Please read before setting up your system.
Every Rocketboost network must contain at least one hub device, which directs network data tra c and helps devices join the network. The network can have only one hub, which can be enabled by using the hub switch on the back of all
Rocketboost transmitters. See your User Guide for instructions on joining devices to the network.
Package contents:
TM
AC cable
|
GUIDE |
|
|
|
SETUP |
|
|
Wireless receiver |
QUICK |
|
|
Quick Setup |
User Guide Cable spool |
||
IR remote |
|||
|
3 ft. speaker cable (2) |
|
Receiver |
9 |
|
|
|
|
10 |
|
|
|
SPEAKER-OUT (4-8 Ohm) |
||
|
|
|
|
|
|
|
|
|
|
AC IN |
|
|
|
|
|
|
|
|
|
|
|
|
120V~,60Hz |
|
|
|
|
|
|
|
|
|
|
|
11 |
12 |
13 |
14 |
|
|
|
|
|
|
|
|
1 |
Standby LED |
|
11 Removable cable spool slot |
|
|
|
|
|
|
|
|
|
2 |
Power/Join button |
12 AC IN connector |
||
|
|
|
|
|
|
|
|
3 |
Power/Join indicator |
13 Removable cable spool slot |
||
|
|
|
|
|
|
|
|
4 |
Bass button |
|
14 SPEAKER OUT jacks |
|
|
|
|
|
|
|
|
|
5 |
BASS indicator |
|
|
|
|
|
|
|
|
|
|
|
6 |
SOURCE indicator |
|
|
|
|
|
|
|
|
|
|
|
7 |
SOURCE button |
|
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
8 |
HD indicator |
|
|
|
9 |
IR sensor |
|
|
|
||||||||
|
|
|
|
|
|
|
|
10 VOLUME knob |
|
|
|
Step 1 Preparing the remote control
Toactivatethebattery:
Removethetabfromthebottomoftheremotecontroltoenablethebattery.
Step 2 Connecting the receiver |
Connect the right surround |
|
|
|
speaker to the right speaker |
|
|
terminal of the receiver, using |
|
|
the supplied three-foot speaker |
|
SPEAKER-OUT (4-8 Ohm) |
cable. Connect the red |
|
S |
speaker cord to the red (+) |
AC IN |
|
terminals, and the black speaker |
120V~,60Hz |
|
|
|
R L |
cord to the black (-) terminals. |
|
|
Repeat to connect the left |
|
|
speaker. |
Step 3 Establishing communication |
|
|
Topoweronandswitchtojoiningmode: |
|
|
1 Press and hold the |
button on the hub unit (the hub will be identi ed by a solid green power LED or ashing green if there |
|
are no other devices connected to the network) for more than three seconds to put the unit into joining mode. |
||
The unit will stay in joining mode for about 30 seconds. |
|
|
•The Power/Join indicator starts blinking fast. |
|
|
2 Press and hold the |
button on the Rocket sh receiver for more than 3 seconds to put the unit into joining mode. |
The unit will stay in joining mode for 30 seconds.
The Power/Join indicator starts blinking quickly. When connected, both units will show a solid LED for successful connection.
• If the Power/Join indicator blinks at a slower rate, the link is not successful. Retry the joining operation.
See your User Guide for additional information.
09-0476
QUICK SETUP GUIDE