Roland VR-700 User Manual
VR-700 Function Mode Quick Reference
This publication shows you how to make changes in the parameters related to organ and ensemble sounds. These parameters make up only a portion
of all the parameters that can be set in the Function mode. For detailed explanations concerning these parameters, and for information on all the other
parameters, which are not covered in this publication, refer to the VR-700 Owner’s Manual.
Operations in Function Mode
Press the [FUNCTION/ENTER] button to enter Function
1.
mode.
Use the [+] button or [–] button to select the Group.
2.
Refer to the relevant pages in this document to learn about the
correspondence between Groups and what is indicated in this unit’s
display.
Press the sound button that corresponds to the
3.
parameter for which you want to change the settings.
Refer to the relevant pages in this document to learn about the
correspondence between the buttons and the parameters.
4.
Use the [+] button or [–] button to change the value of
the setting.
5.
To exit Function mode, press the [DISPLAY/EXIT] button
twice.
Organ Sound Parameters
Saving Your Settings As a Favorite
Press the [DISPLAY/EXIT] button twice to exit Function
1.
mode.
While together holding down both the [WRITE] and
2.
[BANK] buttons, press one of the FAVORITE [1]–[8]
buttons to specify the save-destination bank.
While holding down the [WRITE] button, press one of the
3.
FAVORITE [1]–[8] buttons to specify the save-destination
favorite number.
With the Group already selected, press the [+] button or [–] button until
Parameter
Value
Remarks
Tone button
(blink red)
Parameter
Value
Remarks
Wheel Type
1: VINTAGE 1
2: VINTAGE 2
3: SOLID
4: CLEAN
VINTAGE 1/2 are tonewheels
representative of the 70s/60s.
SOLID emphasizes the lowerrange harmonics of VINTAGE 1.
CLEAN is free of leakage noise.
Key Off Click Level
0–31
–
Amp Type Organ Fine Tune Leakage Level Key On Click Level
1: Jazz oriented
2: Vacuum tube amp for guitar
3: Rock oriented
4: Readily distorts
5: Level easily set
1, 3, 4, and 5 are amps with
rotating speakers. 2 is a guitar
amp.
Reverb Send Level Active Amp Enhancer – –
0–127 OFF, ON – –
–
is shown in the display.
-50– +50 (cent) 0–127 0–31
– – –
Enhances the distortion
characteristics according to
the Amp Type
– –
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
* 5 1 0 0 0 1 2 3 1 4 - 0 2 *
Percussion Parameters
With the Group already selected, press the [+] button or [–] button until
Button
[PIANO]
[E. PIANO] Percussion Normal Level 0–15
[STRINGS] Percussion Slow Time 0–127
[CHOIR/SCAT] Percussion Fast Time 0–127
[BRASS] Percussion Recharge Time 0–10
[SYNTH LEAD] Percussion H-Bar Level 0–127
Parameter Value
Percussion Soft Level 0–15
is shown in the display.
Rotary Parameters
With the Group already selected, press the [+] button or [–] button until is shown in the display.
You can make settings for the following parameters when the sound button is blinking in red.
Button
[PIANO]
[E. PIANO] Rotary Tweeter Level 0–127
[STRINGS] Rotary Woofer Rise Time 0–127
[CHOIR/SCAT] Rotary Tweeter Rise Time 0–127
[BRASS] Rotary Woofer Fall Time 0–127
[SYNTH LEAD] Rotary Tweeter Fall Time 0–127
[SYNTH PAD] Rotary Woofer Spread 0–10
[GUITAR] Rotary Tweeter Spread 0–10
[BASS] Rotary Woofer Slow Speed 0–127
[OTHERS] Rotary Tweeter Slow Speed 0–127
Parameter Value
Rotary Woofer Level 0–127
To make settings for the parameters below, start with already appearing in the display. Then press the [TO LOWER/PEDAL] button, so the
sound button is blinking in green.
Button
[TO LOWER/PEDAL] ➝ [PIANO]
[TO LOWER/PEDAL] ➝ [E. PIANO] Rotary Tweeter Fast Speed 0–127
[TO LOWER/PEDAL] ➝ [STRINGS] Rotary Mic Distance 0–10
[TO LOWER/PEDAL] ➝ [CHOIR/SCAT] Rotary Speed Randomize 0–10
[TO LOWER/PEDAL] ➝ [BRASS]
Parameter Value
Rotary Woofer Fast Speed 0–127
Rotary Brake Position
(Position at which the speaker will be
stopped by the ROTARY [BRAKE] button)
FrE: Stop at a random position (Free)
FIX: Always stop at the same position (Fix)
Ensemble Sound Parameters
With the Group already selected, press the [+] button or [–] button until is shown in the display.
Button
[PIANO]
[E. PIANO] Ensemble 2 Expression Switch OFF, ON
[STRINGS] Ensemble Fine Tune -50–+50 (cents)
[CHOIR/SCAT] Reverb Send Level 0–127
Parameter Value
Ensemble 1 Expression Switch OFF, ON
Loading...