Siemens A80485-1 Quick Start Manual

QUICK START GUIDE

SIEMENS A80485-1 GCP DISPLAY MODULE

DECEMBER 2017

DOCUMENT NO. SIG-QG-17-05

VERSION A

CONFIGURATION AND OPERATION

Siemens Industry, Inc. Rail Automation 700 East Waterfront Drive Munhall, PA 15120, USA 1-800-793-SAFE

PRINTED IN U.S.A.

SIEMENS INDUSTRY, INC. RAIL AUTOMATION

SIEMENS INDUSTRY, INC.RAIL AUTOMATION

2400 NELSON MILLER PARKWAY

939 S. MAIN STREET

LOUISVILLE, KENTUCKY 40223

MARION, KENTUCKY 42064

TELEPHONE:

(502) 618-8800

TELEPHONE:

(270) 918-7800

FAX:

(502) 618-8810

CUSTOMER SERVICE:

(800) 626-2710

SALES & SERVICE:

(800) 626-2710

TECHNICAL SUPPORT:

(800) 793-7233

WEB SITE:

USA Rail Automation Site

FAX:

(270) 918-7830

PROPRIETA RY INFORMATION

Siemens Industry, Inc. has a proprietary interest in the information contained herein and, in some

instances, has patent rights in the systems and components described. It is requested that you

distribute this information only to those responsible people within your organization who have an

official interest.

This document or the information disclosed herein, shall not be reproduced or transferred to other

documents or used or disclosed for manufacturing or for any other purpose except as specifically

authorized in writing by Siemens Industry, Inc.

TRANSLATIONS

The manuals and product information of Siemens Industry, Inc. are intended to be produced and

read in English. Any translation of the manuals and product information are unofficial and can be

imprecise and inaccurate in whole or in part. Siemens Industry, Inc. does not warrant the

accuracy, reliability, or timeliness of any information contained in any translation of manual or

product information from its original official released version in English and shall not be liable for

any losses caused by such reliance on the accuracy, reliability, or timeliness of such information.

Any person or entity that relies on translated information does so at his or her own risk.

WARRANTY IN FORMATION

Siemens Industry, Inc. warranty policy is as stated in the current Terms and Conditions of Sale

document. Warranty adjustments will not be allowed for products or components which have

been subjected to abuse, alteration, improper handling or installation, or which have not been

operated in accordance with Sel ler's instructions. Alteration or removal of any serial number or

identification mark voids the warranty.

SALES AND SERVICE LOCATIONS

Technical assistance and sales information on Siemens Industry, Inc. products may be obtained

at the following locations:

FCC RULES COMPLIANCE

The equipment covered in this manual has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his/her own expense.

SIG-QG-17-05 DECEMBER 2017 Version No.: A

ii

DOCUMENT HISTORY

Version

Release Date

Sections Changed

Details of Change

A

DEC 2017

- - - -

Initial Release

SIG-QG-17-05 DECEMBER 2017 Version No.: A

iii

List of Figures

Section Title Page

Figure 1-1 A80485 Siemens Display Module........................................................................................... 1-1

Figure 1-2 A80485 GCP Display Module Controls, Indicators, and Display ............................................ 1-2

Figure 2-1 GCP4000 and GCP5000 Main Screens ................................................................................. 2-1

Figure 2-2 GCP3000+ Main Screens ....................................................................................................... 2-1

Figure 2-3 Keypad, and Navigation Cluster Keys .................................................................................... 2-2

Figure 2-4 Keypad Operation ................................................................................................................... 2-2

Figure 2-5 Navigation Key Cluster ........................................................................................................... 2-2

Figure 3-1 Display Module to Laptop Connection .................................................................................... 3-1

Figure 3-2 Inserting a USB Drive ............................................................................................................. 3-3

Figure 3-3 USB Detected Screen ............................................................................................................ 3-3

Figure 3-4 USB Menu Screens GCP4000 and GCP5000 ....................................................................... 3-4

Figure 3-5 USB Menu Screens GCP3000+ ............................................................................................. 3-4

Figure 3-6 Display Module to GCP Module Serial Cable Connection ..................................................... 3-5

Figure 3-7 Display Module to Ethernet Power-Over-Et her net De vice Connection .................................. 3-6

Figure 3-8 Display Module to Ethernet Network Connection ................................................................... 3-7

List of Tables

Section Title Page

Table 1-1 Display Module Controls, Indicators, Connectors, and Display Descriptions .......................... 1-3

Table 1-2 Resource Documents .............................................................................................................. 1-4

v

SIG-QG-17-05 DECEMBER 2017 Version No.: A

WARNING

IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS

DENCE OVER

NOTES, CAUTIONS, AND ALL OTHER INFORMATION.

