RISCO Group iWISE User Manual

iWISE QUADSEQ Grade 3

Installation Instructions

iWISE QUADSEQ Grade 3

The iWISE QUADSEQ Grade 3 is designed to meet DD243 requirements for sequential
confirmation and also meet PD6662, EN 50131-1 and EN50131-2-2

The iWISE QUADSEQ Grade 3 includes built - in Triple EOL resistors for installation
simplicity, and active IR anti-masking for reliable detection of masking attempts.

iWISE QUADSEQ Grade 3 Main Features

x PD6662, EN50131-1, EN50131-2-2 Grade 3
x Two PIR Detectors in a single housing with separate alarm outputs
x Two non-overlapping coverage patterns
x Coverage 12m
x Active IR Anti-Mask (up to 15cm)
x Built-in Triple EOL resistors, jumper selectable
x Wall and Cover tampers
x Opto - relays for low current consumption and long life time
x Remote and Local Self Test
x LED control input
x LED control polarity Jumpers
x 3 LEDs for easy walk test
x True Temperature Compensation
x Wall tamper proof swivel (optional)

Principle of Operation 3D Image of the Application

The unit contains two independent detectors in a single housing. When
mounted in the corner of a room, one detector covers the two walls
(side area), while the second detector covers the center of the room.
When an intruder enters the room via a door or window, the side area
triggers. When the intruder then moves to the center of the room, the
second detector triggers, providing a sequentially confirmed alarm.

Installation Considerations

x Before installing, study the space to be protected carefully in order to

choose the exact location of the unit for the best possible coverage.

x Corner installation is recommended. The detection side areas

(which are two curtain zones at 80° to each other), should cover the
room walls, and therefore any vulnerable doors and windows.

x The additional internal PIR detector covers the center area of the

room. Recommended mounting height is 2.4m.

x Avoid installations where rotating machines (e.g. fans) are normally

in operation within the coverage pattern. Do not mount the detector
in direct sunlight or near any heat sources. Point the unit away from
glass exposed to the outdoors and objects that may change
temperature rapidly.

x The installation surface should be solid, smooth and vibration free.

Coverage

Top View

8

6

4

2

0m

2

4

6

8

0m 2 4 6 8 10 12m

Side Area

0

90

Side Area

Center Area

Grade 3 requirements.

2.4m
2

0m

2.4m
2

0m

Side View - Center Area

0m 2 4 6 8 10 12m

Side View - Side Area

0m 2 4 6 8 10 12m

Installation

1. To open the front cover:
x Turn the front cover locking screw counter-

clockwise.

x Insert a screwdriver through the dedicated slot/s to

open the detector's front cover.

2. Loosen the PCB holding screw, located on the right

hand side of the PCB and slide the PCB down until the
screw reaches the widened opening. Lift the PCB up to
remove.

3. Mounting - iWISE QUADSEQ Grade 3

either on a flat surface or on a wall corner (corner
mounting).

x Using a suitable tool, open the following

knockouts on the detector’s base.

x A1, A2 and A3: External cables knockouts (open

out at least one wiring knockout)

x A4, A6, A9, A12, and A15: Wall mounting

knockouts

x When using a swivel adapter use the A4, A6, and

A15 openings to connect the detector to the
swivel adapter.

x A5 and A10: Right corner mounting knockouts
x A11 and, A14: Left corner mounting knockouts

Note:

The A7, A8 AND A13 knockouts are not to be used in this
configuration.

4. Use the base as a template for marking the installation

holes (mark through the mounting holes).

5. Put the base in a safe place, drill the required holes in

the surface or in the corner, and insert anchors (if
necessary).

6. Insert external cables through the cable hole/holes.

7. Mount the rear cover in its final location.

PCB View Terminal Wiring/Outputs Activation

TAMPER
(upper) EOL

TAMPER EOL

LONG

Range Scale

Mark

LED State Description
Yellow On Center Area PIR detection
Green On Side Area PIR detection
Red Flashing Fault / Anti Masking detection ***

All LEDs

Notes:

* To enable LED indications, the LED jumper has to be in ON position and no signal is attached to the LED terminal.
** When an activation signal (see LED Activation jumper for settings) is applied to the LED input of the terminal block, LEDs will be disabled.
*** AM indication continues until masking is removed, and during power up AM calibration.

