Pelco CC3551H-2, C1984M-F, CC3651H-2X User Manual

®

Installation/Operation

CC3551H-2 and CC3651H-2X
DSP Color Camera

C1984M-F (4/03)

Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com

USA & Canada: Tel: [phone] • Fax: [phone]

International: Tel: [phone] • Fax: [phone]

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9. Only use attachments/accessories specified by the manufacturer.

10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, the
apparatus does not operate normally, or the apparatus has been dropped.

12. Apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as
vases, shall be placed on the apparatus.

13. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

14. Caution: Danger of explosion if battery is replaced incorrectly. Replace only with the same or
equivalent type.

15. To reduce the risk of shock, do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.

16. Use only installation methods and materials capable of supporting four times the maximum specified
load.

17. Use only UL listed class 2 power supply.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous
voltage constituting a risk of electric shock
is present within this unit.

This symbol indicates that there are impor-

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

tant operating and maintenance instructions
in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

[

]

2

Pelco Manual C1984M-F (4/03)

REGULATORY NOTICES

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device many not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

DESCRIPTION

The CC3551H-2 and CC3651H-2X are high resolution, color video cameras with a 1/3-inch CCD imager.
The cameras feature digital slow shutter (DSS) mode, a direct drive/auto iris lens connector, adjustable
back focus, backlight compensation, automatic gain control, and an adjustable C/CS lens mount.

Models

CC3551H-2 High resolution, 480 TV lines, HyperHAD™ CCD, minimum illumination of 0.035 lux at

CC3651H-2X High resolution, 470 TV lines, EXviewHAD™ CCD, minimum illumination of 0.02 lux at

f1.2 and 50 IRE, NTSC format (CE, UL, cUL)

f1.2 and 50 IRE, PAL (CE, UL, cUL, UL AR-S)

Pelco Manual C1984M-F (4/03)

[

]

3

CAMERA LAYOUT

BACK FOCUS
ADJUSTMENT
LOCKING
SCREW

MOUNT ADAPTER

PHASE ADJUSTMENT

LEVEL ADJUSTMENT

POWER SUPPLY

COSMETIC TRIM
RING

Note: The cosmetic
trim ring conceals the

BACK FOCUS
ADJUSTMENT
RING

LED light for more
descreet surveillance
operations. The trim
ring also hides the

BNC VIDEO CONNECTOR

LENS CONNECTOR

LED

DIP SWITCHES

power connectors and
protects the DIP
switches.

Figure 1. Camera Layout

INSTALLATION

Lens Mounting

The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount
lens, but is easily adjusted for a C-mount lens.

1. C-Mount Lens Only - Rotate the back focus adjustment fully counterclockwise before install-

ing the C-mount lens (refer to the section on

Back Focus Adjustment

).

2. Remove the cosmetic trim ring from the back of the camera (refer to Figure 1). Set the lens mode

selector switch on the side of the camera to AIV (auto iris video drive lens) or AID (auto iris DC drive
lens). Refer to the

Switch Settings

section. Switch setting is determined by the type of lens used.

3. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the

lens and the CCD element. If necessary, use clean, compressed air to remove any foreign matter.

4. Thread the lens cable through the cosmetic trim ring.

5. Connect the auto iris lens to the four-pin connector located on the side of the camera. Pin connec-

tions for the iris drive connector are as follows:

PIN DC AUTO IRIS LENS VIDEO AUTO IRIS LENS

3 4

1 Control coil negative (-) Lens positive supply

2 Control coil positive (+) Not used

3Drive coil positive (+) Video drive signal

12

4Drive coil negative (-) Ground

Figure 2. Lens Connections

[

]

4

Pelco Manual C1984M-F (4/03)