Pioneer VSX-LX51 User Manual

Operating Instructions – Advanced MCACC PC Display Application Software –

audio/video multi-channel receiver

About this manual

These are the Operating Instructions for an application which displays on your computer screen the listening room reverberation frequency characteristics and the MCACC parameters measured by the Advanced MCACC function of your VSX-LX51 or VSX-1018AH. It explains everything you need to know to use the application, from installation to troubleshooting. You will need to operate the receiver to use this application, so please refer also to the Operating Instructions supplied with the receiver.

About the Advanced MCACC Application

The functions of the Advanced MCACC application are used with the same purpose as the “Reverb View” functions of the receiver itself (see pages 45 and 47 of the Operating Instructions of the VSX-LX51 or VSX1018AH), namely to display the reverberation characteristics of the listening environment. Using a computer provides cleaner, more easily readable graphs. The application can also be used to display the measurement values stored in the receiver’s MCACC memory.

Requirements for using the application on your PC

• Operating system must be Microsoft

• CPU must be at least Pentium 3 / 300 MHz or AMD K6 / 300 MHz (or equivalent) with at least 128 MB of memory, and your monitor must be able to display a minimum resolution of 800x600.

• An RS-232C port connector is necessary for graphical output. Refer to the PC’s operating instructions and/or the PC manufacturer for more information on making the proper port settings.

Microsoft, Windows XP and Windows 2000 are registered trademarks or trademarks of the Microsoft Corporation of the United States and other countries.

Windows® XP (Service Pack 2) or Windows® 2000.

Main features of the application

1. Displays 3D graphs of the reverberation frequency characteristics of your room. You can choose to

see these measurements both with and without the equalization performed by this receiver (before and after calibration).

2. Allows you to display a list of the Advanced MCACC parameters (the results of measurements).

3. Allows you to view graphs in a number of different formats.

4. Allows you to save the various measured data on the computer.

5. Allows you to make memos about the conditions in your room when you made the measurements,

etc.

6. Allows you to print the various graphs and the MCACC measurement values.

Continue

About the Advanced MCACC Application (Continued)

Things you can accomplish with this application

1. Advanced EQ Setup, which you can do with the receiver (see page 45 of the receiver’s Operating

Instructions), allows you to choose the optimum time period for auto EQ setup. You can use this application’s reverberation characteristics (Reverb) as a guide in choosing the best time period for your room. For details, see

2. Skewed reverb frequency characteristics in your listening room can prevent you from enjoying an

accurate sound field. The graphs displayed by this application are a powerful tool because they allow you to check these reverb frequency characteristics at a glance. You can also check the effectiveness of steps that you take to improve the acoustics of your listening room, for example, installing sound absorbent material. For details, see

3. The MCACC parameter display (Parameters) allows you to display on the computer all the

parameters (measurement values) stored in the receiver’s MCACC memories. For details, see

How to Interpret the Graphs

Display of the MCACC parameters

(page 18).

(page 25).

Installing the Application

Install this application on your PC by using the downloaded installer. You will find the installer in the folder that you specified when you downloaded the application. If a previous version of the Advanced MCACC application (“Ver. 1.1”, “Ver. 1.4” or “Ver. 2.0”) is installed on your computer, please update the application. For details, see

Updating the application

1 Double click the “PioneerAdvancedMCACC_e_ver_*_*.exe” file .

The number after “ver” in the filename is the version number of the installer. Depending on the current configuration of your PC, the InstallShield Wizard can take some time to appear.

2 Click “Next”.

(page 26).

3 (If you agree to the contents of the License Agreement), select “I accept the

terms in the license agreement”, then select “Next”.

The destination selection screen of the installer appears.

Troubleshooting

If an error occurs when you double click and you are unable to proceed with the installation.

Continue

Installing the Application (Continued)

4 Input the Customer Information, then select “Next”.

5 Click “Next”.

The application is installed in the folder indicated at “Destination Folder”. The destination folder can be changed by clicking “Change...”.

Continue

Installing the Application (Continued)

6 Choose “Install”.

A shortcut icon is created on the desktop.

7 Click “Finish”.

The installation is complete.

Operations on the Receiver and Cable Connections

Connect the receiver and the computer in order to display on the computer the various data measured on the receiver itself.

1 Connect the receiver to your PC with a RS-232C cable.

Caution

Before making or changing connections, switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system.

RS-232C RS-232C

Female-female

cross cable

STANDBY/ON

INPUT

SELECTOR

DIGITAL PRECISION

DIGITAL VIDEO

ADVANCED

PHASE

PROCESSING

SCALER

MCACC

CONTROL

DVD BD TV SAT DVR 1/DVR 2 VIDEO HDMI 1/HDMI 2 CD CD-R iPod USB MULTI CH IN

AUTO SURR/

HOME

STREAM DIRECT

THX

PHONES

MULTI-ZONE

FM/AM

STANDARD

ADVANCED

STEREO/

SURROUND

A.L.C.

