Sharp XG-C55X User Manual

OPERATION MANUAL
MODEL
XG-C55X
Introduction
Connections and Setup
Basic Operation
LCD PROJECTOR
Easy to Use Functions
IMPORTANT
For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 14.
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.
Model No.: XG-C55X
Serial No.:
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/ EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that:
If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
or and of the same rating as
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese) and Korean. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch (Traditionelles Chinesisch und einfaches Chinesisch) und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois, espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et chinois simplifié) et coréen. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska (traditionell kinesiska och förenklad kinesiska) och koreanska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español, italiano, holandés, portugués, chino (chino tradicional y chino simplificado) y coreano. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per luso in inglese, tedesco, francese, svedese, spagnolo, italiano, olandese, portoghese, cinese (cinese tradizionale e cinese semplificato) e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans, Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees) en Koreaans. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês, (Chinês Tradicional e Chinês Simplificado) e Coreano. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
See bottom of actual set.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
The lightning flash with arrowhead symbol,
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
DO NOT REMOVE COVER.
PERSONNEL.
within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Introduction
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip­ment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
-1
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. During normal operation, when putting the projector into the standby mode always use the STANDBY button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning the Lamp Replacement
See Replacing the Lamp” on page 85.
LAMP REPLACEMENT CAUTION
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XGC55X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS
PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
PRECAUTIONS A OBSERVER LORS DU REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE
AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XGC55X//1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 786,432 pixels (× RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
When Attaching the “QUICK GUIDE” Label
Attaching the QUICK GUIDE Label (supplied) on the projector will help you check the setup procedure. When you attach the QUICK GUIDE Label on the projector, be sure to align the label bottom and the upper part of the Notevision logo on the top cabinet of the projector as shown in the drawing on the right.
-2
“QUICK GUIDE” Label

Outstanding Features

1. Ultra High Brightness from a Compact Projector
300W SHP Lamp Use 300W SHP lamp for excellent color uniformity and ultra high brightness.
Power Save mode function enables lower noise levels, reduced power consumption and longer lamp life.
2. Simple & Easy Operation
Color coded terminals, automatic signal search and graphical menu sys­tem insure easy set-up and configuration.
Frequently used connections and controls are strategically placed for easy access.
Simple lens replacement
Using an easy access lens cover and a new bayonet mount configuration, the optional lens can be easily installed.
3. Superior PC Compatibility
Compatible with up to 200 Hz vertical refresh rate, Sync on Green and Composite Sync signals for use with a wide variety of high-end PCs and Workstations.
Using Advanced Intelligent Compression Technology, computer screens of UXGA (1,600 # 1,200) resolution can be displayed with minimal distortion.
Introduction
4. Advanced Computer & Video lntegrated Composer Technology
Realizes vivid images using the latest image quality circuitry.
New I/P conversion algorithm enhances the performance of the motion detect I/P
conversion.
Extensive improvements on the jagged edges or slanted lines in moving images.
Color Management System
Supports sRGB. Enables individual settings of lightness, chromatic value and hue for six target colors.
Noise Reduction
Allows for a clear image even with noisy source signals.
New Edge Up-Scaling
Reduces jaggies and flickering when up-scaling edges of slanted lines, enabling sharper quality images.
5. Theft Deterrent and Security
Anti-theft This feature will render the projector useless if a keycode is not entered.
Notevision Lock Down
A secure installation is achieved by tethering one of the projector’s mounting points to the optical block. This added measure makes it ex­tremely difficult to pull the projector off of its ceiling mount thus mini­mizing the chance of injury from horseplay or unauthorized removal of the projector.
-3

Contents

Introduction
Outstanding Features ......................................... 3
Contents............................................................... 4
IMPORTANT SAFEGUARDS ............................... 6
How to Access the PDF Operation Manuals
(Windows, Macintosh) ................................... 9
Part Names ........................................................ 10
Projector (Front and Top View) ................................ 10
Projector (Rear View) .............................................. 11
Remote Control (Front View) ................................... 12
Remote Control (Top View) ..................................... 12
Using the Remote Control ................................ 13
Available Range of the Remote Control ................. 13
Inserting the Batteries ............................................. 13
Accessories ....................................................... 14
Connections and Setup
Connecting the Projector to Other Devices .... 16
Before Connecting.................................................. 16
This projector can be connected to: ....................... 16
Connecting the Power Cord ................................... 17
Connecting the Projector to a Computer ............. 17
Connecting to Video Equipment .......................... 19
Connecting to an Amplifier .................................. 21
Controlling the Projector by a Computer ............. 22
Connecting to a Monitor ...................................... 23
Using as a Wired Remote Control ....................... 23
Using the Wireless Presentation Function of the
Remote Control ............................................. 24
Setup .................................................................. 25
Using the Adjustment Feet ..................................... 25
Adjusting the Lens .................................................. 26
Setting up the Screen ..............................................27
Screen Size and Projection Distance ...................... 28
Projecting a Reversed/Inverted Image ................... 32
Basic Operation
Setting with the Buttons
Image Projection ............................................... 34
Basic Procedure ......................................................34
Selecting the On-screen Display Language ........... 36
Turning the Power off .............................................. 37
Correcting Trapezoidal Distortion
(Keystone Correction) ................................. 38
Setting with the Menus
Menu Bar Items ................................................. 40
Using the Menu Screen .................................... 42
Menu Selections (Adjustments) .............................. 42
Menu Selections (Settings) ..................................... 44
Adjusting the Picture ........................................ 46
Adjusting Image Preferences ..................................46
Selecting the Signal Type ....................................... 46
Progressive Mode.................................................... 47
Adjusting Computer Images ............................ 48
Computer Image Adjustment .................................. 48
Saving Adjustment Settings..................................... 48
Selecting Adjustment Settings ................................49
Special Mode Settings ............................................49
Checking the Input Signal ....................................... 49
Auto Sync Adjustment .............................................50
Auto Sync Display Function ................................... 50
Easy to Use Functions
Selecting the Picture Display Mode ................ 52
Displaying a Still Image .................................... 54
Enlarging a Specific Portion of an Image ....... 55
Gamma Correction Function............................ 56
Displaying Dual Pictures (Pict in Pict) ............ 57
Black Screen Function ..................................... 58
Displaying the Break Timer .............................. 59
Color Management System (C. M. S.) .............. 60
Selecting the Color Reproduction Mode ................. 60
Selecting the Target Color ....................................... 60
Setting the Brightness of the Target Color ...............61
Setting the Chromatic Value of the Target Color ......61
Setting the Hue of the Target Color ........................ 61
Resetting User-Defined Color Settings................... 62
Overview of All Color Settings ................................. 62
Setting the Audio Output Type ......................... 63
Setting on/off the Internal Speaker.................. 63
Auto Search Function ....................................... 64
Video Digital Noise Reduction
(DNR) System .............................................. 65
Setting On-screen Display ............................... 65
Setting the Video System ................................. 66
Saving Projected Images .................................. 67
Capturing the Image .............................................. 67
Deleting the Captured Image ..................................67
Setting a Background Image ............................ 68
Selecting a Startup Image ................................ 68
Selecting the Economy Mode .......................... 69
Setting the Power Save Mode ................................. 69
Monitor Out/RS-232C Off Function ..........................69
Auto Power Off Function ......................................... 70
Displaying the Remaining Lamp Life
(Percentage) ................................................. 70
Reversing/Inverting Projected Images ............ 71
Locking the Operation Buttons
on the Projector ........................................... 71
Setting up the Keylock ............................................ 71
Canceling the Keylock Setting ................................ 72
-4
Selecting the Transmission Speed
(RS-232C) ..................................................... 72
Setting up a Password ...................................... 73
Entering the Password............................................. 73
Changing the Password ......................................... 74
If You Forget Your Password ................................... 74
Setting the Anti-Theft........................................ 75
Entering the Keycode ..............................................75
Changing the Keycode ........................................... 76
Initializing the Settings ..................................... 77
Displaying the Adjustment Settings................ 78
Appendix
Maintenance ...................................................... 80
Replacing the Air Filter ..................................... 81
Maintenance Indicators .................................... 83
Regarding the Lamp ......................................... 85
Lamp ...................................................................... 85
Caution Concerning the Lamp ................................ 85
Replacing the Lamp ................................................ 85
Removing and Installing the Lamp Unit ................. 86
Resetting the Lamp Timer ....................................... 87
Connecting Pin Assignments .......................... 88
(RS-232C) Specifications and
Command Settings ...................................... 89
Wired Remote Control Terminal
Specifications .............................................. 92
Computer Compatibility Chart ......................... 93
Troubleshooting ................................................ 94
For SHARP Assistance ..................................... 96
Specifications .................................................... 97
Dimensions ........................................................ 98
Glossary ............................................................. 99
Index ................................................................. 100
Introduction
-5

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10.Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a book­case or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with a
grounding terminal. This plug will only fit into a grounding type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to qualified service personnel.
-6
Introduction
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen
into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation. e. If the product has been dropped or damaged in
any way. f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
INTELLECTUAL PROPERTY RIGHTS
IMPORTANT
READ BEFORE USING THE PRODUCT
You have acquired a product that includes software licensed to SHARP Corporation by Lineo, Inc. (“Lineo”). The Software is protected by copyright laws, international copyright treaties, and other intellectual prop­erty laws and treaties. Lineo and its suppliers retain all ownership of, and intellectual property rights in (including copyright), the Software components and all copies thereof, provided however, that certain components of the Software are components licensed under the GNU General Public License (version
2), which Lineo supports. You may obtain a copy of the GNU General Public License at http://www.fsf.org/ copyleft/gpl.html. Lineo will provide source code for any of the components of the Software licensed under the GNU General Public License. To obtain such source code, send email to embedix­support@lineo.com.
OS: Embedix (Embedded Linux) Embedix (TM) is a registered trademark of
U.S.A. LINEO, Inc.
Microsoft, Windows and PowerPoint are registered trademarks of Microsoft Corporation in the United States and/or other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the United States.
Adobe Acrobat is a trademark of Adobe Systems Incorporated.
Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
This software is based in part on the work of the Independent JPEG Group.
All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
-7
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for a replacement. See Replacing the Lamp on page 85.
Cautions concerning the setup of the projector
For minimal servicing and to maintain high image qual­ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environ­ments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places exposed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the cur­tains and dim the lights when setting up the screen in a sunny or bright room.
The projector may safely be tilted to a maximum angle of 12 degrees.
Placement should be within ±12 degrees.
Be sure that the intake vent and the exhaust vent are
not obstructed.
If the cooling fan becomes obstructed, a protection cir­cuit will automatically put the projector into the standby mode. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the in­take and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
Cautions regarding the transportation of the pro­jector
When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra caution with the lens. Before mov­ing the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables con­nected to it.
Other connected equipment
When connecting a computer or other audio-visual equip­ment to the projector, make the connections AFTER un­plugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.
Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.
Using the projector in other countries
The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector over­seas, be sure to use the appropriate power cord for the country you are in.
Do not subject the projector to hard impact and/ or vibration.
Take care with the lens so as not to hit or damage the surface of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will make your eyes tired. Be sure to occasionally rest your eyes.
Avoid locations with high or low temperature.
The operating temperature for the projector is from 41°F to 104°F (+5°C to +40°C).
The storage temperature for the projector is from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
Allow at least 7.9 inches (20 cm) of space between the exhaust vent and the nearest wall or obstruction.
-8
Temperature monitor function
If the projector starts to overheat due to setup problems or block­age of the air vents, and will blink in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning in­dicator on the projector will blink, and after a 90-sec­ond cooling-off period the projector will enter the standby mode. Refer to Maintenance Indicators on page 83 for details.
Info
The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.
Do not unplug the power cord during projection or cool­ing fan operation. This can create damage due to the rise in internal temperature, as the cooling fan also stops.

How to Access the PDF Operation Manuals (Windows, Macintosh)

PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector, even if you do not have this manual. To utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet, you can install it from the CD-ROM.
To install Acrobat Reader from the CD-ROM
For Windows:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the My Computer icon. 3 Double click the CD-ROM drive. 4 Double click the ACROBAT folder. 5 Double click the language (name of the folder)
that you want to view.
6 Double click the installation program and
follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the appropriate version from the Internet.
Accessing the PDF Manuals
For Windows:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the My Computer icon. 3 Double click the CD-ROM drive. 4 Double click the MANUALS folder. 5 Double click the language (name of the
folder) that you want to view.
6 Double click the “C55X pdf file to access the
projector manuals.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the CD-ROM icon. 3 Double click the ACROBAT folder. 4 Double click the language (name of the folder)
that you want to view.
5 Double click the installation program and
follow the instructions on the screen.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the CD-ROM icon. 3 Double click the MANUALS folder. 4 Double click the language (name of the
folder) that you want to view.
5 Double click the “C55X pdf file to access the
projector manuals.
Introduction
Note
If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file using the “File”, “Open menu.
See the “readme.txt file on the CD-ROM for important information not included in this operation manual.
-9

Part Names

Numbers in refer to the main pages in this operation manual where the topic is explained.

Projector (Front and Top View)

For turning the power on.
ON button
Power indicator
Illuminates red, when the
projector is in standby.
When the power is turned
on, this indicator will
illuminate green.
STANDBY button
For putting the projector into
the standby mode.
Lamp indicator
Illuminates green indicating
normal function. Replace
the lamp when the indicator
illuminates red.
Temperature warning
indicator
When the internal
temperature rises, this
indicator will illuminate red.
UNDO button
For undoing an operation or returning to the default
settings.
34
34
37
83
83
39
STANDBY
INPUT button
35
For switching input mode 1, 2, 3 or 4.
KEYSTONE button
38
For adjusting Keystone or Digital Shift setting.
AUTO SYNC button
50
For automatically adjusting images when connected to a computer.
Adjustment buttons
42
(', ", \, |)
For selecting menu items.
35
VOLUME buttons
For adjusting the speaker sound level.
MENU button
42
For displaying adjustment and setting screens.
ENTER button
42
For setting items selected or adjusted on the menu.
HEIGHT ADJUST
button
Adjustment foot
Carrying handle
-10
25
25
Attaching and removing the lens cap
Press on the two buttons of the lens cap and attach it on the lens. Then release the buttons to lock it in place.
Press on the two buttons of the lens cap and remove it from the lens.
In this operation manual, the illustration and the screen display are simplified for explana­tion, and may differ slightly from actual display.
Zoom knob
26
Focus ring
26
Intake vent
80
Remote control
13
sensor
Air filter/cooling
81
fan (Intake vent) (on the bottom of the projector)

Projector (Rear View)

RS-232C terminal
For controlling
projector using a
computer.
AUDIO OUTPUT
terminal
Shared audio
output terminal for
INPUT 1, 2, 3 and 4.
INPUT 1 terminal
Terminal for
computer RGB and
component signals.
OUTPUT (INPUT 1, 2)
terminal
Shared computer
RGB and component
signals output
terminal
for INPUT 1 and 2.
INPUT 2 terminal
Terminal for
computer RGB and
component signals.
22
21
17
23
17
17
23
19
19
19
17
Introduction
AUDIO INPUT 1, 2 terminal
Shared audio input terminal for INPUT 1 and 2.
WIRED REMOTE control input terminal
INPUT 3 terminal
For connecting video equipment.
AUDIO (L/R) INPUT 3, 4 terminals
Shared audio input terminals for INPUT 3 and 4.
INPUT 4 terminal
Terminal for connecting video equipment with an S-video terminal.
AC socket
Exhaust vent
80
Kensington Security Standard connector
Adjustment Feet
25
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
Carrying the projector
Before carrying the projector, fully extend the carrying handle.
-11
Part Names

Remote Control (Front View)

For putting the projector into the
STANDBY button
standby mode.
KEYSTONE button
For adjusting Keystone or Digital
Shift setting.
ENTER button
For setting items selected or
adjusted on the menu.
UNDO button
For undoing an operation or
returning to the default settings.
ENLARGE (Enlarge/Reduce)
buttons
For enlarging or reducing part of
the image.
GAMMA button
For correcting the brightness of an image, when the images displayed
are hard to see because of the
brightness of the room. Four
gamma modes are available to
choose from.
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
INPUT buttons
For switching to the respective
input modes.
37
38
42
39
55
56
50
35
ON button
34
For turning the power on.
MENU button
42
For displaying adjustment and setting screens.
Adjustment buttons
42
(', ", \, |)
For selecting menu items.
PinP button
57
For displaying dual pictures.
24
FORWARD/BACK buttons
Same function as the [Page Down] and [Page Up] keys on a computer keyboard when using the Remote receiver.
FREEZE button
54
For freezing images.
BLACK SCREEN button
58
For superimposing a black screen.
RESIZE button
52
For switching the screen size (NORMAL, BORDER, etc).
MUTE button
36
For temporarily turning off the sound.
For adjusting the speaker sound
VOLUME buttons
35
level.
Remote Control (Top View)
Remote control signal transmitters
-12
13
BREAK TIMER button
59
For displaying the break timer.
WIRED R/C JACK
23
For controlling the projector by connecting the remote control to the projector.

