Pelco CM6700-VMC2-X User Manual

®

CM6700-VMC2

Expansion Card

Installation/Operation Manual

C524M (8/97)

1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be

observed.

1. Installation and servicing should only be done by Qualified Service Personnel
and conform to all Local codes.

2. Only use replacement parts recommended by Pelco.

3. After replacement/repair of this unit’s electrical components, conduct a resis­tance measurement between line and exposed parts to verify the exposed
parts have not been connected to line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates static sensitive components. Use antistatic
grounding equipment whenever handling or servicing modules and
components. When circuit modules are removed from the frame, place
them on a flat static-controlled surface. Failure to follow this precau­tion can result in component damage due to electrostatic discharge.

This symbol indicates that there are important operating and mainte­nance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com
In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] or FAX [phone]

manual prior to installation and operation.

2.0 DESCRIPTION The CM6700-VMC2 is a 2-monitor expansion card for the CM6700 Matrix System.

This simple, plug-and-play installation expands the CM6700 video outputs from
two (2) to four (4) monitors. When the system is powered again after installation,
the CM6700 will automatically recognize the expansion card.

Included in this package:

Qty Item Part Number

1 2-monitor expansion card CM6700-VMC2 (NTSC version)

CM6700-VMC2-X (PAL version)

5 1/4-inch hex standoff SPA8423

5 6-32 phillips head screw ZH6-32.250BPP

5 #6 nylon washer ZH150X310X32N

3.0 INSTALLATION To facilitate the installation the CM6700-VMC2 expansion board, removal of the

CM6700 Switcher/Controller Unit (SCU) from its installed location may be required.

CAUTION:

The CM6700­VMC2 is a static sensitive
device. Exercise caution
during handling and while
working around the exposed
electronics within the
CM6700.

WARNING:

Installation of
the CM6700-VMC2 should
only be done by qualified
service personnel and
should include the use of an
appropriate grounding
strap.

IMPORTANT:

The expansion card
must be carefully aligned to avoid
damage to the connector pins.

Inspect the expansion card prior to installation. It is very important that all of the
expansion card connector pins are straight before attempting to install the expan­sion card.

To install the CM6700-VMC2 do the following:

1. Disconnect the CM6700 power cord from the wall outlet.

2. Remove the top cover from the CM6700 SCU.

3. Remove and replace the five (5) motherboard mounting bolts with the five (5)
1/4-inch hex standoffs (supplied), and tighten. See Figure 1.

4. Determine the correct orientation of the expansion card to the motherboard.
The connector pins on the expansion card correspond to the 8 connectors
shown in Figure 1.

5. Seat the expansion card. This is a delicate process. The connector pins on the
expansion card must align exactly with the connectors on the motherboard.

a. Place the expansion card onto the standoffs.

b. Align the two (2) connector pins indicated in Figure 1 with their corre-

sponding connector openings.

c. Once the pins are aligned, gently push the expansion card onto the con-

nectors, a little at a time, until the expansion card is completely seated
onto the motherboard.

d. Be sure that the expansion board is fully seated.

8. Using the 6-32 screws and nylon washers (included), secure the expansion
card to the standoffs.

9. Replace the SCU cover and plug the power cord into the wall outlet.

The SCU will automatically recognize the expansion card upon power up of the
system.

2 Pelco Manual C524M (8/97)

6/32 SCREW (5)

WASHER (5)

CONNECTOR PIN

NYLON

1/4" HEX

STAND OFFS (5)

CONNECTORS (8)

CONNECTOR PIN

Figure 1. Exploded Assembly Diagram

2-MONITOR

EXPANSION BOARD

CM6700

MOTHERBOARD

Pelco Manual C524M (8/97) 3

4.0 WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure

CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five­year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

dome products.

• Two years on Spectra

continuous motion applications.

• Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications

(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone]
to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received
by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or [phone] to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number

and freight should be prepaid. Ship to the appropriate address below.

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1997, Pelco. All rights reserved.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2, CC3701H-2X,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

4 Pelco Manual C524M (8/97)