Samsung SNH-V6430BNH User Manual

0678

SAMSUNG SMARTCAM

User Manual

SNH-V6430BNH

Samsung SmartCam

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. contents of this document without prior notice.

Co., Ltd. All righ ts reserve d.

makes the best to verify the integrity and correctness of the contents in this

Hanwha Techwin

reserves the right to change the

SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION: Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC NOTE: The manufacturer is not responsible for any radio or tv interference caused by

unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Operational Description

The operational description shall fulfil the requirements of Rule Part 2.1033(b)(4). The rule part requires, "A brief description of the circuit functions of the device along with a statement describing how the device operates. This statement should contain a description of the ground system and antenna, if any, used with the device".

The above requirement has been further interpreted by the FCC to mean that the description shall:

a. be an operational or technical description of how the device operates, is modulated and meets requirements;

b. describe the EUT completely. What is it (in plain English as well as technical terms)? Give a clear, concise functional description of device operation.

c. always describe the signal, such as modulation type, pulse repetition rate, signal type and information being sent. Describe all modulation types and all data rates.

Instructions & Warranty

The manufacturer is not responsible for any loss or radio/TV interference caused by unauthorized modification of the product.

Such modification will void the warranty of the product as well as the user’s right of use.

WARNING

• The product must be assembled and installed by an adult.

• Before using, read all instructions on this manual thoroughly and follow operational

instructions, warnings on this manual and printed on the product.

• To avoid entangled power cord, do not place it around the baby bed or other infant furniture. Keep this product and its power cord out of children’s reach.

• Especially, the power cord should be installed carefully while keeping it out of children’s reach.

• Never use the product near bath tub, sink, washing machine and in wet basement to avoid moisture.

• The product is not designed for medical monitoring, and requires a grown-up’s protective supervision on its use.

• To avoid overheating of the product, do not expose the product to direct sunlight; do not install or use near a heat source such as heater, radiator, cooking devices (ex: electric stove or oven) and other warming devices (ex: audio amplifier, TV, etc.).

• Make sure to keep ventilated while using the product. Avoid pillar or furniture that may block ventilation, when installing the product.

• Make sure to use the power adaptor provided. If used with unidentified adaptor, it may damage the product. The power adaptor must be used with regular household electric supply.

• Avoid sharp, pointed objects around the adaptor’s cable, not to damage the cable.

• Be warned and never hold the cable’s stripped part when connecting / disconnecting

the adaptor to/from the wall outlet.

• To avoid entangled cable lines, avoid using cable extension for adaptor’s power cord.

• The product’s servicing is allowed only to authorized Hanwha Techwin service

personnel.

• When using the product for children’s care, be careful to keep the product out of children’s reach.

• The product partially contains component which might cause respiration difficulty. Accessories and small parts of the product should be stored keeping out of children’s reach.

• The product is not designed to replace responsibility of human supervision on children.

• The product is not equipped with device of immediate notification to adult with

accidental/sudden children‘s move; it requires periodic checks and human supervision.

• This appliance and its antenna must not be collocated or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements.

• Please note that the content of a micro SD card used for other purposes may be deleted when it is mounted in the camera.

Contents

GETTING STARTED

Features ……………………………………………………… 5

What’s Included ……………………………………………… 6

Part names and functions …………………………………… 7

INSTALLATION & NETWORK CONNECTION

Installation …………………………………………………… 9

Network Connection and Settings …………………………… 11

MONITORING

Registration …………………………………………………… 13

Live Video …………………………………………………… 18

Setup ………………………………………………………… 21

Event Alarm ………………………………………………… 28

Playback ……………………………………………………… 28

Information …………………………………………………… 30

APPENDIX

Specifications ………………………………………………… 31

Troubleshooting ……………………………………………… 34

GettinG Started

Features 5

What’s Included 6

Part names and functions 7

Power Supply 8

Features

• Easy to install

- The Wi-Fi Direct button allows easy connection to a wireless router.

- Simply visit the home page (www.samsungsmartcam.com) and download and install the program without a separate installer program.

• Remote monitoring

- Whenever and wherever if you are in the Internet enabled environment, remote monitoring is ready for you.

- PC, laptop or smart phone can be used for monitoring.

• Real-time alarm

- When a motion and sound are detected, your smartphone will generate real time alarms.

• Saving in SD card

- When an event occurs, the user can save the video in their SD card.

• Downloading a recorded video

- You can download motion detection/audio detection/manually recorded video to the user's PC or smartphone (Android).

• Dustproof/Waterproof (weather resistant)

- Made to be weather resistant, it can be installed outside.

- Use waterproof tape to cover the connector part of the PoE since this part is not waterproof.

• PoE connection

- You can easily connect the camera to the power supply and network using a PoE adapter, even in a demanding installation environment.

• Used for indoor purposes

- You can install an outdoor camera for indoor purposes by connecting it with an indoor bracket.

` Condensation may occur if you install the camera outdoors with the indoor bracket

connected.

Getting Started

What’s Included

Check for components when opening the product package.

Camera PoE adapter & power plug LAN cable (10M) Quick Start Guide

Warranty Card GPL Lisence Tapping screw Plastic anchor

` Keep the packing container. You will need the serial number later to register the camera.

· English

Part names and functions

The camera is connected with the PoE adapter to

connect with the power supply and the network.

Wi-Fi is used for wireless communication between

PoE connection port

Angle adjustment hinge

Wi-Fi Direct button

camera and smartphone.

RESET

Luminance Sensor

Detects light levels where the camera is placed. Night vision mode changes according to detection result.

