Sharp EL-500W Owner Manual

INTRODUCTION

/

DEUTSCH

(Rückseite)

ENGLISH

EL-500W

FRACTION/SCIENTIFIC CALCULATOR

OPERATION MANUAL

MODEL

DEG (°)

GRAD (g) RAD

Thank you for purchasing the SHARP Fraction/Scientific
Calculator Model EL-500W. This calculator will help you
understand mathematical concepts behind fraction calcula­tion, such as simplification and reduction.
After reading this manual, store it in a convenient location
for future reference.

Operational Notes

• Do not carry the calculator around in your back pocket, as
it may break when you sit down. The display is made of
glass and is particularly fragile.

• Keep the calculator away from extreme heat such as on a
car dashboard or near a heater, and avoid exposing it to
excessively humid or dusty environments.

• Since this product is not waterproof, do not use it or store
it where fluids, for example water, can splash onto it.
Raindrops, water spray, juice, coffee, steam, perspiration,
etc. will also cause malfunction.

• Clean with a soft, dry cloth. Do not use solvents or wet
cloth.

• Do not drop it or apply excessive force.

• Never dispose of batteries in a fire.

• Keep batteries out of the reach of children.

• This product, including accessories, may change due to
upgrading without prior notice.

SHARP will not be liable nor responsible for any inciden­tal or consequential economic or property damage caused
by misuse and/or malfunctions of this product and its
peripherals, unless such liability is acknowledged by law.

♦ Press the RESET switch (on the back) only in the follow-

ing cases. Note that pressing the RESET switch erases
all data stored in memory.

• Before using for the first time

• After replacing the batteries

• To clear all memory contents

• If an abnormal condition occurs and all keys are inop-

erative.

If service should be required for the calculator, use only a
SHARP servicing dealer, SHARP approved service facility,
or SHARP repair service where available.

Hard Case

DISPLAY

Symbol

Mantissa

(All symbols will not be displayed simultaneously, as shown
above.)

: Appears when the entire equation cannot be

displayed. Press </> to see the remaining

2ndF : Appears when @ is pressed, indicating that the

SIMP : Indicates that a fraction can be simplified further, or

DEG/RAD/GRAD: Indicates angular units (Degrees, Radians

(hidden) section.

functions shown in orange are enabled.

expressed with a lower denominator.

and Grads) and changes each time G is pressed.

Exponent

’ : Appears when statistical mode is selected.
M:Indicates that a numerical value is stored in the

independent memory.

BEFORE USING THE CALCULATOR

Key Notation Used in this Manual

In this manual, key operations are described as follows:

To specify π : @V
To specify Exp: E

To access functions printed in orange above keys, press @
first.
In this manual, number entry examples are shown with ordinary
numbers (i.e., “100” will be indicated instead of “10
0”).

Power On and Off

Press N to turn the calculator on, and

@F

to turn it off.

Clearing Methods

There are three clearing methods as follows:
Clearing Entry M*

operation (Display)

N
@c

RESET

: Clear × : Retain

*1Independent memory M.

2

Statistical data and last answer memory.

*

• To clear the independent memory (M), press NO.

1

STAT, ANS*

××
×

Editing the Equation

• Press < or > to move the cursor.

To return to the equation after getting an answer, press
< (>).

• To delete a number, place the cursor on the number to be

deleted, then press d.

• To insert a number, move the cursor to the place immedi­ately after where the number is to be inserted, then enter
the number.

15 + 8 N 15 + 8

15 –↓ 3

13 × 24 = N 13 * 24 =

15 ×↓ 24 = >d 5 =

<<dd

- 3

<(>)

15+8_

15_

15–3_

312.

13×24

360.

Priority Levels in Calculation

This calculator performs operations according to the following
priority:
Q Functions expressed with numerical data placed before

(such as x-1, x2, n!)

x, x

W y

y

¿

E π
R Functions expressed with numerical data placed after (such

as sin, cos)

T Multiplications with the sign “×” omitted from the front of a

function (such as 3cos20)

Y nCr, nPr
U ×, ÷
I +, –
O Operations end commands (such as =, M+, %,

RAD, GRAD, DATA, CD)

•A parenthesized calculation section has precedence over
other sections of the calculation.

