canno t be overch arged. H owever, if the pr oduct is n ot going to b e used for a n
extended period time ( 2-3 mont hs), unplug it from the mai ns and sto re.
Fully re charge your
when you would like t o use it aga in.
Thank you for choosing Remington®. Our products are designed to meet the
highest standard of quality, functionality and design. We hope you enjoy using
your new Remington® appliance. Please read the instructions for use carefully and
keep in a safe place for future reference.
CAUTION
Use this appliance only for its intended use as described in this manual. Do not
use attachments not recommended by Remington
Do not use this product if it is not working correctly, if it has been dropped or
damaged, or dropped into water.
DESCRIPTION
On/Off Switch
1.
3 mm
trimmer
8
2.
Shaver attachment
3.
Adjustable guide comb
4.
Charging indicator light
5.
Charging adaptor
6.
Storage pouch
7.
Head guard
8.
9.
USB Cable
®
.
Before using your for the first time, charge for 14-16 hours.
Ensure the product is switched off.
Connect the charging adaptor to the product and then to the mains. The charging indicator
To preserve the life of your batteries , let them run out every six months the n rechar ge for
14-16 hours .
CHARGING VIA STANDARD ELECTRICAL SOCKET
Ensur e the product is swi tched of f.
Conne ct the ch arging ad aptor to the produ ct and then to the ma ins.
When charging the LED indicator will illuminate.
Allow 14-16 hours for a complete charge.
USB CHARGING VIA PC
Ensure the product is switched of f.
Connect your USB cable to the USB port on
Connect the USB cable to your trimmer.
When charging the LED indicator will illuminate.
Allow 14-16 hours for a complete charge.
CORDED USE
Conne ct the ch arging ad aptor to the produ ct and then to the ma ins.
When the cord is connected to the mains, a charging LED light is displayed on the trimmer.
CAUTI ON: E xtend ed mains o nly use will result i n the redu ction of t he batt ery lif e.
WARNING: The trimmer can not be operated in corded mode while connected to a
PC via the USB port.
CORDLES S USE
When the unit is switched on and fully charged, the product can be used in cordless mode
for up to 40 minutes.
HOW TO USE
BEFORE YOU BEGIN
Always comb your beard or moustache with a fine comb before you start trimming.
0.5-5.5 MM GUIDE COMB
0.5-5.5 mm guide comb
The can be adjusted to give you simply by
turning the to the desired setting. Turn the clockwise for longer length and
anticlockwise for shorter length. The setting number will appear on the length position
indicator.
ATTACHING AND REMOVING THE
With the trimmer blade facing away from you, slide the guide comb on top of the clipper
blade and click into position.
With the trimmer blade facing away from you, carefully push the guide comb away from
To attach or remove the heads press the red release button at both sides of the product.
TO THIN AND TAPER THE BEARD/MOUSTACHE (DIAGRAM 1)
Attach a guide comb to the 3 mm Trimmer Blade. If you are trimming for the first time
start with the maximum trimming length setting.
Turn the unit on.
Place the flat top of the trimmer comb against the skin.
Slowly slide the personal groomer through the hair. Repeat from different directions as
necessary.
If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull
off the comb and brush/rinse off.
TRIMMING EDGE OF SIDEBURNS(DIAGRAM 2)
Hold the personal groomer with 3 mm Trimmer Blade facing you.
Start with edge of sideburn, and with the trimmer blades resting lightly against your skin,
use motions towards edge of sideburn line to trim to desired locations in facial area.
USING THE SHAVER (DIAGRAM 3)
Attach the shaver.
Use short, well-controlled movements. Use your free hand to stretch your skin. This
encourages the hair to stand upright, making it easier to shave.
NOTE: Always trim your facial hair first before shaving.
Tips for best results
Beard, moustache and sideburn hairs should be dry.
Avoid using lotions before using your personal groomer.
Gently brush the remaining hairs away/rinse under warm water from the guide comb and
2.
trimmer blade.
CLEANING CAUTIONS
Only use the light-grade oil supplied or sewing machine oil on the blades.
Do not use harsh or corrosive cleaners on the units or their blades.
Do not submerge in water as damage will occur.
NOTE: Only rinse the shaver-/trimmer head under running water. Do not wash the whole
product as damage will occur.