Using the Remote Control

Available Range of the Remote Control

The remote control can be used to control the projector within the ranges shown in the illustration.
Introduction
Note
The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal may differ due to the screen material.
When using the remote control:
Be sure not to drop, expose to moisture or high temperature.
The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo­rescent lamp.

Inserting the Batteries

The batteries (two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar)) are included in the package.
1 Pull down the tab on the cover
and remove the cover towards the direction of the arrow.
2 Insert the included batteries.
Insert the batteries making sure the polarities correctly match the
marks inside the battery
compartment.
and
Remote control signal transmitters
30°
30°
Remote control
45°
23' (7 m)
Remote control sensor
3 Insert the lower tab of the
cover into the opening, and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
Insert the batteries making sure the polarities correctly match the and marks inside the battery compart- ment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak. Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth.
The batteries included with this projector may exhaust over a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
-13

Accessories

Supplied accessories
Remote control RRMCGA176WJSA
Power cord
(1)
Two R-6 batteries (AA size, UM/SUM-3, HP-7 or similar)
(2) (3)
(4)
For U.S., Canada, etc. (11'10" (3.6 m)) QACCDA010WJPZ
For Europe, except U.K. (6' (1.8 m)) QACCVA011WJPZ
For U.K., Hong Kong and Singapore (6' (1.8 m)) QACCBA012WJPZ
Note
Use the power cord that corresponds to the wall outlet in your country.
RGB cable (9'10" (3 m)) QCNWGA012WJPZ
Lens cap (attached) PCAPHA003WJSA
DIN-D-sub RS-232C adaptor (5 QCNWGA015WJPZ
Extra air filter PFILDA005WJZZ
57
/64'' (15 cm))
USB cable (3'3" (1 m)) QCNWG0007CEPZ
Projector manual and technical reference CD-ROM UDSKAA035WJZZ
Sharp Advanced Presen­tation
Software CD-ROM
UDSKAA036WJZZ
For Australia, New Zealand and Oceania (6' (1.8 m)) QACCLA014WJPZ
Remote receiver RUNTKA061WJZZ
Sharp Advanced Presentation quick installation guide TINS-A867WJZZ
Quick guide label TLABZA364WJZZ
Operation manual (this manual)
Software
Optional cables
3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP
Computer RGB cable (32'10'' (10.0 m)) AN-C10BM (15-pin mini D-sub male connector)
5 BNC to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3BN
RS-232C serial control cable (32'10" (10.0 m)) AN-C10RS
Some of the cables may not be available depending on the region. Please check with your near-
Note
-14
est Sharp Authorized Projector Dealer or Service Center.

Connections and Setup

Connections and Setup

Connecting the Projector to Other Devices

Before Connecting

Note
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connections are made.
Be sure to read the operation manuals of the devices to be connected before making connections.

This projector can be connected to:

A computer using:
An RGB cable and a computer audio cable (commercially avail­able) (See page 17.)
A DIN-D-sub RS-232C adaptor and an RS-232C serial control cable (AN-C10RS) (sold separately) (See page 22.)
Component video or audio-visual equipment:
A VCR, Laser disc player or other audio-visual equipment (See page 19.)
A DVD player or DTV* decoder (See page 20.)
*DTV is the umbrella term used to describe the new digital television system in the United States.
An amplifier or audio components using:
An audio cable (commercially available) (See page 21.)
A monitor using:
An RGB cable (See page 23.)
A computer RGB cable (AN-C10BM) (sold separately)
(See page 23.)
-16
Supplied
Connecting the Power
accessory
Cord
Plug in the supplied power cord into the AC socket on the rear of the pro­jector.

Connecting the Projector to a Computer

Power code
Connections and Setup
Connecting to a Computer Using the RGB Cable
1 Connect the projector to the
computer using the supplied RGB cable.
Secure the connectors by tightening the thumbscrews.
2
To input audio signal, connect the projector to the computer
using the computer audio cable (commercially available or avail­able as Sharp service part QCNWGA013WJPZ).
Note
See page 93 “Computer Compatibility Chart” for a list of computer signals com­patible with the projector. Use with com­puter signals other than those listed may cause some of the functions not to work.
When connecting the projector to a com­puter in this way, select “RGB” for “Signal Type” in the “Picture” menu. See page 46.
A Macintosh adaptor may be required for use with some Macintosh computers. Con­tact your nearest Sharp Authorized Projector Dealer or Service Center.
Depending on the computer you are us­ing, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer operation manual for switch­ing the computer signal output settings.
Supplied accessory
Notebook computer
To RGB output terminal
To audio output terminal
RGB cable
RGB cable
1
Computer audio cable (commercially
2
available or available as Sharp service part QCNWGA013WJPZ)
-17
Connecting the Projector to Other Devices
Connecting the thumbscrew cables
Connect the thumbscrew cable making sure that it
fits correctly into the terminal. Then, firmly secure the connectors by tightening the screws on both sides of the plug.
Do not remove the ferrite core attached to the RGB
cable.
Ferrite core
“Plug and Play” function (when connecting to a 15-pin terminal)
This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
Before using the “Plug and Play function, be sure to turn on the projector first and the connected
computer last.
Note
The DDC “Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible computer.
-18

Connecting to Video Equipment

Connecting to Video Equipment Using an S-video, a Composite Video or an Audio Cable
Using an S-video, video, or audio cable, a VCR, laser disc player or other audio-visual equip­ment can be connected to INPUT 3, INPUT 4 and AUDIO (L/R) input terminals.
To S-video output terminal
To video output terminal
To audio output terminal
1 Connect the projector to the
video equipment using an S­video cable or a composite video cable (both commercially available).
2 Connect the projector to the
video equipment using an au­dio cable (commercially avail­able).
VCR or other audio-visual equipment
Audio cable (commercially available)
2
Composite video cable
1
(commercially available)
S-video cable (commercially available)
1
Connections and Setup
Note
The INPUT 4 (S-VIDEO) terminal uses a video signal system in which the picture is separated into color and luminance sig­nals to realize a higher-quality image. To view a higher-quality image, use a com­mercially available S-video cable to con­nect the INPUT 4 terminal on the projec­tor and the S-video output terminal on the video equipment.
-19
Connecting the Projector to Other Devices
Connecting to Component Video Equipment
Use a 3 RCA to 15-pin D-sub cable when con­necting to the INPUT 1 or 2 terminal, compo­nent video equipment such as DVD players and DTV* decoders.
*DTV is the umbrella term used to describe the new digital television system in the United States.
1 Connect the projector to the
video equipment using the 3 RCA to 15-pin D-sub cable.
2 Connect the projector to the
video equipment using a ø3.5 mm stereo minijack to RCA au­dio cable (commercially avail­able).
Note
When connecting the projector to the video equipment in this way, select “Com- ponent for Signal Type in the Picture menu. See page 46.
A ø3.5 mm stereo minijack to RCA audio cable (commercially available) is required for audio input.
Optional cable
3RCA to 15-pin D-sub cable AN-C3CP (9'10" (3.0 m))
To analog component output terminal
To audio output terminal
DVD player or DTV* decoder
3 RCA to 15-pin
1
D-sub cable (sold separately)
ø3.5 mm stereo minijack to RCA audio cable
2
(commercially available)
-20

Connecting to an Amplifier

Connecting to an Amplifier or Other Audio Components
Using a ø3.5 mm stereo minijack to RCA au­dio cable, an amplifier or other audio compo­nents can be connected to the AUDIO OUT­PUT terminal.
Audio input terminal
Connections and Setup
Connect the projector to the using a ø3.5 mm
audio cable (commercially
RCA
stereo minijack
amplifier
available).
Info
By using external audio components, the volume can be amplified for better sound.
The AUDIO OUTPUT terminal allows you to output audio to audio components from the selected AUDIO input terminal (for INPUT 1 and 2) or AUDIO (L/R) input ter­minals (for INPUT 3 and 4) connected to audiovisual equipment.
For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 63.
A ø3.5 mm stereo minijack to RCA audio cable (commercially available) is required for audio input.
to
Amplifier
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
-21
Connecting the Projector to Other Devices

Controlling the Projector by a Computer

Connecting to a Computer Using a DIN­D-sub RS-232C Adaptor and an RS-232C Serial Control Cable
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-232C adaptor and an RS-232C serial con­trol cable (cross type, sold separately), the computer can be used to control the projec­tor and check the status of the projector. See page 89 for details.
1 Connect the supplied DIN-D-
sub RS-232C adaptor to an RS­232C serial control cable (sold separately).
2 Use the above cables to con-
nect the projector and the com­puter.
Note
Do not connect or disconnect an RS-232C serial control cable to or from the com­puter while it is on. This may damage your computer.
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.
See page 88 for connection of an RS- 232C serial control cable.
Supplied accessory
Optional cable
DIN-D-sub RS-232C adaptor
RS-232C serial control cable AN-C10RS (32'10" (10.0 m))
RS-232C terminal
Desktop computer
DIN-D-sub RS-232C adaptor
RS-232C serial control cable (sold separately)
-22

Connecting to a Monitor

Watching Images on Both the Projector and a Monitor
You can display computer images on both the projector and a separate monitor using two sets of an RGB cable. An RGB cable is sup­plied with this projector. You need to buy an­other RGB cable for connecting the projector to a monitor.
1 Connect the projector to the
computer and monitor using RGB cables (one is supplied, the other is sold separately).
2 In the “Options(1)” menu, se-
lect Economy Mode, Mntr. out/RS232 and then ON”. (see page 69.)
Note
Analog RGB signals as well as Component signals can be output to the monitor.
Supplied accessory
Optional cable
(sold separately)
Computer RGB cable AN-C10BM (32'10" (10.0 m))
To RGB input terminal
RGB cable
RGB cable
(supplied)
RGB cable
Connections and Setup
Monitor
Desktop computer
To RGB output terminal

Using as a Wired Remote Control

WIRED REMOTE control input terminal
Connecting the Remote Control to the Projector
When the remote control cannot be used due to the range or positioning of the projector (rear pro­jection, etc.), connect a ø3.5 mm stereo or mono minijack cable (commercially available or available as Sharp service part QCNWGA013WJPZ) from the WIRED R/C JACK on the top of the remote con­trol to the WIRED REMOTE control input terminal.
Note
FORWARD/BACK presentation control can­not be used when the remote control is wired to the projector. To utilize this feature, dis­connect the cable from the remote control.
To WIRED R/C JACK
ø3.5 mm stereo or mono minijack cable (commercially available or available as Sharp service part QCNWGA013WJPZ)
-23
Connecting the Projector to Other Devices

Using the Wireless Presentation Function of the Remote Control

By connecting the remote receiver to a computer, wireless presentation control is possible. BACK and FORWARD buttons on the remote control will emulate the [Page Up] and [Page Down] keys on your computer keyboard. This will allow you to remotely navigate applicable presentation programs such as Microsoft PowerPoint®.
Using the Wireless Pre­sentation Function
1 Connect the remote receiver to
the computer using the sup­plied USB cable.
Note
This function only works with the Microsoft Windows OS and Mac OS. However, this function does not work with the following operation systems that do not support USB.
Versions earlier than Windows 95.
Versions earlier than Windows
NT4.0.
Versions earlier than Mac OS 8.5.
USB cable
Supplied accessories
Remote receiver
Computer
USB terminal
Remote receiver
USB cable
2 Press
or
while using presentation software on your computer.
-24
-24
Press
Press
to move the page up.
to move the page down.
BACK button
FORWARD button

Setup

Using the Adjustment Feet

The height of the projector can be adjusted using the adjustment feet at the front and back of the projector when the surface the projec­tor is placed on is uneven or when the screen is slanted. The projection of the image can be made higher by adjusting the projector when it is in a location lower than the screen.
1 Press HEIGHT ADJUST.
2 Lift the projector to adjust its
height and remove your finger from HEIGHT ADJUST.
Up
HEIGHT ADJUST button
Adjustment foot
Adjustment feet
Connections and Setup
3 Rotate the adjustment feet at
the back of the projector for fine adjustment.
Note
When returning the projector to its original position, hold the projector firmly, press HEIGHT ADJUST and then gently lower it.
The projector is adjustable up to approxi­mately 12 degrees on the front and 3 degrees on the back from the standard po­sition.
Info
Do not press HEIGHT ADJUST when the adjustment foot is extended without firmly holding the projector.
Do not hold the lens when lifting or lower­ing the projector.
When lowering the projector, be careful not to get your finger caught in the area between the adjustment foot and the projector.
Down
-25
Setup

Adjusting the Lens

The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector.
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by mov-
ing the zoom knob.
Focus ring
Zoom knob
-26
Zoom out
in
Zoom

Setting up the Screen

Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
A polarizing screen cannot be used with this projector.
Three optional lenses from Sharp are also available for specialized application. Contact your local Sharp Authorized Projector Dealer for details on the lens. (Refer to the lens installation manual when attaching a lens.)
Throw Distance
The graph below is for 100 inches (254 cm) screen with 4:3 normal mode.
Screen
AN-C12MZ 7'11" – 10' (2.4 – 3.0m) Throw ratio 1:1.18 – 1.48
AN-C27MZ 17'9" – 28'1'' (5.4 – 8.6m) Throw ratio 1:2.7 – 4.3
Connections and Setup
11'11" – 15'4" (3.6 – 4.7m) Throw ratio 1:1.77 – 2.25
5 10 15 20 25 30 35 40 (ft)
Standard
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according to the desired picture size. (See page 28.)
Example of Standard Setup
Side View
90°
Audience
Top View
90°
The distance from the screen to the projector
may vary depending on the size of the screen.
The default setting can be used, when placing the
projector in front of the screen. If the projected im­age is reversed or inverted, readjust the setting to “Front” in “PRJ Mode”. P.71
Place the projector so that an imaginary horizontal
line that passes through the center of the lens is perpendicular to the screen.
AN-C41MZ 27' – 38'1'' (8.2 – 11.6m) Throw ratio 1:4.1 – 5.8
P.28
-27
Setup

