Page 1
®
Erie
PopTop
Temperature Controllers
Valves & Actuators
Make the most of your energy
Page 2
2
PopTop™
Erie’s motorized hydronic valves, the
PopTop™, provide convenient, reliable and
easy installation for a variety of heating
and cooling applications. Installation is a
snap with easy, one-handed removal or
engagement of the actuator to the valve
body. Push the button and lift. It’s that simple.
Features
• One-handed engagement or removal of the
motorized actuator to the valve body.
• Valve actuator can be easily attached after the
valve body has been installed into the system.
• Mounts quickly and easily without the need of
linkages or calibration.
• Available in 2-way and 3-way port congurations,
1/2” (15mm) through 1-1/4” (32mm) sweat or
1/2” (15mm) to 1” (25mm) threaded connections,
1.0 to 8.0 Cv range.
• Available factory coupled, or as individual bodies
and actuators.
• Direct replacement for all existing PopTop™
applications.
• Rugged 300 PSIG rated brass forged body
design for long life.
• UL listed actuator.
Erie Family of Products
Poptop™ Zone Valves
• 1/2”, 3/4”, 1” and 1-1/4” Sweat, NPT and
Inverted Flare Union.
• Two-position (on/off), 2-way and 3-way.
• General close-off or High close-off.
• Low voltage or line voltage.
Poptop™ Modulating Valves
• 1/2”, 3/4”, and 1-1/4” Sweat, NPT.
• Three-wire (on/off), 2-way and 3-way.
• 0-10, 0-5, 5-10 Vdc or 4-20 mA proportional
inputs.
• Spring return or non-spring return.
• Time out feature available.
Damper Actuators
• Direct and linkage drive.
• Spring return or motor driven open and closed.
• 2-wire or 3-wire control with end switch.
• Clockwise or counter-clockwise rotation.
Thermostats and Controllers
• Heating and cooling, low and line voltage
outputs.
• Digital display or dial control.
• Three-wire oating, modulating output.
• 0-10 Vdc or 4-20 mA proportional outputs.
Quality HVAC Controls
Page 3
PopTop™ Two Position Valves & Actuators
3
General Close-Off
For your residential and commercial
applications, Erie’s General Close-Off
valves and actuators offer precision
control for 2-position (on/off) spring
return temperature control. The
General Close-Off may be used in a
wide range of applications such as
radiant baseboard and fan coil for
easy installation and maintenance.
Features
• Direct replacement for all existing two-position, motorized PopTop applications.
• Sized to t most baseboard applications.*
• Rugged Brass forged 300 psig rated valve body.
• Up to 60 PSI (75 PSI for HCO valves and actuators) pressure
differential close-off.
• Spring return operation, normally closed or normally open.
• Voltages 24 to 277 VAC.
• End switch option on general temperature models.
High Close-Off “HCO”
For high-rise and commercial
applications, where higher close-off
is required, our High Close-Off valves
and actuators offer precise temperature
control. Our two-position (on/off)
“HCO” actuator may be interchanged
with General Close-Off actuators. This
may be used in applications such as
fan coil and VAV reheat.
• Terminal block option on general temperature models (24V).
• Chilled, hot water, and low pressure/low temperature steam
applications.
• Cv 1.0 to 8.0.
• Hysteresis synchronous motor design for long life.*
• Meets or exceeds ANSI IV standard for close-off.
• UL Listed actuator.
* General Close-Off Valves & Actuators only.
PopTop™ Modulating Valves & Actuators
Spring Return Valves & Actuators
The most modern, cost-effective range of
electrically operated, modulating, temperature
control, Erie’s patented equal percentage flow
plug, standard in zone valves up to 4.0 Cv., is
designed for applications requiring a constant,
level temperature. These highly reliable valves
are designed specifically for use in fan coil,
VAV reheat, unit ventilators, air handling unit,
baseboard and radiant applications. The compact
design installs in small compartments and still
allows service access. Designed for use in closed
hydronic heating and cooling applications.
Features
• Rugged Brass forged 300 psig rated valve body.
• Patented equal percentage ow plug up to 4.0 Cv.
• Cv 1.0 to 8.0.
• Manual override.
• Position indicator.
• Thermoplastic enclosure.
• Non-spring return operation.*
• Jumper selectable operating ranges.
Non-Spring Return
All of our PopTop Modulating
valves and actuators feature
a position indicator, manual
override, thermoplastic enclosure,
and time-out option. Modulating
valves are designed for a fan
coil, VAV reheat, unit ventilator,
air handling unit, baseboard and
radiant applications.
• 24 VAC, 3-wire oating and 0-10 VDC, 0-5 VDC, 5-10 VDC, or
4-20 mA proportional controls.
• Compatible with most DDC control systems.*
• Chilled or hot water applications.
• Time-out feature for extended life.
• Meets or exceeds ANSI IV standard for close-off.
• UL Listed actuator.
* Non-Spring Valves & Actuators only.
Quality HVAC Controls
Page 4
F-27125-6
© 2012-2015 Schneider Electric. All rights reserved.
September 2015
Loading...