Terminal

Block

ALARM

ALARM

-12 +

CENTER

SIDE

LEDS

SIDE

LEDS

OFF

ON

ALARM

NONE

SIDE

SENSITIVITY

1K

2.2K

4.7K
SELF TEST

5.6K

6.8K

1K

2.2K

4.7K

5.6K

6.8K

Tamper

Switch

Active IR

Anti-Mask Transmitter

Anti-Mask Receiver

Flashing
(One after another)

FAULT/AM

can be mounted



TAMPER

LED

FAULT/AM

CONF

INT EXT

CENTER

LED
INPUT

12V

0V

HIGH LOW

AM E.O.L

SHORT

12K

LOC REM

ALARM CENTER

1K

2.2K

4.7K

5.6K

6.8K

Range
Adjustment
Screw

Active IR



At Power - up, the LEDs will blink continuously, one after the other, until the end of the warm-up period (2-3 minutes).
At the end of power-up period the RED LED will continue to flash until the end of AM calibration.

Important: Always close the front cover prior to applying power, for correct AM calibration.

8. Seal the remaining holes with a sealant compound.

9. Reinstall the PCB into its desired position.

10. Wire terminal (see Terminal Wiring section)

11. Set jumpers (see Jumper Settings section).

12. Install the front cover back to its place (in a reverse sequence of the
removal).

13. Reapply electrical power to the detector for correct AM calibration.
Recalibrate after every successive removal of cover.

14. Perform a Walk test (see Walk Test section).

Back Plate Knockouts

A15

A14

Back tamper
“Breakable” plate

A13

A12

A11

A1 A2 A3

A4

A5

A6

Range
Adjustment
Bolt Thread

A7

A8

A9

A10



12VDC

ALARM

+ -

Terminal Description

- 12 +
ALARM
SIDE
ALARM
CENTER
TAMPER
FAULT/AM

LED

12VDC Input
Normally closed output

Normally closed output
Normally closed output

Normally closed output
The FAULT/AM output opens in the following events:

x Detector is masked (Alarm Side and Alarm Center

also open in this case)

x Self test failed
x Input voltage is low (6VDC - 8VDC)

See LED INPUT jumper for settings
When an activation signal is applied to the LED input of the
terminal block, LEDs will be disabled (see also Self Test in
Jumper Settings table).
LEDs are enabled if nothing is connected (unless LED jumper
is OFF).

ALARM

SIDE

CENTER

FAULT/AMTAMPER

LED

Page 1

Page 2

Jumper Position Function
SENSITIVITY

LED INPUT

Used to determine the sensitivity of the center PIR area.

(Default)

Used to determine the polarity of the external input.

(Default)

HighHigh Sensitivity selection



Low: Low Sensitivity selection

12V: 12v has to be connected in order to disable the LED’s.

GND or N.C. has no influence on the LED’s status. (see self test jumper configuration)

0V: The GND has to be connected in order to disable the LED’s.
12v or N.C. has no influence on the LED’s status. (see self test jumper configuration)

INT: The detector’s alarm activation is determined by the detector’s internal logic. Intruder detection on
one of the PIR’S detection areas (side or center) activates the appropriate LED only.
If both PIR’S (side and center) are triggered within a time window of 2 minutes, then both side and
center relays are activated
EXT: The security panel determines the detector’s alarm activation. Intruder detection on one of the
detection zones (side or center) activates the appropriate LED and Relay only.



CONF

LED

V

0

Used to determine the relay’s activation logic.



(Default)
Used to determine the operation of the detector’s LEDs

ON: LEDs are enabled

Note:



(Default)

SELF TEST

Used to test the PIR channels functionality

(Default)

EOL
RESISTORS
JUMPERS

TAMPER EOL JUMPERS

No
Resistor
(Default)

EOL Resistors Scheme

Note:

Side & Center area can be connected to DEOL or

The jumpers are used when connecting the detector to a DEOL or TEOL Zone. The jumpers allow the selection of
TAMPER, TAMPER (upper), ALARM CENTER and ALARM SIDE E.O.L resistors (1K, 2.2K, 4.7K, 5.6K or 6.8K),
according to the control panel. An additional double jumper allows the connection of 12K FAULT/AM E.O.L resistor (see
EOL Resistors Scheme).

1K

2.2K 4.7K 5.6K 6. 8K

TEOL areas on the panel as illustrated below.

