Samsung NX60T8311SG, NX60T8511SG, NX60T8111SG Installation Manual

Gas Slide-in Range
Installation manual
NX60*8*****
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 1 2020-03-26  6:41:17
WARNING: If the information in this manual is not followed exactly, a re or explosion may result causing property damage, personal injury or death.
ANTITIP DEVICE
WARNING
DO NOT store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch.
- DO NOT use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the re department.
Installation and service must be performed by a qualied installer, service agency, or the gas supplier.
ALL RANGES CAN TIP, RESULTING IN PERSONAL INJURY. TIPPING RANGES CAN CAUSE BURNS FROM SPILLS,
PERSONAL INJURY, AND/OR DEATH. INSTALL AND CHECK THE ANTI-TIP BRACKET FOLLOWING
THE INSTRUCTIONS AND TEMPLATE SUPPLIED WITH THE BRACKET.
To prevent accidental tipping of the range, attach an approved anti-tip device to the oor. (See Installing the Anti-Tip Device in the Installation Instructions.) Check for proper installation by carefully tipping the range forward. The anti-tip device should engage and prevent the range from tipping over.
If the range is pulled out away from the wall for any reason, make sure the anti-tip device is reengaged after the range has been pushed back into place.
Follow the installation instructions found in the Installation Manual. Failure to follow these instructions can result in death, serious personal injury, and / or property damage.
DO NOT step / sit / lean on the door or drawer to prevent accidental tipping of the range.
2 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 2 2020-03-26  6:41:17
Contents

Before you begin

Before you begin 3
Important safety information 4
Gas range components 11
What’s in the box 11
Installation requirements 13
Location requirements 13 To avoid breakage 15 Gas requirements 16 Special gas requirements (gas models sold in massachusetts) 17 Electrical requirements 17
Installation instructions 19
Installing your gas range 19 Step 1. Unpack the range 19 Step 2. Connect the range to gas supply 19 Step 3. Convert to lp gas (optional) 20 Step 4. Install the anti-tip device 21 Step 5. Plug in and place 21 Step 6. Level the range 22 Step 7. Assemble the surface burners 22 Step 8. Check the ignition of surface burners 23 Step 9. Final installation checklist 24 Adjusting the oven burner air adjustment shutters 24
About this manual
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.
Important note to the installer
Read all instructions contained in these installation instructions before installing the range.
Remove all packing materials from the oven compartments before connecting the electric and gas supply to the range.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the consumer.
Installation of this appliance requires basic mechanical skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the Warranty.
Important note to the consumer
Keep these instructions with your user manual for future reference.
As when using any appliance generating heat, there are certain safety precautions you should follow.
Be sure your range is installed and grounded properly by a qualied installer or service technician.
Make sure the wall coverings around the range can withstand the heat generated by the range.
Cabinet storage space above the surface burners should be a minimum of 30 in (76.2 cm).
Important note to the servicer
The electrical diagram is in an envelope attached to the back of the range.
Before you begin
English 3
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 3 2020-03-26  6:41:17

