Samsung SNH-V6414BN User Manual

SAMSUNG SMARTCAM

0678

User Manual

SNH-V6414BN

Samsung SmartCam

User Manual

SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

Operational Description

The operational description shall fulfil the requirements of Rule Part 2.1033(b)(4). The rule part requires, "A brief description of the circuit functions of the device along with a statement describing how the device operates. This statement should contain a description of the ground system and antenna, if any, used with the device".

The above requirement has been further interpreted by the FCC to mean that the description shall:

a. be an operational or technical description of how the device operates, is modulated and meets requirements;

b. describe the EUT completely. What is it (in plain English as well as technical terms)? Give a clear, concise functional description of device operation.

c. always describe the signal, such as modulation type, pulse repetition rate, signal type and information being sent. Describe all modulation types and all data rates.

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Samsung makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung reserves the right to change the contents of this document without prior notice.

Instructions & Warranty

The manufacturer is not responsible for any loss or radio/TV interference caused by unauthorized modification of the product.

Such modification will void the warranty of the product as well as the user’s right of use.

WARNING

• The product must be assembled and installed by an adult.

• Before using, read all instructions on this manual thoroughly and follow operational

instructions, warnings on this manual and printed on the product.

• To avoid entangled power cord, do not place it around the baby bed or other infant furniture. Keep this product and its power cord out of children’s reach.

• Especially, the power cord should be installed carefully while keeping it out of children’s reach.

• Never use the product near bath tub, sink, washing machine and in wet basement to avoid moisture.

• The product is designed for indoor use.

• The product is not designed for medical monitoring, and requires a grown-up’s

protective supervision on its use.

• To avoid overheating of the product, do not expose the product to direct sunlight; do not install or use near a heat source such as heater, radiator, cooking devices (ex: electric stove or oven) and other warming devices (ex: audio amplifier, TV, etc.).

• Make sure to keep ventilated while using the product. Avoid pillar or furniture that may block ventilation, when installing the product.

• Make sure to use the power adaptor provided. If used with unidentified adaptor, it may damage the product. The power adaptor must be used with regular household electric supply.

• Avoid sharp, pointed objects around the adaptor’s cable, not to damage the cable.

• Be warned and never hold the cable’s stripped part when connecting / disconnecting

the adaptor to/from the wall outlet.

• To avoid entangled cable lines, avoid using cable extension for adaptor’s power cord.

• The product’s servicing is allowed only to authorized Samsung service personnel.

• When using the product for children’s care, be careful to keep the product out of

children’s reach.

• The product partially contains component which might cause respiration difficulty. Accessories and small parts of the product should be stored keeping out of children’s reach.

• The product is not designed to replace responsibility of human supervision on children.

• The product is not equipped with device of immediate notification to adult with accidental/sudden children‘s move; it requires periodic checks and human supervision.

• This appliance and its antenna must not be collocated or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements.

• Please note that the content of a micro SD card used for other purposes may be deleted when it is mounted in the camera.

Contents

GETTING STARTED

Features ……………………………………………………… 4

What’s Included ……………………………………………… 5

Part names and functions …………………………………… 6

INSTALLATION & NETWORK CONNECTION

Installation …………………………………………………… 8

Network Connection and Settings …………………………… 10

MONITORING

Registration …………………………………………………… 11

Live Video …………………………………………………… 14

Setup ………………………………………………………… 17

Event Alarm ………………………………………………… 24

Playback ……………………………………………………… 24

Information …………………………………………………… 25

APPENDIX

Specifications ………………………………………………… 27

Troubleshooting ……………………………………………… 30

GettinG Started

Features 4

What’s Included 5

Part names and functions 6

Power Supply 7

Features

• Dedicated Wi-Fi Product

- The camera is registered through the Wi-Fi connection.

• Easy to install

- The Wi-Fi Direct button allows easy connection to a wireless router.

- Simply visit the home page (www.samsungsmartcam.com) and download and install the program without a separate installer program.

• Remote monitoring

- Whenever and wherever if you are in the Internet enabled environment, remote monitoring is ready for you.

- PC, laptop or smart phone can be used for monitoring.

• Real-time alarm

- When a motion and sound are detected, your smartphone will generate real time alarms.

• Saving in SD card

- When an event occurs, the user can save the video in their SD card.

• Two-way Audio

- With the built-in speakers and microphone, you can make Two-way communications. However, it is available only with the smart phone. (Not applicable to the PC or laptop computer.)

· English

What’s Included

Check for components when opening the product package.

Camera Power adapter and cable Quick Start Guide Warranty Card

GPL Lisence Tapping screw Plastic anchor

` Keep the packing container. You will need the serial number later to register the camera.

Getting Started

Part names and functions

Detects light levels where the camera is placed.

Night vision mode changes according to detection

Built-in IR LEDs for night vision

Power / Wi-Fi status LED, Built-in Mic

It connects with a power adapter.

· English

Luminance Sensor

result.

