Pelco CM1750, TB1750, CM1750S User Manual

CA1750 Mount Adapter
Installation Instructions
C209M (4/98)

1.0 DESCRIPTION The CA1750 Mount Adapter is used when installing a bottom-mount camera on a

BS1750, CM1750, CM1750S, or TB1750 mount only when the mount is attached to
a ceiling. Use of the adapter , in this situation, will allow the camer a to be mounted in
its correct orientation, rather than being inverted.

2.0 INSTALLATION To install the adapter (refer to Figure 1):

®

CAUTION:

not to damage the cam­era by screwing the
adapter too far onto the
threaded stud. As soon as
the stud threads appear
through the adapter cap­tive nut, tighten the
knurled nut.

Be careful

1. Place the camera inside the adapter and align the camera mount boss with
the elongated hole in the adapter.

2. Attach the camera to the adapter with the provided 1/4-20 bolt and washers.

3. Attach the adapter with camera to the 1/4-20 threaded stud on the installed
mount swivel head. Tighten the knurled nut on the mount against the adapter.

Figure 1. CA1750 Mount Adapter

Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • Pelco Online @ http://www.pelco.com

In North America and Canada: Tel [phone] • FAX [phone] • DataFAX [phone]

International Customers: Tel [phone] or FAX [phone] • DataFAX (1-559) 292-0435

3.0 WARRANTY AND RETURN INFORMATION

3.0 WARRANTY AND
RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment. Excep­tions to this warranty are as noted below:

• Three years on Genex™ Series multiplexers.

• Two years on all standard motorized and fixed focal length lenses.

• Two years on Legacy®, Intercept®, PV1000 Series, CM6700/CM8500/CM9500/
CM9750/CM9760 Matrix, Spectra™, DF5 Series and DF8 Fixed Dome products.

• Two years on WW5700 series window wiper (excluding wiper blades).

• Two years on cameras.

• Six months on all pan and tilts, scanners or preset lenses used in continuous
motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warranty all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to
Pelco , Clo vis , California. Repairs made necessary by reason of misuse, alteration,
normal wear, or accident are not cov ered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss result­ing from the specific use or application made of the Products. P elco’ s liability for an y
claim, whether based on breach of contract, negligence, infringement of any rights
of any party or product liability, relating to the Products shall not exceed the price
paid by the Dealer to Pelco f or such Products. In no e vent will P elco be liable f or any
special, incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

®Pelco and the Pelco logo are registered

trademarks of Pelco.

©Copyright 1998, Pelco. All rights

reserved.

The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the
following information:

1. Model and serial number

2. Date of shipment, P.O . number , Sales Order n umber , or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under
the warranty conditions stated above, please include a written e xplanation with the
product when returned.

Ship freight prepaid to: Pelco

300 West Pontiac W a y
Clovis, CA 93612-5699

Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the
factory at [phone] or [phone] to obtain an authorization number (CA
number if returned for credit, and RA number if returned for repair). Goods returned
for repair or credit should be clearly identified with the assigned CA/RA number and
freight should be prepaid. All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.

Ship freight prepaid to: Pelco

300 West Pontiac W a y
Clovis, CA 93612-5699

2 Pelco Manual C209M (4/98)