Important safety information

Important safety information
Important safety information
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
All electrical and gas equipment with moving parts can be dangerous. Please read the important safety instructions for this appliance in this manual. The instructions must be followed to minimize the risk of injury, death, or property damage.
Save this manual. Please Do Not Discard.
Symbols used in this manual
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in electric shock, personal injury, or property damage.
NOTE
Useful tips and instructions.
These warning icons and symbols are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference.
California Proposition 65 Warning
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Commonwealth of Massachusetts
This product must be installed by a licensed plumber or gas tter qualied or licensed by the State of Massachusetts. When using ball-type gas shut-off valves, you must use the T-handle type. Multiple exible gas lines must not be connected in series.
General safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
Do not touch any part of the range, including but not limited to, oven burners, surface burners, or interior surfaces during or immediately after cooking.
• Know the location of the gas shut-off valve and how to shut it off.
• Make sure the anti-tip device is properly installed on the range. See the installation instructions for more information.
• Do not let children near, in, or on the range. Do not let children play with the range or any part(s) of the range. Do not leave children unattended in an area where the range is in use. For children’s safety, we recommend utilizing the control/door lockout feature.
• Remove all packaging materials from the range before operating to prevent ignition of these materials. Keep all packaging materials out of children’s reach. Properly dispose the packaging materials after the range is unpacked.
• Do not store any object of interest to children on the cooktop or backguard of the range. Children climbing on the range to reach items could be killed or seriously injured.
4 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 4 2020-03-26  6:41:18
• Do not operate the range if the range or any part of the range is damaged, malfunctioning, or missing parts.
• Do not use the range as a space heater. This range is to be used for cooking purposes only.
• Do not use oven cleaners or oven liners in or around any part of the oven.
• Use only dry pot holders.
• Do not use the range to heat unopened food containers.
• Do not strike the oven glass.
When disposing of the range, cut off the power cord and remove the door.
• Unplug or disconnect power before servicing.
• Make sure all meat and poultry is cooked thoroughly. Meat should always be
cooked to an internal temperature of 160 °F (71 °C). Poultry should always be cooked to an internal temperature of 180 °F (82 °C).
Fire safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
• Do not store, place, or use ammable or combustible materials such as paper, plastic, pot holders, linens, curtains, gasoline or other ammable vapors or liquids near the range.
• Do not wear loose tting or hanging garments while using the range.
To avoid grease buildup, regularly clean the vents.
• Do not let pot holders or other ammable materials touch a heating element. Do
not use a towel or other bulky cloths in place of a pot holder.
• Do not use water on a grease re. To put out a grease re, turn off the heat source and smother the re with a tight-tting lid or use a multipurpose dry chemical or foam-type re extinguisher.
If a grease re should occur in the oven, turn off the oven by pressing the OFF/ CLEAR button. Keep the oven door closed until the re goes out. If necessary, use
a multipurpose dry chemical or foam-type re extinguisher.
• Do not heat unopened food containers - buildup of pressure may cause container
to burst and result in injury.
Important safety information
English 5
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 5 2020-03-26  6:41:18
Important safety information
Important safety information
Gas safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
If you smell gas:
• Close the valve and do not use the range.
• Do not light a match, candle, or cigarette.
• Do not turn on any gas or electric appliances.
• Do not touch any electrical switches or plug a
power cord into an outlet.
• Do not use any phone in your building.
• Evacuate the room, building, or area of all
occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the re department.
Checking for gas leaks
Leak testing of the appliance shall be conducted according to the manufacturer’s
instructions. Do not use a ame to check for gas leaks. Use a brush to spread a soapy water mixture around the area you are checking. If there is a gas leak, you will see small bubbles in the soapy water mixture at the leak point.
Electrical and grounding safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter or an extension cord.
• Do not use a damaged power plug, power cord,
or loose power outlet.
• Do not modify the power plug, power cord, or power outlet in any way.
• Do not put a fuse in a neutral or ground circuit.
Use a dedicated 120-volt, 60-Hz, 20-amp, AC, fused electrical circuit for this
range. A time-delay fuse or circuit breaker is recommended. Do not plug more than one appliance into this circuit.
• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.
This range must be Earth grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path for the electric current. This range is equipped with a cord having a grounding plug. The plug must be rmly plugged into an outlet that is properly installed and grounded in accordance with the local codes and ordinances. If you are unsure whether your electrical outlet is properly grounded, have it checked by a licensed electrician.
The range is supplied with a 3-pronged grounded plug. This cord must be plugged into a mating, grounded 3-prong outlet that meets all local codes and ordinances. If codes permit the use of a separate ground wire, we recommend that a qualied electrician determine the proper path for this ground wire.
Electrical service to the range must conform to local codes. Barring local codes, it should meet the latest ANSI/NFPA No. 70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions.
It is the personal responsibility of the range owner to provide the correct electrical service for this range.
6 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 6 2020-03-26  6:41:18
Installation safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
Have your range installed and properly grounded by a qualied installer, in accordance with the installation instructions. Any adjustment and service should be performed only by qualied gas range installers or service technicians.
• Do not attempt to service, modify, or replace your range or any part of your range unless it is specically recommended in this manual. All other service should be referred to a qualied technician.
Always use new exible connectors when installing a gas appliance. Do not use old exible connectors.
• Make sure the anti-tip device is properly installed on the range. See the installation instructions for more information.
Due to the size and weight of the range, have two or more people move the range.
• Remove all tape and packaging materials.
• Remove all accessories from the cooktop, oven, and/or lower drawer. Grates and
griddles are heavy. Use caution when handling them.
• Make sure no parts came loose during shipping.
• Make sure your range is correctly installed and adjusted by a qualied service
technician or installer for the type of gas (natural or LP) you will use. For your range to utilize LP gas, the installer must replace the 5 surface burner orices and 2 oven orices with the provided LP orice set, and reverse the GPR adapter. These adjustments must be made by a qualied service technician in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. The qualied agency performing this work assumes the gas conversion responsibility.
