Philips GC4939/00 User Manual
1 2
1-9
1-1
1-8
1-7
~2 min.
3-6
3-5
~2 min.
2-32-2
2-5
3
3-2 3-4
3-9
3-11 3-12
3-7
3-10
3-8
1-6
1-10
1-5
1-2
1-3
3-32-4
2-72-6
2-9
2-8
~30 sec.
2-1
~30 sec.
3-1
4
4-1
4-2
4-3
4-4
3
1-4
2-11
2-10
GC4930 series
ENGLISH 7
РУССКИЙ 11
TÜRKÇE 15
ҚАЗАҚ 19
1 2 3 4 5
6
7
8
9
© 2017 Koninklijke Philips N.V.
All rights reserved.
4239 001 08164
User manual
Руководство пользователя
Kullanım kılavuzu
Пайдаланушы нұсқаулығы
GC4930 series
10
EN To use RU Использование TR Kullanım KK Пайдалану
1 2
1-1
1-5
1-9
1-2
1-6
1-10
1-3
1-7
~2 min.
1-4
1-8
EN Quick Calc Release (Specic types only) RU Быстрая очистка от накипи
(См. “Сводная таблица параметров моделей”) TR Hızlı Kireç Çözme (sadece belirli
modellerde) KK Жылдам қақтан босату (Жиынтық кесте параметрлерінің модельдер)
2-1
2-5
2-9
~30 sec.
2-10
2-32-2
2-72-6
2-11
2-8
3
EN Calc-Clean (Specic types only) RU Calc-Clean (См. “Сводная таблица
параметров моделей”) TR Calc-Clean (sadece belirli modellerde)
KK Қақтан тазалау (Жиынтық кесте параметрлерінің модельдер)
3-1
3-5
~2 min.
3-9
3-2 3-4
~30 sec.
3-6
3-10
3-32-4
3-7
3-11 3-12
3-8
RU
Паровой утюг
Изготовитель: “Филипс Консьюмер Лайфстайл Б.В.”, Туссендиепен 4, 9206
АД, Драхтен, Нидерланды
Импортер на территорию России и Таможенного Союза: ООО “ФИЛИПС”,
Российская Федерация, 123022 г. Москва, ул. Сергея Макеева, д.13,
тел. +7 495 961-1111.
Для бытовых нужд
Класс защиты от поражения электрическим током: Класс I
Сделано в Индонезии
Сводная таблица параметров моделей:
Модель Электрические параметры Быстрая
GC4930 220-240 В, 50-60 Гц, 2000-2400 Вт нет да
GC4939 220-240 В, 50-60 Гц, 2500-3000 Вт да нет
Условия хранения, эксплуатации
Температура +0 °C - +35 °C
Относительная влажность 20% - 95%
Атмосферное давление 85 - 109 kPa
очистка от
накипи
Calc-Clean
Кнопка
KK
Бу үтігі
Өндіруші: “Филипс Консьюмер Лайфстайл Б.В.”, Туссендиепен 4, 9206 АД, Драхтен,
Нидерланды.
Ресей және Кедендік Одақ территориясына импорттаушы: ФИЛИПС ЖШҚ, Ресей
4
EN To store RU Хранение TR Saklama KK Сақтау
4-1
4-2
4-3
4-4
3
Федерациясы, 123022 Мәскеу қаласы, Сергей Макеев көшесі, 13-үй, тел. +7 495 961-1111.
Тұрмыстық қажеттіліктерге арналған
Электр тогымен зақымданудан қорғау класы: Класс I
Индонезияда жасалған
Жиынтық кесте параметрлерінің модельдер:
Модель Электр параметрлері Жылдам
қақтан
босату
GC4930 220-240 В, 50-60 Гц, 2000-2400 Вт жоқ иә
GC4939 220-240 В, 50-60 Гц, 2500-3000 Вт иә жоқ
Сақтау шарттары, пайдалану
Температура +0 °C - +35 °C
Салыстырмалы ылғалдылық 20% - 95%
Атмосфералық қысым 85 - 109 kPa
Қақ тазалау
түймесі
7
ENGLISH
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the
support that Philips oers, register your product at www.philips.com/welcome.
Read this user manual and the important information leaet carefully before you use the
appliance. Save them for future reference.