Screen Size and Projection Distance

Base line:
Screen
H
L:Projection distance
Standard Lens Throw ratio 1:1.77 to 2.25
NORMAL Mode (4:3)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height Maximum [L1] Minimum [L2]
300" (762 cm)
250" (635 cm) 200" (508 cm) 150" (381 cm)
200" (508 cm)
150" (381 cm)
100" (254 cm) 80" (203 cm)
84" (213 cm) 67" (170 cm) 50" (127 cm)
72" (183 cm) 58" (147 cm)
60" (152 cm) 48" (122 cm) 36" (91 cm)
40" (102 cm) 32" (81 cm) 24" (61 cm)
240" (610 cm)
160" (406 cm)
120" (305 cm)
180"(457 cm)
120" (305 cm)
90" (229 cm)
60" (152 cm)
43" (109 cm)
46' 4" (14.1 m) 36' (11.0 m) 17 11 / 16" (45.0 cm)
38' 7" (11.8 m) 30' (9.1 m) 14 3 / 4" (37.5 cm)
30'10" (9.4 m) 24' (7.3 m) 11 13 / 16" (30.0 cm)
23' 1" (7.0 m) 17'11" (5.5 m) 8 7 / 8" (22.5 cm)
15' 4" (4.7 m) 11'11" (3.6 m) 5 7 / 8" (15.0 cm)
12'11" (3.9 m) 10' (3.0 m) 4 15 / 16" (12.6 cm)
11' (3.4 m) 8' 6" (2.6 m) 4 1 / 4" (10.8 cm)
9' 2" (2.8 m) 7' 1" (2.2 m) 3 9 / 16" (9.0 cm)
6' 1" (1.8 m) 4' 8" (1.4 m) 2 3 / 8" (6.0 cm)
Horizontal line passing through the lens center
Distance from the lens center to the bottom of the image [H]
Lens center
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft) =
(0.0472χ – 0.0517) / 0.3048
L2 (ft) =
(0.0367χ – 0.0529) / 0.3048
H (in) =
(0.1499χ – 0.0064) / 2.54
[m, cm]
L1 (m) =
0.0472χ – 0.0517
L2 (m) =
0.0367χ – 0.0529
H (cm) =
0.1499χ – 0.0064
STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height Maximum [L1] Minimum [L2]
300" (762 cm) 261" (663 cm)
250" (635 cm) 218" (554 cm)
225" (572 cm) 196" (498 cm)
200" (508 cm)
150" (381 cm)
133" (338 cm) 116" (295 cm)
106" (269 cm)
100" (254 cm) 87" (221 cm)
92" (234 cm) 80" (203 cm)
84" (213 cm) 73" (185 cm)
72" (183 cm) 63" (160 cm) 35" (89 cm)
60" (152 cm) 52" (132 cm) 29" (74 cm)
40" (102 cm) 35" (89 cm) 20" (51 cm)
174" (442 cm)
131" (333 cm)
92" (234 cm)
147" (373 cm)
123" (312 cm)
110" (279 cm)
98" (249 cm)
74" (188 cm)
65" (165 cm)
52" (132 cm)
49" (124 cm)
45" (114 cm)
41" (104 cm)
50' 6" (15.4 m) 39' 3" (12.0 m) –4 15 / 16"(–12.6 cm)
42' (12.8 m) 32' 8" (10.0 m) –4 1 / 8"(–10.5 cm)
37'10" (11.5 m) 29' 5" (9.0 m) –3 3 / 4" (–9.5 cm)
33' 7" (10.2 m) 26' 1" (8.0 m) –3 5 / 16"(–8.4 cm)
25' 2" (7.7 m) 19' 7" (6.0 m) –2 1 / 2" (–6.3 cm)
22' 3" (6.8 m) 17' 4" (5.3 m) –2 3 / 16"(–5.6 cm)
17' 9" (5.4 m) 13' 9" (4.2 m) –1 3 / 4" (–4.5 cm)
16' 9" (5.1 m) 13' (4.0 m) –1 5 / 8" (–4.2 cm)
15' 5" (4.7 m) 11'11" (3.6 m) –1 9 / 16"(–3.9 cm)
14' (4.3 m) 10'11" (3.3 m) –1 3 / 8" (–3.5 cm)
12' (3.7 m) 9' 4" (2.8 m) –1 3 / 16"(–3.0 cm)
10' (3.0 m) 7' 9" (2.4 m) 31 / 32"(–2.5 cm)
6' 7" (2.0 m) 5' 2" (1.6 m) 11 / 16"(–1.7 cm)
Distance from the lens center
to the bottom of the image [H]
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft) = L2 (ft) = H (in) =
[m, cm]
L1 (m) = L2 (m) = H (cm) =
(0.0514χ – 0.0516) / 0.3048 (0.04χ – 0.0523) / 0.3048 (–0.0422χ + 0.0018) / 2.54
0.0514χ – 0.0516
0.04χ – 0.0523 –0.0422χ + 0.0018
Note
There is an error of ± 3% in the formula above.
Values with a minus () sign indicate the distance of the lens center below the bottom of the image.
-28
AN-C41MZ (Optional accessory) Throw ratio 1:4.1 to 5.8
NORMAL Mode (4:3)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height Maximum [L1] Minimum [L2]
300" (762 cm) 240" (610 cm)
250" (635 cm) 200" (508 cm) 150" (381 cm)
200" (508 cm) 160" (406 cm)
150" (381 cm)
100" (254 cm) 80" (203 cm)
84" (213 cm) 67" (170 cm) 50" (127 cm)
72" (183 cm) 58" (147 cm)
60" (152 cm) 48" (122 cm) 36" (91 cm)
40" (102 cm) 32" (81 cm) 24" (61 cm)
120" (305 cm)
STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height Maximum [L1] Minimum [L2]
300" (762 cm) 261"(663 cm)
250" (635 cm) 218"(554 cm)
225" (572 cm)
200" (508 cm) 174"(442 cm)98"
150" (381 cm) 131"(333 cm)74"
133" (338 cm)
106" (269 cm)
100" (254 cm) 87"
92" (234 cm) 80"
84" (213 cm) 73"
72" (183 cm) 63" 35" (89 cm)
60" (152 cm) 52" 29" (74 cm)
40" (102 cm) 35"
196"(498 cm)
116"(295 cm)65"
92" 52" (132 cm)
(234 cm)
(221 cm)
(203 cm)
(185 cm)
(160 cm)
(132 cm)
(89 cm)
180" (457 cm)
120" (305 cm)
90" (229 cm)
60" (152 cm)
43" (109 cm)
147" (373 cm)
123" (312 cm)
110" (279 cm)
(249 cm)
(188 cm)
(165 cm)
49" (124 cm)
45" (114 cm)
41" (104 cm)
20" (51 cm)
114' 6"
94' 10"
75' 11"
57'
23'
123' 10"
103' 3"
93'
82' 8"
62' 1"
55' 1"
44'
41' 6"
38' 2"
34' 11"
29' 11"
25'
16' 10"
1"38'
1"32'
6"27'
5"15'
(34.9 m)
(28.9 m)
(23.1 m)
(17.4 m)
(11.6 m)
(9.8 m)
(8.4 m)
(7.0 m)
(4.7 m)
(37.8 m)
(31.5 m)
(28.3 m)
(25.2 m)
(18.9 m)
(16.8 m)
(13.4 m)
(12.7 m)
(11.6 m)
(10.6 m)
(9.1 m)
(7.6 m)
(5.1 m)
81'
67' 2"
53' 9"
27'
11'
87' 9"
73'
65' 11"
58' 8"
44'
39'
31'
29'
27'
24'
10"
21'
17'
10"
12'
(24.7 m)
(20.5 m)
(16.4 m)
5"40'
(12.3 m)
9"22'
7"19'
4"16'
(26.8 m)
2"
(22.3 m)
(20.1 m)
(17.9 m)
(13.4 m)
1"
(11.9 m)
2"
6"
2"
4"
Distance from the lens center
to the bottom of the image [H]
17
7 / 8"
14
7 / 8"
11
59 / 64"
8
15 / 16"
15 / 16"
(8.2 m)
(6.9 m)
(6.0 m)
(5.0 m)
(3.4 m)
(9.5 m)
(9.0 m)
(8.3 m)
(7.6 m)
(6.5 m)
(5.4 m)
(3.7 m)
5
5
"
4
19 / 64"
37 / 64"
3
23 / 64"
2
Distance from the lens center
to the bottom of the image [H]
3 / 64"
–5
11 / 64"
–4
25 / 32"
–3
11 / 32"
–3
33 / 64"
–2
1 / 4"
–2
49 / 64"
–1
11 / 16"
–1
17 / 32"
–1
27 / 64"
–1
7 / 32"
–1
1 / 32"
1
43 / 64"
(45.4 cm)
(37.8 cm)
(30.3 cm)
(22.7 cm)
(15.1 cm)
(12.7 cm)
(10.9 cm)
(9.1 cm)
(6.0 cm)
(–12.8 cm)
(–10.6 cm)
(–9.6 cm)
(–8.5 cm)
(–6.4 cm)
(–5.7 cm)
(–4.5 cm)
(–4.3 cm)
(–3.9 cm)
(–3.6 cm)
(–3.1 cm)
(–2.6 cm)
(–1.7 cm)
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft)
=
(0.1158χ + 0.0403) / 0.3048
L2 (ft) =
(0.0818χ + 0.0606) / 0.3048
H (in) =
(0.1514χ – 0.0071) / 2.54
[m, cm]
L1 (m)
=
0.1158χ + 0.0403
L2 (m) =
0.0818χ + 0.0606
H (cm) =
0.1514χ – 0.0071
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft)
=
(0.1255χ + 0.0951) / 0.3048
L2 (ft) =
(0.0888χ + 0.0975) / 0.3048
H (in) =
(–0.0425χ – 0.001) / 2.54
[m, cm]
L1 (m) =
0.1255χ + 0.0951
L2 (m) =
0.0888χ + 0.0975
H (cm) =
–0.0425χ – 0.001
Connections and Setup
Note
There is an error of ± 3% in the formula above.
Values with a minus () sign indicate the distance of the lens center below the bottom of the image.
-29
Setup
AN-C27MZ (Optional accessory) Throw ratio 1:2.7 to 4.3
NORMAL Mode (4:3)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width
300" (762 cm) 240" (610 cm)
250" (635 cm) 200" (508 cm) 150" (381 cm)
200" (508 cm) 160" (406 cm)
150" (381 cm)
100" (254 cm) 80" (203 cm)
84" (213 cm) 67" (170 cm) 50" (127 cm)
72" (183 cm) 58" (147 cm)
60" (152 cm) 48" (122 cm) 36" (91 cm)
40" (102 cm) 32" (81 cm) 24" (61 cm)
120" (305 cm)
STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width
300" (762 cm) 261" (663 cm)
250" (635 cm) 218" (554 cm)
225" (572 cm)
200" (508 cm) 174" (442 cm) 98" (249 cm)
150" (381 cm) 131" (333 cm) 74" (188 cm)
133" (338 cm)
106" (269 cm)
100" (254 cm) 87" (221 cm)
92" (234 cm) 80" (203 cm)
84" (213 cm) 73" (185 cm)
72" (183 cm) 63" (160 cm) 35" (89 cm)
60" (152 cm) 52" (132 cm) 29" (74 cm)
40" (102 cm) 35" (89 cm) 20" (51 cm)
196" (498 cm)
116" (295 cm) 65" (165 cm)
92" (234 cm) 52" (132 cm)
eight
H
180" (457 cm)
120" (305 cm)
90" (229 cm)
60" (152 cm)
43" (109 cm)
eight
H
147" (373 cm)
123" (312 cm)
110" (279 cm)
49" (124 cm)
45" (114 cm)
41" (104 cm)
Maximum [L1] Minimum [L2]
85' 2"
(26.0 m)
70' 11"
(21.6 m)
56' 8"
(17.3 m)
42' 4"
(12.9 m)
1"28'
(8.6 m)
6"23'
(7.2 m)
1"20'
(6.1 m)
8"16'
(5.1 m)
11'
92' 8"
77' 2"
69' 5"
61' 8"
46' 2"
40' 10"
32' 6"
30' 7"
28' 1"
25' 7"
21' 11"
18' 2"
12'
(3.4 m)
Maximum [L1] Minimum [L2]
(28.3 m)
(23.5 m)
(21.2 m)
(18.8 m)
(14.1 m)
(12.5 m)
(9.9 m)
(9.3 m)
(8.6 m)
(7.8 m)
(6.7 m)
(5.5 m)
(3.7 m)
54' 2"
45' 1"
36'
6' 10"
59' 1"
49'
44' 3"
39' 3"
29' 4"
25'
20'
19'
17'
16'
13'
11'
7' 6"
10"26'
10"14'
11"
10"
10"
9"17'
8"12'
6"10'
2"
7"
5"
2"
5"
(16.5 m)
(13.7 m)
(11.0 m)
(8.2 m)
(5.4 m)
(4.5 m)
(3.9 m)
(3.2 m)
(2.1 m)
(18.0 m)
(15.0 m)
(13.5 m)
(12.0 m)
(8.9 m)
(7.9 m)
(6.3 m)
(5.9 m)
(5.4 m)
(4.9 m)
(4.2 m)
(3.5 m)
(2.3 m)
Distance from the lens center to the bottom of the image [H]
63 / 64"
17
14
11
8
5
5
4
3
2
Distance from the lens center to the bottom of the image [H]
–5
–4
–3
–3
–2
–2
–1
–1
–1
–1
–1
61 / 64"
31 / 32"
31 / 32"
63 / 64"
3 / 64"
21 / 64"
37 / 64"
13 / 32"
"
11 / 64"
47 / 64"
11 / 32"
33 / 64"
13 / 64"
49 / 64"
21 / 32"
17 / 32"
27 / 64"
7 / 32"
–63 / 64"
–43 / 64"
(45.7 cm)
(38.0 cm)
(30.4 cm)
(22.8 cm)
(15.2 cm)
(12.8 cm)
(11.0 cm)
(9.1 cm)
(6.1 cm)
(–12.7 cm)
(–10.6 cm)
(–9.5 cm)
(–8.5 cm)
(–6.4 cm)
(–5.6 cm)
(–4.5 cm)
(–4.2 cm)
(–3.9 cm)
(–3.6 cm)
(–3.1 cm)
(–2.5 cm)
(–1.7 cm)
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft) L2 (ft) = H (in) =
[m, cm]
L1 (m) L2 (m) = H (cm) =
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft) L2 (ft) = H (in) =
[m, cm]
L1 (m) = L2 (m) = H (cm) =
=
(0.087χ – 0.1353) / 0.3048 (0.0555χ – 0.1377) / 0.3048 (0.1522χ – 0.002) / 2.54
=
0.087χ – 0.1353
0.0555χ – 0.1377
0.1522χ – 0.002
=
(0.0946χ – 0.1356) / 0.3048 (0.0605χ – 0.1377) / 0.3048 (–0.0424χ + 0.0013) / 2.54
0.0946χ – 0.1356
0.0605χ – 0.1377
–0.0424χ + 0.0013
Note
There is an error of ± 3% in the formula above.
Values with a minus () sign indicate the distance of the lens center below the bottom of the image.
-30
AN-C12MZ (Optional accessory) Throw ratio 1:1.18 to 1.48
NORMAL Mode (4:3)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height Maximum [L1] Minimum [L2]
300" (762 cm) 240" (610 cm)
250" (635 cm) 200" (508 cm) 150" (381 cm)
200" (508 cm) 160" (406 cm)
150" (381 cm)
100" (254 cm) 80" (203 cm)
84" (213 cm) 67" (170 cm) 50" (127 cm)
72" (183 cm) 58" (147 cm)
60" (152 cm) 48" (122 cm) 36" (91 cm)
40" (102 cm) 32" (81 cm) 24" (61 cm)
120" (305 cm)
STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height Maximum [L1] Minimum [L2]
300" (762 cm) 261" (663 cm)
250" (635 cm) 218" (554 cm)
225" (572 cm)
200" (508 cm) 174" (442 cm) 98" (249 cm)
150" (381 cm) 131" (333 cm) 74" (188 cm)
133" (338 cm)
106" (269 cm)
100" (254 cm) 87" (221 cm)
92" (234 cm) 80" (203 cm)
84" (213 cm) 73" (185 cm)
72" (183 cm) 63" (160 cm) 35" (89 cm)
60" (152 cm) 52" (132 cm) 29" (74 cm)
40" (102 cm) 35" (89 cm) 20" (51 cm)
196" (498 cm)
116" (295 cm) 65" (165 cm)
92" (234 cm) 52" (132 cm)
180" (457 cm)
120" (305 cm)
90" (229 cm)
60" (152 cm)
43" (109 cm)
147" (373 cm)
123" (312 cm)
110" (279 cm)
49" (124 cm)
45" (114 cm)
41" (104 cm)
30' 5" (9.3 m) 24' 3" (7.4 m) 17 3 / 4" (45.1 cm)
25' 4" (
7.7
m) 20' 2" (
20' 3" (6.2 m) 16' 1" (4.9 m) 11 13 / 16" (30.0 cm)
15' 2" (4.6 m) 12' (3.7 m) 8 7 / 8" (22.5 cm)
10' (3.0 m) 7' 11" (2.4 m) 5 7 / 8" (15.0 cm)
8' 4" (2.5 m) 6' 8" (2.0 m) 4 15 / 16" (12.6 cm)
7' 2" (2.2 m) 5' 8" (1.7 m) 4 1 / 4" (10.8 cm)
5'11" (1.8 m) 4' 8" (1.4 m) 3 9 / 16" (9.0 cm)
3'11" (1.2 m) 3' 1" (0.9 m) 2 3 / 8" (6.0 cm)
33' 2" (10.1 m) 26' 5" (8.0 m) –5"
27' 7" (8.4 m) 22' (6.7 m) –4 3 / 16"(–10.6 cm)
24'10" (7.6 m) 19' 9" (6.0 m) –3 3 / 4" (–9.5 cm)
22' 1" (6.7 m) 17' 7" (5.3 m) –3 3 / 8" (–8.5 cm)
16' 6" (5.0 m) 13' 2" (4.0 m) –2 1 / 2" (–6.4 cm)
14' 7" (4.4 m) 11' 7" (3.5 m) –2 3 / 16"(–5.6 cm)
11' 7" (3.5 m) 9' 3" (2.8 m) –1 3 / 4" (–4.5 cm)
10'11" (3.3 m) 8' 8" (2.6 m) –1 5 / 8" (–4.2 cm)
10' 1" (3.1 m) 8' (2.4 m) –1 9 / 16"(–3.9 cm)
9' 2" (2.8 m) 7' 3" (2.2 m) –1 7 / 16"(–3.6 cm)
7'10" (2.4 m) 6' 3" (1.9 m) –1 3 / 16"(–3.0 cm)
6' 6" (2.0 m) 5' 2" (1.6 m) 31 / 32"(–2.5 cm)
4' 3" (1.3 m) 3' 4" (1.0 m) 11 / 16"(–1.7 cm)
Distance from the lens center
to the bottom of the image [H]
6.1
m) 14 13 / 16" (37.6 cm)
Distance from the lens center
to the bottom of the image [H]
(–12.7 cm)
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft) =
(0.0311χ – 0.0676) / 0.3048
L2 (ft) =
(0.0248χ – 0.0693) / 0.3048
H (in) =
(0.1504χ – 0.0328) / 2.54
[m, cm]
L1 (m) =
0.0311χ – 0.0676
L2 (m) =
0.0248χ – 0.0693
H (cm) =
0.1504χ – 0.0328
The formula for picture size and projection distance
χ
: Picture size (diag.) (in)
[Feet, inches]
L1 (ft) =
(0.0339χ – 0.0669) / 0.3048
L2 (ft) =
(0.027χ – 0.0683) / 0.3048
H (in) =
(–0.0424χ + 0.0079) / 2.54
[m, cm]
L1 (m) =
0.0339χ – 0.0669
L2 (m) =
0.027χ – 0.0683
H (cm) =
–0.0424χ + 0.0079
Connections and Setup
Note
There is an error of ± 3% in the formula above.
Values with a minus (–) sign indicate the distance of the lens center below the bottom of the image.
-31
Setup

