Quadra-Fire QFI30FB-C, QFI35FB-C Owner's Manual

Download

Page 1

Models:

QFI30FB-C QFI35FB-C

Owner’s Manual

Installation and Operation

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

WARNING: FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

• DO NOT store or use gasoline or other ﬂ am- mable vapors and liquids in the vicinity of this or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Leave the building immediately.

• Read, understand and follow these instructions for safe installation and operation.

DO NOT

DISCARD

• Leave this manual with party responsible for use and operation.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the ﬁ re department.

• Installation and service must be performed by a qualiﬁ ed installer, service agency, or the gas supplier.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter.

A CO detector shall be installed in the room where the appliance in installed.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 in the United States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

1Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 2

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Quadra-Fire gas ﬁ replace, an elegant and clean alternative to wood burning ﬁ replaces. The Quadra-Fire gas fireplace you have selected is designed to provide the utmost in safety, reliability, and efﬁ ciency.

As the owner of a new ﬁ replace, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all cautions and warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Quadra-Fire gas ﬁ replace will give you years of durable use and trouble-free enjoyment. Welcome to the Quadra-Fire family of ﬁ replace products!

We recommend that you record the following pertinent

Homeowner Reference Information

information about your ﬁ replace.

Model Name: ___________________________________________ Date purchased/installed: __________________

Serial Number: __________________________________________ Location on ﬁ replace: _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location

Type of Gas

Gas and Electric Information

Not for use with solid fuel. (Ne doit pas entre utilise avec un combustible solide).

Type of Gas (Sorte De Gaz):

NATURAL GAS

Minimum Minimum Permissible Permissible

Approved Approved Minimum Minimum (De (De Gaz) Gaz) AcceptableAcceptable 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Maximum Maximum Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Maximum Maximum Manifold Manifold Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Minimum Minimum Manifold Manifold Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Total Total Electrical Electrical Requirements: Requirements: 000Vac, 000Vac, 00Hz., less than 00 Amperes

ALTITUDE:ALTITUDE: 0-0000 0-0000 FT.FT. 0000-0000FT.0000-0000FT. MAX. MAX. INPUT I NPUT BTUH:BTUH: 00,00000,000 00,00000,000 MIN. MIN. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000 ORIFICE ORIFICE SIZE:SIZE: #XXXXX#XXXXX #XXXXX#XXXXX

The model information regarding your speciﬁ c ﬁ replace can be found on the rating plate usually located in the control area of the ﬁ replace.

Quadra-Fire, a brand of Hearth & Home Technologies 7571 215th Street West, Lakeville, MN 55044

This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1 in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements

locaux ou, en l’absence de tels reglements, selon les codes d’installation

ANSI Z21XX-XXXX · CSA 2.XX-MXX

Gas Gas Supply Supply for for Purposes Purposes of of Input Input Adjustment.Adjustment.

IN IN CANADACANADA

Model:Model:

(Modele):(Modele):

SerialSerial

(Serie):(Serie):

MADE MADE IN IN USAUSA

XXXXXXXXXXXXXXXX

Model Number

Serial Number

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 2

Page 3

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2



B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1 Listing and Code Approvals

A. Appliance Certiﬁ cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

B. Glass Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

C. BTU Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 6

E. Non-Combustible Materials Speciﬁ cation. . . . . . . . . . . . . . 6

F. Combustible Materials Speciﬁ cation . . . . . . . . . . . . . . . . . 6

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

D. Decorative Doors, Fronts and Surrounds . . . . . . . . . . . . . . 8

E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

F. Remote Controls, Wall Controls and Wall Switches . . . . . . 8

G. IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . . 9

H. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . 9

I. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10

J. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11

K. After Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

L. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks-Service Technician . . . . . . . . . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components . . . . . . . . . . . . . . . . . 17

5 Fireplace Size Requirements

A. Minimum Fireplace Opening . . . . . . . . . . . . . . . . . . . . . . 18

B. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 20

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 21

7 Installation Preparation

A. Inspection and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 22

B. Flue Damper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

C. Gas Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

D. Fireplace Conversion Notice . . . . . . . . . . . . . . . . . . . . . . 22

E. Electrical Outlet Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

F. Remote Control Conﬁ guration . . . . . . . . . . . . . . . . . . . . . 22

8 Installing Vent Pipe and Appliance

A. Vent Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

B. Venting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

C. Connecting Vent Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

D. Placing, Securing and Leveling the Appliance . . . . . . . . . 25

E. Installing Adaptor and Termination Cap . . . . . . . . . . . . . . 26

9 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 27

10 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

B. IntelliFireTM Plus Ignition System Wiring . . . . . . . . . . . . . . 28

C. IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . 29

D. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 29

E. Programming the RC300 to the Control Module . . . . . . . 29

11 Finishing

A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 30

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 30

C. Inspect Firebox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

12 Appliance Setup

A. Remove Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 31

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 31

C. Inspect Firebox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

D. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

E. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

F. Place the Lava Rock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

G. Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

H. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 33

I. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

J. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

13 Troubleshooting

A. IntelliFire™ Plus Ignition System . . . . . . . . . . . . . . . . . . . 40

14 Reference Materials

A. Appliance/Decorative Front Dimension Diagrams . . . . . . 42

B. Vent Kits Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

 = Contains updated information.



3Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 4

Parts Labor Gas Wood Pellet

EPA

Wood

Coal Electric Venting

XXXXXXX

All parts and material except as

covered by Conditions,

Exclusions, and Limitations

listed

Igniters, electronic components,

and glass

XXXXX Factory-installed blowers

X Firepots and burnpots

5 years 1 year X X Castings and baffles

7 years 3 years X X X

Manifold tubes,

HHT chimney and termination

years

1 year X Burners, logs and refractory

Limited

Lifetime

3 yearsXXXXX Firebox and heat exchanger

XXXXXXX

All replacement parts

beyond warranty period

Warranty Period

HHT Manufactured Appliances and Venting

1 Year

Components Covered

3 years

2 years

90 Days



B. Limited Lifetime Warranty

Hearth & Home Technologies

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

XXX

X Molded refractory panels

See conditions, exclusions, and limitations on next page.

4021-645G 2/15 Page 1 of 2

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 4

Ignition Modules

Page 5



B. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites.

• This warranty is only valid while the HHT appliance remains at the site of original installation.

• This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance resides.

• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the product.

• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this warranty.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur. This is not a flaw and is not covered under warranty.

• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.

• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.

• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/ incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the appliance.

• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.

• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.

• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of the structure.

This warranty is void if:

• The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes.

• The appliance is subjected to prolonged periods of dampness or condensation.

• There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

• The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE.

4021-645G 2/15 Page 2 of 2

5Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 6

Listing and Code Approvals

A. Appliance Certiﬁ cation

MODELS: QFI30FB-C, QFI35FB-C

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Heater

STANDARD: ANSI Z21.88-2014 • CSA 2.33-2014

This product is listed to ANSI standards for “Vented Gas Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

Quadra-Fire gas inserts are designed for installations into solid fuel masonry or factory built ﬁ replaces that have been installed in accordance with the National, Provincial, State and local building codes. Fireplaces are to be constructed of non-combustible materials and, in the absence of local or regional codes, meet criteria of NFPA 211. No additional outside air source is required.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

• In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper oriﬁ ce size.

E. Non-Combustible Materials Speciﬁ cation

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC shall be considered

non-combustible materials.

F. Combustible Materials Speciﬁ cation

Materials made of or surfaced with wood, compressed paper, plant ﬁ bers, plastics, or other material that can ignite and burn, whether ﬂ ame proofed or not, or plastered or unplastered shall be considered combustible materials.

B. Glass Speciﬁ cations

This appliance is equipped with 5 mm ceramic glass. Replace glass only with 5 mm ceramic glass. Please contact your dealer for replacement glass.

C. BTU Speciﬁ cations

Models

(U.S. or Canada)

QFI30FB-C (NG)

QFI30FB-C (LP)

QFI35FB-C (NG)

QFI35FB-C (LP)

(0-2000 FT)

CANADA

(2000-4500 FT)

(0-2000 FT)

CANADA

(2000-4500 FT)

(0-2000 FT)

CANADA

(2000-4500 FT)

(0-2000 FT)

CANADA

(2000-4500 FT)

Maximum

Input

BTU/h

36,000 17,000 33

33,250 16,750 34

36,000 19,000 50

31,000 15,500 51

40,000 20,000 31

37,000 19,250 32

38,000 19,000 49

35,000 17,000 50

Minimum

Input

BTU/h

Oriﬁ ce

Size

(DMS)

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA

70-latest edition or the Canadian Electric Code CSA C22.1.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 6

Page 7

Operating Instructions

User Guide

A. Gas Fireplace Safety

WARNING! DO NOT operate ﬁ replace before reading and understanding operating instructions. Failure

to operate ﬁ replace according to operating instructions could cause ﬁ re or injury.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

• Keep children away.

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Clothing, furniture, draperies, and other ﬂ ammable materials must not be placed on or near the appliance.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals. DO NOT operate the appliance with the barrier removed. If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns.

• A physical barrier is recommended if there are at risk

individuals in the house.

• To restrict access to a ﬁ replace or stove, install an

adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Install a switch lock or a wall/remote control with child

protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot ﬁ replace, whether

operating or cooling down.

• Teach children to NEVER touch the ﬁ replace.