CAUTION

HAZARDOUS SITUATION AND/OR POSSIBLE DAMAGE TO EQUIPMENT. CAUTIONS TAKE PRECEDENCE OVER NOTES AND ALL OTHER INFORMATION, EXCEPT WARNINGS.

NOTE

Generally used to highlight certain information relating to the topic under discussion.

NOTES, CAUTIONS, AND WA RN INGS

Throughout this manual, notes, cautions, and warnings are frequently used to direct the reader’s

attention to specific information. Use of the three terms is defined as follows:

INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, INJURY. WARNINGS ALWAYS TAKE PRECE

REFERS TO PROPER PROCEDURES O R PRACTICES WHICH IF NOT STRICTLY OBSERVED, COULD RESULT I N A POT ENTI ALLY

If there are any questions, contact Siemens Industry, Inc. Application Engineering.

SIG-QG-17-05 DECEMBER 2017 Version No.: A

vi

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

Static electricity can damage electronic circuitry, particularly low voltage components such as the

integrated circuits commonly used throughout the electronics industry. Therefore, procedures

have been adopted industry-wide which make it possible to avoid the sometimes invisible

damage caused by electrostatic discharge (ESD) during the handling, shipping, and storage of

electronic modules and components. Siemens Industry, Inc. has instituted these practices at its

manufacturing facility and encourages its customers to adopt them as well to lessen the likelihood

of equipment damage in the field due to ESD. Some of the basic protective practices include the

following:

• Ground yourself before touching card cages, assemblies, modules, or components.

• Remove power from card cages and assemblies before removing or installing modules.

• Remove circuit boards (modules) from card cages by the ejector lever only. If an ejector lever is not

provided, grasp the edge of the circuit board but avoid touching circuit traces or components.

• Handle circuit boards by the edges only.

• Never physically touch circuit board or connector contact fingers or allow these fingers to come in

contact with an insulator (e.g., plastic, rubber, etc.).

• When not in use, place circuit boards in approved stat i c -shielding bags, contact fingers first. Remove circuit boards from static-shielding bags by grasping the ejector lever or the edge of the board only. Each bag should include a caution label on the outside indicating static-sensitive contents.

• Cover workbench surfaces used for repair of electronic equipment with static dissipative workbench matting.

• Use integrated circuit extractor/inserter tools designed to remove and install electrostatic-sensitive integrated circuit devices such as PROM’s (OK Industries, Inc., Model EX-2 Extractor and Model MOS-40 Inserter (or equivalent) are highly recommended).

• Utilize only anti-static cushioning material in equipment shipping and storage containers.

For information concerning ESD material applications, please contact the Technical Support Staff at 1-800-793-7233. ESD Awareness Classes and additional ESD product information are also available through the Technical Support Staff.

SIG-QG-17-05 DECEMBER 2017

vii

Version No.: A

TERM

DESCRIPTION

AAR:

Association of American Railroads – An organization that establishes AREMA:

American Railway Engineering and Maintenance-of-wa y Associat ion

DIAG.:

Diagnostic

DNS:

Domain Name Server

connecting to external devices and equipment.

GLOSSARY

uniformity and standardization among different railroad systems.

GCP: Grade Crossing Predictor – A train detection device used as part of a

highway-railroad grade crossing warning system to provide a relatively

uniform warning time. GPS: Globa l Posit io nin g S ystem . IP: Internet Protocol - ISO Model Layer 3 (network) protocol that performs

proper routing of packets. LAN: Local Area Network – A limited network where the data transfer medium

is generally wires or cable.