STORAGE
Always store this appliance and cord in a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
Do not wrap the cord of the charging adaptor around the appliance.
CLEANING
Ensure the shaver is switched off and unplug ged from the mains outlet .
Release the head assembly from the shaver body. (DIAGR AM A)
Gently tap the shaver head on a flat sur face to remove the hair particles, and clean with
the cleaning brush supplied. (DIAGR AM B)
Never use the cleaning brush on the foils as damage may occur.
Close the shaving unit.
At regular intervals, put a drop of lubricant onto the shaving frame /head.
REPLACING THE FOIL & CUTTER
To ensure the continued highest quality performance from your shaver, we recommend
that foil and cutter are replaced regularly.
Signs that your foil and cutter need replacing:
1. Irritation: As foils get worn, you may experience skin irritation.
2. Pulling : As the cutters wear, your shave may not feel as close and you may feel your
cutter pulling your hair.
3. Wear through: You may notice that the cutters have worn through the foils.
Remove shaving head assembly by pressing the buttons on both sides of the shaver.
(DIAGRAM A)
Inser t fingernail between side of screen and head assembly. Pull away from notches.
(DIAGRAM C)
To reassemble, slide the foil into the shaving head and click into position. Only hold foil
by plastic frame to prevent damage. (DIAGRAM D)
TO REPLACE THE CUTTER
Remove head assembly as shown. (DIAGRAM A)
Grasp cutter between thumb and forefinger and pull upward. (DIAGRAM E)
Snap new cutter into top of oscillator tip.
Note : Do not press on the cutter ends as this may cause damage. (DIAGRAM E)
Replacement cutter & foil available: SP410
IMPORTANT SAFETY INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE,
OR INJ URY TO PERSONS :
An appliance should never be left unattended when plugged into a power outlet.
WARNING : Detach the hand-held part from the supply cord before cleaning it in water.
WARNING : The par ts that have to be fixed must be installed so they cannot fall into water.
Keep the power plug and cord away from heated surfaces.
Make sure the power plug and cord do not get wet.
Do not plug or unplug the product with wet hands.
Do not use the product with a damaged cord. A replacement can be obtained via our
International Service Centres.
Charge, use and store the product at a temperature between 15°C and 35°C
Always unplug from the mains when cleaning.
Only use the parts supplied with the appliance.
Keep this product out of reach of children. The use of this appliance by persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge can
give cause to hazards. Persons responsible for their safety should give explicit instructions
This appliance contains an environment ally friendly rechargeable Nickel Metal Hydride
battery. Do not dispose the appliance or the battery in the household waste as restrictions
exist in most countries. Adhere to national or local regulations for collection and disposal
that apply to your specific location. In case you are required to remove the battery from
the appliance for separate disposal see the instructions in the ‘Battery Removal’ section on
how to open the housing.
CAUTION: Do not put in fire or mutilate your batter y packs as they may burst or
release toxic materials.
For fur ther information on recycling see www.remington-europe.com
BATTERY REMOVAL
The battery must be removed from the appliance before it is scrapped.
To remove the batter y for safe disposal, please follow the instructions below:
Turn the personal groomer on and discharge all remaining power.
Remove trimmer head.
Use a screwdriver to pry the lower housing cover off the unit carefully. (DIAGRAM F)
Remove the 5 screws and take off the upper housing cover carefully. (DIAGRAM G)
Then disconnect the lead wires from the battery and take out the batteries. (DIAGRAM H)
This product has been checked and is free of defects. We warrant this product against any
defects that are due to the faulty material or workmanship for a year period from the
original date of consumer purchase. If the product should become defective within the
warranty period, we will repair any such defect or elect to replace the product or any part
of it without charge provided there is proof of purchase. This does not mean an extension
of the warrant y period.
®
In the case of a warranty simply call the Remington
This warranty is offered over and above your normal statutor y rights.
The warranty shall apply in all countries in which our produc t was sold via an authorised
dealer.
This warranty does not include shaving heads / foils and the cutters which are consumable
parts. Also, not covered is damage to the product by accident or misuse, abuse, alteration
to the product or use inconsistent with the technical and/or safety instructions required.
This warranty shall not apply if the product has been dismantled or repaired by a person
not authorised by us.