• Consider not using the ﬁ replace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/safety-information

To prevent unintended operation when not using your ﬁ re- place for an extended period of time (summer months, vacation/trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Turn off gas controls valve on standing pilot models.

B. Your Fireplace

WARNING! DO NOT operate ﬁ replace before read- ing and understanding operating instructions. Failure

to operate ﬁ replace according to operating instructions could cause ﬁ re or injury.

APPLIANCE INSTALLED IN EXISTING

SOLID FUEL FIREPLACE

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.D.

FIXED GLASS ASSEMBLY

(NOT SHOWN) SECTION 12.I.

CLEAR SPACE

SECTION 2.C.

HEARTH

BATTERY BACKUP

ACCESS

SECTION 2.G.

Figure 2.1 General Operating Parts

MANTEL

SECTION 5.B.

7Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 8

C. Clear Space

WARNING! DO NOT place combustible objects in front of the ﬁ replace or block louvers. High temperatures may start a ﬁ re. See Figure 2.2.

Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects.

APPLIANCE INSTALLED IN EXISTING

SOLID FUEL FIREPLACE

3 FT. IN FRONT OF FIREPLACE

CLEAR SPACE

E. Fixed Glass Assembly

See Section 12.I.

F. Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed to operate your ﬁ replace:

For safety:

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

Figure 2.2 Clear Space

D. Decorative Doors, Fronts and Surrounds

WARNING! Risk of Fire! Install ONLY doors, fronts or surrounds approved by Hearth & Home Technologies. Unapproved doors or fronts may cause appliance to overheat.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 8

Page 9

G. IPI Battery Tray/Battery Installation

The IntelliFireTM Plus system has a battery backup option. Battery longevity and performance will be affected by the service temperatures of this appliance.

NOTICE: Batteries should only be used as a power source in the event of an emergency such as an outage.

The removable battery tray is located in the lower left corner of the appliance next to the lower glass clip. Remove batteries from tray before sliding tray back into appliance. See Figure 2.3.

A notch on the right side of the tray engages the tray with the appliance. See Figure 2.4. To remove the tray, rotate the left side of the tray outward and pull to the left to disengage the notch. Place the batteries in the tray and return it to the closed position with the notch engaged in the appliance.

Figure 2.3 Location of Battery Tray

NOTCH

H. Control Module Operation

1. The control module has an ON/OFF/REMOTE selector

switch that must be set. See Figure 2.6.

OFF Position: Appliance will ignore all power inputs and

will not respond to any commands from a wall switch or remote. The unit should be in the OFF position during installation, service, battery installation, fuel conversion, and in the event that the control goes into LOCK-OUT mode as a result of an error code.

ON Position: Appliance will ignite and run continuously

in the HI ﬂ ame setting, with no adjustment in ﬂ ame output. This mode of operation is primarily used for initial installation or power outage operation with battery backup.

REMOTE Position: Appliance will initiate commands

from an optional wired wall switch and/or the wireless remote (RC300).

2. If using a wired wall switch with the module in REMOTE

mode, the ﬂ ame output can be adjusted with the HI/LO selector switch on the module. See Figure 2.6. Note that the ﬂ ame HI/LO selector switch will become inactive once an optional remote control (RC200/RC300) is programmed to the control module. Note that the control module will always ignite the ﬁ replace on HI and remain so for the initial 10 seconds of operation. If the HI/LO is switched to the LO position, the ﬂ ame output will automatically drop to the lowest setting after the ﬂ ame has been established for 10 sec. After this 10 second period, the ﬂ ame can be adjusted from HI to LO with the switch.

3. The control module has safety feature that automatically

shuts down the ﬁ replace after 9 hours of continuous operation without receiving a command from the RC300 remote.

4. If you intend to use both an optional wired wall switch

and the RC300 remote control to operate your ﬁ replace, the wall switch will override any commands given by the remote.

Figure 2.4 Pull Left Side of Tray Out and Disengage Notch

Figure 2.5 Battery Tray Pulled Out

MODULE

FLAME HI/LOW

SWITCH

Figure 2.6 Control Module

INDICATOR LED

STATUS

SELECTOR

SWITCH

NG/LP GAS-TYPE SELECTOR SWITCH

9Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 10

5. Module Reset Switch

This module may lock-out under certain conditions.

When this occurs, the appliance will not ignite or respond to commands. The module will go into lock-out mode by emitting three audible beeps, then continuously displaying a RED/GREEN error code at its status indicator LED.

• Check battery tray. Remove batteries if installed. Batteries should only be installed for use during power outages. See Section G.

• Locate the module reset switch. (SeeFigure 2.7).

• Set the module reset switch to the RESET position.

• Wait ﬁ ve (5) minutes to allow possible accumulated gas to clear.

• Set the module reset switch to ON.

• Start the appliance.

WARNING! Risk of Explosion! DO NOT press the module reset switch more than one time within a ﬁ ve minute time period. Gas may accumulate in ﬁ rebox. Call a quali- ﬁ ed service technician.

I. Before Lighting Fireplace

Before operating this ﬁ replace for the ﬁ rst time, have a qualiﬁ ed technician:

• Verify all shipping materials have been removed from inside and/or underneath the ﬁ rebox.

• Review proper placement of logs, ember material and/ or other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire/Asphyxiation! DO NOT operate ﬁ replace with ﬁ xed glass assembly removed.

This ﬁ replace has an Intelliﬁ re

Plus ignition system.

MODULE RESET SWITCH

Figure 2.7. Module Reset Switch

Nine Hour Safety Shutdown Feature

This appliance has a safety feature that automatically shuts down the ﬁ replace after 9 hours of continuous operation without receiving a command from the RC300 remote.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 10

Page 11

J. Lighting Instructions (IPI)

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an intermittent pilot ignition (IPI) device which

automatically lights the burner. DO NOT try to light the burner by hand.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell

next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If

the knob will not push in or turn by hand, DO NOT try to repair it, call a qualiﬁ ed service technician. Force or attempted repair may result in a ﬁ re or explosion.

D. DO NOT use this appliance if any part has been under water. Immediately call

a qualiﬁ ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS (IPI)

1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2. Wait ﬁ ve (5) minutes to clear out any gas. Then smell for gas, including near the ﬂ oor. If you smell gas, STOP! Follow “B” in the Safety Information located on the

top of this label. If you do not smell gas, go to next step.

3. To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON. Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4. If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. Equipped with wall switch: Turn ON/OFF switch to OFF. Equipped with remote or wall control: Press OFF button. Equipped with thermostat: Set temperature to lowest setting.

2. Service technician should turn off electric power to the control when performing service.

DANGER

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

WARNING:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information, consult a qualiﬁ ed installer, service agency or the gas supplier.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hearth & Home Technologies ﬁ replace, please refer to www.ﬁ replaces.com.

For additional information on operating your

CAUTION:

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having ﬂ ammable vapors away.

DO NOT operate the appliance with ﬁ xed glass assembly removed, cracked or broken. Replacement of the ﬁ xed glass assembly should be done by a licensed or qualiﬁ ed service person.

NOT FOR USE WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certiﬁ ed for Installation in a Bedroom or a Bedsitting Room.

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and

Propane Installation code, CSA B149.1.

593-913i

11Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 12

K. After Appliance is Lit

Initial Break-in Procedure

• The appliance should be run three to four hours continuously on high.

• Turn the appliance off and allow it to completely cool.

• Remove ﬁ xed glass assembly. See Section 12.I.

• Clean ﬁ xed glass assembly. See Section 3.

• Replace the ﬁ xed glass assembly and run continuously on high an additional 9 hours.

This cures the materials used to manufacture the ﬁ re- place.

NOTICE! Open windows for air circulation during appliance break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

L. Frequently Asked Questions

ISSUE SOLUTIONS

Condensation on the glass

Blue ﬂ ames

Odor from appliance

Film on the glass

Metallic noise

Is it normal to see the pilot ﬂ ame burn continually?

This is a result of gas combustion and temperature variations. As the appliance warms, this condensation will disappear.

This is a result of normal operation and the ﬂ ames will begin to yellow as the appliance is al- lowed to burn for 20 to 40 minutes.

When ﬁ rst operated, this appliance may release an odor for the ﬁ rst several hours. This is caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may also be released from ﬁ nishing materials and adhesives used around the appliance.

This is a normal result of the curing process of the paint and logs. Glass should be cleaned within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing process. A non-abrasive cleaner such as gas ﬁ replace glass cleaner may be necessary. See your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the appliance.

In an intermittent pilot ignition system (IPI), the pilot ﬂ ame should turn off when appliance is turned off. Some optional control systems available with IPI models may allow pilot ﬂ ame to remain lit.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 12

Page 13

Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

When properly maintained, your appliance will give you many years of trouble-free service. We recommend annual service by a qualiﬁ ed technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualiﬁ ed techni- cian only. The appliance should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. The control compartment, burner and circulating air passageway of the appliance must be kept clean.

CAUTION! Risk of Burns! The appliance should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop

cloth and a stable work surface.

CAUTION! Handle ﬁ xed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate ﬁ xed glass assembly and door frame by placing a drop cloth on a ﬂ at, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or ﬂ oor surfaces.

• Remove door or decorative front from appliance and set aside on work surface.

• See Section 12.I for instructions to remove ﬁ xed glass assembly.