LED: Light-Emitting-Diode - A solid-state indicator. Module: Physical package including PCBs and input/output terminals for

RJ-45: Industry standard Ethernet port RS232: Industry standard serial port. RX: Receive RXD: Receive Data TX: Transmit TXD: Transmit Data USB Port: Universal Serial Bus Port USB Drive: Types of memory devices that plug into a USB port. These devices are

commonly called flash drives or memory sticks.

SIG-QG-17-05 DECEMBER 2017

viii

Version No.: A

_________________________________________________________________________________________________________

INTRODUCTION

SECTION 1 - INTRODUCTION

1.0 INTRODUCTION

The purpose of this quick start guide is to introduce GCP Users to the Siemens Next-Generation Display module, A80485-1, used on the GCP3000+, GCP4000, and GCP5000. T he scope of this guide encompasses the location and operation of the display controls, indicators, and connectors as well as addressing the initial user-configurable port parameters to enable connection to external devices, such as a laptop, external network, or Ethernet powered devices.

1.1 GCP DISPLAY MODULE

The Siemens A80485-1 Display Module is the next generation display module replacing the A80407 Display Module, offering enhanced features and improved speed and responsiveness. A restructured menu reduces programming and maintenance time in the field. The addition of two Ethernet ports offers connectivity to a network or Ethernet devices. A powered Ethernet por t is available for devices deriving their power from an Ethernet connection. The Laptop port enables the user to connect a laptop computer to the display to conf igure parameters, update software, and download logs. The display screen and keypad provide a local user interface, allowing operation without the need of a computer.

Figure 1-1 A80485 Siemens Display Module

SIG-QG-17-05 DECEMBER 2017

1-1

Version No.: A

(M9)

1

Symbol2ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS8TUV9WXYZ

HELP

0

Space

BACK

ENTER

USB

LAPTOP

DIAG

CPU

SEAR

TX RX

POWER

TX RX

DISPLAY Module A80485-2

COM

TX RX

ECHELON

ETHERNET 2ETHERNET 1

ETH PWR

ESSR

Ethernet Port

Keypad

Navigation

USB Port

Ethernet Port

Laptop

Ethernet Port

Display

Echelon®

SEAR

TX RX

COM

CPU

TX RX

Power LED

Diagnostic

INTRODUCTION _________________________________________________________________________________________________________

1.1.1 GCP Display Module Controls, Indicators, Connectors, and Display

The GCP Display module contr ols, indicators, connectors, and display are shown in Figure 1-2 and described in Table 1-1.

LEDS

TX RX LEDS

Powered

Keys

TX RX LEDS

(Unpowered)

(Diag) Port

Figure 1-2 A80485 GCP Display Module Controls, Indicators, and Display

1-2

SIG-QG-17-05 DECEMBER 2017 Version No.: A

_________________________________________________________________________________________________________

ITEM

DESCRIPTION

DISPLAY

2 ½ x 4 inch OLED Color Display

CONTROLS

Keypad

12-key membrane keypad

Navigation

5-key membrane navigational cluster

INDICATORS

Power

LED (Green)

CPU TX/RX

CPU data stream indicators TX LED (Green) RX LED (Yellow)

COM TX/RX

Communications data stream indicators TX LED (Green) RX LED (Yellow)

SEAR TX/RX

SEAR data stream indicators TX LED (Green) RX LED (Yellow)

Echelon® LAN

Echelon® LAN data indicators TX LED (Green) RX LED (Yellow)

Ethernet 1 (powered)1

Ethernet Power indicator LED (Green) Data:TX LED (Green) RX LED (Yellow)

Ethernet 21

Ethernet 2 data indicators (embedded in connector) TX LED (Green) RX LED (Yellow)

CONNECTORS

Ethernet 11

RJ-45 powered connector (See note)

Ethernet 21

RJ-45 connector

Diag (Diagnostics)

DB-9, Female Serial connector, RS-232

USB

USB 2.0 Type A connector

Laptop

RJ-45 connector

NOTE

The Ethernet 1 powered connector is designed specifically for Power-Over-Ethernet (POE) devices.