INITIAL SETUP

Mode Selection

Normal Mode:
Used to perform arithmetic operations and function calcula­tions.

Statistical Mode:
Used to perform statistical operations. To enter statistical
mode, press @”. ’ appears on the display to
indicate that the statistical mode is selected. To return to
normal mode, press @” with ’ on the display.
’ disappears as the calculator returns to normal mode.

• The mode will remain selected when the calculator is turned

off.

• When executing mode selection, last answer memory will

be cleared.

Scientific Notation

People who need to deal with very large and very small num­bers often use a special format called exponential or scientific
notation.
A number expressed in scientific notation has two parts. The

2

first part consists of a regular decimal number between 1 and

10. The second part represents how large or small the num-

ber is in powers of 10.
While a calculation result is displayed in the floating point
system, press @´ to display the result in the scientific
notation system. Pressing @´ once again will bring
back the floating point system.
To enter a number in scientific notation, press E.

(1.2 × 1020) × (1.5 × 105) 1.2 E 20 * 1.5 E 5

3 ÷ 7 =
[Floating point] N 3 / 7 =
→ [Scientific notation] @´
[TAB set to 2] @i 2
→ [Floating point] @´

• Use @´ to switch to the scientific notation, press

@i, then give a value between 0 and 9 to set the
decimal placement. To reset, press @i 9.

• The number will be displayed in scientific notation if the

floating point value does not fit in the following range:

0.000000001 ≤ | x | ≤ 9999999999

• The last decimal digit in scientific notation will be rounded

off.

4.285714286×10

=

1.8×10

0.428571428

4.29×10

0.428571428

DEG,

25

–01

–01

Determination of the Angular Unit

DEG (°)

GRAD (g) RAD

In this calculator, the following three angular units (degrees,
radians, and grads) can be specified.

Press G

(rad)

SCIENTIFIC CALCULATIONS

• Select the normal mode.

• In each example, press N to clear the display before

performing the calculation.

Arithmetic Operations

12+16×3= N 12 + 16 * 3 =

350–120÷4= 350 - 120 / 4 =

72×(-12)–150= 72 *– 12 - 150 =

(5+21)×(30–16)= ( 5 + 21 )*

(6×103)÷(2×10-4)=

( 30 - 16 )=

( 6 E 3 )/
( 2 E– 4 )=

–1014.

30000000.

Constant Calculations

In constant calculations, the addend becomes a constant.
Subtraction and division are performed in the same manner.
For multiplication, the multiplicand becomes a constant.

245+60= N 245 + 60 =
12+60= N 212 + 60 =

150–20= 150 - 20 =
250–20= 250 - 20 =

200÷4= 200 / 4 =
180÷4= 180 / 4 =

15×3= 15 * 3 =
15×10= 15- 10 =

Functions

• For each example, press N to clear the display.

• Before starting calculations, specify the angular unit.

• The results of inverse trigonometric functions are displayed
within the following range:

θ = sin–1 x, θ = tan–1 x θ = cos–1 x

DEG –90 ≤ θ ≤ 90 0 ≤ θ ≤ 180

RAD – — ≤ θ ≤

GRAD –100 ≤ θ ≤ 100 0 ≤ θ ≤ 200

sin60[°]= Ns 60 =

π

cos–[rad]=

4

tan–11=[g]

ln 20 = @I 20 =

log 50 = @l 50 =

e3 = @e 3 =

π

π

—

2

2

Gu(@V/ 4
)=

G@T 1 =
G

0 ≤ θ ≤ π

0.866025403

0.707106781

2.995732274

1.698970004

20.08553692

60.

320.

364.

305.

72.

130.

230.

50.

45.

45.

150.

50.