• Clean glass with a non-abrasive commercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass

cleaner (consult with your dealer)

• Carefully set ﬁ xed glass assembly in place on appliance. Hold glass in place with one hand and secure glass latches with the other hand.

• Reinstall door or decorative front.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair as necessary.

• Check that louvers are not blocked.

• Vacuum or dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote con-

trol instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

• Place batteries as needed in remote transmitters and battery-powered receivers.

• Place remote control out of reach of children.

If not using your ﬁ replace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

• Remove batteries from remote controls.

13Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 14

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

• Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

• Inspect for corrosion or separation.

• Verify weather stripping, sealing and ﬂ ashing remains intact.

• Inspect draft shield to verify it is not damaged or missing.

B. Maintenance Tasks-Service Technician

The following tasks must be performed by a qualiﬁ ed technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Service Technician

Tools needed: Protective gloves, drop cloth and a stable

work surface.

• Inspect gasket seal and its condition.

• Inspect ﬁ xed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

• Conﬁ rm there is no damage to glass or glass frame. Replace as necessary.

• Verify that ﬁ xed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

• Remove all foreign objects.

• Verify unobstructed air circulation.

Firebox

Frequency: Annually

By: Service Technician

Tools needed: Protective gloves, sandpaper, steel wool,

cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

• Replace appliance if ﬁ rebox has been perforated.

Surface cracking or crazing of ﬁ rebrick material is normal and expected. All cracks are acceptable and do not require replacement of the unit or the ﬁ rebox with the exception of:

• Cracks compromising the surface plane of the ﬁ rebox.

See Figure 3.1.

Figure 3.1 Surface plane of ﬁ rebox is comprised and should be replaced.

Logs

Frequency: Annually

By: Service Technician

Tools needed: Protective gloves.

• Inspect for damaged or missing logs. Replace as necessary. Refer to Section 12 for log placement instructions.

• Verify correct log placement and no ﬂ ame impingement causing sooting. Correct as necessary.

Control Compartment and Firebox Top

Frequency: Annually

By: Service Technician

Tools needed: Protective gloves, vacuum cleaner, dust

cloths

• Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 14

Light Bulbs

Frequency: As needed

By: Service Technician

Tools needed: Protective gloves, replacement light

bulbs. 1/4 in. nut driver.

• Remove the glass frame. See Section 12.I.

• Remove the logs, grate, and burner.

• Remove the two ember glass retainer tabs.

• Remove the ember glass.

• Replace light bulb.

• Reassemble components in reverse order of disassembly.

Page 15

Burner Ignition and Operation

Frequency: Annually

By: Service Technician

Tools needed: Protective gloves, vacuum cleaner, whisk

broom, ﬂ ashlight, voltmeter, indexed drill bit set, and a manometer.

• Verify burner is properly secured and aligned with pilot or igniter.

• Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

• Replace Glowing embers with new dime-size pieces. DO NOT block ports or obstruct lighting paths. Refer to Section 12 for proper ember placement.

• Verify batteries have been removed from battery back-up IPI systems to prevent premature degradation due to long term heat exposure.

• Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

• Inspect for lifting or other ﬂ ame problems.

• Verify air shutter setting is correct. See Section 12 for required air shutter setting. Verify air shutter is clear of dust and debris.

• Inspect oriﬁ ce for soot, dirt and corrosion. Verify oriﬁ ce size is correct. See Service Parts List for proper oriﬁ ce sizing.

• Verify manifold and inlet pressures. Adjust regulator as required.

• Inspect pilot ﬂ ame pattern and strength. See Figure 3.2 for proper pilot ﬂ ame pattern. Clean or replace oriﬁ ce spud as necessary.

• Inspect IPI ﬂ ame sensing rod for soot, corrosion and deterioration. Polish with ﬁ ne steel wool or replace as required.

• Verify that there is not a short in ﬂ ame sense circuit by checking continuity between pilot hood and ﬂ ame sense rod. Replace pilot as necessary.

Figure 3.2 IPI Pilot Flame Patterns

15Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 16

Installer Guide

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂ ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

Getting Started

VERTICAL TERMINATION CAP (SECTION 8.E)

VENT PIPE (SECTION 8)

3 INCH FLEX LINERS (SECTION 8)

GAS LINE (SECTION 9) ACCESS THROUGH EXISTING MASONRY OR WOODBURNING FIREPLACE

MANTEL AND MANTEL LEG SECTION 5.B AND 11.A

SURROUND OR FRONT NOT SHOWN

SECTION 2.D AND SECTION 8.

HEARTH EXTENSION

Figure 4.1 Typical System

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 16

Page 17

B. Design and Installation Considerations

211. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, ﬁ re ofﬁ cials or authorities having jurisdic- tion over restrictions, installation inspection and permits.

Prior to installing the gas insert:

• Have the chimney and adjacent structure inspected and cleaned by qualiﬁ ed professionals. Hearth & Home Technologies recommends that NFI or CSIA certiﬁ ed professionals, or technicians under the direction of certiﬁ ed professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

• Replace component parts of the chimney and ﬁ replace as speciﬁ ed by the professionals.

• Ensure combustible mantel and surround clearances comply with applicable codes and regulations for solidfuel ﬁ replaces. In the absence of local or regional codes, refer to NFPA 211.

• Ensure all joints are properly engaged and the chimney is properly secured.

• Minimum ﬁ replace size. See Section 5.A.

• Gas supply piping requirements.

• Electrical wiring requirements.

• Finishing details.

• Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualiﬁ ed technician, service agency or your dealer.

Installation and service of this appliance should be performed by qualiﬁ ed personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certiﬁ ed professional.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure Framing material Pliers Phillips screwdriver Gloves Framing square Voltmeter Electric drill and bits (1/4 in.) Plumb line Safety glasses Level Reciprocating saw Manometer Flat blade screwdriver Hammer Noncorrosive leak check solution 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws

Caulking material (300ºF minimum continuous exposure rating)

D. Inspect Appliance and Components

• Carefully remove the appliance and components from the packaging.

• The vent system components and decorative doors and fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate must be installed.

• Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁ t.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, in- complete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modiﬁ cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a ﬁ re hazard.

WARNING! Risk of Fire,/Explosion/Electric Shock! DO NOT use this appliance if any part has been under

water. Call a qualiﬁ ed technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

17Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 18

Fireplace Size Requirements

A. Minimum Fireplace Opening

Minimum ﬁ replace opening requirements are shown in Figure 5.2.

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• The ﬁ rebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed from a factory built ﬁ rebox in order to gain minimum gas insert opening requirements.

• Any smoke shelves, shields and bafﬂ es may be removed from the factory built ﬁ rebox if attached with mechanical fasteners.

SIDE VIEW

• The metal ﬂ oor of the solid fuel ﬁ rebox may be removed to facilitate the installation of the insert.

• Cutting of any sheet metal parts of the ﬁ replace in which the gas ﬁ replace insert is to be installed is prohibited, except the ﬂ oor as tested for and as noted above and in Figure 5.1.

• A minimum 1/2 inch gap from the bottom of the appliance to the metal ﬂ oor of the solid fuel ﬁ rebox is RECOMMENDED for optimal fan performance. See side view in Figure 5.1.

TOP VIEW

11-1/4

METAL FLOOR OF EXISTING

IN.

SOLID FUEL FIREBOX

5 IN.

1/2 IN. MINIMUM LEVELING HEIGHT

(RECOMMENDED) 1/4 IN. REQUIRED

METAL FLOOR OF EXISTING SOLID FUEL FIREBOX

Figure 5.1-A

• The appliance may not be placed directly on the base of the outer wrap, a 1/4 inch airspace MUST be provided between the insert and the ﬂ oor of the outer wrap. Use the levelling legs to raise the insert a minimum of 1/4 inch. The original ﬁ replace may never be returned to solid fuel in this condition. The sidewalls and top structure of the ﬁ rebox may not be altered with the exception of removable bafﬂ es and dampers.

Figure 5.1-B

REMOVE THIS SECTION OF METAL FLOOR

11-1/4

IN.

REMOVE THIS SECTION OF METAL FLOOR

• If the recommended 1/2 inch leveling leg height can not be achieved, a section of the factory-built metal ﬂ oor may be removed. See Figure 5.1-B.

QFI35FB-C QFI30FB-C

6 IN.

12 IN.

EXISTING FACTORY BUILT FIREBOX

6 IN.

12 IN.

5 IN.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 18

Page 19

TOP VIEW

G**

FRONT VIEW

MINIMUM FIREPLACE SIZE

QFI35FB-C QFI30FB-C

Location

Inches Millimeters Inches Millimeters

A Rear Width 25-1/2 648 21-1/2 546

B Front Width 35 889 30-1/4 768

C Glass Opening Width 31-1/2 800 26-3/4 679

D Glass Opening Height 20 508 18 457

E Height-Front 24-7/8 632 22-7/8 581

F Height-Rear 22-1/4 565 20-5/8 524

G** Unit Depth 18-1/4 464 16-7/8 429

H Venting Depth 13-3/8 340 12-1/8 308

* Note: If exhaust collar on insert and ﬁ replace damper do not line up, add 4 inches (102 mm) to minimum

ﬁ replace height for bends in vent pipe.

**Unit depth is measured to the back of the surround to give the depth needed for installation.

In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B).