INTRODUCTION

Table 1-1 Display Module Controls, Indicators, Connectors, and Display Descriptions

Ethernet 1 data indicators (embedded in connector)

1

Ethernet 1 and Ethernet 2 ports are not available on the GCP4000, therefore these ports on

the Display module are not useable.

Siemens Ethernet Spread Spectrum Radios and may not power other

SIG-QG-17-05 DECEMBER 2017 Version No.: A

1-3

INTRODUCTION

DOCUMENT NUMBER

TITLE

SIG-00-17-03

GCP 3000+ Installation & Instruction

SIG-00-17-04

GCP 3000+ Application Guidelines

SIG-00-08-06

GCP 4000 Application Guidelines

SIG-00-08-10

GCP 4000 Field Manual

SIG-00-10-05

GCE 4000 Application Guidelines

SIG-00-12-68

GCP 4000 Plus Field Manual

SIG-00-13-03

GCP 5000 Field Manual

SIG-00-13-04

GCP 5000 Application Guidelines

SIG-00-15-05

CPU III for GCP

_________________________________________________________________________________________________________

1.2 RESOURCE DOCUMENTS

The GCP manuals and guidelines listed in Table 1-2 will provide complete and detailed information for the configuration and operation of your GCP unit. This quick start guide is a supplemental document to be used in concert with the product manuals listed in Table 1-2.

Table 1-2 Resource Documents

SIG-QG-17-05 DECEMBER 2017 Version No.: A

1-4

_________________________________________________________________________________________________________

CONFIGURATION

SECTION 2 - CONFIGURATION

2.0 CONFIGURATION

The GCP Display module default settings will normally suffice for the majority of GCP installations. This section will show some of the initial display programming options to enable the user to customize the display serial and Ethernet ports.

2.1 DISPLAY MODULE MAIN SCREENS

The display module main screens serve as the starting point for setup and operation of the GCP system. The main screens for the GCP4000 and GCP5000 are shown in Figure 2-1 and the main screens for the GCP3000+ are shown in Figure 2-2.

Figure 2-1 GCP4000 and GCP5000 Main Screens

Figure 2-2 GCP3000+ Main Screens

SIG-QG-17-05 DECEMBER 2017

2-1

Version No.: A

1

Symbol

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS8TUV

9

WXYZ

HELP

0

Space

BACK

1

Symbol

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS8TUV

9

WXYZ

HELP

0

Space

BACK

ENTER

Navigation Keys Keypad

Enter Key

Back Key

Help Key

CONFIGURATION _________________________________________________________________________________________________________

2.2 KEYPAD/NAVIGATION CLUSTER

The Keypad and Navigation Cluster shown in Figure 2-3 is the local user interface to enter data and navigate through the display menu structure. The BACK key returns to one of the main screens. The HELP key will bring up Help screens to assist the user with hints and additional information when available.

Figure 2-3 Keypad, and Navigation Cluster Keys

2.2.1 Keypad and Navigation Cluster Operation

The Display module keypad allows the user to select menus or enter data. Press the desired key multiple times to select a letter, number, or symbol. Figure 2-4 lists the alpha-numeric sequence of each key. The HELP key brings up a dialog box with instructions or information in some of the menus. The BACK key returns to one of the four main screens.

Figure 2-4 Keypad Operation

The Navigation Key Cluster shown in Figure 2-5 is used to na vigate through menus and text. The ENTER key completes the transaction.

Figure 2-5 Navigation Key Cluster

SIG-QG-17-05 DECEMBER 2017 Version No.: A

2-2

_________________________________________________________________________________________________________

NOTE

Display screens vary between GCP models and unit configuration.

Section 1.2 for the screens used by your GCP model.

2 3 1

CONFIGURATION

The following screen examples in this quick start guide are shown for general reference purposes. Refer to the applicable manual listed in

2.3 SERIAL PORT

The GCP Display has a serial port (Diag) used for diagnostic functions and transferring software updates to other modules in the GCP case. The serial port default settings are used for transferring software and therefore no serial port configuration is necessary.

2.3.1 Configuring the Serial Port

Should the user desire to change serial port settings, use the following procedure:

1. Navigate to the Program View screen using the left/right navigation keys.

2. Select Display Programming (press the 4 key or use the navigation keys to select Display Programming and then press the ENTER key).

