . . . . . . . . . . 9

Selecting PTY. . . . . . . . . . . . . . . . . . . . . . . 10

Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . 10

Other functions

Changing the sound settings . . . . . . . . . . . . . . 11

Adjusting the sound characteristics

— BAL/FAD/SUB. . . . . . . . . . . . . . . . . . . 11

Customizing the equalizer curve

— EQ3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting setup items — SET . . . . . . . . . . . . 11

Using optional equipment. . . . . . . . . . . . . . . . 12

Auxiliary audio equipment. . . . . . . . . . . . . 12

CD/MD changer . . . . . . . . . . . . . . . . . . . . . 12

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Notes on discs . . . . . . . . . . . . . . . . . . . . . . 13

About MP3/WMA files . . . . . . . . . . . . . . . 14

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing the unit. . . . . . . . . . . . . . . . . . . . . . 15

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 17

Error displays/Messages. . . . . . . . . . . . . . . 18

Welcome !

Getting Started

Thank you for purchasing this Sony Compact Disc Player. You can enjoy your drive with the following functions.

• CD playback

You can play CD-DA (also containing CD TEXT*) and CD-R/CD-RW (MP3/WMA files also containing Multi Session (

Type of discs Label on the disc

CD-DA

MP3

WMA

• Radio reception

– You can store up to 6 stations per band (FM1,

FM2, FM3, MW and LW).

– BTM (Best Tuning Memory): The unit selects

strong signal stations and stores them.

• RDS services

– You can use FM station with Radio Data

System (RDS).

• Sound adjustment – EQ3 stage2: You can choose any one of 7

preset equalizer curves.

• Optional unit operation You can also control optional CD/MD changers.

• Auxiliary equipment connection An AUX input jack on the front of the unit allows connection of a portable audio device.

* A CD TEXT disc is a CD-DA that includes

information such as disc, artist and track name.

page 14)).

Resetting the unit

Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Detach the front panel and press the RESET button with a pointed object, such as a ball-point pen.

RESET button

Note

Pressing the RESET button will erase the clock setting and some stored contents.

Preparing the card remote commander

Before using the card remote commander for the first time, remove the insulation film.

Setting the clock

The clock uses a 24-hour digital indication.

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until “CLOCK-ADJ” appears.

3 Press (SEEK) +.

The hour indication flashes.

4 Rotate the volume control dial to set

the hour and minute.

To move the digital indication, press (SEEK) –/+.

5 Press the select button.

The setup is complete and the clock starts.

To display the clock, press (DSPL). Press (DSPL) again to return to the previous display.

With the card remote commander

In step 4, to set the hour and minute, press M or m.

Tip

You can set the clock automatically with the RDS feature (

page 10).

Detaching the front panel

You can detach the front panel of this unit to prevent theft.

Attaching the front panel

Engage part A of the front panel with part B of the unit, as illustrated, and push the left side into position until it clicks.

Note

Do not put anything on the inner surface of the front panel.

Caution alarm

If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used.

1 Press (OFF).

The unit is turned off.

2 Press , then pull it off towards you.

Notes

• Do not drop or put excessive pressure on the front

panel and display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray.

Location of controls and basic operations

1 2

4 5 8673

Main unit

OFF

PUSH SELECT

SOURCE

SEEK

EQ3

AUX

PTY

qa qdq;9 qs qfqg

Card remote commander RM-X151

1 4

OFF

SOURCE

SEL

–

DSPL

132

465

VOL

–

MODE

SCRL

ALBMDIM REP SHUF

123456

DSPL

PAUSE

AF/TA

CDX-GT317EE

qjqh

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those

ATT

w; wa

on the unit.

A OFF button

To power off; stop the source.

B EQ3 (equalizer) button 11

To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).

C Volume control dial/select button 11

To adjust volume (rotate); select setup items (press and rotate).

D SOURCE button

To power on; change the source (Radio/CD/

MD*

/AUX).

E Disc slot

Insert the disc (label side up), playback starts.

F Display window G AUX input jack 12

To connect a portable audio device.

H Z (eject) button

To eject the disc.

I PTY (Program Type) button 10

To select PTY in RDS.