Figure 5.2 Fireplace Opening

19Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 20

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as speciﬁ ed. Framing or ﬁ nishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Clearance to combustible material under the insert is 1/4 inch (6 mm). Clearance from top of ﬁ replace opening for combustibles extending 12 inches max. is 12 inches.

• Use leveling legs to raise insert minimum 1/4 inch (6 mm) above combustible material or outer wrap of factory built ﬁ rebox.

Combustible facings must not extend behind the insert surround. For non-combustible material speciﬁ cations refer to section 1.E.

EXISTING NON-COMBUSTIBLE FACING

12 IN. MAX.

12 IN. MIN.

10 IN. MIN.

2 IN. MAX.

Figure 5.3 Mantel Clearance

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 20

Page 21

Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Maintain vent clearance to combustibles as speciﬁ ed.

• DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause ﬁ re.

HORIZONTAL

OVERHANG

2 FT. MIN.

GAS DIRECT VENT TERMINATION CAP

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5*

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

ROOF PITCH

IS X/ 12

VERTICAL

WALL

21Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 22

Installation Preparation

Prepare the existing solid fuel masonry or factory built non-combustible ﬁ rebox for installation.

A. Inspection and Cleaning

Prior to installing the gas insert:

• Replace component parts of the chimney and ﬁ replace as speciﬁ ed by the professionals.

• Ensure all joints are properly engaged and the chimney is properly secured.

• Ensure combustible mantel and surround clearances comply with applicable codes and regulations for solidfuel ﬁ replaces. In the absence of local or regional codes, refer to NFPA 211.

• Ensure chimney is constructed of non-combustible materials.

• Ensure chimney is clean and in good working order.

• Ensure that all chimney cleanouts ﬁ t properly to prevent air leakage into chimney.

B. Flue Damper

Fully lock the solid fuel ﬁ replace’s ﬂ ue damper in the open position, OR completely remove it.

D. Fireplace Conversion Notice

Permanently attach the label with the following warning to the inside lower back of the ﬁ replace ﬁ rebox into which the insert is being installed. Silicone or mechanical fasteners may be required to properly secure the label.

WARNING! Risk of Fire! This ﬁ replace has been con- verted for use with a gas ﬁ replace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the ﬁ replace re-approved by the authority having jurisdiction.

E. Electrical Outlet Box

An outlet box may be installed in a bottom back corner of the existing solid fuel masonry or factory built ﬁ replace to permit blowers or other optional accessories to be used. Alternatively, the supplied power cord may be routed out onto the hearth to a nearby outlet.

F. Remote Control Conﬁ guration

The Intelliﬁ reTM Plus should be programmed to the RC300 remote control prior to the installation of the insert into the existing solid fuel masonry or factory built ﬁ replace.

The control is accessed by removing the lower access panel on the left side of the insert. See Section 10.E.

C. Gas Line

Note: If the factory built ﬁ replace has no gas access hole

provided, an access hole of 1 inch (25 mm) diameter or less may be drilled through the lower sides or bottom of the ﬁ rebox in a proper workmanship - like manner. This access hole must be plugged with non-combustible insulation after the gas supply line has been installed.

• Install gas line into ﬁ rebox cavity.

• Check local codes and gas line sizing requirements following NFPA51. See Section 9.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 22

Page 23

Installing Vent Pipe and Appliance

A. Vent Limits

The abbreviations listed in this vent table key are used in the vent diagrams.

Description

Minimum Vertical Run Length 10 ft.

Maximum Vertical Run Length 50 ft.

Horizontal venting is NOT allowed.

Vertical terminations are measured to top of chimney.

This appliance is listed for use with LINK-DV systems and components only. It is permissible to extend venting above existing chimney (within speciﬁ ed maximum verti- cal limits) using SL-D series or Dura Vent GS series 4 in. x 6-5/8 in. gas direct-vent pipe. Connection is made using DV-46DVA-GK. The vent must be terminated with the cap supplied with the LINK-series vent kit.

WARNING! Risk of Fire/Explosion/Asphyxiation! Do NOT connect this gas appliance to a chimney ﬂ ue serving a separate solid fuel or gas burning appliance.

• May impair safe operation of this appliance or other appliances connected to the ﬂ ue.

• Vent this appliance directly outside.

• Use separate vent system for this appliance.

CAUTION! ALL vent speciﬁ cations MUST be followed.

This product is tested and listed to these speciﬁ cations. Appliance performance will suffer if speciﬁ cations are not followed.

B. Venting Components

CAUTION! Risk of Cuts/Abrasions/Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

The vertical vent termination system installed on this model includes:

• One 3-foot section stainless steel ﬂ exible pipe (included with insert).

• Flexible vent pipe for exhaust air (included with vent kit).

• One length of 3-inch ﬂ exible vent pipe for combustion air (included with vent kit).

• One pipe-to-cap adaptor (included with vent kit).

• One vertical termination cap (included with vent kit).

HANDLE

ADAPTER

V = 10 FT. MINIMUM 50 FT. MAXIMUM

TERMINATION

CAP

INLET

COLLAR

EXHAUST

COLLAR

EXHAUST

AIR

VENT PIPE

INLET AIR VENT PIPE

INLET AIR STARTING COLLAR

STARTING COLLAR BRACKET

LOCKING TAB

EXHAUST STARTING COLLAR

NOTE: TO ACHIEVE OPTIMUM PERFORMANCE OF INSERT, MINIMIZE OR AVOID BENDS IN EXHAUST VENT PIPE.

INLET AIR STARTING COLLAR

STARTING COLLAR BRACKET

Figure 8.1

EXHAUST STARTING COLLAR

23Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 24

C. Connecting Vent Pipe

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Reference instructions in the termination kit.

• Install the 3-inch ﬂ exible vent pipe(s) down through the chimney.

• Secure the exhaust ﬂ exible vent pipe to the 3 foot section stainless steel flexible vent pipe using the factoryinstalled 3-inch collar in the stainless steel section of pipe (see Figure 8.1).

• Secure the stainless ﬂ exible vent pipe to the exhaust starting collar on top of the appliance with three screws.

• Use 3 screws to attach the section of inlet air vent to the inlet collar on the collar slide plate. See Figure 8.1. NOTE: The collar slide plate may be removed from appliance to aid installation.

Figure 8.2

• Trim chimney top plate to minimize excess overhang or bend over ﬂ ue tile (see Figure 8.2).

• Place 3/8 inch bead of silicone (300ºF minimum continuous exposure rating) on ﬂ ue tile top.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 24

Page 25

D. Placing, Securing and Leveling the

Appliance

WARNING! Risk of Explosion/Combustion Fumes!

Connect vent sections per installation instructions.

• The 3 foot section of stainless steel ﬂ exible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

• Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

• Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

• DO NOT allow vent to sag below connection point to appliance.

• Remove rear leveling legs from shipping position and relocate to one of the positions shown in Figure 8.3. Remove both screws that secure the leveling leg to the side of the appliance. Turn the leveling leg around so that the foot is facing out and downward. Line up the two holes on the leg with the holes on the appliance and secure with screws. See Figure 8.3.

• Front leveling legs are shipped with surround and may be installed in one of two locations. See Figure 8.3.

• Install insert (without surround attached) into existing ﬁ replace while pulling collar slide plate forward.

• Install gas line into hole provided on side.

• Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 8.1) and secure with #8 screw.

• Level the appliance from side to side and front to back. Adjust leveling bolts to desired vertical position so appliance is level. Use the leveling bolts included with the manual bag.

• A minimum 1/2 inch gap from the bottom of the appliance to a metal surface is recommended for optimal fan performance. See Figure 5.1.

• Position any excess ﬂ exible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

• Attach surround. Follow instructions for surround installation included with the front.

• Push insert into the opening so that it tightly overlaps the ﬁ replace opening.

REAR LEVELING LEGS SHIPPED IN THIS POSITION

THE FRONT LEVELING LEGS ARE SHIPPED WITH THE SURROUND. THEY SHOULD BE INSTALLED AS SHOWN.

REAR LEVELING LEGS MAY BE RELOCATED TO LOCATION A OR LOCATION B

LOCATION A

LOCATION B

FRONT LEVELING LEGS MAY BE MOVED TO THIS LOCATION

WARNING! Risk of Fire! Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning ﬁ replaces. No other com- ponents such as shrouds, sheetmetal plates, etc., may be used to seal off vents.

WARNING! Risk of Explosion! Failure to position the parts in accordance with these diagrams or failure to use only parts speciﬁ cally approved with this appliance may result in property damage or personal injury.

Figure 8.3

25Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 26

E. Installing Adaptor and Termination Cap

EXHAUST

AIR

VENT PIPE

TERMINATION

CAP

LINK-DV30B

LINKSQ-DV30

Installation

LINK-DV4-30B

LINKSQ-DV4-30

Installation

INLET AIR

VENT PIPE

WARNING:

DO NOT BLOCK

THIS PIPE END!

INLET AIR

VENT PIPE

EXHAUST

AIR

VENT PIPE

CAUTION! Risk of Cuts/Abrasions/Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 8.4) .

To install adaptor see Figure 8.5.

To prevent odors and cold drafts, the chimney must be sealed around the vent with non-combustible blanket insulation or ﬁ eld fabricated metal plates.

HORIZONTAL

OVERHANG

To help eliminate cold air drafts, it may be necessary to place non-combustible insulation around the ﬂ ues as they go though the damper.