Installation of this range must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current Natural Gas Installation Code, CAN/CGA-B149.1, or the current Propane Installation Code, CAN/CGA-B149.2, and with local codes where applicable. This range has been design-certied by ETL according to ANSI Z21.1, latest edition, and Canadian Gas Association according to CAN/CGA-1.1, latest edition.
Important safety information
English 7
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 7 2020-03-26  6:41:18
Important safety information
Important safety information
Location safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
This range is for indoor, household use only. Do not install the range in areas exposed to the
weather and/or water.
• Do not install the range in a place which is exposed to a strong draft.
Select a level, well-constructed oor that can support the range’s weight. Synthetic ooring, such as linoleum, must withstand 180 °F (82 °C) temperatures without shrinking, warping, or discoloring. Do not install the range directly over interior kitchen carpeting unless a sheet of ¼ inch plywood or a similar insulator is placed between the range and carpeting.
Select a location where a grounded, 3- prong outlet is easily accessible.
If the range is located near a window, do not hang long curtains or paper blinds
on that window.
For the range to ventilate properly, make sure the range’s vents are not blocked or covered, and that there is enough clearance at the top, back, sides, and underneath the range. The vents allow the necessary exhaust for the range to operate properly with correct combustion and get the good cooking result.
• Make sure the wall coverings around the range can withstand heat up to 194 °F (90 °C) generated by the range.
Cabinet storage above the surface of the range should be avoided. If cabinet storage above the range is necessary: allow a minimum clearance of 30 inches (76.2 cm) between the cooking surface and the bottom of cabinets; or install a range hood that projects horizontally a minimum of 5 inches (12.7 cm) beyond the bottom of the cabinets.
Cooktop safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
• Make sure all burners are off when not in use.
• Do not use aluminium foil to line the grates or
any part of the cooktop.
• Do not leave burners unattended on medium or high heat settings.
Before igniting, make sure all burner caps are properly in place and all burners are level.
Always use the LITE position when igniting the burners and make sure the burners have ignited. If ignition fails, turn the knob to OFF and wait until the gas has dissipated.
When you set a burner to simmer, do not turn the knob quickly. Make sure the ame stays on.
• Do not place any objects other than cookware on the cooktop.
This cooktop is designed to cook with a wok or wok ring attachment. If foods are
amed, they should only be amed under a ventilation hood that is on.
Before removing or changing cookware, turn off the burners.
Remove food and cookware immediately after cooking.
Before removing any parts of the burner for cleaning, make sure the range is off
and completely cool.
After cleaning the burner spreader, make sure it is completely dry before re- assembling.
• Make sure the spark mark on the dual burner spreader is placed beside the electrode when it is assembled.
To avoid carbon monoxide poisoning, do not pour water into the cooktop well while cleaning.
Select cookware that is designed for top-range cooking. Use cookware that is large enough to cover the burner grates. Adjust the burner ames so that the ames do not extend beyond the bottom of the cookware.
To avoid cookware discoloration, deformity, and/or carbon monoxide poisoning, do not use cookware that is exceedingly larger than the grate.
8 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 8 2020-03-26  6:41:19
• Make sure cookware handles are turned to the side or rear of the cooktop, but not over other surface burners.
Stand away from the range while frying.
Always heat frying oils slowly, and watch as they heat. If you are frying foods at
high heat, carefully watch during the cooking process. If a combination of fats or oils is to be used during frying, mix them together before heating.
Use a deep-fryer thermometer whenever possible. This prevents overheating the fryer beyond the smoking point.
Use a minimum amount of oil when shallow pan-frying or deep-frying. Avoid cooking unthawed food or food with excessive amounts of ice.
Before moving cookware full of fats or oils, make sure it has completely cooled.
To prevent delayed eruptive boiling, always allow heated liquids to stand at least
20 seconds after you have turned off the burner so that the temperature in the liquid can stabilize. In the event of scalding, follow these rst aid instructions:
1. Immerse the scaled area in cool or lukewarm water for at least 10 minutes.
2. Do not apply any creams, oils, or lotions.
3. Cover with a clean, dry cloth.
Oven safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
Do not use the oven for non-cooking purposes such as drying clothes or storage. Use the oven for cooking purposes only.
Make sure the inner portion of the split oven-rack is in the proper position within the outer rack.
Make sure the oven racks are placed on the same level on each side.
• Do not damage, move, or clean the door gasket.
• Do not spray water on the oven glass while the oven is on or just after you have
turned it off.
• Do not use aluminium foil or foil liners anywhere in the oven. Do not use aluminium foil or like material to cover any holes or passages in the oven bottom or to cover an oven rack.
Stand away from the oven when opening the oven door.
Keep the oven free from grease buildup.
When repositioning the oven racks, make sure the oven is completely cool.
• Only use cookware that is recommended for use in gas ovens.
To avoid damaging the burner control knobs, always bake and/or broil with the
oven door closed.
• Do not broil meat too close to the burner ame. Trim excess fat from meat before cooking.
When using cooking or roasting bags in the oven, follow the manufacturer’s directions.
Important safety information
English 9
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 9 2020-03-26  6:41:19
Important safety information
Important safety information
Storage drawer safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
• Do not use the drawer for non-cooking purposes such as drying clothes or storage. Use the drawer for cooking purposes only.
• Do not touch the interior drawer surface or heating element.
To avoid steam burns, use caution when opening the drawer.
• Do not use aluminium foil to line the drawer.
• Do not use the drawer in the oven. Do not put the drawer in the oven during a
self-cleaning cycle.
• Do not leave containers of fat drippings in or near the drawer.
Self-cleaning oven safety
WARNING
To reduce the risk of re, electric shock, personal injuries, and/or death, obey the following precautions.
The self-cleaning feature operates the oven at temperatures high enough to burn away food soils in the oven. The range is extremely hot during a self-cleaning cycle. Do not touch any surfaces of the range during a self-cleaning cycle.
Keep children away from the oven during a self-cleaning cycle.
Before starting a self-cleaning cycle, remove all racks, cookware, and utensils
from the oven. Only porcelain-coated oven racks may be left in the oven.
Before starting a self-cleaning cycle, wipe grease and food soils from the oven.
• Do not put the lower drawer into the oven cavity when you run a self-cleaning
cycle.
When opening the door after a self-cleaning cycle, stand away from the oven.
If the self-cleaning cycle malfunctions, turn off the oven, disconnect the power
supply, and contact a qualied service technicia.
10 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 10 2020-03-26  6:41:19