Camera lens

Power Connection Button

Speakers

Generate audio output from your smart phone.

Bracket knob

Connect the camera and bracket.

Wi-Fi Direct button

Wi-Fi is used for wireless communication between camera and smartphone.

Reset button

Resets the camera settings to the default. The system restarts if you press the button for 10 seconds using a pointed object such as a needle.

` If you press too strongly, the button can break.

Micro card insertion hole

Cable clip

Insert the power cable between the clips to connect it.

Power Supply

Plug-in the camera power adapter to the wall outlet and connect the camera as shown.

` Make sure to use the provided power adaptor. If you use an adaptor other than the

power supply adaptor provided in our package, the product may not operate properly.

` It will take about 1min for the camera to boot-up completely. ` When the camera is turned on, the LED blinks red.

❖LED status

LED indicator shows operational status with colors.

Refer to table below for detailed meaning of the LED indicator.

Color Status

Red Booting up

Red Blinking Booting completed / Establishing network connection

Blue Blinking Connecting to the network.

Blue Local connection established

Green Connection to server completed / Normal operation

Yellow/Light Green Waiting to connect with a wireless router

Purple Updating firmware

Getting Started

inStallation & network ConneCtion

Installation

Precautions

1. Install the camera in a place where the Wi-Fi signal can be reached and

without interference.

2. Keep it away from humidity such as around the humidifier.

3. Keep it away from direct sunlight, strong light or dust; install it in a place with

clear view.

4. Do not install it in a place where there are a lot of obstacles.

5. Keep the lens clean at all times.

Wipe off the dust with a soft cloth.

· English

Installation 8

Precautions 8 Installing on the wall with screws 8 Adjusting the camera angle 9

Network Connection and Settings 10

Precautions 10 Connection using the Wi-Fi Direct function 10

Installing on the wall with screws

Assembly

1. Remove the rubber packing attached to the

camera stand.

2. Take out the screws (M3xL20) and anchors

(Φ5x25mm).

3. If installing on a wooden wall, mount the bracket

wall using the screws as shown in the figure on the side. First, using a Phillips screwdriver, tighten the screws in the two holes on the wall to which you want to attach the bracket.

4. If installing on a concrete wall, mount the

bracket using screws and anchors. First, mark the wall to which you want to attach the bracket as shown in the figure.

9. If necessary, adjust the angle of the cable clip

and plug in the power cable.

5. On the mark, drill a hole to a depth of about

3cm in the wall using a drill bit and drill with a 5mm diameter for concrete. Remove any debris remaining in the hole after drilling.

` Use caution when drilling to avoid injury.

6. Insert an anchor in each of the 2 holes for the

screws, then hit the back of the anchor with a hammer or a rubber mallet until it is completely inserted.

7. Insert a screw in each of the 2 holes in the

wall, and tighten the screws using a Phillips screwdriver.

8. Connect the adapter plug to the power

terminal of the camera.

10. If the bracket hinge becomes loose, remove the

rubber cover and tighten the screw using a screwdriver.

Adjusting the camera angle

1. Place the camera stand on a flat

surface.

2. Adjust the camera’s shooting angle as

appropriate.

` If the bracket hinge becomes loose,

remove the rubber cover and tighten the screw using a screwdriver, then adjust the direction of the camera.

Installation & Network Connection

Network Connection and Settings

Connection using the Wi-Fi Direct function

Precautions

• The wireless network access may fail, depending on the communications environment.

• For details about the network settings and password, contact your network administrator or service provider.

• For a specific Internet service requiring user authentication, you may not access the service. If this is the case, contact the service provider.

• Do not access the unauthorized network.

• The farther the distance from the Wireless Access Point, the longer time the

network connection may take.

• If you fail to access the selected wireless network, try a different Wireless Access Point to make access.

• For more information about the router or the wireless connection, refer to the documentation of the router or contact the router manufacturer.

• If the camera is connected to a multiple-Wireless Access Point network environment, some video packets may be lost, depending on the network traffic load.

• According to the network policy (blocking UDP) of the service provider, the video transmission can be limited to 7 minutes. For more details, refer to the descriptions on page 16, <Relay Mode>.

• In addition to the above two situations, you may encounter a network delay or interruption due to the network conditions.

• Some hubs can have compatibility issues.

What is Wi-Fi Direct?

Using Wi-Fi Direct, you can easily connect your camera to a router without a cable.

1. When the power is connected, the power status LED lights up in red and

starts blinking when boot-up is complete.

2. When you press the Wi-Fi Direct button on the rear side of the camera, the

LED color changes to yellow/light green.

Wi-Fi Direct Button

Mobile

4. While the camera is connected to the server, status LED remains green.

5. Set up the wireless network environment in accordance with the <Network>

guidance on page. 19.

` The camera can only be registered via mobile.

` You can connect in relay mode if the router doesn't have UPnP.

Configuration may differ depending on the router model. Please refer to the router manual.

` Please contact the service provider if you have difficulty connecting to the Internet.

· English

+ 22 hidden pages