ALARM

SIDE

CENTER

ZONE

ALARM
CENTER

TAMPER

ALARM

TAMPER FAULT AM

ALARM SIDE

DEOL/TEOL

ALARM SIDE

+12- LED

When an activation signal (see LED Activation jumper for settings) is applied to the LED input of the
terminal block, LEDs will be disabled.

OFF: LEDs are disabled

LOC (Local Self Test): If there is no alarm detection within 1 hour from previous detection, the detector

will self test both PIR channels.
In case the local self test fails, the FAULT/AM Relay is activated for a period of 2.5 seconds.
REM (Remote Self Test): Remote Self Test is activated when the LED terminal input is switched from
DISABLE to ENABLE mode (see LED Activation jumper for settings).
In case the remote self test passes, the Alarm Relays are activated for a period of 5 seconds.
In case the test fails, FAULT/AM Relay is activated for a period of 2.5 seconds.

TAMPER (upper) EOL JUMPERS

1K

2.2K 4.7K 5.6K 6.8KNONE

Short
(Default)

ALARM
CENTER

TEOL ZONE

TAMPER+12- LED

FAULT AM

TAMPER

ALARM

+12-

ALARM

SIDE

DEOL ZONE

ALARM

CENTER

CENTER

FAULT/AM

TAMPER

FAULT AM

TAMPER

LED

ALARM CENTER JUMPERS

1K

2.2K 4.7K 5.6K 6.8K

No
Resistor
(Default)

 

ALARM SIDE EOL JUMPERS

1K

2.2K 4.7K 5.6K 6.8K

No
Resistor
(Default)



FAULT/AM EOL

JUMPERS

12K

No
Resistor
(Default)

Walk Test

Two minutes after applying power (warm-up period), walk test the Detector over the entire protected area to verify proper operation of the
unit.

Important: Always close the front cover prior to applying power to the detector.]

7HFKQLFDO6SHFLILFDWLRQ

Electrical
Current consumption 12mA at 12VDC, 39mA at

Voltage requirements 9 -16VDC
Alarm contacts 24VDC, 0.1A
Tamper contacts 24VDC, 0.1A
FAULT/AM contacts 24VDC, 0.1A
Environmental
RF immunity According to EN50130-4
Operating temperature -20°C to 55°C (-4°F to 130°F)
Storage temperature -20°C to 60°C (-4°F to 140°F)

Physical

Size 127.6 x 64.2 x 46.6 mm
Weight 115 gr. (4 oz)

RISCO Group Warranty

RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24
months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products
not manufactured by the Seller, Seller cannot guarantee the performance of the security system which uses this product. Seller's obligation and liability under
this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, any product not meeting the
specifications. Seller makes no other warranty, expressed or implied, and makes no warranty of merchantability or of fitness for any particular purpose.
In no case shall seller be liable for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other
basis of liability whatsoever.
Seller's obligation under this warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or consequential
damages or delay.
Seller does not represent that its product may not be compromised or circumvented; that the product will prevent any persona; injury or property loss by
burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and
maintained alarm may only reduce the risk of burglary, robbery or fire without warning, but is not assurance or a guarantee that such will not occur or that there
will be no personal injury or property loss as a result.
Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that the product fails to give warning. However, if
seller is held liable, whether directly or indirectly, for any loss or damage arising from under this limited warranty or otherwise, regardless of cause or origin,
sellers maximum liability shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against seller. No employee or
representative of Seller is authorized to change this warranty in any way or grant any other warranty.

United Kingdom

Tel: [phone]
[e-mail]

USA

Tel: [phone]
[e-mail]

12VDC (max. with all LEDs ON)

(5 x 2.5 x 1.84 in.)

Italy

Tel: [phone]
[e-mail]

Brazil

Tel: [phone]
[e-mail]

Spain

Tel: [phone]
[e-mail]

China

Tel: [phone]
[e-mail]

2UGHULQJ,QIRUPDWLRQ

Part Number Description

RK800QS0000A iWISE QUADSEQ Grade 3

France

Tel: [phone]
[e-mail]

Poland

Tel: [phone]
[e-mail]

Belgium

Tel: [phone]
[e-mail]

Israel

Tel: [phone]
[e-mail]

PD6662, EN50131-1, EN50131-2-2 Grade 3 Class II

© RISCO Group 12/08 5IN800QS B

Page 3



Page 4