Gas range components

What’s in the box

Parts supplied
Template Anti Tip Bracket (1) /
Screws (4)
Make sure you have received all of the supplied parts shown above.
If your range was damaged during shipping or you do not have all of the
supplied parts, contact your local retailer.
Filler Kit (1) & Screws (2)
Parts needed
Gas line shut-off
valve
135-degree elbow
(optional)
Flexible metal
appliance connector
½ in (ID) x 5 ft
Lag bolt or ½-in
(OD) sleeve anchor
Flare union adapter ¾ in or ½ in (NPT) x
½ in (ID)
Flare union adapter
½ in (NPT) x ½ in
(ID)
Gas range components
English 11
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 11 2020-03-26  6:41:20
Gas range components
Tools needed
Flat-blade
screwdriver
¼" Nut driver Pencil and ruler Level
Phillips screwdriver Open-end or
adjustable wrench
Pipe wrench (2)
Pipe joint compound
361/4 in
(921.2 mm) Min.
37 in
(939.8mm) Max.
Gas range components
in
16
7
Utility knife Soapy water
solution
Pliers
2915/16 in
(761.0 mm)
/
26
(671.7 mm)
in
16
/
11
28
(728.6 mm)
With handle
in (1250.3 mm)
4
1
/
49
Door fully open
12 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 12 2020-03-26  6:41:21

Installation requirements

Location requirements

Clearances and dimensions
BEFORE YOU BEGIN to install this appliance, refer to the following information, dimensions, and clearances. Do not locate the range where it may be subject to strong drafts. Provide adequate clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of the range. The location of the electrical outlet and gas piping may be adjusted to meet the following dimensions and clearances.
For installation in Canada, a free-standing range is not to be installed closer than
4.7 in (12 cm) from any adjacent surface.
CAUTION
This range has been designed to comply with the maximum allowable wood cabinet temperature of 194 °F (90 °C). Make sure the wall covering, countertops, and cabinets around the range can withstand the heat (up to 194 °F [90 °C]) generated by the range. If not, discoloration, delamination, or melting may occur.
Side Clearance Above Cooking Surface to Wall
4 in
(10.2 cm)
Minimum from
top of cooktop to
cabinets
30 in
(76.2 cm)
30 in
(76.2 cm)
6 in
(15.2 cm)
18 in
(45.7 cm)
13 in (33 cm)
Overhead
Cabinet Depth
CAUTION
Do not grasp the knob, handle and push when you install.
Installation requirements
CAUTION
DO NOT install the oven so that the door is ush with the cabinet. For OTR over Gas Stove, please follow local GAS CODE.
0 in (0 cm)
Clearance
Below
Cooking Top
and at Rear
and Sides of
Range
24.2 in
(61.5 cm)
0 in
(0 cm)
36 in
(91.4 cm)
24 in
(61 cm)
Lower
Cabinet
Depth
English 13
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 13 2020-03-26  6:41:22
Installation requirements
Minimum dimensions
Installation guide
WARNING
24"
3"
24"
3"
6"
B
If overhead cabinets are provided, a range hood should also be provided that projects horizontally a minimum of 5 in (12.7 cm) beyond the front of the cabinets. This will dissipate any heat buildup in the overhead cabinets to prevent death, personal injury, and/or re hazard. The ventilating hood must be constructed of sheet metal not less than 0.0122” thick. Install above the cooktop with a clearance of not less than 1/4” between the hood and the underside of the combustible
293⁄4"
25"
357⁄8"
material or metal cabinet. The hood must be at least as wide as the appliance and centered over the appliance. Clearance between the cooking surface and the ventilation hood surface must never be less than 24 inches.
Exception 1 : Installation of a listed microwave oven or cooking appliance over the cooktop shall conform to the installations packed with that appliance.
30-in (76.2-cm) minimum clearance between the top of the cooking surface and
361/4"-37"
2915⁄16"
2811⁄16"
267⁄16"
491⁄4"
A
the bottom of an unprotected wood or metal cabinet; or If no 30-in (76.2- cm) minimum clearance, 24-in (61-cm) minimum when the bottom of the wood or
Installation requirements
metal cabinet is protected by not less than 0.25-in (0.64-cm) ame-retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015-in (0.038-cm) stainless steel, 0.024-in (0.061-cm) aluminum, or 0.020-in (0.051-cm) copper.
18-in (45.7-cm) minimum between the countertop and the adjacent cabinet bottom.
A: Cabinet opening 30” (76.2)
IMPORTANT: If your cabinet have height over 37”, this range cannot be installed
without supporting unit like hard block.
Exception 2 : For island installation, maintain 2-1/2” minimum from cutout to back edge of countertop and 4” minimum from cutout to side edges of countertop.
IMPORTANT:
To eliminate the risk of burns or re caused by reaching over heated surface units, avoid having cabinet storage space located above the surface units. If you have cabinet storage space over the heating elements, you can reduce the risk by installing a range hood that projects horizontally a minimum of 5 inches beyond the bottom of the cabinets.
14 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 14 2020-03-26  6:41:22
Recommended locations for gas piping and electrical outlets
(For model NX60*8*****)
Recommended
17 in
(43.2 cm)
position
Optional rear ller kit
WARNING
Used to ll gap between the range back and wall. Adds a ller strip to the rear of the range. This kit can only be used when the opening in the countertop is 25” deep.
NOTE
If the countertop depth is greater than 25”, there will be a gap between the ller kit and the back wall.
Gas Wall Area
Recommended area for
through-the-wall and through-
the-oor connection of gas
pipe stub and shut-off valve.
9 in
(22.9 cm)
2 in
(5.1 cm)
Gas Floor Area
12 in
(30.5 cm)
30 in (76.2 cm)
Cabinet Opening
17 in (43.2 cm)
Recommended area for 120V electrical outlet on rear wall
CAUTION
You must use the rear ller kit to install the range in a freestanding cutout cabinet. For more information, see “Optional rear ller kit” as shown below.

