Schneider Electric VP222A-200H-1188-U181 Catalog Page

Selection Guide

Table 9. Valve Assembly 8” and 10” With PT Ports

Flow Rate

(GPM)

880 (min. 352) 8 VP222A-200S-880-U181

1188 (min. 475) 8 VP222A-200H-1188-U181

1320 (min. 528) 10 VP222A-250S-1320-U181

1630 (min. 652) 10 VP222A-250H-1630-U181

* Factory set. Complete ﬂow ranges are shown in tables for 8" and 10" on page 12 and page 19.

* Valve Size

(inch)

24 Vac Proportional with Position Output Signal

(MP4000)

Table 10. Speciﬁcation 8” and 10” Valve Body Actuators

8" and 10" Valve Body Actuator Part Number (actuator code) MP4000 (U181)

Input Signal Proportional, 0…10 Vdc, 2…10 Vdc, 0…20 mA, 4…20 mA, with selectable input signal action and Floating, DIP swtich selectable

Electrical Connection Screw terminal with conduit connector

Position Feedback Output Signal 0…10 Vdc, 2…10 Vdc, 0…20 mA, 4…20 mA

Spring Return –

Auxilary Switch Yes

Other Features Auto calibration, LED indication, powered manual override, adjustable speed

Linear/Equal% Valve Flow Curve Selection Yes

Actuator Speed s/mm 60Hz (50 Hz) 3 or 6 (3 or 6)

Power Consumption 15 VA

Operating Temperature Limits °F (°C) 32…131 (0…55)

Actuator Weight (lb.) 16.53

Regulatory Compliance cULus according to UL 60730-1A/-2-14 and CAN/CSA E60730-1/-2-14 and CE according to EN 60730-1/-2-14 per EMC [2014/30/

Specification Data Sheet F-27971

Installation Data sheet F-27958

a. When used with a proportional input signal. All actuators are 24 Vac. 50/60 HZ with conduit connector holes and wiring terminal block, manual override.

EU] and LVD [2014/35/EU]

Table 11. Application: Operation of PIBCV Valve Body Without Actuator

Operation of the PIBCV valve body without an actuator for an automatic ﬂow limiting balancing application.

PIBCV Valve

Size

1/2”…1-1/4”

1-1/2”, 2” VP220E-xxxxx

2-1/2”…4” VP220A-xxxxx

5”…6” VP221A-xxxxxx 9114071000 (not included with valve body)

8”…10” VP222A-xxxxx 9114072000 (not included with valve body)

The 9114070000, 9114071000, and 9114072000 Valve Stem Locks are secured to the valve body with a 10 mm allen wrench. See Table 15. Assembly Valve Body Configurations on page 13 for a listing of all PIBCV valve body part numbers.

Valve Body Series Valve Stem Lock Part Number Recommended Installation and Valve Shut Off Capability

VP228E-xxxxxxx, VP229E-

xxxxxxx

Use black cap provided with VP228E-xxxxxxx or

VP229E-xxxxxxx valve body

9114070000 (not included with valve body)

Install valve in the supply water pipe for best shutoff valve performance. To shutoff

valve tighten black cap (max. close off pressure is 14.5 psi). To shut off against a

Install valve in either the supply or return water pipe. To shutoff valve tighten bottom

higher differential pressure set the valve flow to 0%.

knob (max. close off pressure is 232 psi)

insert with a 8 mm allen wrench (max. close off pressure is 232 psi)

No shut off knob, set the valve to a 0% flow setting to shutoff flow