Note: The LINK-DV4-30B and LINKSQ-DV4-30 systems REQUIRE this insulation.

2 FT. MIN.

GAS DIRECT VENT TERMINATION CAP

Roof Pitch H (Min.) Ft.

Flat to 6/12....................1.0*

Over 6/12 to 7/12 ........1.25*

Over 7/12 to 8/12 ..........1.5*

Over 8/12 to 9/12 ..........2.0*

Over 9/12 to 10/12 ........2.5*

Over 10/12 to 11/12 ..... 3.25

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

ROOF PITCH

VERTICAL

WALL

IS X/ 12

Roof Pitch H (Min.) Ft.

Over 11/12 to 12/12 ....... 4.0

Over 12/12 to 14/12 ....... 5.0

Over 14/12 to 16/12 ....... 6.0

Over 16/12 to 18/12 ....... 7.0

Over 18/12 to 20/12 ....... 7.5

Over 20/12 to 21/12 ....... 8.0

* 3 foot minimum in snow regions

Figure 8.4 Minimum Height from Roof to Lowest Discharge Opening

Masonry

Factory Built

Wood Burning

OR

Figure 8.6

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 26

OPTIONAL LINK-ZC-ADPB

FOR USE WITH CLASS A

WOODBURNING PIPE

Note: Untwist the pipe while extending it, to achieve full 30’ length.

Remove 18 inch x 18 inch ﬂ ashing on cap by removing 3 screws. Connect both the LINK-ZC-ADPB to Class A Pipe and the termination cap to the LINK-ZC-ADPB with the self tapping screws provided.

Page 27

Gas Information

A. Fuel Conversion

• Make sure the appliance is compatible with available gas types.

• Conversions must be made by a qualiﬁ ed technician (NFI certiﬁ ed or factory-trained) using Hearth & Home Technologies speciﬁ ed and approved parts.

B. Gas Pressure

• Optimum appliance performance requires proper input pressures.

• Gas line sizing requirements will be determined in ANSI Z221.3 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

• Pressure requirements are:

Gas Pressure Natural Gas Propane

Minimum inlet pressure 5.0 in. w.c. 11.0 in. w.c.

Maximum inlet pressure 10.0 in. w.c. 13.0 in. w.c.

Manifold pressure 3.5 in. w.c. 10.0 in. w.c.

WARNING! Risk of Fire/Explosion! High pressure will damage valve. Low pressure may cause explosion.

• Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk.

Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

• Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

C. Gas Connection

• Refer to Reference Section 14 for location of gas line access in appliance.

• Gas line may be run through knockout(s) provided.

• The gap between supply piping and gas access hole may be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air inﬁ ltration.

• Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

• Pipe incoming gas line into valve compartment.

• Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire/Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire/Explosion! Gas build-up during line purge could ignite.

• Purge should be performed by technician certiﬁ ed by

NFI or factory-trained.

• Ensure adequate ventilation.

• Ensure there are no ignition sources such as sparks

or open ﬂ ames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all ﬁ ttings and connections with a non-corrosive commercially available leak-check solution. DO NOT use open ﬂ ame. Fittings and connections could have loos- ened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualiﬁ ed installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm) T-handle manual shut-off valve and ﬂ exible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

• If substituting for these components, please consult local codes for compliance.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce burner oriﬁ ce 4% for each 1000 feet above 2000 feet.

• In the CANADA: Reduce burner oriﬁ ce 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

27Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 28

Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.

• This appliance comes with a 110-120 VAC cord assembly. This is required for proper operation of the appliance (IntelliFire Ignition). An outlet box may be installed in a bottom back corner of the existing solid fuel masonry or factory built ﬁ replace to plug in the cord assembly, or the supplied power cord may be routed out onto the hearth to a nearby outlet.

• A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

• Low voltage and 110-120 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110-120 VAC to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

B. IntelliFireTM Plus Ignition System Wiring

• Wire an outlet box (110-120 VAC) in the bottom back corner of the existing solid fuel masonry or factory built ﬁ replace to plug in the cord assembly, or the supplied cord assembly may be rerouted out onto the hearth to a nearby outlet for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

• Refer to Figure 10.1, IPI Wiring Diagram.

• This appliance is equipped with an IntelliFireTM Plus control valve which operates on a 6 volt system.

• Plug the 6 volt transformer plug into the appliance cord assembly to supply power to the unit OR install 4 AA cell batteries (not included) into the battery tray before use. See Section 2.G for instructions on locating battery tray and installing batteries.

• Battery longevity and performance will be affected by the service temperatures of this appliance. Batteries should only be used as a power source in the event of an emergency such as an outage.

MODULE RESET

SWITCH

TO CORD ASSEMBLY

120VAC

WIRE ASSEMBLY

ORANGE

(PILOT)

INTERMITTENT PILOT IGNITOR

GREEN

(MAIN)

GROUND

MODULE

ORG WHT

AUX WIRE EXTENSION

BLACK

RED

BROWN

BATTERY PACK

6V DC (AA X 4)

EMC FILTER UNIT

RC300 4.5V DC (AAA X 3)

AUX 300

MODULE

FAN

AUX1 AUX2

TO CORD ASSEMBLY

LIGHT WIRE ASSEMBLY

ACCENT SOCKETS (2)

OPTIONAL

AUX2 NOT USED FOR INSERT MODELS. PROTECTIVE COVER INCLUDED.

120VAC

EMBER BULB 50W (2)

Figure 10.1 IPI Wiring Diagram

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 28

NOTE: SEE FIGURE 10.3 FOR ADDITIONAL INFORMATION

Page 29

C. IPI Battery Tray/Battery Installation

The IntelliFireTM Plus system has a battery backup option. Batteries should only be placed in the battery pack when 110-120 VAC is not available. See Section 2.G.

D. Control Module Operation

See Section 2.H for control module operation instructions.

Note: if any of the original wire as supplied with the appliance must be replaced, it must be replaced with type 105 °C rated wire.

E. Programming the RC300 to the Control

Module

CAUTION! Risk of burns! DO NOT program the remote control to the control module when ﬁ replace is hot.

• Refer to the RC300 Installation Instructions included in appliance manual bag to program the RC300 to the control module.

;

BLOWERS





PLUG INTO 120V EXISTING OUTLET

ORANGE - TO VALVE GROUND - TO VALVE BRACKET

GREEN - TO VALVE

, 0

BRN

(

TO IPI MODULE

RED

BLK

WHT

GRN

BLK

GRN

BLK

PLUG INTO

EXISTING

OUTLET

FUSE WIRE ASSEMBLY

FUSE WIRE

ASSEMBLY

BLK

GRN

BLK

BLOWERS

BLK

GRN

BLK

Figure 10.2 Fan Wiring Diagram

29Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 30

Finishing

A. Mantel and Wall Projections

Clearance to combustible material under the insert is 1/4 inch (6 mm). Clearance from top of ﬁ replace opening for combustibles extending 12 inches max. is 12 inches.

• Use leveling legs to raise insert minimum 1/4 inch (6 mm) above combustible material or outer wrap of factory built ﬁ rebox.

Combustible facings must not extend behind the insert surround. For non-combustible material speciﬁ cations refer to section 1.E.

EXISTING NON-COMBUSTIBLE FACING

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁ rebox. Remove metal panels covering electrical components on sides of appliance.

C. Inspect Firebox

Surface cracking or crazing of ﬁ rebrick material is normal and expected. All cracks are acceptable and do not require replacement of the unit or the ﬁ rebox with the exception of:

• Cracks compromising the surface plane of the ﬁ rebox.

See Figure 11.5.

Figure 11.1 Mantel Clearance

12 IN. MAX.

12 IN. MIN.

10 IN. MIN.

2 IN. MAX.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 30

Page 31

Appliance Setup

A. Remove Glass Assembly

See Section 12.I.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁ rebox. Remove metal panels covering electrical components on sides of appliance.

C. Inspect Firebox

Surface cracking or crazing of ﬁ rebrick material is normal and expected. All cracks are acceptable and do not require replacement of the unit or the ﬁ rebox with the exception of:

• Cracks compromising the surface plane of the ﬁ rebox.

See Figure 12.1.

F. Place the Lava Rock

WARNING! Risk of Explosion! Follow lava rock placement instructions in manual. DO NOT place lava rock on burner. Improperly placed lava rock interferes with proper burner operation.

Lava rock is shipped with this gas appliance. To place the lava rock:

• Lava rock CANNOT be placed on the burner.

• Place lava rock in front of and to the sides of the burner.

PLACE LAVA ROCK IN GRAY AREA ONLY

Figure 12.1 Surface plane of ﬁ rebox is comprised and should be replaced.

D. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁ rebox or underneath in the control cavity.

E. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

Figure 12.2 Placement of Lava Rock

31Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 32

G. Ember Placement

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place the ember material:

• Embers CANNOT be placed directly over ports. Care

should be taken not to cover the lighting trail of ports (from back to front).

• Place dime-size pieces of Glowing Embers® just in front

of the port trail, but not on or in between the ports. See Figure 12.3 (QFI30FB-C) or Figure 12.4 (QFI35FB-C). Care should be taken so that the ports are not covered. Failure to follow this procedure will likely cause lighting and sooting problems.

• Save the remaining ember materials for use during

appliance servicing. The embers provided should be enough for 3 to 5 applications.

