C281M-C (10/99)
CM400
Corner Mount Adapter
3500 Pelco Way,
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
International Customers:
Tel +1 (559) 292-1981
FAX +1 (559) 348-1120
www.pelco.com
NOTE:
Fasteners to secure the
CM400 to a load-bearing solid
surface are not supplied.
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four times the maximum specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
5. To prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant around the bolt holes between the mount and mounting surface.
DESCRIPTION
The CM400 Corner Mount Adapter is designed for use with the LWM41 Legacy® Series Wall
Mount when mounting on the corner of a structure is required.
The CM400 is fabricated from aluminum and will support up to 75 lb (33.75 kg).
INSTALLATION
When mounting the CM400 to a wall, make certain that the mounting surface is capable of
supporting the full load of the mount, pan/tilt, enclosure, and camera.
1. Drill holes in the mounting surface using the CM400 mount as a template and attach the
mount securely with fasteners of a suitable size.
2. Attach and secure the LWM41 Wall Mount to the four 5/16-inch studs provided on the
CM400 with the supplied hardware.
NOTE:
Conduit knockouts are
supplied on the block-off plate,
offering greater flexibility in installation options.
3. Attach the pan/tilt and enclosure to the LWM41 Wall Mount according to the instructions
provided with the mount.
Block-Off Plate Installation
Included with the CM400 is a block-off plate. Depending on the particular installation requirements of the CM400 and LWM41 Wall Mount, the supplied block-off plate may be used as
follows:
The block-off plate or “gland” plate is designed to be used with the CM400 as a means to
close the 2.5-inch diameter hole in the mounting flange of the wall mount. If feedthrough wiring
from the mount through the CM400 is not needed, then the block-off plate may be installed
between the LWM41 and the CM400. This block-off plate installation will protect the internal
cavity of the wall mount. It is recommended that the block-off plate be used in outdoor applications.
SPECIFICATIONS
Adapter Mounting: Four 5/16-inch studs
Suggested
Mounting Method: Secure to solid mounting
Construction: Aluminum
Dimensions: See Figure 1
provided for mounting
LWM41 to CM400 (nuts
and split lock washers
supplied)
surface with eight fasteners of a suitable size
(suggested minimum
1/4-inch diameter, not
supplied)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL
OTHERS ARE INCHES
Figure 1. CM400 Dimension Drawing
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material
or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera
models, which have a five-year warranty.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.months on DX
Series digital video recorders, NVR300 Series network video recorders, Endura™ Series
distributed network-based video products, and TW3000 Series twisted pair transmission
products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or
accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting
from the specific use or application made of the Products. Pelco’s liability for any claim,
whether based on breach of contract, negligence, infringement of any rights of any party
or product liability, relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties)
however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also
have additional rights, which are subject to variation from state to state.
Finish: Gray polyester powder
coat
Maximum Load: 75 lb (33.75 kg)
Weight:
CM400 3 lb (1.36 kg)
(Design and specifications are subject to
change without notice.)
If a warranty repair is required, the Dealer must contact Pelco at (800)289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by which the item
was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory
at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods
to:
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date Comments
C281M-C 10/99 Revised to new format. Removed all references to SCM400 and ST4.
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.
™ Endura and ExSite are trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.