Camera lens

Built-in IR LEDs for night vision

Built-in microphone

Power/Network status LED

Reset button

Resets the camera settings to the default. The system restarts if you press the button for 10 seconds using a pointed object such as a needle.

` If you press too strongly, the button can break.

Micro card insertion hole

Getting Started

Power Supply

Using the PoE adapter

1. Push to insert the included PoE adapter in the power

plug, as shown in the figure below.

2. To remove the power plug from the PoE adapter,

press the [PUSH] section as shown in the figure below, and push up the power plug.

3. Connect the LAN cable from the PoE adapter [DATA & POWER OUT]

socket to the PoE socket.

4. Connect the LAN cable from the PoE adapter [DATA IN] socket to the LAN

port of the router.

` When connecting the camera wirelessly via Wi-Fi Direct, remove the LAN cable

connecting the PoE adapter and the router.

5. Plug the PoE adapter into an electrical outlet.

` Use the PoE adapter and power plug that have been included with the camera. Using

an incompatible adapter may cause the camera to malfunction.

` It takes about 30 seconds to reboot the camera completely. ` When the camera is turned on, the LED blinks red.

❖LED status

LED indicator shows operational status with colors.

Refer to table below for detailed meaning of the LED indicator.

Color Status

Red Booting up

Red Blinking Booting completed / Establishing network connection

Blue Blinking Connecting to the network.

Blue Local connection established

Green Connection to server completed / Normal operation

Yellow/Orange Waiting to connect with a wireless router

Purple Updating firmware

· English

inStallation & network ConneCtion

Installation 9

Precautions 9 Installing on the wall and ceiling using screws 10 Adjusting the camera angle 11

Network Connection and Settings 11

Precautions 11 Connecting via network cable 12 Connection using the Wi-Fi Direct function 12

Installation

Precautions

1. To facilitate monitoring, connect between the PoE adapter [DATA IN] port

and the router.

2. In a location with a good Wi-Fi signal and no interference, use Wi-Fi

communication.

3. Install the camera under the eaves to avoid the front of the lens from being

exposed to rainwater. Avoid humid places as well.

4. Do not install the device under direct sunlight or other strong light sources.

Place it where there is good visibility.

5. Do not install it in a place where there are a lot of obstacles.

6. When wiping the surface of the product, a clean and soft dry cloth should be

used. Moist the dry cloth with water and wring it thoroughly to remove extra water. (Do not use cleaners containing alcohol or solvents, detergents containing surface active ingredients, and skin care products or oil, as they can cause damage or deformation of the product.)

7. Do not install the product in places where there are or may be chemicals or

traces of oil. Cooking oils like soybean oil can cause damage or deformation of the product, so please do not install the product near the kitchen or the kitchen counter. This may cause damage to the product.

8. Please be careful not to get chemical substances on the surface of the

product when installing the product. Some detergents or chemical solvents like adhesives can cause serious damage to the surface of the product.

9. The function and performance of the product may not be guaranteed if the

product is not installed/uninstalled by the recommended procedure.

Installation & Network Connection

Installing on the wall and ceiling using screws

1. Take out the screws (M3xL20) and anchors (Φ5x25mm).

When installing on a wooden wall

2. Fix the bracket to the wall using screws, as

shown in the next image. Using a Phillips screwdriver, fasten screws in 3 screw holes on the wall on which the camera is to be installed.

When installing on a concrete wall

2. Fix the bracket on the wall using screws and

anchors. First, mark the wall on which the camera is to be installed as shown in the figure.

On the mark, drill a hole to a depth of about

3cm in the wall using a drill bit and drill with a 5mm diameter for concrete. Remove any debris remaining in the hole after drilling.

` Use caution when drilling to avoid injury.

4. Insert an anchor in each of the 3 holes for the

screws, then hit the back of the anchor with a hammer or a rubber mallet until it is completely inserted.

5. Insert a screw in each of the 3 holes in the

wall, and tighten the screws using a Phillips screwdriver.

6. Connect the PoE adapter to the camera.

· English

` Insert the cable through the hole at

the bottom of the bracket to prevent the cable from being pressed when installing the camera.

Adjusting the camera angle

1. Turn the bracket knob counter-clockwise.

2. Adjust the angle adjustment hinge to set

the desired camera angle.

3. Turn the bracket knob clockwise to

fasten.

Angle adjustment hinge

Bracket knob

Network Connection and Settings

Precautions

• The cable connecting the router to the camera should have a length of 70m or

less (based on CAT5e LAN cable)

• The wireless network access may fail, depending on the communications

environment. In this case, a wired connection is recommended.

• For details about the network settings and password, contact your network

administrator or service provider.

• For a specific Internet service requiring user authentication, you may not access

the service. If this is the case, contact the service provider.

• Do not access the unauthorized network.

• The farther the distance from the Wireless Access Point, the longer time the

network connection may take.

• If you fail to access the selected wireless network, try a different Wireless

Access Point to make access.

• For more information about the router or the wireless connection, refer to the

documentation of the router or contact the router manufacturer.

• If the camera is connected to a multiple-Wireless Access Point network

environment, some video packets may be lost, depending on the network traffic load.

• According to the network policy (blocking UDP) of the service provider, the video

transmission can be limited to 7 minutes. For more details, refer to the descriptions on page 20, <Relay Mode>.

• In addition to the above two situations, you may encounter a network delay or

interruption due to the network conditions.

• Some hubs can have compatibility issues.

Installation & Network Connection

+ 25 hidden pages