Please make sure the following items are included with your LCD Display.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
Lift up the package box by
both sides of the package
•After unpacking the package, make sure to check the contents of the package.
•Make sure to keep the package box for transporting the product in the future.
Unpacking
holding the grooves on
box.
Note
Check the contents of the
package.
Remove the Styrofoam
and vinyl cover.
LCD Display
Manuals
Introduction
Quick Setup GuideWarranty Card
(Not available in all loca-
tions)
MagicInfo Software CD,
MagicInfo Manual CD
(Applicable to the UXN-2
model only)
Cables
Power Cord
Others
User's Guide
Remote Control
(BP59-00138A)
Sold separately
D-Sub CableDVI CableLAN Cable
Batteries (AAA X 2)
(Not available in all loca-
tions)
BNC to RCA Adaptor Jack
(Applicable to the UX-2
(Used with UXN-2 model
model only)
only)
Sold separately
Wall Mount KITRGB to BNC CableBNC to BNC Cable
RGB to Component CableSemi Stand KIT
Your LCD Display
Introduction
(Applicable to the UX-2
model only)
Front
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu
values.
•The BNC mode will not be activated on the UXN-2 model.
•MagicInfo supports the UXN-2 model only.
PIP button
Push the PIP button to turn the PIP screen On / Off.
More than one PIP cannot overlap on screen as BNC and the component
use the same terminal.
•PC : DVI / AV / Component / HDMI
•BNC : DVI / AV / HDMI
•DVI / AV : PC / BNC
•Component : PC
•HDMI : PC / BNC
Power button []
Use this button for turning the LCD Display on and off.
Brightness Sensor (Optional)
Automatically detects the surrounding brightness it accordingly.
Note
This function is activated only on the models equipped with an auto brightness sensor.
Power indicator
Shows PowerSaver mode by blinking green
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Rear
Aim the remote control towards this spot on the LCD Display.
Note
For detailed information concerning cable connections, refer to Connecting Cables under
Setup. The LCD Display 's configuration at the back may vary slightly depending on the LCD
Display model.
Introduction
Note
Applicable to the UX-2 model only.
Applicable to the UXN-2 model only.
Switches the LCD Display On/Off.
The power cord plugs into the LCD Display
and the wall outlet.
MDC(Multiple Display Control) Program Port
NENT Connection Terminal (Input))
POWER S/W ON [ │ ] / OFF [O]
POWER
RS232C OUT/IN (RS232C Serial PORT)
RGB/COMPONENT IN (PC/COMPO-
•Use a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)
•Connect the RGB/COMPONENT IN port
on the monitor to the COMPONENT port
on the external device using the D-SUB
to COMPONENT cable.
•Connect the RGB/COMPONENT IN port
on the monitor to the BNC port on the PC
using the D-SUB to BNC cable.
Introduction
DVI IN (PC Video Connection Terminal)
Use a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
DVI/RGB/HDMI AUDIO IN (PC/DVI/
HDMI(PC) Audio Connection Terminal (Input))
AV/COMPONENT AUDIO IN [L- AUDIO-
R]
Connect the port of the DVD, VCR (DVD /
DTV Set-Top Box) to the [ L- AUDIO - R ] port
of the LCD Display.
DVI OUT
•Connect a monitor to another monitor
through a DVI cable.
•Connect the DVI OUT port on the monitor
to the HDMI IN port on the other monitor
using the DVI to HDMI cable.
•DVI, HDMI and network signals sent via
the DVI OUT port are displayed on the
second display which has the DVI IN port.
Note
Up to 6 Full HD or 10 HD monitors can be
connected (May differ depending on the
product).
AV IN [VIDEO]
Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
AUDIO OUT
Headphone/External speaker output terminal.
HDMI IN
Connect the HDMI terminal at the back of
your LCD Display to the HDMI terminal of
Introduction
your digital output device using a HDMI cable.
Up to HDMI cable 1.0 can be supported.
BNC OUT [R, G, B, H, V] (BNC Terminal
(Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports.
The number of LCD Displays that can be
connected to the loopout depends on the cables, signal source, etc. With cables or signal
source where there is no degradation, up to
10 LCD Displays can be connected (May not
be supported depending on the connected
cable).
Note
(Applicable to the UX-2 model only)
(BNC/Component Connection Terminal
(input))
During component input, please check specifications for the input ports below.
[R/Y, G/PB, B/PR, H, V]
•[R/Y] --> Red port input
•[G/PB] --> Green port input
•[B/PR] --> Blue port input
Note
Applicable to the UX-2 model only.
RGB OUT
Note
Applicable to the UXN-2 model only.
LAN (LAN Connection Terminal)
Note
Applicable to the UXN-2 model only.
USB1,USB2 (USB Connection Terminal)
Introduction
Keyboard / Mouse, Mass Storage Device
Compatible.
Note
Applicable to the UXN-2 model only.
Kensington Lock
The Kensington Lock is a device used to
physically fix the system when using it in a
public place. The locking device has to be
purchased separately. The appearance and
locking method may differ from the illustration depending on the manufacturer. Refer to
the manual provided with the Kensington
Lock for proper use. The locking device has
to be purchased separately.
Note
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The location of the Kensington Lock may be
different depending on the model.
Using the Anti-Theft Kensington
Lock
1.Insert the locking device into the Ken-
sington slot on the LCD Display and
turn it in the locking direction .
2.Connect the Kensington Lock cable.
3.Fix the Kensington Lock to a desk or a
heavy stationary object.
The performance of the remote control may be affected by a TV or other electronic device
operating near the LCD Display , causing a malfunction due to interference with the frequency.
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.