3. From the Display screen, select Serial Port (press the 1 key or use the navigation keys and select Serial Port and then press the ENTER key).

2-3

SIG-QG-17-05 DECEMBER 2017 Version No.: A

CONFIGURATION

Laptop Port

Server*

Client

Disabled

Ethernet 1 and 2 Ports

Disabled*

Client

NOTE

The Ethernet 1 powered connector is designed specifically for Power-Over-Ethernet (POE) devices.

4

5

_________________________________________________________________________________________________________

4. From the Serial Port screen, press the ENTER key to bring up the serial port parameters

screen.

5. Set the serial port parameters as required using the keypad and navigation keys.

2.4 ETHERNET PORTS

The GCP Display has three Ethernet ports: Laptop port, Ethernet 1 (powered), and Ethernet 2 (unpowered). The setting options for these ports are:

* Denotes default setting

Siemens Ethernet Spread Spectrum Radios and may not power other

2.4.1 Ethernet Port Configuration

The Laptop Ethernet port has three modes: Server, Client, and Disabled. The Ethernet 1 and Ethernet 2 ports have two modes: Disabled and Client. Ethernet ports 1 and 2 also have additional parameters for Path Type and Protocol, which are used in conjunction with PTC and ATCS Back Office communications. Consult the GCP manual for details and information on these settings.

SIG-QG-17-05 DECEMBER 2017 Version No.: A

2-4

_________________________________________________________________________________________________________

WARNING

S BEEN CONFIGURED AS A SERVER (NOTE THIS IS THE DEFAULT SETTING), THIS WILL CAUSE DISRUPTION TO THE NETWORK. IF A NETWORK IS TO BE CONNECTED TO THE LAPTOP PORT, CONFIGURE THE LAPTOP PORT DHCP AS A CLIENT.

NOTE

visible on the screen.

1

2

CONFIGURATION

2.4.1.1 Server Mode

The Server mode is only available on the Laptop port. When connecting a laptop to the display module, set the laptop’s Ethernet DHCP as a client. The display module, acting as a DHCP server, will assign an IP address to the laptop and establish communications.

DO NOT CONNECT A NETWORK TO THE LAPTOP ETHERNET PORT IF THE PORT HA

2.4.1.2 Client Mode

The Client mode is available on all three Ethernet ports. In the Client mode, the Display Ethernet port will be assigned an IP address from the external network server.

2.4.1.3 Disabled Mode

The Disabled mode shuts off the Ethernet port. Ethernet ports 1 and 2 default setting is the disabled mode, these ports may be configured as clients f or use on a network and/or external Ethernet devices.

2.4.1.4 Laptop Ethernet Port Setup

If the user desires to change the DHCP setup of the Laptop port, use the following procedure:

1. From the Display screen (see section 2.3.1 on how to navigate to the Display screen), select Ethernet Ports (press 2 on the keypad or use the navigation keys and select Ethernet Ports then press the ENTER key).

2. Select Laptop (press 1 on the keypad or use the navigation keys and select Laptop and press

the ENTER key).

On the GCP4000, Ethernet Ports 1 & 2 are disabled and will not be

SIG-QG-17-05 DECEMBER 2017 Version No.: A

2-5

CONFIGURATION

NOTE

setting the laptop DHCP to Client.

Server

3

4

OR

Server *

5

_________________________________________________________________________________________________________

3. The Laptop DHCP Configuration default setting is Server. To Configure the port to either a

client mode or to disable the port, press the ENTER key.

4. From the DHCP Configuration screen, select the desired mode using the navigation keys and

press the ENTER key.

For Laptop operation it is recommended to use the Server mode and

5. In the Server mode the IP Address and Network Mask are pre-assigned from the factory and

cannot be changed.

SIG-QG-17-05 DECEMBER 2017 Version No.: A

2-6

_________________________________________________________________________________________________________

4

5 3 6

2

1

CONFIGURATION

2.4.1.5 Ethernet Ports 1 and 2 Setup (GCP3000+ and GCP5000 only)

Ethernet ports 1 and 2 have two modes available, Disabled and Client. The default setting is disabled. To reconfigure the Ethernet 1 or 2 ports, use the following procedure:

1. From the Program View main screen, select Display Programming (press 4 on the keypad or use the navigation keys and select Display Programming, then press the ENTER key).