Projecting a Reversed/Inverted Image

Projection from behind the screen
Place a translucent screen between the projector and the au­dience.
Reverse the image by setting Rear in PRJ Mode. See page 71 for use of this function.
When using the default setting.
On-screen Display
Projection using a mirror
Place a mirror (normal flat type) in front of the lens.
Info
When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of the audience.
Ceiling-mount setup
It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount bracket (sold separately).
AN-XGCM55 ceiling-mount bracket, its AN-EP101B
extension tube and AN-JT200 universal bracket, adaptor for non-level ceiling installation (for U.S.A.).
BB-M20T ceiling adaptor, its BB-NVHOLDER280,
BB-NVHOLDER550, BB-NVHOLDER900 ceiling mount systems (for GERMANY).
AN-60KT ceiling-mount bracket, its AN-TK201 and AN-TK202
extension tubes (for countries other than the U.S.A. and GERMANY).
Be sure to adjust the position of the pro­jector to match the distance (H) from the lens center position (see page 28) to the lower edge of the image, when mounting the projector on the ceiling.
Invert the image by setting Ceiling + Front in PRJ Mode. See page 71 for use of this function.
The image is reversed.
When using the default setting.
On-screen Display
The image is inverted.
-32

Basic Operation

Basic Operation

Image Projection

Basic Procedure

Connect the required external equipment to the pro­jector before operating the following procedures.
Info
The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language ac­cording to the procedure on page
36
.
1 Plug the power cord into the
wall outlet.
The power indicator illuminates red, and the projector enters the standby mode.
ON
2 Press
the remote control.
The power indicator illuminates green. After the lamp indicator illuminates, the projector is ready to start operation.
The lamp indicator illuminates, indi­cating the status of the lamp.
If the projector is put into the standby mode and immediately turned on again, the lamp indicator may take time to illuminate.
When controlling the projector using RS-232C commands from a com­puter, wait for at least 40 seconds after the power has been turned on, and then transmit the commands.
on the projector or on
Note
Green: The lamp is ready. Green blinking: The lamp is
warming up or shutting down.
Red:
The lamp should be replaced.
Power
indicator
Lamp
indicator
ON button
ENTER
button
ENTER
button
INPUT button
',", \, | buttons
MENU button
ON button
MENU button
', ", \, | buttons
When “Anti-Theft” (see page 75) is set, the keycode input box will appear.
Enter the keycode.
Note
When entering the keycode, press the buttons previously set on the projector or the remote control.
Info
When “Anti-Theft” is set, enter the keycode or the input display will not ap­pear. Even when the signal is input, the display will not appear. (see page 75.)
-34
Keycode input box
3 Press , , or on
the remote control to select the INPUT mode.
After pressing
use to select the desired input mode.
once on the projector,
"On-screen Display (Example)
INPUT 1 mode
Using RGB
Note
When no signal is received, “NO SIGNAL. will be displayed. When a signal that the projector is not pre­set to receive is received, NOT REG. will be displayed.
When “Auto Search is ON, the INPUT modes with signals can be selected. (see page 64.)
The INPUT mode is not displayed when OSD display is set to Level A or Level B. (see page 65.)
About the INPUT modes
INPUT 1 INPUT 2 (RGB/ Component)
INPUT 3 (Video)
INPUT 4 (S-Video)
Used for projecting im­ages from equipment that sends RGB signals or component signals con­nected to the RGB input terminal.
Used for ages connected to the VIDEO input terminal.
Used for projecting im­ages from equipment connected to the S­VIDEO input terminal.
projecting
from equipment
im-
Using Component
INPUT 2 mode
Using RGB
Using Component
➝➝
INPUT 3 mode
Using Video
Basic Operation
INPUT 4 mode
Using S-Video
4 Press
or
on the remote
control to adjust the volume.
Note
Pressing
Pressing
On the projector, the volume can be
adjusted by pressing
,
as cursor buttons (\, |) when the menu screen is active.
will lower the volume.
will raise the volume.
on the projector operate
INPUT buttons
VOLUME buttons
or .
-35
Image Projection
5 Press to temporarily turn
off the sound.
Note
Pressing
sound back on.
again will turn the

Selecting the On-screen Display Language

The on-screen display language of the projec­tor can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese.
1 Press .
The menu will be displayed.
2 Press \ or | to select Lan-
guage”.
3 Press ' or " to select the de-
sired language, and then press
.
4 Press .
The desired language will be set as the on-screen display.
-36

Turning the Power off

1
Press
or
on the remote control, then press that button again while the confirmation message is displayed, to put the projec­tor into the standby mode.
Note
If you accidentally pressed
STANDBY
to put the projector into the standby mode, wait until the confirmation message disappears.
The projector cannot be operated while a message Shutting Down. Please Wait. is displayed.
2
Unplug the power cord from the AC outlet after the cooling fan stops.
on the projector
STANDBY
or and do not want
STANDBY button
ENTER button
MENU button
', ", \, | buttons
MUTE button
Basic Operation
Info
Do not unplug the power cord dur­ing projection or cooling fan opera­tion. This can cause damage due to the rise in internal temperature, as the cooling fan also stops.
-37

Correcting Trapezoidal Distortion (Keystone Correction)

Correcting Trapezoidal Distortion
This function allows for Keystone (On-screen Trapezoidal Distortion) Correction.
Note
When the image is projected either from top or from bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal dis­tortion is called Keystone Correction.
The Keystone Correction can be adjusted up to angle of approximately ±35 degrees.
1 Press
Pressing
DER, STRETCH or SMART STRETCH screen is displayed will start the Digital Shift function. See page 39.
.
again while the BOR-
2 Press ', ", \ and | to adjust
the Keystone correction.
If you want to make more detailed cor­rections, press
pattern, and then press
||
| to make the adjustments.
||
to display the test
''
""
\\
',
",
\ and
''
""
\\
KEYSTONE button
ENTER button
UNDO button
Normal screen
Compresses upper side.
Compresses lower side.
', ", \, | buttons
Keystone Correction screen
Note
Since the trapezoidal distortion of the im­age can be corrected up to an angle of approximately ±35 degrees, the actual screen can be diagonally set up to that angle as well.
Press
When no signal is detected, the test pat­tern will be displayed without pressing
3 Press
You can use the same settings used in NORMAL mode 4:3 for 16:9.
Straight lines or the edges of images may appear jagged while adjusting the image.
-38
to cancel Keystone Correction.
.
Note
Test pattern
.
Digital Shift Setting
For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television
system in the United States.
Press ' to move the projected image upwards.
Press to reset the image.
UNDO button
Note
The Digital Shift function works with BORDER, STRETCH or SMART STRETCH screen. For details, see page 53.
To access Digital Shift function, press twice. The Digital Shift menu will appear when a compatible 16:9 signal is displayed.
Press " to move the projected image downwards.
Press to reset the image.
Basic Operation
-39

Menu Bar Items

This list shows the items that can be set in the projector.
INPUT 1 / 2 Mode
Main menu Sub menu
Picture
Page 46
C.M.S.
Page 60
Fine Sync
Page 48
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Signal Type
Progressive Mode
Color Selected
Target
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp [ON/OFF]
+150–150
+150–150
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+3–3
+30–30
+30–30
+30–30
+30–30
+60–60
RGB Component
2D Progressive 3D Progressive Film Mode
Standard
sRGB
[R] Red [Y] Yellow [G] Green [C] Cyan [B] Blue [M] Magenta
Resolution
1
1024 × 768
2
800 × 600
7
Resolution
1
1024 × 768
2
800 × 600
7
Resolution
1024 × 864
1
1152 × 864
2
1152 × 870
3
1152 × 882
4
7
Resolution Hor Freq Vert Freq
OFF Normal High Speed
Custom 3Custom 1
Vert Freq
Vert Freq
1024 × 768
48.4 KHz 60 Hz
60 Hz 75 Hz
60 Hz 75 Hz
Main menu Sub menu
Options (1)
Page 63
Options (2)
Page 70
Language
Page 36
Status
Page 78
Audio Out
Speaker [ON/OFF]
Auto Search [ON/OFF]
DNR
OSD Display
Image Capture
Background
Startup Image
Economy Mode
Lamp Life
PRJ Mode
Keylock Level
RS-232C
Password
Anti-Theft
All Reset
English Deutsch Español Nederlands Français Italiano Svenska Português
FAO VAO
OFF
Level 3
Level 1
Normal Level A Level B
Save Image Delete
Sharp Custom Blue None
Sharp Custom None
Power Save [ON/OFF] Mntr.out/RS232 [ON/OFF] Auto Power Off [ON/OFF]
Front Ceiling + Front Rear Ceiling + Rear
Normal Level A Level B
9600 bps 38400 bps 115200 bps
Old Password New Password Reconfirm
Old Code New Code Reconfirm
Note
The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
Only when the signal type is set as “Component, in the Picture menu of INPUT 1 or 2 Color, Tint and “Sharp” are displayed. Some items cannot be reset, even when “All Reset” in Options (2) has been selected. For details see page 77.
-40
INPUT 3 / 4 Mode
Main menu Sub menu Main menu Sub menu
Picture Page 46
C.M.S.
Page 60
Options (1)
Page 63
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Progressive Mode
Color Selected
Target
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
Audio Out
Speaker [ON/OFF]
Auto Search [ON/OFF]
DNR
OSD Display
Video System
Background
Startup Image
Economy Mode
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+3–3
2D Progressive 3D Progressive Film Mode
Standard
[R] Red [Y] Yellow
+30–30
[G] Green [C] Cyan
+30–30
[B] Blue [M] Magenta
+30–30
FAO VAO
OFF Level 1
Normal Level A Level B
Auto PAL (50/60Hz) SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N
Sharp Custom Blue None
Sharp Custom None
Power Save [ON/OFF] Mntr.out/RS232 [ON/OFF] Auto Power Off [ON/OFF]
Custom 3Custom 1
Level 3
Options (2)
Page 70
Language
Page 36
Status Page 78
Lamp Life
PRJ Mode
Keylock Level
RS-232C
Password
Anti-Theft
All Reset
English Deutsch Español Nederlands Français Italiano Svenska Português
Front Ceiling + Front Rear Ceiling + Rear
Normal Level A Level B
9600 bps 38400 bps 115200 bps
Old Password New Password Reconfirm
Old Code New Code Reconfirm
Basic Operation
-41

Using the Menu Screen

This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following proce­dure.
Menu screen for INPUT 1 or INPUT 2 RGB mode
Menu Bar (Main Menu)

Menu Selections (Adjustments)

1 Press .
The menu screen is displayed.
Note
The “Picture” menu screen for the selected input mode is displayed.
The on-screen display shown on the lower right is displayed when the IN­PUT 1 or 2 mode is selected.
Menu screen for INPUT 3 or INPUT 4 Mode
Menu Bar (Main Menu)
ENTER button
''
""
\\
",
""
\,
\\
||
|
||
',
''
buttons
MENU button
-42
ENTER button
""
"Menu Screen
""
MENU button
''
""
\\
",
""
\,
\\
||
|
||
',
''
buttons
2 Press
\\
\ or
\\
||
| to select the
||
menu you want to adjust.
Note
For details on the menus, see the tree charts on pages 40 and 41.
''
3 Press
""
' or
" to select the item
''
""
you want to adjust.
Note
To display a single adjustment item, press
Only the menu bar and the selected adjustment item will be displayed. Then if you press ' or ", the fol­lowing item (“Red” is after Bright”) will be displayed.
after selecting the item.
||
|
||
Press
screen.
4 Press
to return to the previous
\\
||
\ or
| to adjust the item
\\
||
selected.
The adjustment is stored.
5 Press .
The menu screen will disappear.
Basic Operation
-43
Using the Menu Screen

Menu Selections (Settings)

1 Press .
The menu screen is displayed.
Note
The “Picture menu screen for the selected input mode is displayed.
The on-screen display shown on the lower right is displayed when INPUT 1 or 2 mode is selected.
2 Press
\\
\ or
\\
menu you want to adjust.
Note
For details on the menus, see the tree charts on pages 40 and 41.
3 Press
''
' or
''
item you want to set.
||
| to select the
||
""
" to select the
""
ENTER button
Menu screen
ENTER button
''
""
\\
",
""
""
",
""
\,
\\
\\
\,
\\
||
|
||
||
|
||
',
''
buttons
MENU button
MENU button
''
',
''
buttons
Note
Press
screen.
In some menus, select the icon us­ing ”.
-44
to return to the previous
Sub menu
4 Press
The cursor shifts to the sub menu.
5 Press
ting of the item displayed in the sub menu.
||
|.
||
''
""
' or
" to select the set-
''
""
Sub menu
Basic Operation
6 Press
The item selected is set.
Some adjustment items will display
a confirmation message. When setting an item, press \ or | to select “Yes or OK and then press
.
Note
.
7 Press .
The menu will disappear.
-45

Adjusting the Picture

You can adjust the projector’s picture to your preferences with the following picture settings.
Selected Item Description
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
For adjusting the contrast level
For adjusting the brightness of an image
For adjusting the color intensity of the image
For adjusting the tones of an image
For making sharper or softer the contour of an image
For adjusting the redness level
For adjusting the blue level
For adjusting the color temperature of an image

Adjusting Image Preferences

Adjust the “Picture” menu on the menu screen.
For operating the menu screen, see pages 42 to 45.
Note
“Color, Tint and Sharp are not displayed when selecting INPUT 1 or 2 and the Sig­nal Type is “RGB”.
The picture adjustments can be stored separately in each input mode.
When the signal type in INPUT 1 or 2 has been set to Component, Sharp can be adjusted when 480I, 480P, 540P, 580I, 580P, 720P, 1035I or 1080I signals are connected.
To reset all adjustment items, select “Re- set and press
“Red, Blue and CLR Temp cannot be adjusted when Color Selected on the C.M.S. menu is set to sRGB”.
.
\ button | button
For less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
For weaker red
For weaker blue Decreases color
temperature for warmer, reddish, incandescent­like images.
For more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
For stronger red
For stronger blue Increases color
temperature for cooler, bluish, fluorescent-like images.

