Page 1
R
Firescreen, Firescreen Leaf, Tuscan Bar and Tudor Panel Doors
Models: QFI30FB, QFI35FB
- Installation Instructions -
3. Mound the surround to the surround brackets with four
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
fl ammable materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
• Do NOT operate with protective barriers open or removed.
• The doors must remain closed if children will be present
during the operation of the fi replace.
screws. See Figure 1.
4. Attach the surround vanity panel with four 10-24 x 3/4
Phillips pan head screws. See Figure 2.
5. Once the surround is attached, slide the appliance
backward until the surround is tight to the existing noncombustible fi nished wall.
• The doors may be made operable per these instructions.
This may be done only upon request of a person responsible
for the use and operation of the fi replace.
• The doors can be returned to the locked position following
these instructions.
• These instructions are to be left with a person responsible
for the use and operation of the fi replace.
INTRODUCTION
The surround is used to fi ll the space between the insert
and the solid fuel fi rebox opening. The front is placed onto
the surround after it is attached to the insert.
WARNING! Risk of Fire! Combustible materials MUST
NOT overlap or be placed under a surround.
Combustible Materials Specifi cation
Materials made of or surfaced with wood, compressed
paper, plant fi bers, plastics, or other material that can ig-
nite and burn, whether fl ame proofed or not, or plastered
or unplastered shall be considered combustible materials.
CAUTION! Do not install damaged components.
SURROUND INSTALLATION
1. The surround is shipped with the brackets attached for
shipping purposes. Remove the surround brackets from
the surround by removing two screws on each bracket.
2. Mount the left and right surround brackets onto the
appliance with four screws. See Figure 1.
Quadra-Fire • Insert Door Installation Instructions • 2235-912 Rev. D • 5/11
Figure 1
Figure 2
1
Page 2
Figure 3
HANGING THE DOOR
1. An extension bracket will need to be installed on the
appliance for proper unit operation. See Figure 3.
2. All fronts mount on the hinges provided with the
surround.
For Inoperable Doors:
1. Full width fronts installed in the operable condition pivot
open on the left hinges to access the fi rebox. If the
child safety mechanism is engaged it will need to be
temporarily removed with a Phillips screwdriver. See
Figure 5.
2. Place the full width fronts onto the hinges by sliding the
door down onto the hinge pins on the surround.
3. The magnet catch and child safety lock will secure the
door on the right side.
For Operable Doors:
1. The operable doors will use the hinges on both sides
of the surround.
2. Place the left and right doors onto the corresponding
hinges by sliding the doors down onto the surrounds
hinge pins.
NOTE: The right door has two magnet catches and should
close last as it is designed to keep the left door closed.
TUDOR PANEL
1. The doors are shipped with a child safety lock. To lock
the doors, a Phillips screw driver and a 3/8 in. wrench
will be needed. After hanging the doors on the surround,
place the bolt through the back of the doors. The bolt
goes through both doors in the middle at the top, and is
retained by a nut to prevent them from operating. See
Figure 4.
Figure 4
2. If the bolt and nut used as a child safety lock are
removed, store them in the extension bracket for future
use. See Figure 3.
FIRESCREEN, FIRESCREEN LEAF AND TUSCAN BAR
1. The doors are shipped with a child safety lock.
2. After hanging the door on the surround, place the child
safety assembly with the provided fastener through the
hole in the lower right corner of the door.
3. Shut the door and line up the safety assembly over the
hinge pin.
4. Tighten the fastener with a Phillips screwdriver. See
Figure 5.
5. If the child safety lock assembly is removed, store it in
the extension bracket for future use. See Figure 3.
INSTALLATION OF CHILD SAFETY LOCK
CAUTION! Glass is hot during operation and cool
down. These doors are supplied from the factory with
parts to lock them shut for child safety.
• T o avoid burns or clothing ignition the doors must remain
closed if children will be present during the operation and
cool down of the fi replace.
• These doors may be assembled in locked or operable
condition. They must only be made operable upon
request of a person responsible for the use and operation
of the fi replace. They may be returned to the locked
position following these instructions.
• These instructions are to be left with a person responsible
for the use and operation of the fi replace.
Quadra-Fire • Insert Door Installation Instructions • 2235-912 Rev. D • 5/112
CHILD SAFETY LOCK
Figure 5
Page 3
Service Part List
TP-QFI30FB-BK, -SB / TPA-QFI30FB-BK, -SB
TP-QFI35FB-BK, -SB / TPA-QFI35FB-BK, -SB
SURROUNDS DESCRIPTION PART NUMBER
FBI30-4027-BK, -SB
VANITY PANEL 2201-210FBI30-4230-BK, -SB
FBI304432-BK, -SB
FBI35-4229-BK, -SB
VANITY PANEL 2202-210FBI35-4432-BK, -SB
FBI35-4832-BK, -SB
DOORS DESCRIPTION
MESH ASSEMBLY, LEFT 2235-095
MESH ASSEMBLY, RIGHT 2235-096
EXTENSION BRACKET 2235-216
MESH ASSEMBLY, LEFT 2237-095
MESH ASSEMBLY, RIGHT 2237-096
EXTENSION BRACKET 2235-216
FS-QFI30FB-BK, -SB
FS-QFI35FB-BK, -SB
FSL-QFI30FB-BK, -SB
FSL-QFI35FB-BK, -SB
TB-QFI30FB-BK, -SB
TB-QFI35FB-BK, -SB
EXTENSION BRACKET 2235-216
EXTENSION BRACKET 2235-216
EXTENSION BRACKET 2235-216
EXTENSION BRACKET 2235-216
EXTENSION BRACKET 2235-216
EXTENSION BRACKET 2235-216
MESH 2235-012
MESH 2237-012
MESH 2235-281
MESH 2237-281
MESH 2235-224
MESH 2237-224
PART NUMBER
Cleaning Instructions for Doors
Use a microfi ber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to clean
the door immediately after installation to remove acids
deposited by the installer or technician. Spray the cleaner
onto the microfi ber cloth and carefully wipe the entire
surface. The door should be cleaned in this manner
annually by the homeowner to remove fi ngerprints or
other contaminants. Once oxidation of the paint pigment
has occurred, cleaning will not restore the original color.
Quadra-Fire • Insert Door Installation Instructions • 2235-912 Rev. D • 5/11
Quadra-Fire, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
www.quadrafi re.com
Please contact your Quadra-Fire dealer with any
questions or concerns.
For the location of your nearest Quadra-Fire dealer,
please visit www. quadrafi re.com.
3
Loading...