Pioneer DEH-P5900IB User Manual

0 (0)

Installation ENGLISH

Note:

• Check all connections and systems before final installation.

• Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions.

• Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle.

• Do not install this unit where: — it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result

of a sudden stop.

• The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet.

• Optimum performance is obtained when the unit is installed at an angle of less than 60°.

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following installation methods.

DIN Front-mount

Installation with the rubber bush

1. Insert the mounting sleeve into the dashboard.

• When installing in a shallow space, use a supplied mounting sleeve. If there is enough space behind the unit, use factory supplied mounting sleeve.

2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.

3. Install the unit as illustrated.

Removing the Unit

1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

2. Insert the supplied extraction keys into both sides of the unit until they click into place.

3. Pull the unit out of the dashboard.

182182

Trim ring

Dashboard

Mounting sleeve

Rubber bush

Screw

DIN Rear-mount

• It becomes easy to remove the trim ring if the

front panel is released.

2. Determine the appropriate position where the holes on the bracket and the side of the unit match.

3. Tighten two screws on each side.

• Use either truss screws (5 mm

× 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket.

Fastening the front panel

If you do not plan to detach the front panel, the front panel can be fastened with supplied screws and holders.

1. Attach the holders to both sides of the front panel.

2. Replace the front panel to the unit.

3. Flip the holders into upright positions.

4. Fix the front panel to the unit using screws.

Trim ring

Screw

Dashboard or Console

Factory radio mounting bracket

Screw

Holder

Note:

• When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result.

• Use this unit in other than the following conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.

— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a battery.

— Cover any disconnected cable connectors with

insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable directly

to ground. — Never band together multiple speaker’s nega-

tive cables.

• Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

• Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result.

• IP-BUS connectors are color-coded. Be sure to connect connectors of the same color.

• Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached.

• Cord function may differ according to the product, even if cord color is the same. When connecting this system, be sure to check all manuals and connect cords correctly.

No ACC positionACC position

DEH-P5900IB

Printed in Thailand Imprimé en Thaïlande

<XRD7143-A/N> UC

Connecting the Units ENGLISH

This product conforms to CEMA cord colors. Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

INSTALLATION MANUAL

MANUEL D’INSTALLATION

60°

put

Connecting the Units ENGLISH

7 When not connecting a rear speaker lead to a

Subwoofer

7 When using a Subwoofer without using the

optional amplifier

Interface cable (e.g., CD-I200)

iPod with Dock Connector

Dock connector

Dock connector port

2 m (6 ft. 7 in.)

This product

Rear output

Front output

Antenna jack

Subwoofer output

Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections.

Yellow Connect to the constant 12 V supply terminal.

Red Connect to terminal controlled by ignition switch (12 V DC).

Orange/white Connect to lighting switch terminal.

Black (chassis ground) Connect to a clean, paint-free metal location.

(sold separately)

Fuse (10 A)

Gray

15 cm (57/8 in.)

IP-BUS input

(Blue)

IP-BUS cable

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

Power amp

(sold separately) AUX jack (3.5 ø) Use a stereo mini plug cable

to connect with auxiliary equipment

Wired remote in

ard-wired remote control

Connect with RCA cables (sold separately)

Power amp (sold separately)

adaptor can be connected (sold separately)

Multi-CD player (sold separately)

System remote control

Front speaker Front speaker

≠≠

White Gray

Front speaker Front speaker

Left Right

≠

Gray/blackWhite/black

≠

Green Violet

Rear speaker Rear speaker

≠

Green/black Violet/black

≠

Power amp (sold separately)

iPod with Dock Connector

Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections.

Yellow Connect to the constant 12 V supply terminal.

Red Connect to terminal controlled by ignition switch (12 V DC).

Orange/white Connect to lighting switch terminal.

Black (chassis ground) Connect to a clean, paint-free metal location.

Dock connector

Dock connector port

2 m (6 ft. 7 in.)

This product

Subwoofer output

Front output

Antenna jack

Subwoofer output

Interface cable (e.g., CD-I200) (sold separately)

Gray

Fuse (10 A)

15 cm (57/8 in.)

AUX jack (3.5 ø) Use a stereo mini plug cable

to connect with auxiliary equipment.

Wired remote input

Hard-wired remote control IP-BUS input (Blue)

adaptor can be connected (sold

separately).

Multi-CD player

IP-BUS cable

(sold separately)

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

White Gray

Front speaker Front speaker

Left Right

≠

Gray/blackWhite/black

≠

Green Violet

Subwoofer (4 Ω) Subwoofer (4 Ω)

≠

Green/black Violet/black

≠

When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything with Green and Green/black leads.

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

Perform these connections when using the optional amplifier.

Rear speaker

Subwoofer

≠≠

Rear speaker

Subwoofer

Note:

Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural.

Not used.

Green Violet

Green/black Violet/black

Subwoofer (4 Ω) × 2

≠

+ 2 hidden pages