Selecting the Signal Type

This function allows you to select the input sig­nal type RGB or Component for INPUT 1 or 2.
Select “Signal Type” in the “Picture” menu on the menu screen.
For operating the menu screen, see pages 42 to 45.
Note
RGB Set when RGB signals are received.
Component
Set when Component signals are received.
-46

Progressive Mode

This function allows you to select the progres­sive display of a video signal. The progres­sive display projects a smoother video image.
Select “Progressive Mode” in the “Pic­ture” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
2D Progressive
This function is useful to display fast­moving images such as sports and ac­tion films. This mode optimizes the im­age in a displayed frame.
3D Progressive
This function is useful to display relatively slow-moving images such as drama and documentary more clearly. This mode optimizes the image by esti­mating the movement of a number of pre­ceding and succeeding frames.
Film Mode
Reproduces the image of film source clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhance­ment to progressive mode images. * The film source is a digital video record-
ing with the original encoded as is at 24 frames/second. The projector can con­vert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.
Basic Operation
When using progressive inputs, these
inputs are directly displayed therefore 2D Progressive, 3D Progressive and Film Mode cannot be selected. These modes can be selected in interlace signals other than 1080
In NTSC or PAL60Hz, even if the 3D Pro-
gressive mode has been set, the three­two pull down enhancement will be en­abled automatically, when the film source has been entered.
In PAL50Hz or SECAM, the two-two pull
down enhancement will be enabled only in the Film Mode, when the film source has been entered.
I.
-47

Adjusting Computer Images

Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.
Selected Item Description
Clock
Phase
H-Pos
V-Pos

Computer Image Adjustment

When Auto Sync is set to OFF or when ver­tical stripes or flickering occur in portions of the screen even if Auto Sync is set to Nor­mal or High Speed, adjust Clock” , Phase, H-Pos or V-Pos to obtain the best computer image.
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
Select “Clock”, “Phase”, “H-Pos” or “V- Pos in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Computer image adjustments can be made easily by pressing
details.
. See page 50 for

Saving Adjustment Settings

This projector allows you to store up to seven adjustment settings for use with various com­puters.
Select “Save Setting” in the “Fine Sync” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-48

Selecting Adjustment Settings

Adjustment settings stored in the projector can be easily accessed.
Select Select Setting in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
If a memory has not been set, a resolu­tion and frequency setting will not be dis­played.
When selecting a stored adjustment set­ting with Select Setting, you can set the projector in the stored adjustments.

Special Mode Settings

Ordinarily, the type of input signal is detected and the correct resolution mode is automati­cally selected. However, for some signals, the optimal resolution mode in Special Modes on the Fine Sync menu screen may need to be selected to match the computer display mode.
Set the resolution by selecting Special Modes in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Basic Operation
Note
Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)
When a DVD player or Digital Video is con­nected, select 480P as the input signal. See “Checking the Input Signal below for infor-
mation on the currently selected input signal.

Checking the Input Signal

This function allows you to check the current input signal information.
Select Signal Info in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
The projector will display the number of scanned lines available from audio-visual equipment such as a DVD player or Digi­tal Video.
-49
Adjusting Computer Images

Auto Sync Adjustment

Used to automatically adjust a computer image.
Select Auto Sync in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
When setting to Normal or
High Speed”:
Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a com­puter.
Manual adjustments should be per­formed:
When the optimum image cannot be achieved with Auto Sync adjustment. See page 48.
Auto Sync adjustment may take some time to complete, depending on the im­age of the computer connected to the pro­jector.
When setting Auto Sync to OFF orHigh Speed, and if
Sync will be executed in High Speed mode. If the button is pressed again within one minute, Auto Sync will be ex­ecuted in Normal mode.
is pressed Auto
Screen display during Auto Sync
AUTO SYNC button

Auto Sync Display Function

Used to set the screen displayed during Auto Sync.
Select Auto Sync Disp in the Fine Sync menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
..... The image set as a background
image is projected.
..... The computer image being ad-
justed is displayed.
-50

Easy to Use Functions

Easy to Use Functions

Selecting the Picture Display Mode

This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “FULL”, “DOT BY DOT”, “BORDER”, “STRETCH” or “SMART STRETCH” image.
Switching the Picture Display Using Different Input Signals
Press .
Each time
changes as shown on page 52 and 53.
Info
In the Dot by Dot Mode, images are dis­played in the original resolution, therefore they will not be enlarged.
To return to the standard image, press
while “RESIZE” is displayed on the screen.
COMPUTER
4:3 aspect ratio
Other aspect ratios
“NORMAL” is fixed when XGA (1024 × 768) signals are entered.
is pressed, the display
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1280 × 960)
UXGA (1600 × 1200)
SXGA (1280 × 1024)
Input Signal
while maintaining the aspect ratio.
NORMAL
1024 × 768
1024 × 768
1024 × 768
1024 × 768
960 × 768
NORMAL
Projects a full screen image
RESIZE button
Screen display of the picture display mode
FULL
1024 × 768
Output screen image
FULL
Projects a full screen image
while ignoring the aspect ratio.
DOT BY DOT
800 × 600
1280 × 960
1600 × 1200
1280 × 1024
DOT BY DOT
Projects the original resolution
signal of the image.
Resolution lower than
XGA
XGA
Resolution higher than
XGA
SXGA (1280 × 1024)
-52
4:3 aspect ratio
4:3 aspect ratio
4:3 aspect ratio
VIDEO
480I, 480P, 580I, 580P,
NTSC, PAL, SECAM
540P
720P, 1035I, 1080I
4:3 aspect ratio.
Letter box, squeeze
16:9 aspect ratio
16:9 aspect ratio
1024 × 768
STRETCH is fixed when 720P, 1035I or 1080I signals are entered.
* The Digital Shift function can be used with these images.
NORMAL
Input Signal
4:3 aspect ratio
480I, 480P,
580I, 580P,
NTSC, PAL, SECAM
Letter box
Squeeze
NORMAL
Projects a full screen image.
FULL
1024 × 768
FULL
Projects the center part in a 4:3
screen by enlarging 1.3 times
toward the horizontal direction.
BORDER
768 × 576*
Output screen image
BORDER
Projects 4:3 image fully in
STRETCH (the following
column) image.
STRETCH
1024 × 576*
STRETCH
Projects 16:9 image evenly
over entire screen
(top/bottom black bands).
SMART STRETCH
1024 × 576*
SMART STRETCH
Projects the image fully in a
16:9 screen by enlarging only
the surrounding areas while
keeping the aspect ratio in
the middle part of the image
at 4:3.
540P
720P, 1035I, 1080I
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in
16:9 screen)
16:9 aspect ratio
Easy to Use Functions
-53

Displaying a Still Image

This function allows you to instantly freeze a moving image. This is useful when you want to display a still image from a computer or video, giving you more time to explain the image to the audience.
Freezing a Moving Image
1 Press .
The projected image is frozen.
FREEZE button
2 Press again to return to the
moving image from the cur­rently connected device.
"On-screen Display
54
-54

Enlarging a Specific Portion of an Image

This function allows you to enlarge a specific portion of an image. This is useful when you want to display a detailed portion of the image.
Displaying an Enlarged Portion of an Image
1 Press .
Enlarges the image.
Pressing or
duces the projected image.
enlarges or re-
',",\,|
buttons
Note
To enlarge
×1 ×4 ×9 ×16 ×36 ×64×2 ×3
To reduce
You can change the location of the
enlarged image using ', ", \ and |.
When an image with a resolution higher than SXGA is displayed, ×2 and ×3 cannot be selected.
2 Press
to cancel the opera­tion, then the magnification returns to ×1.
Note
In the following cases, the image will return to the normal size (×1).
When switching the INPUT mode.
When
When the input signal is changed.
When the input signal resolution
and refresh rate (vertical frequency) change.
has been pressed.
"On-screen Display
ENLARGE (Enlarge/ Reduce) buttons
Easy to Use Functions
-55

Gamma Correction Function

Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. When you are displaying images with frequent dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the impression of greater depth in the image.
Selected Mode
STANDARD
PRESENTATION
CINEMA
CUSTOM
For Standard picture
Brightens darker portions of image for more enhanced presentations.
Gives greater depth to darker portions of image for a more exciting theater experience.
Allows you to adjust gamma value using Sharp Advanced Presentation Software.
Adjusting Gamma Correction
1 Press .
Each time
level toggles between the different types of gamma modes.
is pressed, the gamma
2 To return to the default settings,
press
displayed.
The Gamma mode does not oper­ate for INPUT 1 or INPUT 2 when Color Selected on the C.M.S. menu is set to sRGB”.
when “GAMMA” is
Note
Description
UNDO button
GAMMA button
STANDARD CUSTOM
56
PRESENTATION CINEMA
-56

Displaying Dual Pictures (Pict in Pict)

Picture in Picture function allows you to display two pictures on the same screen. You can display the image input from INPUT 3 or 4 as an inset picture overlapping the main picture from INPUT 1 or 2.
Displaying the Inset Picture
UNDO button
1 Press
.
ENTER button
2 Press
control or
or
on the remote
on the projector
to switch the image in the in­set picture .
3 Press
',
''
",
""
\\
\ and
\\
||
| to set the
||
''
""
position of the inset picture.
Press
ing or to make the frame disappear.
4 Press
to stop the frame from mov-
to move the inset pic-
ture.
The inset picture will be moved to the inset picture frame.
Note
The inset picture can only be displayed with composite video (NTSC/PAL/ SECAM) or S-Video signal.
The Freeze function works only with the inset picture, when the Pict in Pict mode is in operation.
When the signal entered into INPUT 1 or 2 is as follows, Pict in Pict does not work:
With a resolution that exceeds SXGA.
When the input signal is 480
540P, 580
When the input signal has changed to
the Interlace mode using RGB signals.
When the picture display mode is set to
DOT BY DOT.
When no signals are sent to INPUT 1 or
2, or when the resolution or refresh rate (vertical frequency) is changed.
I, 580P, 720P, 1035I or 1080I.
I, 480P,
', ", \, | buttons
PinP button
INPUT 3/4 buttons
Easy to Use Functions
-57

Black Screen Function

This function can be used to display a black screen.
Blacking out the Pro­jected Image
1 Press .
The screen turns black and “BLACK SCREEN is displayed on the screen.
2 To return to the original
projected image, press again.
BLACK SCREEN button
" Projected Image
58
-58

Displaying the Break Timer

This function can be used to show the remaining time for break during meeting.
Displaying and Setting the Break Timer
1 Press . The break timer
starts to count down from 5 minutes.
2 When
''
' ,
''
""
" ,
""
is displayed, press
\\
||
\ or
| to set the break
\\
||
timer.
You can set anywhere between 1 and 60 minutes (in 1 minute units).
The break timer starts to count down as soon as ' , " , \ or | is pressed.
BREAK TIMER button
', ", \, |
buttons
3 Press
to cancel the break
timer.
Note
Auto Power Off function will be temporarily disabled during the break timer. When no input signal is detected for more than 15 minutes, the projector will auto­matically enter the standby mode if the break timer has elapsed.
The break timer will be displayed on the startup image. To change the screen dis­played during the break timer, change the setting of Startup Image (see page 68).
"On-screen Display
Easy to Use Functions
-59

Color Management System (C. M. S.)

This function allows you individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) .

Selecting the Color Reproduction Mode

Select “Color Selected” in the “C.M.S.” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
For additional information about sRGB function, visit “http://www.srgb.com/”.
“sRGB” cannot be selected for “Color Se­lected” on the C.M.S. menu when “Com­ponent” is selected for “Signal Type” on the “Picture” menu.
When “sRGB” is selected;
The gamma correction cannot be set.
“Red”, “Blue” or “CLR Temp” in “Picture”
cannot be adjusted.
If “Standard” or “sRGB” is selected for “Color Selected”, other items (e.g., Target) cannot be adjusted.
Selected item Standard Custom 1-3
sRGB
Sharp default setting “Lightness”, “Chroma” and “Hue” can
be adjusted for each of the six colors. The mode changes to sRGB
Description
Info
When “sRGB” is selected, the projected image may become dark; however, this does not indicate a malfunction.

Selecting the Target Color

Select “Target in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-60
-60
Red Cyan
Yellow Blue
Green Magenta

Setting the Brightness of the Target Color

Select Lightness in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.

Setting the Chromatic Value of the Target Color

Select Chroma in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.

Setting the Hue of the Target Color

Select Hue in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Easy to Use Functions
-61
Color Management System (C.M.S.)

Resetting User-Defined Color Settings

Select Reset (This Color) or Reset (All Colors) in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.

Overview of All Color Settings

Select View Settings in the C.M.S. menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Selected item
Reset (This Color)
Reset (All Colors)
Description
Lightness, Chroma and “Hue of the color selected for Target are reset.
Lightness, Chroma and Hue of all colors are reset.
-62-62

Setting the Audio Output Type

This function allows you to set the audio output type.
Selected Item
FAO (Fixed audio output)
VAO (Variable audio output)
Audio output that does not vary in strength with the volume level of the source projector.
Audio output that varies in strength with the volume level of the source projector.
Description
Setting the Audio Out­put Type
Select Audio Out in the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.

Setting on/off the Internal Speaker

Easy to Use Functions
This function allows you to set on/off the internal speaker.
Setting on/off the Inter­nal Speaker
Select Speaker in the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-63

Auto Search Function

This function automatically searches for and switches to the input mode in which signals are being received, when the projector is turned on, or when the INPUT button is pressed.
Using Auto Search
Select Auto Search in the Options (1) menu on the menu screen.
For operating the menu screen, see pages 42 to 45.
Note
ON Automatically switches to the input mode in which signals are being received, when turning on the projector or pressing
the projector.
OFF For switching input modes manually in order by pressing
To stop searching for the input mode,
press
or on the remote control.
on the projector, or , ,
on the projector.
on
Info
Even while this function is searching for
input signals, whenever
on the remote control is pressed, the
input mode is switched to the respective one.
Even while the function is searching for input signals, pressing
tor returns to the previous input mode.
-64
-64
, , or
on the projec-

Video Digital Noise Reduction (DNR) System

Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Reducing Image Noise
Select “DNR” in the “Options (1)” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Set a level so as to view a clearer picture.
Make sure to set DNR to OFF in the fol­lowing cases:
When the image is blurry.
When the contours and colors of moving
images drag.
When TV broadcasts with weak signals are projected.
Info
This function is available with INPUT 1, 2 (480I, 480P, 580I and 580P signals) and INPUT 3, 4 (all signals).