1.7

10

= @¡ 1.7 =

32 + 52 =3 @L + 5 @L=

√32 + 3√21 =

74 =7 @™ 4 =

4! = 4 @!=

= 10 @q 3 =

10P3

=5 @Q 2 =

5C2

π

– = @V/ 3 =
3

141
– + – = 4 @• + 5 @•=

5

200 × 32% = 200 * 32 @%

150 ÷ 300 = ?% 150 / 300 @%

200 + (200 × 32%) =

300 – (300 × 25%) =

@⁄ 32 + 3 @$
21 =

200 + 32 @%

300 - 25 @%

50.11872336

34.

8.415778426

2401.

24.

720.

10.

1.047197551

0.45

64.

50.

264.

225.

Random Numbers

A pseudo-random number with three significant digits can be
generated by pressing @`=. To generate the next
random number, press =.

Angular Unit Conversions

Each time @g are pressed, the angular unit changes
in sequence.

90°→ [rad] N 90 @g

→ [g] @g
→ [°] @g

sin–10.8 = [°] @S 0.8 =

→ [rad] @g
→ [g] @g
→ [°] @g

1.570796327

100.

90.

53.13010235

0.927295218

59.03344706

53.13010235

Memory Calculations

This calculator has two memory allocations: independent
memory (M), and last answer memory (ANS). You will find
them especially useful when combinations of calculations be­come complicated, or when using the answer of previous
calculation to another operations.

Press NO to clear the independent memory (“M” sym­bol will disappear).

Independent memory (M)

O : Stores the result in the memory.
R : Recalls the value stored in the memory.

@; : Adds the result to the value in the memory.

30 + (3 × 5) = 30 +R=

N 3 * 5 O

(3 × 5) × 4 = R* 4 =

20+10–5= N 20 + 10 - 5 O

121+13×2= 121 + 13 * 2 @;

+) 21×3–16= 21 * 3 - 16 @;

(Total) R

NO

15.

45.

60.

25.

147.

47.

219.

Last answer memory (ANS)
When = is pressed, the calculation result will automati­cally be stored in the last answer memory.

@? : Recalls the value stored in last answer

memory.

6+4 = ANS N 6 + 4 =
ANS + 5 + 5 =

8 × 2 = ANS 8 * 2 =

2

ANS

4 ÷ 5 = 0.8…(A) N 4 / 5 =
4 × (A) + 60 ÷ (A) =

@L=

4 *@?+ 60 /
@?=

Calculating the Greatest Common Factor (G.C.F.)
or Least Common Multiple (L.C.M.)

To calculate the G.C.F. or the L.C.M., the procedures are as
follows:

What is the G.C.F.
of 24 and 36?

What is the L.C.M.
of 15 and 9?

N 24
@œ 36
=

N 15
@ˆ 9
=

Calculating Quotient and Remainder

“: Calculates the quotient and remainder.

23 ÷ 5 N 23 @“ 5
(R: Remainder) =

9.5 ÷ 4 9.5 @“ 4

–32 ÷ (–5) – 32 @“– 5

=

=

• Pressing “ cannot be followed by pressing a key for
another operation such as (+, –, ×, ÷), otherwise an error
will result.

• The calculator can display a quotient or remainder up to 5
digits in length, including the “–” sign. If numbers longer
than 5 digits are entered, normal division is performed.

FRACTION CALCULATIONS

Entering Fractions

• To enter fractions, use the following keys:

Ø : Places the symbol “

and the denominator.

∞ : Separates the integer (whole number) part

from the fractional part of a mixed number.

2

M

4– = N 2 Ø 3 =

3

M

1

4– = 4 ∞ 1 Ø 2 =

M

2

• Up to 10 key strokes, including “¬” and “/”, can be used

M
M
M
M

to enter a fraction.

Calculating with Fractions

Fractions can be incorporated into an arithmetic calculation.
“SIMP” symbol will appear with a calculation result if the

answer can be further simplified. Refer to the following sec­tion of this manual for details.

/

” between the numerator

10.

15.

16.

256.

0.8

78.2

24_

24GCF36_

12.

15_

15LCM9_

45.

23‘5_

4.

R

9.5‘4_

2.R1.5

–32‘–5_

6.R–2.

2/3

¬¬

4

¬

1/2

¬¬

3.