EMBERS NOT ALLOWED IN PILOT AREA

Figure 12.3 Placement of Embers (QFI30FB-C)

EMBERS NOT ALLOWED IN PILOT AREA

Figure 12.4 Placement of Embers (QFI35FB-C)

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 32

Page 33

H. Install the Log Assembly

GRATE TINES

PILOT BRACKET

LOG PINS

LIGHT TRAYS

GRATE BAR

GLASS ROCK

LOG RESTS AGAINST BACK OF FIREBOX

CENTER LOG OVER PILOT BRACKET

FLAT SPOT FOR LOG #6

RECESSED AREA OF LOG MATES WITH BURNER TOP

SRV2221-703

SRV2221-701

SRV2221-704

SRV2221-707

SRV2221-705

SRV2221-706

SRV2221-702

Log Set Assembly: LOGS-QFI30FB Models: QFI30FB, QFI30FB-C

SRV2221-707

SRV2221-704

SRV2221-701

SRV2221-703

PILOT BRACKET

SRV2221-705

SRV2221-706

SRV2221-702

Figure 1. Logs Installed

GLASS ROCK

LIGHT TRAYS

LOG PINS

GRATE BAR

GRATE TINES

Figure 2. Reference Points for Log Placement

CAUTION: Logs are fragile, handle with care. Glass Rock (2201-853):Fill each light tray evenly with the glass rock.

LOG RESTS AGAINST BACK OF FIREBOX

CENTER LOG OVER PILOT BRACKET

Figure 3. Install Glass Rock

FLAT SPOT FOR LOG #6

RECESSED AREA OF LOG MATES WITH BURNER TOP

Figure 4. Place Log #1 Figure 5. Place Log #2

Log #1 (SRV2221-703): Position Log #1 as shown in Figure 4. See Figure 2 for additional points of reference. Center the

log over the pilot bracket. Pull the log forward until contact is made with burner.

Log #2 (SRV2221-701): Position Log #2 as shown in Figure 5. See Figure 2 and Figure 6 for additional points of reference. The recessed area on the bottom of the log and the back right corner of the burner top mate.

33Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 34

MATE LOG PIN WITH LOG SLOT

FRONT

RECESSED AREA

BACK

FLAT SPOT

FOR LOG #5

LOG TOUCHES

FIREBOX

BASE OF GRATE TINE FITS IN GROOVE

BASE TINE

MATE GRATE TINE WITH LOG SLOT

GRATE TINE SLOT

LOG PIN SLOT

FRONT

BACK

FLAT SPOT FOR LOG #6

LOG GROOVE FOR LOG #7

RIGHT

LEFT

RECESSED AREA

BACK

FLAT SPOT

FOR LOG #5

LOG TOUCHES

FIREBOX

Figure 6. Log #2

Log #3 (SRV2221-702): Position Log #3 as shown in Figure 7. See Figure 2 and Figure 8 for additional reference points.

Mate the base of the left grate tine with the groove located on the bottom of the log. Pull the log forward until it stops against the vertical portion of the grate tine. Swing the rear of the log counterclockwise until it touches the ﬁ rebox.

BASE OF GRATE TINE FITS IN GROOVE

BASE TINE

BACK

Figure 8. Log #3 - Bottom View Figure 9. Place Log #4

Log #4 (SRV2221-706): Position Log #4 as shown in Figure 9. See Figure 2 and Figure 10 for additional references. Mate

the grate tine slot with the base of the right grate tine. The grate tine slot is located on the bottom right end of Log #4. See Figure 10. Slide the right end of the log forward until the tine fully engages the slot. Mate the log pin slot with the right log pin.

FRONT

Figure 7. Place Log #3

MATE LOG PIN WITH LOG SLOT

MATE GRATE TINE WITH LOG SLOT

GRATE TINE SLOT

RIGHT

Figure 10. Log #4 - Bottom View

Log #5 (SRV2221-704): Position Log #5 as shown in Figure 11. See Figure 2 and Figure 12 for additional references. Rest

the left end of Log #5 on the ﬂ at spot indicated in Figure 7. Mate the slot, located on the bottom of the log, with the left log pin. Ensure the nose of the log does not cover any burner ports.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 34

LOG PIN SLOT

LEFT

LOG GROOVE FOR LOG #7

Figure 11. Place Log #5

FLAT SPOT FOR LOG #6

Page 35

PLACE END OF LOG

ON FLAT SPOT

PLACE END OF LOG ON FLAT SPOT

REST END OF LOG ON THE LEFT SIDE OF KNOT

KNOT

ON FLAT SPOT

PLACE END OF LOG ON FLAT SPOT

Figure 12. Place Log #6

Log #6 (SRV2221-705): Position Log #6 as shown in Figure 12. See Figures 2, 5 and 11 for additional reference points.

Place the front end of log #6 n the ﬂ at spot indicated in Figure 11. Place the back end of Log #6 on the ﬂ at spot indicated in Figure 5.

REST END OF LOG ON THE LEFT SIDE OF KNOT

PLACE END OF LOG ON FLAT SPOT

KNOT

Figure 13. Place Log #7

Log #7 (SRV2221-707): Position Log #7 as shown in Figure 13. See Figure 2 and 11 for additional reference points. Place

the front end of Log #7 on the ﬂ at spot indicated in Figure 11. Place the back end of Log #7 on the left side of the knot. See Figure 13.

2221-935C

35Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 36

H. Install the Log Assembly

GRATE TINES

PILOT BRACKET

LOG PINS

LIGHT TRAYS

LOG SUPPORTS

GRATE BAR

GLASS ROCK

FLAT SPOT

FOR LOG #7

FLAT SPOT

FOR LOG #6

LOG #1 CONTACTS BURNER

LEDGE AT TWO POINTS

CENTER LOG CUT OUT OVER PILOT BRACKET

LOG #2 TOUCHES LOG #1 HERE

LOG #2 CONTACTS

RIGHT FIREBOX WALL

BURNER LEDGE

SRV2223-703

SRV2223-701

SRV2223-702

SRV2223-704

SRV2223-706

SRV2223-705

SRV2223-707

Log Set Assembly: LOGS-QFI35FB Models: QFI35FB, QFI35FB-C

SRV2223-701

SRV2223-704

SRV2223-705

BURNER LEDGE

GRATE BAR

SRV2223-703

SRV2223-702

SRV2223-706

PILOT BRACKET

LIGHT TRAYS

LOG PINS

SRV2223-707

LOG SUPPORTS

BURNER LEDGE

Figure 1. Logs Installed

GLASS ROCK

GRATE TINES

Figure 2. Reference Points for Log Placement

CAUTION: Logs are fragile, handle with care.

Glass Rock (2201-853): Fill each light tray evenly with the glass rock.

WARNING! Risk of Explosion! DO NOT place glass rock on the burner surface. DO NOT place glass rock directly over burner ports. Improperly placed glass rock interferes with proper burner operation.

FLAT SPOT

FOR LOG #7

LOG #1 CONTACTS BURNER

LEDGE AT TWO POINTS

CENTER LOG CUT OUT OVER PILOT BRACKET

Figure 4. Place Log #1 Figure 5. Place Log #2

Log #1 (SRV2223-703): Position Log #1 as shown in Figure 4. See Figure 2 for additional points of reference. Center the

log over the pilot bracket. The log should rest on the burner ledge as shown in Figure 4.

Log #2 (SRV2223-701): Position Log #2 as shown in Figure 5. See Figure 2 for additional points of reference. Place the left end of the log on the rear log support. Slide the log back until it rest against the back of the log support. The left end of the log should touch Log #1. Swing the right end of the log counterclockwise until it contacts the right refractory wall.

Figure 3. Install Glass Rock

LOG #2 TOUCHES LOG #1 HERE

FLAT SPOT

FOR LOG #6

LOG #2 CONTACTS

RIGHT FIREBOX WALL

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 36

Page 37

MATE LOG PIN

WITH LOG SLOT

GRATE TINE GROOVE

FRONT

BACK

BURNER TOP GROOVE

LOG PIN SLOT

LOG CONTACTS

GRATE BAR

RIGHT

LEFT

REST ENDS OF LOGS

ON THE FLAT SPOTS

FLAT SPOT

FOR LOG #5

FLAT SPOT

FOR LOG #7

FLAT SPOT

FOR LOG #6

USE LOG PIN TO

LOCATE LOG

LINE SHOWS BACK

EDGE OF GRATE BAR

LOG #3 TOUCHES GRATE TINE

MATE GROOVE WITH

CORNER OF BURNER TOP

REST LOG ON

FLAT SPOT

LOG #3 TOUCHES GRATE TINE

BURNER TOP GROOVE

GRATE TINE GROOVE

FRONT

Figure 6. Log #3 - Bottom View

Log #3 (SRV2223-702): Position Log #3 as shown in Figure 7. See Figure 2 and Figure 6 for additional references. Mate

the grate tine groove with the base of the left grate tine. Slide the log forward until it stops against the vertical portion of the left grate tine. Mate the burner top groove with the left edge of the burner top as shown in Figure 7.