Setting On-screen Display

This function allows you to turn on or off the on-screen messages. When setting Level A or Level B in OSD Display, the input mode display (e.g. INPUT 1) will not appear, even if the INPUT button is pressed.
Selected Item
Normal
Level A
Level B
All On-screen Displays are displayed.
Input/Freeze/Enlarge/Auto Sync/Volume/Mute/Black Screen are not displayed.
All On-screen Displays are not displayed. (except Menu, On-Screen Displays displayed when the KEYSTONE button is pressed, and warning displays (Temp./Change The Lamp., etc.))
Turning Off the On-screen Display
Description
Easy to Use Functions
Select OSD Display in the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
-65

Setting the Video System

The video input system mode is preset to Auto; however, a clear picture from the con­nected audio-visual equipment may not be received, depending on the video signal differ­ence. In that case, switch the video signal.
Setting the Video System
Select Video System in the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
The video signal can only be set in IN­PUT 3 or INPUT 4 mode.
In “Auto, images are displayed in PAL even if PAL-N or PAL-M input signals are received.
PAL SECAM
NTSC4.43
NTSC3.58
When connected to PAL video equipment. When connected to SECAM video
equipment. When reproducing NTSC signals in
PAL video equipment. When connected to NTSC video equipment.
-66
-66

Saving Projected Images

This projector allows you to capture projected images (RGB signals) and set them as a startup image, or background image when no signals are being received.
You can capture the images that are input using RGB signals.

Capturing the Image

Select “Image Capture” in the “Options (1)” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
1 Press
The projected image is captured. It may take some time for capturing.
11
2
1 Press
11
22
2 Press
22
Note
Only images from XGA (1024 × 768) non­interlace signals in INPUT 1 or INPUT 2 mode can be captured.
The saved image is reduced to 256 colors.
Images from equipment connected to
INPUT 3 or INPUT 4 terminal cannot be captured.
Only one image can be captured and saved.
The color of images may differ before and after saving if an image is captured on which image adjustment has been per­formed using the “C.M.S.” function.
''
' or
''
Save Image” and press
“Yes”.
""
" to select
""
\\
\ or
\\
||
| to select
||
.
.
Easy to Use Functions

Deleting the Captured Image

1
Select “ Delete” and press
11
2
1 Press
11 22
2 Press
22
\\
||
\ or
| to select “OK”.
\\
||
.
.
-67

Setting a Background Image

This function allows you to select the image displayed when no signal is being sent to the projector.
Selected Item
Sharp
Custom
Blue
None
*1 You can set a captured image as a background image by selecting Custom”. *2 If the input signal has interference, the screen will be displayed with the interference.
*1
SHARP default image
User customized image (e.g. company logo)
Blue screen
Black screen
*2
Description
Selecting a Background Image
Select Background in the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
When “Custom is selected, an image saved using Image Capture can be dis­played as a background image. A “Custom image is preset as a black screen.

Selecting a Startup Image

This function allows you to specify the image to be displayed upon the projectors startup.
Selected Item
Sharp
Custom *
None
* You can set a captured image as a startup image by selecting Custom”.
SHARP default image
User customized image (e.g. company logo)
Black screen
Selecting a Startup Image
Select Startup Image in the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
When “Custom is selected, an image saved using Image Capture can be dis­played as a startup image. A “Custom image is preset as a black screen.
68
-68
Description

Selecting the Economy Mode

These functions allow you to reduce the power consumption of the projector.

Setting the Power Save Mode

Select Power Save in Economy Mode under the Options (1) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
Although lamp life and noise are improved when Power Save is set to ON, bright­ness decreases by 20%.
Power Save mode is factory preset toOFF”.
Status
ON (Low power mode)
OFF (Standard mode)
Brightness
80%
100%
Power consumption (When using
AC 100V)
325 W
400 W
Lamp Life
3,000 hours
2,000 hours

Monitor Out/RS-232C Off Function

This projector consumes power when using a monitor connected to the OUTPUT (INPUT 1,
2) terminal and a computer connected to the RS-232C terminal. When not using these ter­minals, Mntr.out/RS232 can be set to OFF to reduce standby power consumption.
Select Mode under the Options (1) menu the menu screen. For operating the menu screen, see pages 42 to 45.
Mntr.out/RS232
ON
OFF
Set “Mntr.out/RS232 to ON when using the Sharp Advanced Presentation Software.
Monitor Out/RS-232C connection is set to ON”.
Monitor Out/RS-232C connection is set to OFF”.
Note
in “Economy
on
Easy to Use Functions
-69
Selecting the Economy Mode

Auto Power Off Function

When no input signal is detected for more than 15 minutes, the projector will automatically enter the standby mode if set to ON”. The Auto Power Off function will be disabled when it has been set to OFF”.
Select Auto Power Off in Economy Mode under the Options (1) the menu screen. For operating the menu screen, see pages 42 to 45.
Note
When the Auto Power Off function is set to ON, 5 minutes before the projector enters the standby mode, the message Enter STANDBY mode in X min. will appear on the screen to indicate the remaining minutes.
menu on

Displaying the Remaining Lamp Life (Percentage)

Checking the Remaining Lamp Life (Percentage)
This function allows you to check the remain­ing lamp life (percentage).
Select the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
It is recommended that the lamp be changed when the remaining lamp life becomes 5%. For lamp replacement, contact your nearest Sharp Authorized Projector Dealer or Service Center.
The table at the right indicates rough esti­mates in the case of using only in each mode shown. Remaining lamp life changes within the range of the values shown depending on the frequency at which Power Save is switched ON and OFF” (see page 69).
-70
-70
-70
Used with only ON on Power Save (Low power mode)
Used with only OFF on Power Save (Standard mode)
3,000 hours 150 hours
2,000 hours 100 hours
Remaining Lamp Life (Percentage)
Remaining lamp life 100% 5%

Reversing/Inverting Projected Images

This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications.
Selected Item
Front
Ceiling + Front
Rear
Ceiling + Rear
Normal image
Inverted image
Reversed image
Reversed and inverted image
Setting the Projection Mode
Select “PRJ Mode” in the “Options (2)” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
If a password has been set, the password input box will be displayed when select­ing the “PRJ Mode”.
This function is used for the reversed im­age and ceiling-mount setups. See page
32 for these setups.
Description
Front Ceiling+Front Rear Ceiling+Rear

Locking the Operation Buttons on the Projector

This function can be used to lock the use of certain operation buttons on the projector. The following are the three keylock levels.
Keylock Level
Normal
Level A
Level B
All operation buttons are functional.
Only INPUT/VOLUME buttons on the projector are available.
All operation buttons on the projector are unavailable.

Setting up the Keylock

Select “Keylock Level” in the “Options (2)” menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
If a password has been set, the password input box will be displayed when select­ing the Keylock Level”.
Description
Easy to Use Functions
-71
Locking the Operation Buttons on the Projector

Canceling the Keylock Setting

When the Keylock Level is set to Normal”, all buttons are functional.
Select Keylock Level in the Options (2) menu on the menu screen and set Normal For operating the menu screen, see pages 42 to 45.
When a password has been set, and
Keylock Level is selected, the password input box will be displayed.
If both a password and the Keylock Level have been set at the same time, the pass­word will be necessary before changing the Keylock Level.
.
Note

Selecting the Transmission Speed (RS-232C)

This menu allows you to adjust the transmission speed of the RS-232C connection by select­ing the baud rate.
Selecting the Transmis­sion Speed (RS-232C)
Select RS-232C in the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
When a password has been set, and “RS- 232C is selected, the password input box will be displayed.
Make sure that both the projector and computer are set for the same baud rate. Refer to the computers operation manual for instructions for setting the computer’s baud rate.
-72
-72

Setting up a Password

A password can be set by the user to prevent adjustments to certain settings on the Options (2) menu. Using a password together with the Keylock Level (page 71) is more effective.

Entering the Password

Select Password in the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
''
1 Press
sired number and then press
||
|.
||
""
' or
" to select the de-
''
""
2 Enter the 3 remaining digits
and press
.
3 Enter the password again in
Reconfirm and press
Note
When a password is set, you need to enter the password to change PRJ Mode, Keylock Level, RS­232C, Anti-Theft and All Reset settings.
.
Easy to Use Functions
-73
Setting up a Password

Changing the Password

Select Password in the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
''
1 Press
',
''
""
" and
""
||
| to enter the
||
password in Old Password and press
2 Press
''
',
''
new password and press
.
""
" and
""
||
| to set the
||
.
3 Enter the new 4-digit password
again in Reconfirm and press
.
Note
If you do not want to set a password, leave the fields in procedures 2 and 3 blank and press
To cancel the password settings, click
.
.

If You Forget Your Password

If you forget the password, delete it and set a new password using the following procedure.
ON ON
Press
ON
-74
-74

Setting the Anti-Theft

The anti-theft function prevents unauthorized use of the projector. You can choose to use this function or not. If you do not want to use this function, just do not enter the keycode. Once the anti-theft function is activated, users will need to enter the correct keycode each time the projector is turned on. Failure to enter the correct keycode will cause images not to be projected. The following procedures explain how to use this function.

Entering the Keycode

Anti-Theft cannot be selected unlessPassword is set. (See page 73.)
When “Anti-Theft is selected, the password input box will appear. Enter the keycode af­ter the right password is entered.
Select Anti-Theft in the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Info
Once the function is activated, you must
remember the correct keycode. We sug­gest you record the keycode in a safe place where only authorized users have access. If you lose or forget your keycode, you will need to contact your nearest Sharp Authorized Projector Dealer or Ser­vice Center (see page 96). You may need to bring your projector to them to restore the projector to original factory condition (password and keycode reset).
1 Press any button you like on
the remote control or projec­tor to set the first digit in “New Code”.
Note
The following buttons on the remote control and projector cannot be set as keycodes:
ON button
STANDBY button
ENTER button
UNDO button
MENU button
FORWARD button
BACK button
Easy to Use Functions
-75
Setting the Anti-Theft
2 Enter the remaining 3 digits by
pressing any buttons you like.
3 Enter the same keycode once
more in Reconfirm”.
Note
The Keylock function will become temporarily disabled.
When Anti-Theft is set, the keycode inputting box appears after the power is turned on. When it appears, enter the right keycode.
Press the buttons on the remote control if the buttons on the remote control are used for setting the keycode. In the same manner, press the buttons on the projector if the buttons on the projector are used for setting the keycode.

Changing the Keycode

When “Anti-Theft is selected, the password input box is displayed. After the password has been entered, you can change the keycode.
Select Anti-Theft in the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
1 Press the buttons on the re-
mote control or the projector to enter the preset 4-digit keycode in Old Code”.
2
Press any button you like on the remote control or the pro­jector to enter the new keycode.
3 Enter the same 4-digit keycode
in “Reconfirm”.
Note
If you do not want to set a keycode, leave
the keycode field blank in steps 2 and 3 and press
.
-76-76

Initializing the Settings

This function allows you to initialize the settings you have made in the projector.
Returning to the Default Settings
Select All Reset in the Options (2) menu on the menu screen. For operating the menu screen, see pages 42 to 45.
Note
If a password has been set, the pass-
word input box will be displayed when selecting All Reset”.
The following items cannot be initialized.
C. M. S.
Lightness”, “Chroma and Hue
respectively saved for Custom 1-3 on the C.M.S. menu.
Fine Sync
Special Modes
Signal Info
Options
Lamp Life
Anti-Theft
Language
Image stored using Image Capture
Easy to Use Functions
-77

Displaying the Adjustment Settings

This function can be used to display all the adjusted settings as a list on the screen.
Overview of All Menu Settings
Select the “Status” menu on the menu screen and press
For operating the menu screen, see pages 42 to 45.
.
-78
-78

Appendix

Maintenance

Cleaning the projector
Be sure to unplug the power cord before clean-
ing the projector.
The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides
on the projector. Do not attach rubber or plastic items on the pro­jector for long time.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the projector.
Thinner
Wax
Wipe off dirt gently with a soft flannel cloth.
N
e
u
tra
l d
e
te
rg
e
n
t
Cleaning the lens
Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coat­ing film on the surface of the lens.
As the surface of the lens can easily get dam­aged, be sure not to scrape or hit the lens.
Cleaning
Paper
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Neutral detergent diluted with water
When the dirt is hard to remove, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before using.
-80

Replacing the Air Filter

M4
M4
M4
M4
• This projector is equipped with air fil-
ters to ensure the optimal operating condition of the projector.
• The air filters should be cleaned ev-
ery 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location.
• Ask your nearest Sharp Authorized
Projector Dealer or Service Center to exchange the filter (PFILDA005WJZZ) when it is no longer possible to clean.
Cleaning and replacing the bottom air filter
Air filter (not removable)
STANDBY button
Air filter
1 Press
or
on the remote control to
on the projector
STANDBY
put the projector into the standby mode.
Wait until the cooling fan stops.
2 Disconnect the power cord.
Unplug the power cord from the AC socket.
3 Remove the bottom filter cover.
Turn over the projector. Grab the tab and slide open the filter cover in the direction of the arrow.
STANDBY button
AC socket
Tab
4 Remove the air filter.
Pick the air filter up with your fingers and lift it out of the filter cover.
-81
Replacing the Air Filter
5 Clean the air filter.
Clean the dust off the air filter and cover with a vacuum cleaner extension hose.
6 Replace the air filter.
Place the air filter underneath the tabs on the filter cover.
7 Replace the filter cover.
Slide the filter cover in the direction of the arrow to close it.
Note
Be sure the filter cover is securely installed. The power will not turn on unless it is correctly installed.
If dust or dirt has collected inside the bottom air filter (not removable), clean the filter with a vacuum cleaner extension hose.
-82

Maintenance Indicators

The warning lights on the projector indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
About the lamp indicator
Power indicator
Lamp indicator
Temperature warning
indicator
About the temperature warning indicator
If the temperature inside the pro­jector increases, due to blockage of the air vents, or the setting lo­cation, “ lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the tem­perature warning indicator will blink, the cooling fan will run for further 90 seconds, then the pro­jector will enter the standby mode. After “ perform the following measures.
” will blink in the
” appears, be sure to
The lamp life becomes 0%, when used for approximately 3,000 hours with “ON” in “Power Save” or when used for approxi­mately 2,000 hours with “OFF” in “Power Save” (see page 69).
When the remaining lamp life becomes 5% or less, “
” will be displayed on the screen in yellow. When the percentage becomes 0%, “
” will change to “ ” (red), the lamp will automatically turn off and then the projector will automatically enter the standby mode. At this time, the lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the pro­jector will not turn on.
Maintenance indicator Condition
Abnormal
Abnormal
Red on/ Standby
Red blinks Red on
Red on/ Standby
Red blinks
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Normal
Off
Green on
Green blinks
when the
lamp is
warming up
or shutting
down.
Green on/ Red on
The internal temperature is abnormally high.
/
Time to change the lamp
The lamp does not illuminate.
The power indicator blinks in red when the projector is on.
Problem Possible Solution
Blocked air intake
Cooling fan break-
down
Internal circuit failure
Clogged air intake
Remaining lamp life
becomes 5% or under.
Burnt-out lamp
Lamp circuit failure
The filter cover, lamp
unit cover or lens cover is open.
Relocate the projector to an area with proper ventilation.
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 96) for repair.
Carefully replace the lamp. (See page 86)
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 96) for repair.
Please exercise care when replacing the lamp.
Securely install the covers.
If the power indicator blinks even
when the filter cover is securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center for advice.
-83
Maintenance Indicators
Info
If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the pos­sible solutions on the previous page and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.)
If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
If you want to clean the air vents during projector operation, be sure to put the projector into the standby mode. After the cooling fan has stopped, clean the vents.
Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.
-84

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be-
comes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 70.
For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho­rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp indicator and on-screen display icon are illuminated or flash, it is recommended that
the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult with a doctor as soon as possible.
Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to remove the damaged lamp and assure safe operation.
U.S.A. ONLY