To avoid breakage

Installation requirements
CAUTION
Please DO NOT push the unit strongly when you install. These actions can cause the damage to the unit.
Please DO NOT push the burner knobs when installing the range. (Grasp the L/R door area to push the unit.)
English 15
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 15 2020-03-26  6:41:23
Installation requirements
CAUTION

Gas requirements

Do NOT lift or handle the unit by the cooktop frame.
1. The counter top around the cut-out should be at and leveled (See hatched area on Fig. 1).
2. Before installing the unit, measure the heights of the two cabinet sides (C1~C4), front and back (See Fig. 1) from the oor to the top of the counter.
3. Level the range using the four leveling
C2
C1
C4
C3
legs so that the height from the oor to the underside of the cooktop frame is greater than the tallest cabinet measurement by at least
1
/16”.
4. Slide the unit into the cabinet (DO NOT
Fig. 1
Installation requirements
PUSH THE UNIT HARD). Make sure the center of the unit aligns with the center of the cabinet cut-out.
5. The metal ange under each side of the cooktop MUST be placed over the cabinet countertop for proper unit support. The cooktop should NOT rest directly on the countertop or else it could cause damage to the cooktop voiding the warranty. Level the unit if needed.
Provide adequate gas supply
This range is designed to operate at a pressure of 5 in (13 cm) of water column on natural gas or 10 in (25 cm) of water column on LP gas (propane or butane).
Make sure you are supplying your range with the type of gas for which it is designed. Do not attempt to convert the appliance from the gas specied in this
manual to a different gas without consulting the gas supplier.
This range is convertible for use on natural or propane gas. If you decide to use this range on LP gas, conversion must be made by a qualied LP installer before attempting to operate the range.
For proper operation, the pressure of natural gas supplied to the regulator must be between 5 in and 13 in (13 cm and 33 cm) of water column.
For LP gas, the pressure supplied must be between 10 in and 13 in (25 cm and 33 cm) of water column.
When checking for proper operation of the regulator, the inlet pressure must be at least 1 in (2.5 cm) greater than the operating (manifold) pressure as given.
The pressure regulator located at the inlet of the range manifold must remain in the supply line regardless of whether natural or LP gas is being used.
A exible-metal appliance connector used to connect the range to the gas supply line should have an I.D. of 0.5 in (1.3 cm) and be 5 ft (152 cm) in length for ease of installation. In Canada, exible connectors must be single-wall metal connectors no longer than 6 ft (183 cm) in length.
Do not kink or damage the exible metal tubing when moving the range.
16 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 16 2020-03-26  6:41:23

Special gas requirements (gas models sold in massachusetts)