Product overview
1 Water tank lid
2 Steam slider
Steam on
Steam o
3 Steam boost button
4 ‘Iron ready’ light
5 Calc-Clean / Quick Calc Release reminder light
6 Mains cord
7 Cord winding
8 Calc-Clean button (specic types only)
9 Soleplate
10 Quick Calc Release (specic types only)
Exclusive technology from Philips
OptimalTEMP technology
The OptimalTEMP technology enables you to iron all types of ironable fabrics, in any
order, without adjusting the iron temperature and without sorting your garments.
It is safe to just rest the hot soleplate directly on the ironing board without putting back to
the iron platform. This will help reduce the stress on your wrist.
This iron has been approved by The Woolmark Company Pty Ltd for the ironing of woolonly products, provided that the garments are ironed according to the instructions on the
garment label and those issued by the manufacturer of this iron. R0000. The Woolmark
symbol is a certication mark in many countries.
Using the appliance
Note: The iron may give o some smoke when you use it for the rst time. This stops
after a short while.
Type of water to use
This appliance has been designed to be used with tap water. However, if you live in an
area with hard water, fast scale build-up may occur. Therefore, it is recommended to use
distilled or demineralized water to prolong the lifetime of the appliance.
Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling
agents, ironing aids, chemically descaled water or other chemicals, as they may cause
water spitting, brown staining or damage to your appliance.
ENGLISH
8
Ironable fabrics
1 Check whether the garment is ironable by reading the label on the garment (Fig. 1-5).
Do not iron non-ironable fabrics. Prints on the garment are not ironable either.
Iron with extra steam
Press and hold the steam boost trigger to get more steam to remove stubborn creases.
Auto shut-o
The auto shut-o function automatically switches o the appliance if it has not been
used for 2 minutes resting on its soleplate or 8 minutes resting on its backplate.
The ‘iron ready’ light ashes to indicate the appliance is at auto-o status.
To let the appliance heat up again, pick up the appliance or move it slightly. The ‘iron
ready’ light turns to breathing and the appliance starts to heat up.
Cleaning and maintenance
For more information on how to performance clean and maintenance on the iron, refer to
the videos in this link: http://www.philips.com/descaling-iron.
Cleaning the soleplate
1 Unplug the appliance and let it cool down.
2 Pour any remaining water out of the water tank.
3 Wipe akes and any other deposit o the soleplate with a damp cloth and a
non-abrasive (liquid) cleaning agent.
Note: To keep the soleplate smooth, avoid hard contact with metal objects. Never use a
scouring pad, vinegar or other chemicals to clean the soleplate.
Quick Calc Release (specic types only)
IMPORTANT: The Quick Calc Release automatically collects loose scale particles during
ironing. After 1 to 3 months of use, the Calc-Clean reminder light starts ashing to
remind you to use the Quick Calc Release function (Fig. 2-1). This is to remove scales
collected from your iron to prolong its life. When the Calc-Clean reminder light is
ashing, the iron does not heat up.
Tip: The Quick Calc Release function can be used at any time, even when the reminder
light is not activated yet. If you live in a hard water area, use the function more frequently.
Do not perform the Quick Calc Release when the iron is hot. Do not pour water into the
Quick Calc Release opening.
1 Unplug the appliance (Fig. 2-2) and make sure that the appliance is cool (Fig. 2-3).
2 Hold the appliance in vertical position over the sink.
3 Flip up the lever of Quick Calc Release collector (Fig.2-4) and pull out the collector
(Fig.2-5).
4 Clean the Quick Calc Release collector with water (Fig. 2-6, Fig. 2-7).
ENGLISH
9
5 Gently shake the appliance to allow scale particles to fall out (Fig. 2-8).
6 Insert the Quick Calc Release collector back into the appliance (Fig. 2-10).
7 Push down the lever (“click”) to lock the collector (Fig. 2-11).
Calc-Clean (specic types only)
IMPORTANT: After 1 to 3 months of use, the Calc-Clean reminder light starts ashing to
remind you to use the Calc-Clean function (Fig. 3-1). This is to remove scales in your iron
to prolong its life.
Tip: The Calc-Clean function can be used at any time, even when the reminder light is
not activated yet. If you live in a hard water area, use the function more frequently.
1 Make sure that the steam slider is set to “steam o” position (Fig. 3-2).
2 Make sure there is enough water (more than 3/4) in the water tank. If there is not
enough water, unplug the iron, ll the water to MAX indication (Fig.3-3) and plug in
the iron again (Fig.3-4).