VIDEO INPUT

DIGITAL INAUDIO RLVIDEO

ST –SPEAKERSON/OFFCONTROL

HDMI

MASTER VOLUME

MCACC

iPod DIRECT

SETUP MIC

USB

VSX-LX51/

VSX-1018AH

Note

• When using a notebook computer or other computer without an RS-232C terminal, this application can be used by connecting the receiver via USB using a commercially available USB-RS-232C conversion cable (USB-Serial cable). When using USB connections, be sure to select the proper COM port number for data transmission (see page 9

• The type of cable to use is a female-female cross cable. Different manufacturers use different names to refer to this type of cable. Sometimes it is called an “interlink” cable, and sometimes it is called a “reverse” cable.

Pin-out diagram of RS-232C cable to connect receiver and PC

Dsub 9-pin female

Continue

Operations on the Receiver and Cable Connections (Continued)

2 Perform the “Auto MCACC (ALL)” operation on the receiver. (See page 9 of the

receiver’s Operating Instructions.)

The setting here is not required if the “Auto MCACC (ALL)” operation has already been performed before connecting the RS-232C cable. Proceed to step 3.

3 From the receiver’s “Manual MCACC” menu, select “EQ Professional”, then select

“Reverb Measurement” to measure the room’s reverb characteristics. (See page 45 of the receiver’s Operating Instructions.)

If you want to measure the room’s reverb characteristics, select “EQ OFF”, then select “START”.

3e.EQ Professional MCACC : M1.MEMORY 1 Reverb Measure with

EQ OFF

[ START ]

:Cancel

If you want to measure the room’s reverb characteristics after equalization, first perform the “Auto MCACC (ALL)” operation, then select “EQ ON”, then “START”. (See page 23.)

Note

Measure the room’s reverb characteristics after equalization with the microphone at the same position as when the “Auto MCACC (ALL)” operation was performed. The measurements are performed with the EQ values stored in the MCACC memory selected on the receiver, so before measuring the reverb characteristics, select the MCACC memory to be measured after equalization.

3e.EQ Professional MCACC : M1.MEMORY 1 Reverb Measure with

EQ ON

[ START ]

:Cancel

4 Select “Output PC” from “Data Management”.

The message “Start the MCACC application on your PC” appears and the receiver enters transmission standby mode. It is ready to send data to your PC.

4.Data Management a . MCACC Data Check

b . Memory Rename c . MCACC Memory Copy d . MCACC Memory Clear

e . Output PC

:Return

This completes the preparations for sending the measurement data to your PC. (To send the data, proceed to the next section Application Operations.)

4e.Output PC

Start the MCACC application on your PC

:Cancel

Applications Operations

This section explains operations that you do in the application, from receiving measurement data to displaying graphs and saving the data.

Receiving measurement data

1 Double click the application shortcut icon on the PC desktop.

You can also start the application by selecting “Program”  “Pioneer Corporation”  “Advanced MCACC” from the “Start” menu. The application starts.

2 Select “Receive” under “File” on the menu bar.

3 Select the number of the COM port to which the RS-232C cable is connected.

If you do not know which COM port number to select, try selecting each port in turn, beginning with “COM1”.

COM port selection box

Note

Refer the operating instructions of your PC for more information about COM port settings.

Troubleshooting

If an error occurs when you select “Receive” and no data is sent.

Continue

Application Operations (Continued)

4 Select the type of data to be received, then select “OK”.

Select “Reverb” to receive the data for the room’s reverb characteristics, and “MCACC Parameters” to receive the data for the various MCACC parameters (measurements results). The “Group Delay” function is not used on this receiver. Nothing happens if it is selected.

Type of data

Data transmission starts.

When reception finishes the received data appear.

Note

• The data used to display the reverberation characteristics graph (Reverb) is deleted when the receiver is turned off. In this case, no reverberation characteristics graph is displayed even if data is received. If you have turned the power off after taking the measurements, take the measurements over again.

• The data used to display the MCACC parameters is not deleted even when the receiver’s power is turned off.

• In order to avoid malfunction, after the completion of the data transmission, unplug the RS-232C cable connecting your PC and the receiver.

Continue

Application Operations (Continued)

Graph and parameter displays (names and functions of parts)

When measurement data is received, the graphs and parameters display window appears. The display window is divided into two items, “Reverb” and “MCACC Parameters”. Select the desired tab to switch to that window and display the respective details. The “Group Delay” function is not used on this receiver. Nothing is displayed if “Group Delay” tab is selected. Also, on the Reverb graph display, Surround L and Surround R (SL and SR) are displayed as “Surround L A” and “Surround R A” (“SL A” and “SR A”).

Reverb (graph of the room’s reverberation frequency characteristics)

You can switch the display between individual displays for the different channels/frequencies or a list display of all the channels/frequencies (ALL). Below we explain the different parts of the individual displays and the ALL display, using the channel display as an example.

Individual display (Example: Left channel)

6 7 8

ALL display

Continue

Application Operations (Continued)

MCACC Parameters (list display of MCACC parameters)

A list of the measurements in all the MCACC memories is displayed. It is also possible to display the measurements in the individual MCACC memories.

Continue

+ 25 hidden pages