Electrical requirements

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS:
WARNING
Gas leaks may occur in your system, creating a dangerous situation. – Gas leaks may not be detected by smell alone. – Gas suppliers recommend you purchase and install a UL-approved gas detector.
Gas detector should be installed in accordance with the manufacturers instructions.
Range must be installed by a qualied plumber or gas tter by the State of Massachusetts.
A T-handle manual gas valve MUST be installed in the gas supply line to your range.
If a exible gas connector is used to install your range, multiple exible gas lines must not be connected in series.
WARNING
To reduce the risk of re, electric shock, or personal injury:
All ranges
Do not use an extension cord or adapter plug with this range.
This range must be properly grounded.
Check with a qualied electrician if you are in doubt as to whether your range is
properly grounded.
Do not modify the plug provided with your range—if it doesn’t t the outlet, have a proper outlet installed by a qualied electrician.
All wiring and grounding must be done in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70 – Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions and local codes and ordinances.
Wiring diagram is located on the back of the range. (Inside of the cover back wire)
This range is equipped with an electronic ignition system that will not operate if
plugged into an outlet that is not properly polarized.
Gas models
All gas models are equipped with a power cord with an equipment-grounding conductor and a grounding plug.
A 120-Volt, 60-Hz, AC, approved electrical service with 20-amp circuit breaker or time-delay fuse is required for all U.S. and Canadian models.
Check for ¾-in (1.9-cm) UL-listed strain relief where the power cord comes out of the range cabinet.
Do not reuse a power supply cord from an old range or other appliance.
The power cord electric supply wiring must be retained at the range cabinet with
a suitable UL-listed strain relief.
A time-delay fuse or circuit breaker is also recommended.
Installation requirements
English 17
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 17 2020-03-26  6:41:23
Installation requirements
Grounding
All ranges must be grounded for personal safety.
All gas models have a power cord with an equipment-grounding conductor and a
grounding plug.
The plug must be rmly plugged into a three-prong outlet that is properly installed and grounded in accordance with all local codes and ordinances. In the event of a malfunction or breakdown, grounding will decrease the risk of electrical shock by providing a path for the electric current.
Do not use a damaged power plug or loose wall outlet.
Do not use an extension cord or adapter with this appliance.
Do not, under any circumstances, cut, modify, remove, or otherwise defeat the
grounding (third) prong from the power cord. If the plug and the outlet do not match or you have any doubt, have a qualied electrician install the proper outlet. The customer should have the wall receptacle and circuit checked by a qualied electrician to make sure the receptacle is properly grounded. Ground Fault Circuit Interrupters (GFCIs) are not required or recommended for gas range receptacles.
Installation requirements
• NEVER connect ground wire to plastic plumbing lines, gas lines, or water pipes.
CAUTION
Failure to follow these instructions can result in death, re, or electrical shock.
Usage situations where appliance power cord will be disconnected frequently
Do not use an adapter plug in these situations because disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the adapter ground terminal. Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a three-prong (grounding) receptacle by a qualied electrician before using the appliance.
Additional installation requirements for mobile homes
The installation of appliances designed for mobile home installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard for Manufactured Home Installations, latest edition (Manufactured Home Sites, Communities and Set-Ups), ANSI A225.1, latest edition, or with local codes. In Canada, mobile home installation must be in accordance with the current CAN/CSA Z240/MH Mobile Home Installation Code.
Power cord location
The power cord for this appliance is located on the back of the range, near the bottom right hand corner. The 53-in (135-cm)
2”
71/8
Power cord location
power cord will come installed on the range and taped to the back for shipping.
18 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 18 2020-03-26  6:41:24

Installation instructions

Installing your gas range

IMPORTANT:
Please read the following instructions, as well as the Important Safety Instructions section at the front of this manual, completely and carefully BEFORE installing and/or operating the gas range. Improper installation, adjustment, service, or maintenance can cause personal injury or property damage.
NOTE
To order parts or accessories, contact your local retailer or refer to the last page.
NOTE
To ensure proper installation, we strongly recommend that you hire a professional installer.

Step 1. Unpack the range

Remove all packaging materials. Failure to remove packaging materials could result in damage to the appliance.
Inventory all loose parts against the Parts supplied components listed on page 11. Check for shipping damage and/or missing parts. Any damage and/or missing
parts should be reported to your local retailer.

Step 2. Connect the range to gas supply

Shut off the main gas supply valve before disconnecting the old range and leave it off until the new hookup has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on.
Because hard piping restricts movement of the range, the use of a CSA International-certied exible metal appliance connector is recommended unless local codes require a hard-piped connection.
WARNING
If the information in this manual is not followed exactly, a re or explosion may result, causing death, personal injury, or property damage.
– Do not store or use gasoline or other ammable vapors and liquids in the
vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
DO NOT light a match, candle, or cigarette.
DO NOT try to light any appliance.
DO NOT touch any electrical switch.
DO NOT use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call the re department.
– Installation and service must be performed by a qualied installer, service
agency, or gas supplier.
Never use an old connector when installing a new range. If the hard-piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.
To prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with Teon on all male (external) pipe threads.
1. Install a manual gas line shut-off valve in the gas line in an easily accessed location outside of the range. Make sure everyone operating the range knows where and how to shut off the gas supply to the range.
2. Install male 0.5-in (1.3-mm) are union adapter to the 0.5-in (1.3-mm) NPT internal thread at the regulator inlet. Use a backup wrench on the regulator tting to avoid damage. When installing the range from the front, remove the 90° elbow for easier installation.
3. Install male 0.5-in (1.3-mm) or 0.75-in (1.9-mm) are union adapter to the NPT internal thread of the manual shut-off valve, taking care to back up the shut-off valve to keep it from turning.
Installation instructions
English 19
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 19 2020-03-26  6:41:24
Installation instructions
Installation instructions
4. Connect exible metal appliance connector to the adapter on the range. Position range to permit connection at the shut-off valve.
5. When all connections have been made, make sure all range controls are in the off position and turn on the main gas supply valve. Use a liquid leak detector at all joints and connections to check for leaks in the system.
WARNING
To prevent death, personal injury, explosion, and/or re hazard, DO NOT use a ame to check for gas leaks.
When using test pressures greater than ½ psig to pressure-test the gas supply system of the residence, disconnect the range and individual shut-off valve from the gas supply piping. When using test pressures of ½ psig or less to test the gas supply system, simply isolate the range from the gas supply system by closing the individual shut-off valve.
WARNING
Do not exceed 25 ft-lbs of torque when making gas line connections. Overtightening may crack the pressure regulator resulting in a gas leak.
Flexible connector hookup
Installer: Inform the consumer of the location of the gas shut-off valve.
Gas Shut-Off Valve
Adapter
Flex Connector (6-ft max.)
Gas Flow into Range
Adapter
0.5-in or 0.75-in Gas Pipe
Tubing Line to Oven Burner Control Valve
Tubing Line
to Cooktop
Control
Manifold
Pressure
Regulator
NOTE
If your area requires a rigid pipe hookup, contact a qualied installer, service agency, or gas supplier.
NOTE
The gas shut-off valve should be installed in an accessible location in the gas piping, external to the appliance, for the purpose of turning on or shutting off the gas to the appliance.