J (front panel release) button 5

K SEEK –/+ buttons

CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold).

L Receptor for the card remote

commander

M MODE button 8, 12

To select the radio band (FM/MW/LW); select the unit*

N DSPL (display)/DIM (dimmer) button

8, 9

To change display items (press); change the display brightness (press and hold).

O RESET button (located behind the front

panel)

P Number buttons

CD/MD*1: (1)/(2): ALBM –/+*3*

To skip albums (press); skip albums continuously (press and hold).

(3): REP 8 (4): SHUF 8 (6): PAUSE*

To pause playback. To cancel, press

again. Radio: To receive stored stations (press); store stations (press and hold).

Q AF (Alternative Frequencies)/TA

(Traffic Announcement) button 9

To set AF and TA in RDS.

The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (

page 4).

qk < (.)/, (>) buttons

To control CD/radio, the same as (SEEK) –/+ on the unit.

ql VOL (volume) +/– button

To adjust volume.

w; ATT (attenuate) button

To attenuate the sound. To cancel, press again.

wa SEL (select) button

The same as the select button on the unit.

ws M (+)/m (–) buttons

To control CD, the same as (1)/(2) (ALBM –/+) on the unit.

wd SCRL (scroll) button 8

To scroll the display item.

wf Number buttons

To receive stored stations (press); store stations (press and hold).

*1 When an MD changer is connected. *2 When a CD/MD changer is connected. *3 When an MP3/WMA is played. *4 If the changer is connected, the operation is

different, see page 13.

*5 When playing back on this unit.

Note

If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

Tip

For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 15.

For details on selecting a CD/MD changer, see page 12.

Display items

A WMA/MP3 indication B Source C Track number/Elapsed playing time, Disc/

artist name, Album number* Track name, Text information*

*1 Album number is displayed only when the album is

changed.

*2 When playing an MP3, ID3 tag is displayed, and

when playing a WMA, WMA tag is displayed.

To change display items C, press (DSPL); scroll display items C, press (SCRL) on the card remote commander or set “A.SCRL-ON” (

page 12).

Tip

Displayed items will differ, depending on the disc type, recorded format and settings. For details on MP3/ WMA, see

page 14.

Repeat and shuffle play

1 During playback, press (3) (REP) or

(4) (SHUF) repeatedly until the desired setting appears.

Select To pl ay

TRACK track repeatedly.

ALBUM* album repeatedly.

SHUF ALBUM* album in random order.

SHUF DISC disc in random order.

* When an MP3/WMA is played.

To return to normal play mode, select “ OFF” or “SHUF OFF.”

, Album name,

, Clock

Radio

Storing and receiving stations

Caution

When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

1 Press (SOURCE) repeatedly until

“TUNER” appears.

To change the band, press (MODE) repeatedly. You can select from FM1, FM2, FM3*, MW or LW.

2 Press and hold the select button.

The setup display appears.

3 Press the select button repeatedly

until “BTM” appears.

4 Press (SEEK) +.

The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored.

* FM3 tuning range is 65 to 74 MHz (at 30KHz step).

Storing manually

1 While receiving the station that you

want to store, press and hold a number button ((1) to (6)) until “MEM” appears.

The number button indication appears in the display.

Note

If you try to store another station on the same number button, the previously stored station will be replaced.

Tip

When a RDS station is stored, the AF/TA setting is also stored (

Receiving the stored stations

1 Select the band, then press a number

Tuning automatically

1 Select the band, then press (SEEK) –/+

page 9).

button ((1) to (6)).

to search for the station.

Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received.

Tip

If you know the frequency of the station you want to listen to, press and hold (SEEK) approximate frequency, then press (SEEK) repeatedly to fine adjust to the desired frequency (manual tuning).

–/+ to locate the

–/+

Notes

• Depending on the country/region, not all RDS functions may be available.

• RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data.

RDS

Overview

FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio program signal.

Display items

A TA /T P* B Radio band, Function C Frequency*

*1 “TA” flashes during traffic information. “TP” lights

*2 While receiving the RDS station, “ *” is displayed

To change display items C, press (DSPL).