Do not pour vinegar or other descaling agents into the water tank.
3 Wait for the iron to heat up. This takes about 2 minutes (Fig.3-5).
Note: the Calc-Clean reminder light turns o during heating up. .
4 Unplug the iron when the ‘iron ready’ light stops breathing (Fig. 3-7).
5 Hold the iron over the sink. Keep pushing the Calc-Clean button and gently shake
the iron forth and back until all water in the water tank has been used up (Fig. 3-8).
Scales is ushed out, steam and boiling water also come out of the soleplate.
Note: Repeat steps 2 to 5 if the water that comes out of the appliance still contains
scale particles.
6 Plug in the appliance and let the appliance heat up to dry the soleplate. This takes
about 2 minutes (Fig. 3-9).
7 Unplug the appliance (Fig. 3-10). Move the appliance gently over a piece of cloth to
remove any water stains on the soleplate (Fig. 3-11).
Troubleshooting
This chapter summarises the most common problems you could encounter with
the appliance. If you are unable to solve the problem with the information below,
visit www.philips.com/support for a list of frequently asked questions or contact
the Consumer Care Centre in your country.
Problem Possible cause Solution
The iron cannot
remove wrinkles from
the garment.
The iron does not
produce any steam.
There is no steam during
ironing.
There is not enough water in
the tank.
The steam slider is set to . Set the steam slider to .
Fill the water tank and set the steam
slider to .
Fill the water tank.
ENGLISH
10
Problem Possible cause Solution
The ironing board cover
becomes wet or there
are water droplets on
the garment during
ironing.
Water droplets drips
onto the garment
during ironing.
The iron does not
produce a steam boost.
Dirty water and
impurities come out of
the soleplate during
ironing.
Water drips from the
soleplate after the iron
has been unplugged.
There is an amber light
ashing on the handle
of the iron.
The iron leaves a shine
or an imprint on the
garment.
The iron is not hot enough yet
to product steam.
The ironing board cover
becomes wet or there
are water droplets on the
garment during ironing.
You have an ironing board
cover that is not designed to
cope with the high steam rate
of the appliance.
You have used the steam
boost function too often
within a short period.
You have not closed the water
tank lid properly.
You have not insert the Quick
Calc Release collector properly
back to the appliance (specic
types only).
You have used the steam
boost function too often
within a short period.
The iron is not hot enough for
ironing yet.
You have put a chemical into
the water tank.
Hard water with impurities or
chemicals has formed akes
inside the soleplate.
You have put the iron in
horizontal position with water
still left in the water tank.
The steam slider is set to . Set the steam slider to .
The Calc-Clean reminder light
is activated. This is to remind
you to perform calc clean.
The surface to be ironed was
uneven, for instance because
you ironed over a seam or a
fold in the garment.
Wait until the ‘iron ready’ light has
stopped breathing and lights up steadily.
Replace the ironing board cover if the
foam material has worn out. You can
also add an extra layer of felt material
under the ironing board cover to prevent
condensation on the ironing board. You
can buy felt in a fabric shop.
Put an extra layer of felt material under
the ironing board cover to prevent
condensation on the ironing board.
You can buy felt in a fabric shop.
Continue ironing in horizontal position
and wait a while before you use the
steam boost function again.
Press the lid until you hear a ‘click’.
Stop ironing and let the iron cools down
for at least 1 hour. Take out the Quick
Calc Release collector. Insert it back into
the appliance and ensure the collector is
in-line with the surface of the appliance.
Push down the lever (“click”).
If the Quick Calc Release collector is
damaged, contact a consumer care
center in your country (see the world wide
guarantee leaet for contact details).
Continue ironing in horizontal position
and wait a while before you use the
steam boost function again.
Wait until the ‘iron ready’ light has
stopped breathing and lights up steadily.
Rinse the water tank and do not put any
perfume or chemicals into the water tank.
Perform Quick Calc Release (specic types
only) or Calc-Clean (specic types only).
See chapter “Cleaning and maintenance”.
Empty the water tank after use, or store
the iron in vertical position.
Perform Quick Calc Release (specic types
only) or Calc-Clean (specic types only).
See chapter “Cleaning and maintenance”.
The iron is safe to use on all ironable
garments. The shine or imprint is not
permanent and disappears when you wash
the garment. Avoid ironing over seams or
folds. You can also place a cotton cloth over
the area to be ironed to avoid imprints.
Loading...