Step 3. Convert to lp gas (optional)

All new gas ranges are shipped from the factory set up to use natural gas. Any Samsung gas range can be converted to use LP gas. Refer to page 55 in the User Manual to contact a qualied service technician.
The conversion process should only be performed by a qualied LP gas installer. Conversion instructions and LP orices will be supplied with the LP conversion kit. The conversion to LP requires all burner orices to be changed (5 surface burners and 2 oven burners).
In addition, the nozzle on the gas pressure regulator needs to be reversed. All replaced orices must be left with the consumer, including the instructions and retrot sizes and orice indication. Checking the ame quality all burner after converting to lp gas.
20 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 20 2020-03-26  6:41:24

Step 4. Install the anti-tip device

WARNING
To reduce the risk of tipping, the appliance must be secured by properly installing the anti-tip device packed with the appliance.
All ranges can tip, resulting in personal injury.
Tipping ranges can cause burns from spills, personal injury, and/or death.
To prevent accidental tipping, install and check the anti-tip bracket following the
instructions and template supplied with the bracket.
An anti-tip bracket and screws, installation instructions, and template are shipped with every range (PN DG94-00870B). The instructions include information necessary to complete the installation of the anti-tip bracket. Read and follow the instructions on the sheet and use the template for anti-tip bracket installation. If not properly installed, the range could be tipped by you or a child standing, sitting, or leaning on an open oven door.
*approximately
21
/32” (16.5 mm)
Anti-Tip bracket
Screw must enter wood or concrete
*NOTE: To install the Anti-Tip bracket, release the leveling leg. A minimum clearance of
21
/32” (16.5 mm) is required between the range bottom and the kitchen oor.
To check if the bracket is installed and engaged properly, remove storage drawer and look underneath the range to see that the leveling leg is engaged in the bracket. Carefully tip the range forward. The bracket should stop the range within 4 inches (10.2 cm) of tipping. If it does not, the bracket must be reinstalled.
If the range is pulled from the wall for any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket. Never completely remove the leveling legs or the range will not be secured to the anti-tip device properly.

Step 5. Plug in and place

WARNING
BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 17
18 in this manual. Improper connection of the grounding plug can result in a risk
~ of electric shock.
• All gas ranges come with a power cord. The power cord is connected to the rear
of the range. Please review “Electrical requirements” on pages 17 ~ 18.
The electrical system, including the power cord, is preinstalled and prewired at the factory. Altering any part of this system may result in a short or overload.
1. Plug in the power cord. Make sure the outlet meets local or national electrical
codes as referenced on pages 17 ~ 18.
2. Slide the range into place.
3. Check the gas supply line to make sure it did not get damaged and it stayed
connected during positioning.
4. Check to make sure the back leg of the range has slid into the anti-tip bracket.
Carefully tip the range forward to ensure that the anti-tip bracket engages the back brace and prevents tip-over.
Installation instructions
English 21
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 21 2020-03-26  6:41:24
Installation instructions
Installation instructions

Step 6. Level the range

Leveling leg
1. Make sure the range is positioned where you want it.
2. Using a wrench, level the range by turning the front leveling legs in or out as necessary. Counterclockwise shortens the leg and lowers the range. Clockwise lengthens the leg and raises the range.
NOTES
Adjusting the two front legs is usually
sufcient, but adjust all four legs if necessary.
Adjust the leveling legs only as far as
necessary to level the range. Extending the leveling legs more than necessary or removing legs can cause the range to be unstable.
3. If range is next to or between cabinets, make sure the cooktop (without the surface burner grates) is level with the countertops.
4. Position an oven rack in the center rack position.
5. Check the level of the range with a carpenter level using the two positions shown at right.
6. After the range becomes level, slide the range away from the wall so that the anti-tip bracket can be installed.