2. From the Display screen, select Ethernet Ports (press 2 on the keypad or use the navigation

keys and select Ethernet Ports and press the ENTER key).

3. From the Ethernet Ports screen, select either Port 1 or Port 2 (press 2 or 3 on t he k eypad or use the navigation keys and select Port 1 or Port 2, then press the ENTER key).

4. Highlight the DHCP Configuration text and press the ENTER key.

5. Select the desired mode, Disabled or Client, (highlight using the navigation keys and press

the ENTER key).

6. The port is now set; refer to the GCP manual for further configuration of Path Type or

Protocol.

SIG-QG-17-05 DECEMBER 2017

2-7

Version No.: A

CONFIGURATION

Server

_________________________________________________________________________________________________________

2.4.1.6 DNS (Domain Name System) Setup

The Display DNS setup has three default server addresses. The user can reconfigure up to three of these addresses to match their network operations. Refer to the GCP manual for further instructions on setting DNS servers.

2.4.1.7 Ethernet Port Status

The status of the Display module Ethernet ports can be viewed by selecting the Stat us tab on the Laptop, Ethernet 1 or Ethernet 2 screen. The status of all three ports can be viewed regardless of which Ethernet port screen is selected.

2.4.2 Display Options Settings

The Display Options not covered in this quick guide are detailed in the product manual for your specific GCP model. See Table 1-2.

SIG-QG-17-05 DECEMBER 2017

2-8

Version No.: A

_________________________________________________________________________________________________________

OPERATION

SECTION 3 - OPERATION

3.0 OPERATION

This section will provide an overview of the Display module operation.

3.1 DISPLAY MODULE LAPTOP INTERFACE

The Display module Laptop port provides an interface for connecting a laptop to the GCP unit. The laptop port can also be used for other Ethernet functions when properly configured.

3.1.1 Display Module to Laptop Connection

To connect a laptop to the Display module, plug an RJ-45 to RJ-45 Ethernet cable from the Laptop port on the front panel of the Display module to any Ethernet port on the laptop. The Display module DHCP should be set up as a server and the laptop DH CP set up as a client. Using a web browser on the laptop, enter the Display IP address (192.168.255.81) in the browser address text box to connect to the display. The Siemens Web User Interface (Web UI) will appear on the computer web browser. Refer to the GCP manual for your GCP unit for further information on using the Web UI.

Figure 3-1 Display Module to Laptop Connection

SIG-QG-17-05 DECEMBER 2017

3-1

Version No.: A

OPERATION

NOTE

folders titled GCP4000 for all GCP models

_________________________________________________________________________________________________________

3.2 USB OPERATION

The USB port on the front panel of the Display module is used to install software on the Display module or any of the modules in the GCP unit, as well as downloading logs and reports to a USB Drive.

3.2.1 USB Drive File Structure

The USB Drive requires that a specific file structure be created on the USB Drive prior to use on the Display USB port. The GCP system looks for specific file folders to locate, upload, or download files.

The file structure is as follows:

•SIEMENS o <DOT#>-<SITE NAME>

 GCP4000

 CONFIGURATIONS

• .PAC FILES

 REPORTS

• <YYYY><MON>

•GCP4000

o APPLICATIONS

 .MCF  .PAC

o EXECUTIVES

 .MEF  .TGZ  .BIN

PAC files or MCFs to be uploaded should be placed under the GCP4000\Applications. Executive software to be uploaded should be placed under the GCP4000\Executives. Downloaded files are placed under the Siemens\<DOT#>-<Sitename>\GCP4000 folder.