LOG PIN SLOT

BACK

Figure 7. Place Log #3

FOR LOG #5

MATE GROOVE WITH

CORNER OF BURNER TOP

MATE LOG PIN

WITH LOG SLOT

LOG CONTACTS

LEFT

Figure 8. Log #4 - Bottom View Figure 9. Place Log #4

Log #4 (SRV2223-706): Position Log #4 as shown in Figure 9. See Figure 2 and Figure 8 for additional references. Mate

the slot located at the left end of log #4, shown in Figure 8, with the right log pin. Rotate the right end of the log clockwise, until the log contacts the grate bar.

FLAT SPOT

FOR LOG #7

REST LOG ON

FLAT SPOT

LINE SHOWS BACK

EDGE OF GRATE BAR

FLAT SPOT

FOR LOG #6

USE LOG PIN TO

RIGHT

LOCATE LOG

REST ENDS OF LOGS

ON THE FLAT SPOTS

GRATE BAR

Figure 10. Place Log #5

Log #5 (SRV2223-704): Position Log #5 as shown in Figure 10. See Figure 2 and Figure 7 for additional references. Rest

the left end of the log on the ﬂ at spot of log #3. Locate the groove located on the right end of the log. Mate the groove with the grate bar. Use the left log pin to positively locate the right end of the log.

Log #6 (SRV2223-705): Position Log #6 as shown in Figure 11. See Figures 2, 5 and 10 for additional reference points. Place the front and back ends of the log on the ﬂ at spots as shown in Figure 11.

Figure 11. Place Log #6

37Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 38

PLACE END OF LOG ON FLAT SPOT

REST END OF LOG

ON THE LEFT SIDE OF KNOT

KNOT

ON THE LEFT SIDE OF KNOT

KNOT

PLACE END OF LOG ON FLAT SPOT

Figure 12. Place Log #7

Log #7 (SRV2221-707): Position Log #7 as shown in Figure 12. See Figure 2 and 10 for additional reference points. Place

the front and back ends of the log on the ﬂ at spots as shown in Figure 12.

2223-935C

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 38

Page 39

I. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle ﬁ xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

• DO NOT strike, slam or scratch glass.

• DO NOT operate ﬁ replace with glass removed, cracked,

broken or scratched.

• Replace as a complete assembly.

Removing Fixed Glass Assembly

• The glass assembly fastens to the ﬁ replace in four

places. The fastening mechanisms are spring-loaded glass latches. An example of the glass latch is shown in Figure 12.2.

• To release glass assembly, pull the two top spring-

loaded latches forward and allow them to retract away from the glass assembly. Slide the glass assembly outward and downward until top of the glass

frame will clear the surround.

J. Air Shutter Setting

Air shutter settings should be adjusted by a qualiﬁ ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 12.3.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

AIR SHUTTER

Replacing Fixed Glass Assembly

• Tilt glass assembly toward ﬁ replace and slide glass

assembly downward to engage bottom latches. Verify bottom latches are fully engaged and then fasten the two top latches.

• Note that the extended glass latch tabs on the glass

frame are for the bottom glass latches.

LATCHES

(BOTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

Figure 12.3 Air Shutter

Air Shutter Settings

NG LP

QFI30FB-C 1/4 in. Full Open

QFI35FB-C 1/4 in. Full Open

Figure 12.2 Fixed Glass Assembly

39Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 40

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualiﬁ ed technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualiﬁ ed technician. Contact your dealer to arrange a service call by a qualiﬁ ed technician.

Troubleshooting

A. IntelliFire™ Plus Ignition System

Symptom Possible Cause Corrective Action

1. Pilot won’t light. The ignitor/module makes noise, but no spark.

2. Pilot won’t light, there is no noise or spark.

3. Pilot sparks, but Pilot will not light.

A. Incorrect wiring. Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

connected to correct terminals on module and pilot assembly.

B. Loose connections or electrical

shorts in the wiring.

C. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be

A. No power, transformer installed

incorrectly, or depleted batteries.

B. A shorted or loose connection in

wiring conﬁ guration or wiring har- ness.

C. Improper wall switch wiring. Verify that 110-120 VAC power is “ON” to junction box.

D. Module not grounded. Verify black ground wire from module wire harness is grounded to

A. Gas supply. Verify that incoming gas line ball valve is “open”. Verify that inlet

Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly are tight; also verify igniter and ﬂ ame sense wires are not grounding out to metal chassis, pilot burner, pilot enclosure, mesh screen if present, or any other metal object.

approximately .17 in. or 1/8 in. (3 mm).

Verify that transformer is installed and plugged into module. Check voltage of transformer at connection to module. Acceptable readings of a good transformer are between 6.4 and 6.6 volts DC. Battery power supply voltage must be at least 4 volts. If below 4 volts, replace batteries.

Remove and reinstall the wiring harness that plugs into module. Verify there is a tight ﬁ t. Verify pilot assembly wiring to module. Re- move and verify continuity of each wire in wiring harness. Replace any damaged components.

metal chassis of appliance.

pressure reading is within acceptable limits.

B. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be

C. Module is not grounded. Verify module is securely grounded to metal chassis of appliance.

D. Pilot valve solenoid Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 40

approximately .17 in. or 1/8 in. (3 mm).

If below 1.5 volts, replace module. If 1.5 volts or greater, replace valve.

Page 41

Troubleshooting (continued)

Symptom Possible Cause Corrective Action

4. Pilot lights but con-

tinues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot ﬂ ame has been lit, ﬂ ame rectiﬁ cation has not occurred.)

A. A shorted or loose connection in

ﬂ ame sensing rod.

B. Poor ﬂ ame rectiﬁ cation or contami-

nated ﬂ ame sensing rod.

C. Module is not grounded. Verify module is securely grounded to metal chassis of appliance.

D. Damaged pilot assembly or con-

taminated ﬂ ame sensing rod.

Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify ﬂ ame sense or ig- niter wires are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal object.

With ﬁ xed glass assembly in place, verify that ﬂ ame is engulﬁ ng ﬂ ame sensing rod on left side of pilot hood. Flame sensing rod should glow shortly after ignition. With a multi-meter, verify that current in series between module and sense lead is at least 0.14 microamps. Verify correct pilot oriﬁ ce is installed and gas inlet is set to pressure speciﬁ cations. Polish ﬂ ame sensing rod with ﬁ ne steel wool to remove any contaminants that may have accumulated on ﬂ ame sensing rod.

Verify that wire harness is ﬁ rmly connected to the module.

Verify that ceramic insulator around the ﬂ ame sensing rod is not cracked, damaged, or loose. Verify connection from ﬂ ame sensing rod to white sensor wire. Polish ﬂ ame sensing rod with ﬁ ne steel wool to remove any contaminants that may have accumulated on ﬂ ame sensing rod. Verify continuity with a multi-meter with ohms set at lowest range. Replace pilot if any damage is detected.

41Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 42

Reference Materials

A. Appliance/Decorative Front Dimension Diagrams

Dimensions are actual appliance dimensions. Use for reference only.

MODEL DIMENSIONS

Location

A 33-13/16 859 29-3/8 746

B 24-15/16 633 20-15/16 532

C 10-11/16 271 8-11/16 221

D 3-11/16 94 3-11/16 94

E 4-3/8 111 4-1/4 108

F 13-3/8 340 11-7/8 302

G 6-9/16 167 5-3/4 146

H 33-7/8 860 29-3/16 741

I 6-3/4 172 6-3/4 172

J 12 305 10-1/2 267

K 1-5/16 33 1-5/16 33

QFI35FB-C QFI30FB-C

Inches Millimeters Inches Millimeters

MODEL DIMENSIONS

Location

L 1-7/8 48 1-7/8 48

M 1-1/2 38 1-1/2 38

N 5-7/16 138 4-1/2 114

O 16-5/8 422 15-1/8 384

P 24-3/8 619 22-5/16 567

Q 19-7/8 505 17-7/8 454

R 31-3/8 797 26-11/16 678

S 2-5/16 59 2-1/4 57

T 1-1/4 32 1-1/4 32

U 10-5/16 262 9-13/16 249

V 6-1/4 159 5-5/16 135

W 21-3/4 552 19-15/16 506

QFI35FB-C QFI30FB-C

Inches Millimeters Inches Millimeters

*Note: Location O on Figure 14.1 is measuring the appliance depth, for installation depth reference Location G on Figure 5.2.

Figure 14.1 Appliance Dimensions



Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 42

Page 43

FS-QFI30FB, FS-QFI35FB DECORATIVE FRONTS

FS-QFI30FB

FS-QFI35FB

ABC D E F G

in. 26-7/8 17-7/8 2-1/4 36-1/2 25-7/16 25 7/16

mm 683 454 57 927 646 635 11

in. 31-7/16 20 2-3/16 38-7/16 27-7/16 27 7/16

mm 799 508 56 976 697 686 11

FSL-QFI30FB, FSL-QFI35FB DECORATIVE FRONTS

FSL-QFI30FB

FSL-QFI35FB

ABC D E F G

in. 28-7/16 19-7/16 2-3/4 36-1/2 25-1/2 25 1/2

mm 722 493 70 927 648 635 13

in. 30-7/16 21-7/16 2-3/4 38-1/2 27-1/2 27 1/2

mm 773 545 70 978 699 686 13

Figure 14.2 Decorative Front Dimensions - FS-QFI30FB/FS-QFI35FB and FSL-QFI30FB/FSL-QFI35FB

43Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 44

TP-QFI30FB, TPQFI35FB DECORATIVE FRONTS

TP-QFI30FB

TP-QFI35FB

ABC D E F G

in. 32-1/2 15 4-7/8 36-9/16 26-1/2 26 1/2

mm 826 381 124 929 673 660 13

in. 34-1/2 16-7/8 4-7/8 38-9/16 28-1/2 28 1/2

mm 876 429 124 979 724 711 13

TB-QFI30FB/TB-QFI35FB DECORATIVE FRONTS

TB-QFI30FB

TB-QFI35FB

Figure 14.3 Decorative Front Dimensions - TP-QFI30FB/TP-QFI35FB and TB-QFI30FB/TB-QFI35FB

in. 28-13/16 16-5/16 5 36-1/2 25-1/2 25 1/2

mm 732 414 127 927 648 635 13

in. 30-13/16 18-5/16 5 38-1/2 27-1/2 27 1/2

mm 783 465 127 978 699 686 13

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 44

ABC D E F G

Page 45

B. Vent Kits Components

Direct Vent Flex Liner Kits (see Figure 14.4)

LINK-DV30B: Masonry 3 inch ﬂ ex liner kit. Expands to 30 feet. Includes: two liners, termination cap and ﬂ ashing.