RDS services

This unit automatically provides RDS services as follows:

AF (Alternative Frequencies)

Selects and retunes the station with the strongest signal in a network. By using this function, you can continuously listen to the same program during a long-distance drive without having to retune the same station manually.

TA (Traffic Announcement)/TP (Traffic Program)

Provides current traffic information/programs. Any information/program received, will interrupt the currently selected source.

PTY (Program Types)

Displays the currently received program type. Also searches your selected program type.

CT (Clock Time)

The CT data from the RDS transmission sets the clock.

(Program service name), Preset

number, Clock, RDS data

up while such a station is received.

on the left of the frequency indication.

Setting AF and TA

1 Press (AF/TA) repeatedly until the

desired setting appears.

Select To

AF-ON activate AF and deactivate TA.

TA-ON activate TA and deactivate AF.

AF, TA-ON activate both AF and TA.

AF, TA-OFF deactivate both AF and TA.

Storing RDS stations with the AF and TA setting

You can preset RDS stations along with the AF/ TA setting. If you use the BTM function, only RDS stations are stored with the same AF/TA setting. If you preset manually, you can preset both RDS and non-RDS stations with the AF/TA setting for each.

1 Set AF/TA, then store the station with BTM or

manually.

Presetting the volume of traffic announcememnts

You can preset the volume level of the traffic announcements so as to not miss hearing them.

1 Rotate the volume control dial to adjust the

volume level.

2 Press and hold (AF/TA) until “TA” appears.

Receiving emergency announcements

With AF or TA on, the emergency announcements will automatically interrupt the currently selected source.

Staying with one regional program — REG

When the AF function is on: this unit’s factory setting restricts reception to a specific region, so you will not be switched to another regional station with a stronger frequency.

If you leave this regional program’s reception area, set “REG-OFF” in setup during FM reception (

page 12).

continue to next page t

Note

This function does not work in the UK and in some other areas.

Local Link function (UK only)

This function enables you to select other local stations in the area, even if they are not stored on your number buttons.

1 During FM reception, press a number button

((1) to (6)) on which a local station is stored.

2 Within 5 seconds, press again a number button

of the local station. Repeat this procedure until the local station is received.

Selecting PTY

1 Press (PTY) during FM reception.

The current program type name appears if the station is transmitting PTY data.

2 Press (PTY) repeatedly until the

desired program type appears.

3 Press (SEEK) –/+.

The unit starts to search for a station broadcasting the selected program type.

Type of programs

NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP ROCK

M (Rock Music), EASY M (Easy Listening), LIGHT CLASSICS (Classical), OTHER Music Type), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children’s Programs), SOCIAL RELIGION (Religion), PHONE TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION

Music), FOLK (Documentary)

Note

You cannot use this function in countr ies/regions where no PTY data is available.

M (National Music), OLDIES (Oldies

M (Folk Music), DOCUMENT

M (Popular Music),

M (Light Classical),

M (Other

A (Social Affairs),

IN (Phone In),

Setting CT

1 Set “CT-ON” in setup (page 11).

Notes

• The CT function may not work even though an RDS station is being received.

• There might be a difference between the time set by the CT function and the actual time.

Other functions

Changing the sound settings

Adjusting the sound characteristics — BAL/FAD/SUB

You can adjust the balance, fader, and subwoofer volume.

1 Press the select button repeatedly

until “BAL,” “FAD” or “SUB” appears.

The item changes as follows:

LOW*1 t MID*1 t HI*1 t BAL (left-right) t FA D (front-rear) t SUB (subwoofer volume)*

*1 When EQ3 is activated (page 11). *2 When the audio output is set to “SUB”

(page 11). “ATT” is displayed at the lowest setting, and can be adjusted up to 20 steps.

*3 When AUX source is activated (page 12).

2 Rotate the volume control dial to

adjust the selected item.

After 3 seconds, the setting is complete and the display returns to normal play/reception mode.

With the card remote commander

In step 2, to adjust the selected item, press <, M, , or m.

Customizing the equalizer curve — EQ3

“CUSTOM” of EQ3 allows you to make your own equalizer settings.

1 Select a source, then press (EQ3)

repeatedly to select “CUSTOM.”