Step 7. Assemble the surface burners

Precise Simmer Burner (RR)
Flat surface Concave line
CAUTION
Do not operate the surface burners without all burner parts in place.
1. Position surface burner heads on top of the surface burner manifolds as shown at right. The electrodes will t into the slot in the bottom of the heads. Make sure the surface burner heads are at and parallel with the cooktop.
2. Place the matching size caps on top of each surface burner head.
NOTE
The caps on Precise simmer burner (RR) and inside Dual Burner (RF) can be interchangeably used.
3. Place the left, center, and right surface burner grates on the cooktop. The edges of the grates should match up with the edges of the cooktop.
22 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 22 2020-03-26  6:41:25

Step 8. Check the ignition of surface burners

2
1
2
3
1
Check the operation of all cooktop and oven burners after the range has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in.
All surface and oven burners have electronic ignition.
To turn on a surface burner:
1. Push in and turn the control knob for that surface burner to the Lite position. The “clicking” sound indicates the electronic ignition system is operating properly. The burner will light in about 4 seconds, after the air has been purged from the supply line.
2. After the burner lights, turn the control knob to the desired setting. The “clicking” sound will stop and the ame height will change from Max. to Min. during turning the control knob.
3. Repeat steps 1 and 2 to check the operation of each surface burner in succession.
NOTE
Place food in the oven after preheating if the recipe calls for it. Preheating is important for good baking results. After the oven has reached the desired cooking temperature, it will beep 6 times.
Checking the ame quality:
All combustion ames need to be visually checked to determine their ame quality.
1. Soft blue ames—Normal for natural gas operation.
2. Yellow tips on outer cones—Normal for LP gas operation.
3. Yellow ames—Abnormal for any gas operation; call for service.
NOTE
If burner ame looks like 3, the range should not be used until it is serviced. Call for service. Normal burner ames shall look like 1 or 2, depending on the gas type you use.
Installation instructions
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 23 2020-03-26  6:41:26
English 23
Installation instructions
Installation instructions

Step 9. Final installation checklist

You have just completed installing your range. Make sure all controls are in the off position and the ow of ventilation air to the range is unobstructed. The following is a checklist to conrm your range is safely installed and ready for operation.
– Gas line has been properly connected to
the range. The gas has been turned on. All connections have been checked for leaks.
– Range is plugged into the properly
grounded electrical receptacle.
Gas Range Plug
Locking screw
– Approved anti-tip bracket is properly
installed and engaged with the range.
– Range is leveled and is rmly sitting on a
solid, level oor.
– Gas surface burners have been properly
assembled.
– All burners have been tested for proper
operation.
– FOR INSTALLER ONLY—Check and/or
adjust the broil and oven burner ames as described on pages 22-23 in this manual.

Adjusting the oven burner air adjustment shutters

All oven burners have an air adjustment
Air
adjustment
shutter
shutter. The purpose of the shutter is to regulate the ow of air to the ames. Properly adjusted ames should burn steadily with approximately 1-in of blue cone. The ames should never extend past the edge of the burner bafes. Even though these are preset at the factory, they should be checked and, if needed, adjusted periodically to ensure efcient operation.
To check and adjust the oven burner air adjustment shutters:
1. Open the oven door.
2. Remove the oven racks.
3. Remove the oven oor.
4. Press the Bake pad, then the START/SET pad.
5. After the oven has lit, visually check the ames coming out of the upper and
lower burners. If adjustment is needed, carefully adjust the air adjustment shutters.
The shutters are located at the base of the burner manifolds near the back oven wall.
To adjust the shutter, loosen the locking screw and rotate the shutter towards the open or closed position as needed. If ames
Locking screw
NOTE
If the range is set up for natural gas, the ames should burn with no yellow tipping. If the range is set up for LP gas, small yellow tips at the end of the cones are normal.
Locking screw
are lifting off the burner ports, gradually reduce the air shutter opening until the ames are stabilized.
If ames are too yellow and/or too large, gradually increase the air shutter opening until the ames have approximately a 1-in blue cone.
After the ames are adjusted properly, shut off the oven, retighten the locking screws, replace the oven bottom and racks, and close the oven door.
24 English
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 24 2020-03-26  6:41:26
To adjust ame low setting
Identify which burner is exhibiting too high or too low of simmer rate via manifold panel graphics.
1. Rotate a knob to LO position and remove the knob from the valve stem while the ame is lit.
Simmer Set
Screw
Memo
Small Screwdriver
Valve Stem
WARNING
1. Do not completely remove the valve set screw from the valve stem. The valve set screw is an integral part of the gas valve assembly. Removing the valve set screw will cause gas to leak.
2. After adjusting the valve set screw, inspect the assembly for gas leaks.
2. Carefully push the screw driver into the
stem of the valve, until it hits the simmer set screw. Make sure the screwdriver athead is seated into the set screw groove.
3. Rotate valve set screw clockwise to decrease LO setting ame output, or rotate set screw counter clockwise to increase LO setting ame output.
Installation instructions
English 25
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 25 2020-03-26  6:41:26
Memo
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 26 2020-03-26  6:41:26
Loading...
+ 58 hidden pages