Replacing the Lamp

Caution
Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.
If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho-
rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC­XGC55X//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully change the lamp by following the instructions described in this section. If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
-85
Regarding the Lamp
Removing and Install­ing the Lamp Unit
Info
Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector.
To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
Do not loosen other screws except for the lamp unit cover and lamp unit. (Only the silver screws are loosened).
Please refer to the installation manual included with the lamp unit.
Lamp unit
STANDBY button
BQC-XGC55X//1
1 Press
or
on the remote control to
on the projector
STANDBY
put the projector into the standby mode.
Wait until the cooling fan stops.
Warning!
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.
2 Disconnect the power cord.
Unplug the power cord from the AC socket.
Leave the lamp until it has fully cooled down (about 1 hour).
3 Change the air filter.
Change the air filter whenever you in­stall the lamp unit (see pages 81 and
82).
4 Remove the lamp unit cover.
Loosen the user service screw that secures the lamp unit cover. Then open the cover in the direction of the arrow.
STANDBY button
AC socket
User service screw
-86
5 Remove the lamp unit.
Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow.
6 Insert the new lamp unit.
Press the lamp unit firmly into the lamp unit compartment. Fasten the secur­ing screws.
7 Attach the lamp unit cover.
Insert the tab of the lamp unit cover into the opening, and press the cover until it clicks in place.
Securing screw
Info
If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.
1 Connect the power cord.
Plug the power cord into the AC socket of the projector.
2 Reset the lamp timer.
While pressing simultaneously
and
on the projector.
“LAMP 100% is displayed, indicating that the lamp timer is reset.
on the projector, press
,
ON
INPUT button
ON button
User service screw
AC socket
ENTER button
Info
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.
UNDO button
-87

Connecting Pin Assignments

INPUT 1/2 RGB and OUTPUT Signal Terminal: 15-pin Mini D-sub female connector
RGB Input
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Reserve input 1
5. Not connected
5 10 15
1 6 11
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. GND
12. Bi-directional data
13. Horizontal sync (Composite sync)
14. Vertical sync signal
15. Data clock
RS-232C Terminal: 9-pin Mini DIN female connector
Pin No. Signal Name I/O Reference
1 Output Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Input Not connected 5 SG Signal Ground Connected to internal circuit 6 Input Not connected 7 RS Output Connected to Pin 8 8 CS Input Connected to Pin 7 9 Output Not connected
Pin No. Signal Name I/O Reference
1 CD Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 ER Not connected 5 SG Signal Ground Connected to internal circuit 6 Not connected 7 RS Connected to internal circuit 8 CS Connected to internal circuit 9 CI Not connected
9
6
5
15
8
21
69
7
3
4
9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
Component Input
1. PR (CR)
2. Y
3. P
(CB)
B
4. Not connected
5. Not connected
6. Earth (P
7. Earth (Y)
8. Earth (P
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
)
R
)
B
Note
Pin 8(CS) and Pin 7(RS) are short circuited inside the projector.
RS-232C Cable recommended connection: 9-pin D-sub female connector
51
96
Pin No. Signal Pin No. Signal
1CD 1 CD 2RD 2 RD 3SD 3 SD 4ER 4 ER 5SG 5 SG 6DR 6 DR 7RS 7 RS 8CS 8 CS 9CI 9 CI
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling
device (e.g. PC).
Projector
Pin No.
4 5 6
PC
Pin No.
4 5 6
-88

(RS-232C) Specifications and Command Settings

PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 22 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: 9,600 bps Stop bit: 1 bit Data length: 8 bits Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projec­tor processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Response code format
Normal response
O K E R R
Command 4-digit Parameter 4-digit
Problem response (communication error or incorrect command)
Return code (0DH)
Return code (
0DH)
Info
When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.
To conserve power in STANDBY mode, the CPU in this model will enter Deep Sleep mode approximately 10 seconds after the
last command is received. In the case of transmitting commands during Deep Sleep mode, it takes a maximum of 30 seconds
until the response code is received. If subsequent commands are sent to the projector within 10 seconds, the projector will
reply immediately. If no further commands are received within 10 seconds, the projector will again return to Deep Sleep mode. Please note that Deep Sleep mode is only activated in STANDBY mode. There is no delayed RS-232C response when the
projector is in operation.
Special commands, “POWR????” and “TLPS
_ _ _
1” are available for applications that require continuous polling. These
commands will not wake the CPU in Deep Sleep mode and the projector will provide immediate reply in STANDBY mode. “1”
will indicate Power on, “0” will indicate STANDBY mode. When the power is turned on during standby with the “POWER ON”
command, wait for at least 40 seconds after the power has been turned on, and then transmit the next command.
We suggest disabling the AUTO SEARCH feature before initiating RS-232C communications. If AUTO SEARCH is enabled, it will be necessary to send the STANDBY mode command “POWR_ _ _0” two times to power down the projector. (The first “POWR_ _ _0” command cancels AUTO SEARCH and the second “POWR_ _ _0” command will put the projector into the standby mode.)
Note
Do not repeatedly or periodically send any commands other than POWR????” and TLPS_ _ _1 in STANDBY mode as it will cause problems.
When the projector is put into the standby mode, a message Shutting Down. Please Wait.” is displayed for about 20 seconds. At that time, if the POWR_ _ _1” command is being sent, ERR will be returned and this command is not received.
When using the computer control function of the projector, the adjustment values cannot be read by the computer. Therefore, confirm the values by transmitting the display commands (e.g. “RARE_ _ _0”) for each adjustment menu and checking the values with the on-screen display. If the projector receives adjustment/setting commands other than menu display commands, it will execute the commands without displaying the on-screen display.
Commands
Example:
When BRIGHT of INPUT 1 image adjustment is set to –10.
ProjectorComputer
OK
CONTROL CONTENTS
BLACK SCREEN ON
BLACK SCREEN OFF
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT CHECK
FREEZE ON
FREEZE OFF
AUTO SYNC START
COMMAND
I
M
B
I
M
B
I
R
G
I
R
G
I
V
E
I
V
E
I
C
H
F
R
E
F
R
E
A
D
J
PARAMETER
K
_
K
_
B
_
B
_
D
_
D
_
K
_
Z
_
Z
_
S
_
RETURN
OK OR ERR
_
_
1
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
0
OK OR ERR
_
_
1
RABR 1 0_–
CONTROL CONTENTS
POWER ON
STANDBY
POWER STATUS
LAMP POWER STATUS
VOLUME (0 - 60)
MUTE ON
MUTE OFF
BUTTONS & REMOTE CONTROL KEY
KEYSTONE (–127 - +127)
DIGITAL SHIFT (–96 - +96)
COMMAND
W
O
P
W
O
P
W
O
P
O
P
T
L
O
V
T
U
M
T
U
M
Y
E
K
D
N
L
R
R
R
W
A
E
E
S
S
PARAMETER
_
_
_
_
_
_
?
?
?
_
_
_
*
_
_
_
_
_
_
_
_
*
*
*
*
*
_
RETURN
1
OK OR ERR
0
OK OR ERR
?
0:OFF, 1:ON
0:OFF, 1:ON, 2:COOLING
1
3:SHUTTING DOWN
*
OK OR ERR
1
OK OR ERR
0
OK OR ERR
*
OK OR ERR
*
OK OR ERR
→ ←
BUTTONS & REMOTE CONTROL KEY
Appendix
-89
(RS-232C) Specifications and Command Settings
CONTROL CONTENTS
INPUT 1 RESIZE : NORMAL
INPUT 1 RESIZE : FULL
INPUT 1 RESIZE : DOT BY DOT
INPUT 1 RESIZE : STRETCH
INPUT 1 RESIZE : SMART STRETCH
INPUT 2 RESIZE : NORMAL
INPUT 2 RESIZE : FULL
INPUT 2 RESIZE : DOT BY DOT
INPUT 2 RESIZE : STRETCH
INPUT 2 RESIZE : SMART STRETCH
INPUT 3 RESIZE : NORMAL
INPUT 3 RESIZE : BORDER
INPUT 3 RESIZE : STRETCH
INPUT 3 RESIZE : SMART STRETCH
INPUT 4 RESIZE : NORMAL
INPUT 4 RESIZE : BORDER
INPUT 4 RESIZE : STRETCH
BUTTONS & REMOTE CONTROL KEYPICTURE
INPUT 4 RESIZE : SMART STRETCH
RGB GAMMA : STANDARD
RGB GAMMA : PRESENTATION
RGB GAMMA : CINEMA
RGB GAMMA : CUSTOM
VIDEO GAMMA : STANDARD
VIDEO GAMMA : PRESENTATION
VIDEO GAMMA : CINEMA
VIDEO GAMMA : CUSTOM
INPUT 1 CONTRAST (—30 - +30)
INPUT 1 BRIGHT (—30 - +30)
INPUT 1 RED (—30 - +30)
INPUT 1 BLUE (—30 - +30)
INPUT 1 COLOR (—30 - +30)
INPUT 1 TINT (—30 - +30)
INPUT 1 SHARP (—30 - +30)
INPUT 1 CLR TEMP (—3 - +3)
INPUT 1 DISPLAY
INPUT 1 ADJUSTMENT RESET
INPUT 2 CONTRAST (—30 - +30)
INPUT 2 BRIGHT (—30 - +30)
INPUT 2 RED (—30 - +30)
INPUT 2 BLUE (—30 - +30)
INPUT 2 COLOR (—30 - +30)
INPUT 2 TINT (—30 - +30)
INPUT 2 SHARP (—30 - +30)
INPUT 2 CLR TEMP (—3 - +3)
INPUT 2 DISPLAY
INPUT 2 ADJUSTMENT RESET
INPUT 1 SIGNAL TYPE : RGB
INPUT 1 SIGNAL TYPE : COMPONENT
INPUT 2 SIGNAL TYPE : RGB
INPUT 2 SIGNAL TYPE : COMPONENT
INPUT 1 2D PROGRESSIVE
INPUT 1 3D PROGRESSIVE
INPUT 1 FILM MODE
INPUT 2 2D PROGRESSIVE
INPUT 2 3D PROGRESSIVE
INPUT 2 FILM MODE
INPUT 3 CONTRAST (—30 - +30)
INPUT 3 BRIGHT (—30 - +30)
INPUT 3 RED (—30 - +30)
COMMAND
R
A
S
R
A
S
R
A
S
R
A
S
R
A
S
R
B
S
R
B
S
R
B
S
R
B
S
R
B
S
R
A
S
R
A
S
R
A
S
R
A
S
R
B
S
R
B
S
R
B
S
R
B
S
G
A
M
G
A
M
G
A
M
G
A
M
G
A
M
G
A
M
G
A
M
G
A
M
R
A
P
R
A
B
R
A
R
R
A
B
R
A
C
R
A
T
R
A
S
R
A
C
R
A
R
R
A
R
R
B
P
R
B
B
R
B
R
R
B
B
R
B
C
R
B
T
R
B
S
R
B
C
R
B
R
R
B
R
I
A
S
I
A
S
I
B
S
I
B
S
R
A
I
R
A
I
R
A
I
R
B
I
R
B
I
R
B
I
V
A
P
V
A
B
V
A
R
PARAMETER
R
_
R
_
R
_
R
_
R
_
R
_
R
_
R
_
R
_
R
_
V
_
V
_
V
_
V
_
V
_
V
_
V
_
V
_
R
_
R
_
R
_
R
_
V
_
V
_
V
_
V
_
I
_
R
_
D
_
E
_
O
_
I
_
H
_
T
_
E
_
E
_
I
_
R
_
D
_
E
_
O
_
I
_
H
_
T
_
E
_
E
_
I
_
I
_
I
_
I
_
P
_
P
_
P
_
P
_
P
_
P
_
I
_
R
_
D
_
RETURN CONTROL CONTENTS
OK OR ERR
_
_
1
OK OR ERR
_
_
5
OK OR ERR
_
_
3
OK OR ERR
_
_
2
OK OR ERR
_
_
4
OK OR ERR
_
_
1
OK OR ERR
_
_
5
OK OR ERR
_
_
3
OK OR ERR
_
_
2
OK OR ERR
_
_
4
OK OR ERR
_
_
1
OK OR ERR
_
_
3
OK OR ERR
_
_
2
OK OR ERR
_
_
4
OK OR ERR
_
_
1
OK OR ERR
_
_
3
OK OR ERR
_
_
2
OK OR ERR
_
_
4
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
3
OK OR ERR
_
_
4
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
3
OK OR ERR
_
_
4
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
_
*
*
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
_
*
*
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
*
*
*
OK OR ERR
*
*
*
OK OR ERR
*
*
*
INPUT 3 BLUE (—30 - +30)
INPUT 3 COLOR (—30 - +30)
INPUT 3 TINT (—30 - +30)
INPUT 3 SHARP (—30 - +30)
INPUT 3 CLR TEMP (—3 - +3)
INPUT 3 DISPLAY
INPUT 3 ADJUSTMENT RESET
INPUT 4 CONTRAST (—30 - +30)
INPUT 4 BRIGHT (—30 - +30)
INPUT 4 RED (—30 - +30)
INPUT 4 BLUE (—30 - +30)
INPUT 4 COLOR (—30 - +30)
PICTUREFINE SYNC
INPUT 4 TINT (—30 - +30)
INPUT 4 SHARP (—30 - +30)
INPUT 4 CLR TEMP (—3 - +3)
INPUT 4 DISPLAY
INPUT 4 ADJUSTMENT RESET
INPUT 3 2D PROGRESSIVE
INPUT 3 3D PROGRESSIVE
INPUT 3 FILM MODE
INPUT 4 2D PROGRESSIVE
INPUT 4 3D PROGRESSIVE
INPUT 4 FILM MODE
COLOR SELECTED : STANDARD
COLOR SELECTED : sRGB
COLOR SELECTED : CUSTOM 1
COLOR SELECTED : CUSTOM 2
COLOR SELECTED : CUSTOM 3
TARGET : RED
TARGET : YELLOW
TARGET : GREEN
TARGET : CYAN
C. M. S.
TARGET : BLUE
TARGET : MAGENTA
LIGHTNESS (—30 - +30)
CHROMA (—30 - +30)
HUE (—30 - +30)
Reset (THIS COLOR)
Reset (All COLORS)
CLOCK (—150 - +150)
PHASE (—30 - +30)
H-POSITION (—150 - +150)
V-POSITION (—60 - +60)
RGB INPUT DISPLAY
RGB ADJUSTMENT RESET
*1
SAVE SETTING (1 - 7)
SELECT SETTING (1 - 7)
RGB HORIZONTAL FREQUENCY CHECK
RGB VERTICAL FREQUENCY CHECK
AUTO SYNC OFF
AUTO SYNC : ON (NORMAL)
AUTO SYNC : ON (HIGH SPEED)
AUTO SYNC DISPLAY ON
AUTO SYNC DISPLAY OFF
COMMAND
V
A
B
V
A
C
V
A
T
V
A
S
V
A
C
V
A
R
V
A
R
V
B
P
V
B
B
V
B
R
V
B
B
V
B
C
V
B
T
V
B
S
V
B
C
V
B
R
V
B
R
V
A
I
V
A
I
V
A
I
V
B
I
V
B
I
V
B
I
C
M
C
C
M
C
C
M
C
C
M
C
C
M
C
C
M
T
C
M
T
C
M
T
C
M
T
C
M
T
C
M
T
C
M
S
C
M
S
C
M
S
C
M
R
C
M
R
I
N
C
I
N
P
I
A
H
I
A
V
I
A
R
I
A
R
M
E
M
M
E
M
T
F
R
T
F
R
A
A
D
A
A
D
A
A
D
I
M
A
I
M
A
PARAMETER
E
_
O
_
I
_
H
_
T
_
E
_
E
_
I
_
R
_
D
_
E
_
O
_
I
_
H
_
T
_
E
_
E
_
P
_
P
_
P
_
P
_
P
_
P
_
S
_
S
_
S
_
S
_
S
_
G
_
G
_
G
_
G
_
G
_
G
_
L
_
C
_
H
_
E
_
E
_
L
*
H
_
P
*
P
_
E
_
E
_
S
_
L
_
Q
_
Q
_
J
_
J
_
J
_
S
_
S
_
*
*
*
*
*
*
*
*
_
*
_
_
_
_
*
*
*
*
*
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
_
0
_
1
_
1
_
1
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
_
_
_
_
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
6
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
1
OK OR ERR
2
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
0
OK OR ERR
1
OK OR ERR
*
OK OR ERR
*
kHz (***. * OR _)
1
Hz (***. * OR _)
2
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
1
OK OR ERR
0
RETURN
-90
CONTROL CONTENTS
FAO
VAO
SPEAKER ON
SPEAKER OFF
PICT IN PICT : BOTTOM RIGHT
PICT IN PICT : BOTTOM LEFT
PICT IN PICT : UPPER RIGHT
PICT IN PICT : UPPER LEFT
PICT IN PICT OFF
POWER SAVE: STANDARD
POWER SAVE: LOW POWER
DNR: OFF
DNR: LEVEL 1
DNR: LEVEL 2
DNR: LEVEL 3
AUTO SEARCH: OFF
AUTO SEARCH: ON
OSD DISPLAY NORMAL
OSD DISPLAY LEVEL A
OSD DISPLAY LEVEL B
OPTIONS (1)
BLACK SCREEN DISPLAY ON
BLACK SCREEN DISPLAY OFF
VIDEO SYSTEM SELECTION : AUTO
VIDEO SYSTEM SELECTION : PAL (50/60 Hz)
VIDEO SYSTEM SELECTION : SECAM
VIDEO SYSTEM SELECTION : NTSC4.43
VIDEO SYSTEM SELECTION : NTSC3.58
VIDEO SYSTEM SELECTION : PAL_M
VIDEO SYSTEM SELECTION : PAL_N
BACKGROUND SELECTION : SHARP
BACKGROUND SELECTION : CUSTOM
BACKGROUND SELECTION : BLUE
BACKGROUND SELECTION : NONE
STARTUP IMAGE SELECTION : SHARP
STARTUP IMAGE SELECTION : CUSTOM
STARTUP IMAGE SELECTION : NONE
AUTO POWER OFF : NO USE
AUTO POWER OFF : USE
COMMAND
A
O
U
A
O
U
A
S
P
A
S
P
P
I
N
P
I
N
P
I
N
P
I
N
P
I
N
T
H
M
T
H
M
3
D
N
3
D
N
3
D
N
3
D
N
I
N
S
I
N
S
I
M
D
I
M
D
I
M
D
I
M
B
I
M
B
M
E
S
M
E
S
M
E
S
M
E
S
M
E
S
M
E
S
M
E
S
I
M
B
I
M
B
I
M
B
I
M
B
I
M
S
I
M
S
I
M
S
A
P
O
A
P
O
PARAMETER
T
_
T
_
K
_
K
_
P
_
P
_
P
_
P
_
P
_
D
_
D
_
R
_
R
_
R
_
R
_
E
_
E
_
I
_
I
_
I
_
K
_
K
_
Y
_
Y
_
Y
_
Y
_
Y
_
Y
_
Y
_
G
_
G
_
G
_
G
_
I
_
I
_
I
_
W
_
W
_
RETURN
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
1
OK OR ERR
_
_
0
OK OR ERR
_
1
1
OK OR ERR
_
1
2
OK OR ERR
_
1
3
OK OR ERR
_
1
4
OK OR ERR
_
_
0
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
3
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
0
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
3
OK OR ERR
_
_
4
OK OR ERR
_
_
5
OK OR ERR
_
_
6
OK OR ERR
_
_
7
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
3
OK OR ERR
_
_
4
OK OR ERR
_
_
1
OK OR ERR
_
_
2
OK OR ERR
_
_
3
OK OR ERR
_
_
0
OK OR ERR
_
_
1
CONTROL CONTENTS
LAMP LIFE (PERCENTAGE)
LAMP STATUS
PRJ MODE : REVERSE OFF PRJ MODE : REVERSE ON PRJ MODE : INVERT OFF
OPTIONS (2)LANGUAGE
PRJ MODE : INVERT ON KEYLOCK LEVEL : NORMAL KEYLOCK LEVEL : LEVEL A KEYLOCK LEVEL : LEVEL B LANGUAGE SELECTION : ENGLISH LANGUAGE SELECTION : DEUTSCH LANGUAGE SELECTION : ESPAÑOL LANGUAGE SELECTION : NEDERLANDS LANGUAGE SELECTION : FRANÇAIS LANGUAGE SELECTION : ITALIANO LANGUAGE SELECTION : SVENSKA LANGUAGE SELECTION : LANGUAGE SELECTION : PORTUGUÊS LANGUAGE SELECTION : LANGUAGE SELECTION : MODEL NAME CHECK SERIAL NO. CHECK PROJECTOR NAME SETTING 1
(First four characters) PROJECTOR NAME SETTING 2
(Middle four characters) PROJECTOR NAME SETTING 3
(Last four characters) PROJECTOR NAME CHECK
*2
COMMAND
T
L
T
P
L
T
R
M
I
R
M
I
I
M
I
I
M
I
Y
E
K
Y
E
K
Y
E
K
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
L
E
M
R
N
M
R
N
S
N
J
P
N
J
P
N
J
P
N
J
P
PARAMETER
_
L
_
S
_
E
_
E
_
N
_
N
_
L
_
L
_
L
_
A
_
A
_
A
_
A
_
A
_
A
_
A
_
A
_
A
_
A
_
A
_
D
_
D
*
1
*
2
*
3
_
0
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
_
1
_
_
_
_
_
*
*
*
*
*
*
_
_
RETURN
1
0-100 (INTEGER) 0:OFF, 1:ON, 2:RETRY,
1
3:WAITING, 4:LAMP ERROR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
0
OK OR ERR
1
OK OR ERR
2
OK OR ERR
1
OK OR ERR
2
OK OR ERR
3
OK OR ERR
4
OK OR ERR
5
OK OR ERR
6
OK OR ERR
7
OK OR ERR
8
OK OR ERR
9
OK OR ERR
0
OK OR ERR
1
OK OR ERR
1
MODEL NAME
1
SERIAL NO.
*
OK OR ERR
*
OK OR ERR
*
OK OR ERR
1
PROJECTOR NAME
Note
If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under CONTROL CONTENTS.
*1
FINE SYNC can only be set in the displayed RGB mode.
•*2SERIAL NO. CHECK command is used to read out the 12 digits of serial No..
-91