2 Press the select button repeatedly

until “LOW,” “MID” or “HI” appears.

3 Rotate the volume control dial to

adjust the selected item.

The volume level is adjustable in 1 dB steps, from –10 dB to +10 dB.

Repeat steps 2 and 3 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold the select button before the setting is complete. After 3 seconds, the setting is complete and the display returns to normal play/reception mode.

Tip

Other equalizer types are also adjustable.

t AUX *

With the card remote commander

In step 3, to adjust the selected item, press <, M, , or m.

Adjusting setup items — SET

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until the desired item appears.

3 Rotate the volume control dial to

select the setting (example “ON” or “OFF”).

4 Press and hold the select button.

The setup is complete and the display returns to normal play/reception mode.

Note

Displayed items will differ, depending on the source and setting.

With the card remote commander

In step 3, to select the setting, press < or ,.

The following items can be set (follow the page reference for details): “z” indicates the default settings.

CLOCK-ADJ (Clock Adjust) (page 5) CT (Clock Time)

To set “CT-ON” or “CT-OFF” (z) (page 9, 10).

BEEP

To set “BEEP-ON” (z) or “BEEP-OFF.”

AUX-A*

A.OFF (Auto Off)

SUB/REAR*

DEMO*1

DIM (Dimmer)

(AUX Audio) To turn the AUX source display “AUX-A-ON” (

z) or “AUX-A-OFF” (page 12).

To shut off automatically after a desired time when the unit is turned off, – “A.OFF-NO” (

z), “A.OFF-30S (Seconds),”

“A.OFF-30M (Minutes)” or “A.OFF-60M (Minutes).”

To switch the audio output. – “SUB-OUT” (

z): to output to a subwoofer.

– “REAR-OUT”: to output to a power amplifier.

(Demonstration)

To set “DEMO-ON” (z) or “DEMO-OFF.”

To change the brightness of the display. – “DIM-ON”: to dim the display. – “DIM-OFF” (

z): to deactivate the dimmer.

continue to next page t

A.SCRL (Auto Scroll)

To scroll long displayed item automatically when the disc/album/track is changed. – “A.SCRL-ON” (

z): to scroll.

– “A.SCRL-OFF”: to not scroll.

LOCAL (Local Seek Mode)

– “LOCAL-ON” : to only tune into stations with

stronger signals.

– “LOCAL-OFF” (

MONO*

(Monaural Mode)

z): to tune normal reception.

To improve poor FM reception, select monaural reception mode. – “MONO-ON” : to hear stereo broadcast in

monaural.

– “MONO-OFF” (

z): to hear stereo broadcast in

stereo.

REG*2 (Regional)

To set “REG-ON” or “REG-OFF” (

(Low Pass Filter)

LPF*

z) (page 9).

To select the subwoofer cut-off frequency: “LPF OFF” (

z), “LPF125Hz” or “LPF 78Hz.”

BTM (page 8)

*1 When the unit is turned off. *2 When FM is received. *3 When the audio output is set to “SUB.”

Using optional equipment

Auxiliary audio equipment

By connecting an optional portable audio device to the AUX input jack (stereo mini jack) on the unit and then simply selecting the source, you can listen on your car speakers. The volume level is adjustable for any difference between the unit and the portable audio device. Follow the procedure below:

Connecting the portable audio device

1 Turn off the portable audio device. 2 Turn down the volume on the unit. 3 Connect to the unit.

AUX

Connecting cord*

(not supplied)

* Be sure to use a straight type plug.

Adjust the volume level

Be sure to adjust the volume for each connected audio device before playback.

1 Turn down the volume on the unit. 2 Press (SOURCE) repeatedly until “AUX”

appears. “AUX FRONT IN” appears.

3 Start playback of the portable audio device at a

moderate volume.

4 Set your usual listening volume on the unit. 5 Press the select button repeatedly until “AUX”

appears, and rotate the volume control dial to adjust the input level (–8 dB to +18 dB).

CD/MD changer

Selecting the changer

1 Press (SOURCE) repeatedly until “CD” or

“MD” appears.

2 Press (MODE) repeatedly until the desired

changer appears.

Unit number

Playback starts.

Disc number

+ 28 hidden pages