Siemens HB90325GB, HB90324GB, U1721S2GB, HB90364GB, U1721S0GB Installation instructions
...
Installation instructions
2
3
For the installer and kitchen
expert!
Important installation notes:
❑ Properly dispose of packaging materi-
als.
❑ Do not use oven door handle for trans-
porting or handling the unit during installation.
❑ WARNING: Connection and first start of
the appliance may only be performed by
an authorised specialist.
❑ Connection must be made using an
H05VV-F mains connection cable.
❑ Nominal connected loading, nominal
voltage and model number of the
appliance:
see the rating plate, located behind the
oven door, fixed to the lower left facing
edge of the oven.
❑ The unit's nameplate is located at on
the right sidewall of the unit.
❑ Electrical safety of the appliance can be
ensured only if the equipment earth in
the building installation has been installed according to regulations.
❑ On the installation side a isolating device
shall be provided.
Any switch with a contact gap exceeding
3 mm may be considered a separating
device.
Other examples are LS switches, fuses
and contactors.
❑ In the case of repairs interrupt all power
connections to the unit.
❑ Connection diagram
Kitchen furniture
Oven housing units from virtually all lines of
kitchen furniture are suitable for installing
the built-in oven. However, the veneers or
plastic laminates on the housing unit must
be applied with heat-resistant glue (90 °C). If
plastic laminate or glue are not sufficiently
heat-resistant, warping, bubbling or detachment of the finish may result.
220-240V
~
L
N
Assembly Instructions
4
Installation without cupboard
1. 2.
600
min. 38
min.
720
min.
550
0
5
Installation of the built-in oven
❑ To burn-in the insulation, heat up the
oven prior to installing the unit.
❑ Push the built-in oven into the housing
unit and align the unit until it is in a level
position.
❑ Open the oven door and, using one scr-
ew on each side, fasten the built-in oven
to the side strips of the housing unit (see
illustration).
The two screws (supplied with the builtin oven) must be started slightly outward.
❑ Verify that the built-in oven is positioned
securely and in a level position, and that
the required installation dimensions have
been maintained.
❑ The properly installed appliance must be
covered on all sides in such a fashion
that not even components with rough
insulation are exposed to the touch. The
cover must be removable with tools only.
3. 5.
4.
3.
2.
0
1.
6
Installation with cupboard
1. 2.
560-
min. 720
min. 3
min.
550
570
min. 38
min. 720
min. 3
min.
550
560-
570
min. 38
7
Installation of the built-in oven
❑ To burn-in the insulation, heat up the
oven prior to installing the unit.
❑ Push the built-in oven into the housing
unit and align the unit until it is in a level
position.
❑ Open the oven door and, using one scr-
ew on each side, fasten the built-in oven
to the side strips of the housing unit (see
illustration).
The two screws (supplied with the builtin oven) must be started slightly outward.
❑ Verify that the built-in oven is positioned
securely and in a level position, and that
the required installation dimensions have
been maintained.
❑ The properly installed appliance must be
covered on all sides in such a fashion
that not even components with rough
insulation are exposed to the touch. The
cover must be removable with tools only.
3.
NEFF (UK) Ltd.
Grand Union House,
Old Wolverton Road,
Old Wolverton
Milton Keynes, MK12 5PT
Tel: 01908 328900
Fax: 01908 328999
5750 191018 0503 Es.
Ident-Nr. 527 632
Loading...