Due to the software commonality, the USB Display device utilizes

SIG-QG-17-05 DECEMBER 2017 Version No.: A

3-2

(M9)

1

Symbol2ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS8TUV9WXYZ

HELP

0

Space

BACK

ENTER

USB

LAPTOP

DIAG

CPU

SEAR

TX RX

POWER

TX RX

DISPLAY Module A80485-2

COM

TX RX

ECHELON

ETHERNET 2ETHERNET 1

ETH PWR

_________________________________________________________________________________________________________

OPERATION

3.2.2 USB Menu

To activate the USB Menu, insert a USB drive, with the created file structure, into the USB port on the front of the Display module as shown in Figure 3-2.

Figure 3-2 Inserting a USB Drive

3.2.3 USB Detection

When the USB drive is inserted into the USB port, the Display module will display a screen advising the USB drive has been detected. Press the ENTER key on the navigation key cluster, to bring up the USB Menu or press the BACK key on the keypad to exit.

Figure 3-3 USB Detected Screen

SIG-QG-17-05 DECEMBER 2017 Version No.: A

3-3

OPERATION _________________________________________________________________________________________________________

3.2.4 USB Menu

The USB menu has eight sub-menus shown in Figure 3-4 and Figure 3-5. The Software Updates menu has two sub-menus, one for software updates for modules and the second for the Display module Executive software update. The other USB menu sub-menus provide for downloading of configuration reports, display/event logs, GCP logs, train history, and uploading or downloading configuration files. The GCP’s current configuration information can be downloaded to the USB drive. A new configuration can also be uploaded to the GCP via the USB drive. Refer to the appropriate manual for your GCP unit for details for uploading and downloading configuration information into the GCP.

Figure 3-4 USB Menu Screens GCP4000 and GCP5000

Figure 3-5 USB Menu Screens GCP3000+

SIG-QG-17-05 DECEMBER 2017

3-4

Version No.: A

(M9)

1

Symbol

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS

8

TUV

9

WXYZ

HELP

0

Space

BACK

ENTER

USB

LAPTOP

DIAG

CPU

SEAR

TX

RX

POWER

TX RX

DISPLAY Module A80485-2

COM

TX RX

ECHELON

ETHERNET 2ETHERNET 1

ETH PWR

R

Made in USA

DIAG

POWER

HEALTH

OUT 2

IN 2

IN 1

OUT 1

MOTION ISLAND

DAX C

DAX G PRE-EMPT

DAX E DAX F

DAX D

DAX B

DAX A

PRIME

S1

Module A80418

TRACK

_________________________________________________________________________________________________________

OPERATION

3.3 MODULE SOFTWARE UPDATES

Module Software updates are performed using a USB Drive connected to the Display USB port or using a Laptop connected to the Display module Laptop port. Transfer of the software to individual modules is accomplished using the Display module Diag serial port. Connect a DB-9 male to DB-9 male serial cable with a Null Modem adapter between the Display module Diag port and the Diag port of the GCP module receiving the software update as shown in Figure 3-6. Refer to the appropriate manual for your GCP for further details on uploading software to GCP modules.

3.4 DISPLAY MODULE POWERED ETHERNET PORT

The Display module Ethernet 1 port is a powered port for external Ethernet devices that derive their power from an Ethernet connection.

Figure 3-6 Display Module to GCP Module Serial Cable Connection

SIG-QG-17-05 DECEMBER 2017 Version No.: A

3-5

NOTE

connector is designed specifically for

Power-Over-Ethernet (POE) devices.

(M9)

1

Symbol

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS8TUV9WXYZ

HELP

0

Space

BACK

ENTER

USB

LAPTOP

DIAG

CPU

SEAR

TX RX

POWER

TX RX

DISPLAY Module A80485-2

COM

TX RX

ECHELON

ETHERNET 2ETHERNET 1

ETH PWR

J1 J2

OPERATION _________________________________________________________________________________________________________

The Ethernet 1 powered Siemens Ethernet Spread Spectrum Radios and may not power other

3.4.1 Display Module to Ethernet 1 Port Power-Over-Ethernet (POE) Device Connection

An example of an Ethernet 1 port Power-Over-Ethernet device connection using the Siemens Ethernet Spread Spectrum Radio is shown in Figure 3-7. Connection from the GCP Display to the Ethernet powered device is usually connected using an Ethernet cable that is provided with the Ethernet device. Refer to the Ethernet device instructions for further information.