LINK-DV4-30B: Masonry 3 inch ﬂ ex liner kit. Expands to 30 feet and 4 feet respectively. Includes: two liners, termination cap and ﬂ ashing.

LINKSQC-DV30, LINKSQB-DV30: Masonry 3 inch ﬂ ex liner kit. Expands to 30 feet. Includes: two liners, termination cap and ﬂ ashing.

LINKSQC-DV4-30, LINKSQB-DV4-30: Masonry 3 inch ﬂ ex liner kit. Expands to 30 feet and 4 feet respectively. Includes: two liners, termination cap and ﬂ ashing.

LINK-ZC-ADPB

DV-46DVA-GK

LINK-DV30B

LINK-DV4-30B

Figure 14.4 Direct Vent Flex Liner Kits

LINKSQC-DV30 (COPPER)

LINKSQB-DV30 (BLACK)

LINKSQC-DV4-30 (COPPER)

LINKSQB-DV4-30 (BLACK)

Direct Vent Flex Liner Accessory Kits (see Figure 14.5)

LINK-ZC-ADPB: Zero clearance chimney adapter

DV-46DVA-GK: Adapter kit - It is permissible to use DV46DVA-GK to connect collinear ﬂ ex vent to SL-D vent pipe to extend the run.

FLEX3-30: One 3 inch ﬂ exible liner expands to 30 feet.

FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner, one connector per kit.

FLEX3-30

FLEX-CNCT

Figure 14.5 Direct Vent Flex Liner Accessory Kits

45Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 46

C. Service Parts

Service Parts

QFI30FB-C

Log Set Assembly

30” Gas Insert - DV

Beginning Manufacturing Date: Aug 2011

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or

distributor. model number and serial number when requesting service parts from your dealer or distributor.

Hearth and Home Technologies does not sell directly to consumers. Provide

Stocked

at Depot

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Assembly LOGS-QFI30FB

1 Log 1 SRV2221-701

2 Log 2 SRV2221-702

3 Log 3 SRV2221-703

4 Log 4 SRV2221-704

5 Log 5 SRV2221-705

6 Log 6 SRV2221-706

7 Log 7 SRV2221-707

8 Termination Plate Assembly 2201-012

Gasket, Termination Plate 2201-401

Slide Plate Handle 2019-201

9 Module Bracket 2201-137

13 Glass Door Assembly GLA-2201

14 Power Cord Assembly 2201-024

15 Valve Assembly Refer to valve page

16 Aux Bracket 2201-157

17 RIV-NUT Backet Assembly Qty 2 req

18 Blower Assembly GFK-210-C

Additional service part numbers on following page. 2/15

Burner Assembly

Media Tray

Grate Assembly 2221-016

Cover Plate, Back 2202-104

2221-009

2201-112

2201-027

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 46

Page 47

Service Parts

QFI35FB-C

35” Gas Insert - Dv

Log Set Assembly

Beginning Manufacturing Date: Aug 2011

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or

distributor. model number and serial number when requesting service parts from your dealer or distributor.

ITEM DESCRIPTION COMMENTS PART NUMBER

13 Glass Door Assembly

14 Power Cord Assembly

15 Valve Assembly

16 Aux Bracket

17 RIV-NUT Backet Assembly Qty 2 req 2201-027

18 Blower Assembly

19 Cover Plate, Back

Additional service part numbers on following page. 2/15

Hearth and Home Technologies does not sell directly to consumers. Provide

Log Assembly

1 Log 1

2 Log 2

3 Log 3

4 Log 4

5 Log 5

6 Log 6

7 Log 7

8 Slide Plate Assembly

Gasket, Termination Plate

Slide Plate Handle

9 Module Bracket

Burner 2223-009 Y

Media Tray 2202-112

Grate Assembly

LOGS-QFI35FB Y

SRV2223-703

SRV2223-701

SRV2223-702

SRV2223-706

SRV2223-704

SRV2223-705

SRV2221-707

2202-012

2201-401

2019-201

2201-137

2223-016

GLA-2202 Y

2201-024

Refer to valve page

2201-157

GFK-210-C

2202-104

Stocked at Depot

47Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 48

#15 Valve Assembly

Service Parts

15.2

QFI30FB-C, QFI35FB-C

Beginning Manufacturing Date: Aug 2011

Ending Manufacturing Date: Active

15.1

15.18

15.16

15.17

15.15

15.14

15.13

15.12

15.9

15.10

15.11

15.4

15.6

15.3

15.5

15.7

15.8

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or

distributor. model number and serial number when requesting service parts from your dealer or distributor.

ITEM DESCRIPTION COMMENTS PART NUMBER

15.1

15.2

15.3

15.4

15.5 Valve Bracket

15.6

15.7 Air Passage Divider

15.8

15.9 Light Wire Assembly

15.10 Jumper Wire, Wall Switch

15.11 Transformer, 6 Volt Wall

15.12 Auxilliary Box

15.13 **Battery Pack

15.14 Module

15.15 Wire Assembly

15.16 Pilot Bracket

15.17 Air Scoop

15.18 Ember Glass

**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 250v, 1A fuse, 3/4" long

Additional service part numbers on following page.

Hearth and Home Technologies does not sell directly to consumers. Provide

Pilot Assembly NG

Pilot Assembly LP

Burner Oriﬁ ce NG (#33C)

Burner Oriﬁ ce LP (#50C)

Burner Oriﬁ ce NG (#31C)

Burner Oriﬁ ce LP (#49C)

Flex Assembly

Flex Ball Valve Assembly

Valve NG

Valve LP

Ember Bulb

QFI30FB-C

QFI35FB-C

QFI30FB-C 2201-144

QFI35FB-C 2202-144

Qty 2 req 2201-150 Y

2202-013 Y

2202-014 Y

582-833 Y

582-850 Y

582-831 Y

582-849

383-302A Y

2201-108 Y

2202-108

2166-302 Y

2166-303 Y

2201-011 Y

2179-300 Y

2326-131 Y

2166-335 Y

2166-323 Y

2166-307 Y

2201-304 Y

2201-025

2201-156

2201-115 Y

Stocked at Depot

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 48

Page 49

Service Parts

QFI30FB-C, QFI35FB-C

Beginning Manufacturing Date: Aug 2011

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or

distributor. model number and serial number when requesting service parts from your dealer or distributor.

Hearth and Home Technologies does not sell directly to consumers. Provide

ITEM DESCRIPTION COMMENTS PART NUMBER

Ember Rocks 2201-853

Fan Wire Assembly 2206-068

Fuse Wire Assembly 2206-085

Glass Clip Support Assembly

Glass Latch Support Assembly

Pkg of 2 33858/2 Y

Qty 2 req

2146-413

Lava Rock 4021-296

Mineral Wool 050-721

Patch Kit, Firebrick PATCHKIT-FB

Remote RC300-QDF

Stainless Steel Liner 768-380A

Touch up Paint TUP-GBK-12

Wire Assembly, Module Reset 2201-030

Touch up Paint, Fiber STRATFORD-KIT

EMC Filter 2201-198

Stocked at Depot

Conversion Kit NG NGK-I30FB-C

Conversion Kit LP LPK-I30FB-C

Pilot Oriﬁ ce NG 593-528

Pilot Oriﬁ ce LP 593-527

Regulator NG NGK-DXV-50

Regulator LP LPK-DXV-50

Conversion Kit NG NGK-I35FB-C

Conversion Kit LP LPK-I35FB-C

Pilot Oriﬁ ce NG 593-528

Pilot Oriﬁ ce LP 593-527

Regulator NG NGK-DXV-50

Regulator LP LPK-DXV-50

QFI30FB-C Conversion Kits

QFI35FB-C Conversion Kits

49Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15

Page 50

D. Contact Information

Quadra-Fire, a brand of Hearth & Home Technologies

7571 215th Street West, Lakeville, MN 55044

www.quadraﬁ re.com

Please contact your Quadra-Fire dealer with any questions or concerns.

For the location of your nearest Quadra-Fire dealer,

please visit www.quadraﬁ re.com.

- NOTES -

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5601073, 5613487, 5647340, 5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending.

Quadra-Fire • QFI30FB-C, QFI35FB-C • 2221-901 Rev. S • 2/15 50

2000-945B