Wired Remote Control Terminal Specifications

Specifications of wired remote control input
ø3.5 mm minijack
External: +5 V (1 A)
Internal: GND
Function and transmission codes
CONTROL
ITEM
ON
STANDBY
VOLUME +
VOLUME –
MUTE
MENU
KEYSTONE
BLACK SCREEN
ENTER
RESIZE
UNDO
FREEZE
ENLARGE (+)
ENLARGE (–)
SYSTEM CODE
C1
C2
C3
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
DATA CODE
C4
C5 C6
C7
C8
C9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
1
0
1
0
0
0
1
0
1
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
1
0
0
1
0
0
1
1
0
1
0
0
0
1
1
0
0
1
1
1
0
1
1
1
0
0
1
1
0
1
1
0
1
1
0
1
C10 C11
1
1
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
EXTERNAL
C12
C13
1
0
0
0
0
1
0
1
1
1
1
0
1
0
CODE
0
1
0
0
0
1
1
0
0
0
0
1
0
1
C14
CONTROL
C15
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
ITEM
AUTO SYNC
ƒ
ß
©
GAMMA
PinP
BACK
FORWARD
BREAK TIMER
INPUT 1
INPUT 2
INPUT 3
INPUT 4
SYSTEM CODE
C1
C2
C3
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
C4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C5 C6
0
0
0
0
0
0
0
0
0
0
0
0
0
0
C7
1
0
0
0
0
1
0
0
1
1
0
0
1
1
1
0
1
1
0
0
0
1
1
0
1
0
1
1
DATA CODE
C8
C9
0
1
1
1
1
1
0
0
1
1
0
0
1
1
1
1
1
1
1
0
1
0
1
0
0
0
0
0
C10 C11
1
1
1
0
1
0
1
0
0
0
0
0
1
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
EXTERNAL
CODE
C12
C13
1
1
0
1
0
1
1
0
1
0
1
0
1
1
0
1
0
1
0
1
0
0
0
0
0
0
0
0
C14
C15
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
Wired remote control function code
LSB MSB
C1 System Code C5 C6 Data Code C13 C14 C15
10110********10
System codes C1 to C5 are fixed at 10110”.
Codes C14 and C15 are reverse confirmation bits, with 10 indicating Front and 01 indicating Rear”.
Sharp remote control signal format
Transmission format: 15-bit format
DDDDDD
67.5 ms 67.5 ms
Wave form of output signal: Output using Pulse Position Modulation
t
T
0
T
1
0001
t = 264 µs Pulse carrier frequency = 455/12 kHz
T
0 = 1.05 ms • Duty ratio = 1:1 1 = 2.10 ms
T
Transmission control code
15 bit Example of Reverse D to D
C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14
System Address
DDDDDDD
D
Function Key Data Bit
Data
Expansion
Mask
C15
Data
Deter-
mination
010
26.4 µs
C11DC20C31C41C50C61C70C80C90C100C110C120C130C141C15
C11DC20C31C41C50C60C71C81C91C101C111C121C131C140C15
t
0
1
D to D Common Data Bit Reverse in D
-92

Computer Compatibility Chart

Computer
Multiple signal support
Horizontal Frequency: 15–126 kHz, Vertical Frequency: 43–200 Hz*, Pixel Clock: 12–230 MHz
Compatible with sync on green and composite sync signals
UXGA and SXGA compatible in advanced intelligent compression
AICS (Advanced Intelligent Compression and Expansion System) resizing technology
The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
PC/ MAC/ WS
PC
VGA
SVGA
XGA
Resolution
640 × 350
720 × 350
640 × 400
720 × 400
640 × 480
800 × 600
1,024 × 768
Horizontal
Frequency
(kHz)
27.0 60
31.5
37.9
27.0
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
47.9
53.0
61.8
78.5
80.9
100.4
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
77.2
98.3
102.1
125.6
35.5
40.3
48.4
56.5
58.1
60.0
68.7
73.5
77.2
80.6
98.8
113.2
Vertical
Frequency
(Hz)
70
85 60 70 60 70 85 60 70 85 50 60 70 72 75 85 90
100 120 150 160 200
50
56 60 70 72 75 85 90
100 120 150 160 200
43 50 60 70 72 75 85 90 96
100 120 140
VESA
Standard
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔
Display
Upscale
True
PC/ MAC/ WS
PC
PC/
MAC 13
PC/
MAC 19
PC/
MAC 21
MAC
16
HP (WS) PC (WS)
WS
SGI (WS)
SUN (WS)
Resolution
1,152 × 864
SXGA
1,152 × 882
+
SXGA
1,400 ×1,050
UXGA
640 × 480 34.9 67
VGA
XGA
1,024 × 768
1,280×1,024
SXGA
800 × 600
SVGA
832
1,152
SXGA
1,280×1,024
1,280
SXGA
1,280×1,024
1,152
* Temporary noise may be visible with vertical frequencies
above 100Hz if OSD functions are activated.
1,280
×
1,024
1,600
×
1,200
×
×
×
×
624
870
960
900
Horizontal Frequency
(kHz)
54.3
64.0
64.1
67.5
75.7 80
77.3
90.2
54.8
65.9
67.4
64.0
74.6
78.1 74
80.0 75
91.1 85
108.4 100
64.0 60
74.7 52
75.0 60
81.3 65
87.5 70
90.1 72
93.8 75
106.3 85
48.4 60
60.0 75
80.0 75
46.8 75
49.6 75
68.5 75
78.1 72
60.0 60
85.9 85
53.5 50
76.8 72
60.9 66
71.9 76
Vertical
Frequency
(Hz)
60 70 72 75
85
100
60 72 74 60 70
VESA
Standard
✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔
Display
Advanced Intelligent
Compression
Intelligent
Compression
Upscale
True
Advanced Intelligent
Compression
Upscale
Advanced Intelligent
Compression
Note
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in CRT only mode. Details on how to change display modes can be found in your notebook computers operation manual.
When this projector receives 640 × 350 VESA format VGA signals, 640 × 400 appears on the screen. When receiving 1,600 × 1,200 VESA format signals, sampling occurs and part of the image may be cut as the image is displayed in 1,024 lines.
DTV
Signal
480I 480P 540P
580I 580P 720P
1035I 1080I 1080I
Horizontal Frequency (kHz)
15.7
31.5
33.8
15.6
31.3
45.0
33.8
33.8
28.1
Vertical Frequency (Hz)
60 60 60 50 50 60 60 60 50
-93

Troubleshooting

Problem
No picture and no sound
or projector does not start.
Sound is heard but no
picture appears.
Color is faded or poor.
Picture is blurred;
noise appears.
Check
Projector power cord is not plugged into the wall outlet.
Power to the external connected devices is off.
The selected input mode is wrong.
Cables incorrectly connected to rear panel of the projector.
Remote control batteries have run out.
External output has not been set when connecting notebook computer.
The cover of the lamp unit is not installed correctly.
Cables incorrectly connected to the rear panel of the projector.
“Bright” is set to minimum position.
Picture adjustments are incorrectly set.
(Video Input only)
Video input system is incorrectly set. (INPUT 1 and 2 only)
Input signal type (RGB/Component) is incorrectly set.
Adjust the focus.
The projection distance exceeds the focus range.
(Computer Input only)
Perform “Fine Sync” Adjustments (“Clock” Adjustment)
Perform “Fine Sync” Adjustments (“Phase” Adjustment)
Noise will appear depending on the computer.
The “DNR” (Digital Noise Reduction) setting is not correct.
Cables incorrectly connected to rear panel of projector.
Volume is set to minimum.
The MUTE display appears.
Page
17
35 17 13 17 87 17 46
46
66
46
26 27
48 48
65 17 35
36
Picture appears but no
sound is heard.
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates.
Image cannot be
captured.
-94
If the picture is normal, the sound is due to cabinet shrinkage caused by a room temperature changes. This will not affect operation or performance.
See “Maintenance Indicators”.
The signal in INPUT 1 or 2 is not an RGB XGA (1024 × 768)
signal. Images cannot be captured if the signals are different from the above.
83
67
Pict in Pict does not
work.
The projector cannot be
turned on or put into the
standby mode using the ON or STANDBY button
on the projector.
Picture is green on
INPUT 1 or 2
COMPONENT.
Picture is pink (no green)
on INPUT 1 or 2 RGB.
Picture is dark.
Picture is too bright and
whitish.
The VOLUME buttons on the projector do not
work.
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.
CheckProblem Page
The signal in INPUT 1 or 2 is set to a resolution that exceeds SXGA.
The signal in INPUT 1 or 2 is sending Component signals 480I, 480P, 540P, 580I, 580P, 720P, 1035I or 1080I.
The signal in INPUT 1 or 2 is set to interlace mode using RGB signals.
The Keylock level is set. If the Keylock level is set to Level B, all the buttons are locked. If the Keylock level is set to Level A, only the INPUT and VOLUME buttons are functional.
Change the input signal type setting.
The lamp indicator is blinking in red. Replace the lamp.
Picture adjustments are incorrectly set.
The VOLUME buttons do not work when: (try the VOL+/– on the remote control)
when the menu is displayed
when the lens menu is displayed
when Pict in Pict is working
during Enlarge (More than double size)
a dot by dot screen resolution larger the panel resolution
In the case of transmitting RS-232C commands from a
computer during standby, it takes a maximum of 30 seconds for the computer to receive the response code. Set the response code waiting time of the computer to 30 seconds or more.
57
71
46
83 46
89
-95

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 94 and 95. If this operation manual does not answer your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharplcd.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140 http://www.sharp.ca
Mexico Sharp Electronics Corporation Mexico
Branch
(525) 716-9000 http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin American
Group
(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com
Germany Sharp Electronics (Europe) GMBH
01805-234675 http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
0161-205-2333 custinfo@sharp-uk.co.uk http://www.sharp.co.uk
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1 http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr
Benelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723) Nederland 9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu
Australia Sharp Corporation of Australia
Pty. Ltd.
1300-135-022 http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972 http://www.sharpnz.co.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk
Taiwan Sharp Corporation (Taiwan)
0800-025111 http://www.sharp-scot.com.tw
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311 helpdesk@smef.global.sharp.co.jp
Spain Sharp Electronica Espana, S.A.
93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
Austria Sharp Electronics Austria (Ges.m.b.H.)
-96
(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se
0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002 lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr
India Sharp Business Systems (India)
Limited
(91) 11- 6431313 service@sharp-oa.com
Loading...