SIG-QG-17-05 DECEMBER 2017 Version No.: A

Figure 3-7 Display Module to Ethernet Power-Over-Ethernet Device Connection

3-6

_________________________________________________________________________________________________________

WARNING

THE NETWORK. IF A NETWORK IS TO BE CONNECTED TO THE LAPTOP PORT, CONFIGURE THE LAPTOP PORT DHCP AS A CLIENT.

(M9)

1

Symbol2ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PQRS8TUV

9

WXYZ

HELP

0

Space

BACK

ENTER

USB

LAPTOP

DIAG

CPU

SEAR

TX RX

POWER

TX RX

DISPLAY Module A80485-2

COM

TX RX

ECHELON

ETHERNET 2ETHERNET 1

ETH PWR

To

3.5 ETHERNET NETWORK CONNECTION

The GCP unit can be remotely accessed using an Ethernet network connection. Ethernet 1 and Ethernet 2 ports on the Display module are generally used for such a connection, however, the Laptop port can be used for this purpose as well using a RJ-45 to RJ-45 Ethernet cable. Set the port to be used to the Client mode ( see Section 2.4.1.5 for details or for the Laptop port see Section 2.4.1.4), the external network will assign the Display module an IP address and establish communications.

DO NOT CONNECT A NETWORK TO THE LAPTOP ETHERNET PORT IF THE PORT HAS BEEN CONFIGURED AS A SERVER, THIS WILL CAUSE DISRUPTION TO

Ethernet

Network

Figure 3-8 Display Module to Ethernet Network Connection

SIG-QG-17-05 DECEMBER 2017 Version No.: A

3-7

OPERATION

OPERATION _________________________________________________________________________________________________________

This Page Intentionally Left Blank

SIG-QG-17-05 DECEMBER 2017

3-8

Version No.: A

NOTES

Siemens Industry, Inc.

Rail Automation

2400 Nelson Miller Parkway

Louisville, Kentucky 40223

(502) 618-8800

Siemens Industry, Inc.

Rail Automation

700 East Waterfront Drive

Munhall, Pennsylvania 15120

(412) 461-2501

Siemens A80485-1 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

PROPRIETA RY INFORMATION

TRANSLATIONS

WARRANTY IN FORMATION

SALES AND SERVICE LOCATIONS

FCC RULES COMPLIANCE

DOCUMENT HISTORY

Table of Contents

List of Figures

List of Tables

NOTES, CAUTIONS, AND WA RN INGS

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

GLOSSARY

SECTION 1 - INTRODUCTION

1.0 INTRODUCTION

1.1 GCP DISPLAY MODULE

1.1.1 GCP Display Module Controls, Indicators, Connectors, and Display

1.2 RESOURCE DOCUMENTS

SECTION 2 - CONFIGURATION

2.0 CONFIGURATION

2.1 DISPLAY MODULE MAIN SCREENS

2.2 KEYPAD/NAVIGATION CLUSTER

2.2.1 Keypad and Navigation Cluster Operation

2.3 SERIAL PORT

2.3.1 Configuring the Serial Port

2.4 ETHERNET PORTS

2.4.1 Ethernet Port Configuration

2.4.1.1 Server Mode

2.4.1.2 Client Mode

2.4.1.3 Disabled Mode

2.4.1.4 Laptop Ethernet Port Setup

2.4.1.5 Ethernet Ports 1 and 2 Setup (GCP3000+ and GCP5000 only)

2.4.1.6 DNS (Domain Name System) Setup

2.4.1.7 Ethernet Port Status

2.4.2 Display Options Settings

SECTION 3 - OPERATION

3.0 OPERATION

3.1 DISPLAY MODULE LAPTOP INTERFACE

3.1.1 Display Module to Laptop Connection

3.2 USB OPERATION

3.2.1 USB Drive File Structure

3.2.2 USB Menu

3.2.3 USB Detection

3.2.4 USB Menu

3.3 MODULE SOFTWARE UPDATES

3.4 DISPLAY MODULE POWERED ETHERNET PORT

3.4.1 Display Module to Ethernet 1 Port Power-Over-Ethernet (POE) Device Connection

3.5 ETHERNET NETWORK CONNECTION