Silvercrest PS2-WLC User Manual

PS2-WLC Controller

Playstation®, PS2, PSone and PSX are registered trademarks of Sony Computer
Entertainment, Inc. This product is not sponsored, endorsed or approved by Sony Features
and/or specifications subject to change without notice.

User guide

We hope you enjoy using our PS2™ 2.4 GHz wireless controller. Please read this guide
thoroughly before using the unit.

4-WAY button
TURBO button
SELECT button
PROGRAM button
START button
CONNECT button

 button

U button

{ button

X button

RIGHT ANALOGUE JOY-
STICK (when pressed:

R3)
RX-LED
ANALOGUE button
MODE-LED

LEFT ANALOGUE JOY-
STICK (when pressed: L3)

X button

R1 button

ON/OFF switch

Battery compartment

L1 button
L2 button

Connection plug

RX-LED

CONNECT button

POWER-LED

1. Product description

This device is a wireless controller specifically for use with PlayStation2™. It can also be used
with PSONE™ and PSX™. The controller works at a frequency of 2.4 GHz, has a double
vibration feature as well as all other functions of the original SONY units. The controller also
has Turbo and Program functions.

2. Included

1 Controller; 1 receiver; 1 user manual

3. Product features

Power Supply: 3 x 1.5 V AAA batteries
Operating time: More than 6 hours
Transmission: 2.4 GHz multi-channel transmission
Range of action: 10 m
Special functions: Turbo function, programmable buttons with memory,

forced connection

4. Connecting the receiver

Insert the receiver plug into the appropriate slot on the PlayStation™ console and then
switch on the PlayStation™. The

POWER-LED on the receiver will come on. The RX-

LED will remain on as soon as the receiver is connected to the controller.

5. Inserting / replacing the batteries

Before using the controller insert the batteries into the battery compartment on the back of the
unit. To do this, open the battery compartment

polarity and close the compartment. Please ensure the controller has been switched off before
you replace the batteries. Please also read the information on safe disposal of batteries.

, insert the new batteries according to the

- 1 -

PS2-WLC Controller

Note:

 Please only use batteries or rechargeable batteries with a nominal voltage of 1.5 V.
 Please ensure the batteries are always inserted according to the correct polarity. Replace

the batteries with the same brand or similar batteries.

 There is a risk of explosion if the batteries are not replaced correctly.
 Do not attempt to recharge a non-rechargeable battery. There is a risk of explosion.
 Batteries / rechargeable batteries can be fatal if swallowed. Please store batteries out of

reach of small children. Seek medical help immediately if a battery has been swallowed.

 Do not expose the batteries to heat or flames. Never short-circuit batteries; never try to

force open batteries; never attempt to recharge non-rechargeable batteries. Batteries may
otherwise explode and cause serious injury.

 Never replace the batteries in a potentially explosive area. Sparks may be generated

while the batteries are being inserted or replaced which could cause an explosion.
Potentially explosive areas are often signposted as such, but not always. These include
filling stations, such as under below-deck areas on boats, fuel transmission stations, fuel
depots, areas in which the air may contain chemicals or particles such as grain, dust or
metallic powder, as well as all other areas in which you would normally be asked to switch
off the engine of your car.

6. Switching on and off

The on/off switch is on the back of the device. To switch the unit off move the
switch to the “OFF” position and to the “ON” position to switch it on.

7. Connecting the controller

The connection mode will initiate as soon as the On/Off switch on the underside of
the unit is switched to the ON position. The
light up briefly at the same time. If the
connection with the receiver. The

established.

RX LED goes out as soon as a connection has been

RX-LED and MODE-LED lights will

RX-LED comes on, the device is trying to establish a

8. Force connection

If several wireless controllers are connected at the same time, you can use the force
connection method to select a single controller.

Press the

and the
receiver at the same time for 15 seconds.

CONNECT button on the hand-held unit and then press the CONNECT button

on the receiver within 15 seconds to establish a connection. Now press the L3 button

SELECT button on the hand-held unit and the CONNECT button on the

9. Mode selection

Many games support an analogue controller which permit more precise input than with digital
controllers.
There must be a connection to the receiver before you can switch between the digital and

analogue modes. To do this, press the
up in analogue mode. The

Note:

 The default mode is digital.
 Not all games support digital mode.
 You may have to finish the game before switching between modes.

MODE-LED is off in digital mode.

ANALOGUE button . The MODE-LED lights

10. Energy-saving mode

The unit is equipped with an energy-saving mode to conserve energy and prolong battery life.
This mode is activated in the following situations:
 where no connection has been established between the unit and the receiver after 3

seconds

 where the unit and receiver are connected but the unit has not been used for 3 minutes
 where the connection between controller and receiver has been interrupted and no

connection has been established within 6 seconds

 where you press the

CONNECT button on the hand-held unit without pressing the

CONNECT button on the receiver within 15 seconds.

If your unit is in the energy-saving mode, press either the
buttons to reactivate the controller.

START , L3 , or R3

11. TURBO functions

With the TURBO function you can switch the U, {, X, , R1, R2, L1 and L2 buttons
to the TURBO/rapid fire function. The controller must be connected to the receiver to activate
or deactivate the TURBO function.

To activate: Press and hold the
Then press the button for which you want to activate the

To deactivate: First press the button which you want to reset. Press and hold the

TURBO button until the RX-LED comes on.

rapid fire function.

TURBO

button until the RX-LED goes out.

- 2 -