Pelco CM1450 User Manual

C201M-D (3/00)
CM1450
Light-Duty Camera Mount

®

3500 Pelco Way,
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]

International Customers:
Tel [phone]
FAX [phone]

PelcoEurope BV
Dillenburg Center,
Dillenburgstraat 5F
5652 Eindhoven
The Netherlands
Tel [phone]
FAX [phone]

www.pelco.com

U

®

L

LISTED

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service and installation personnel.

2. Installation shall be done in accordance with all local and national electrical and mechani­cal codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maxi­mum specified load.

The product and/or manual may bear the following marks:

This symbol indicates that danger­ous voltage constituting a risk of
electric shock is present within
this unit.

This symbol indicates that there
are important operating and main­tenance instructions in the litera­ture accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

DESCRIPTION

The CM1450 is a light-duty camera mount capable of supporting cameras up to 7 pounds
(3.15 kg) when securely mounted. This mount is not recommended for use with enclosures.

NOTE:

Make certain that the
mounting surface is able to sup­port the combined weight of the
mount and the camera.

The mount is constructed from aluminum and is supplied with a swivel head for 360-degree
pan adjustment and 90-degree tilt adjustment.

INSTALLATION

To install the CM1450 mount, perform the following steps.

1. Drill holes in the mounting surface using the mount as a template. Attach the mount se­curely with three 1/4-inch diameter fasteners or one 5/16-inch diameter and one 1/4-inch
diameter fastener if mounting to a wall stud. Fasteners are not supplied.

2. Attach the camera to the 1/4-20 threaded stud on the swivel head and tighten the nut
against the camera.

3. Loosen the set screw on the swivel assembly, if necessary, with the Allen wrench that is
provided. Position the camera in the desired position and tighten the set screw.

SPECIFICATIONS

MECHANICAL

Pan Adjustment: 360°
Tilt Adjustment: 90°
Locking Method: Set screw secures swivel assembly

2.68

(6.80)

1.50

(3.81)

1.40

(3.56

2.84

(7.21)

5.49

(13.73

3.48

(8.84)

9.72

(24.69)

1/4-20 X .25 (.635)

10.71

(27.20)

3.55

(9.02

GENERAL

Suggested
Mounting: Secure with three 1/4-inch

diameter fasteners to a solid
surface or one 5/16-inch
diameter and one 1/4-inch
diameter fastener where
wall studs are encountered.
(Fasteners not supplied.)

Camera
Mounting: 1/4-20 threaded stud and nut

Maximum
Load: 7 lb (3.15 kg)

Construction: Aluminum
Finish: Gray polyester powder coat

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;
ALL OTHERS ARE INCHES.

Figure 1. CM1450 Dimension Drawing

WARRANTY AND RETURN INFORMATION

WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material
or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X camera
models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.

• Two years on Spectra®, Esprit®, ExSite™, and PS20 Scanners, including when used in
continuous motion applications.

• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.months on DX
Series digital video recorders, NVR300 Series network video recorders, Endura™ Series
distributed network-based video products, and TW3000 Series twisted pair transmission
products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or
accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting
from the specific use or application made of the Products. Pelco’s liability for any claim,
whether based on breach of contract, negligence, infringement of any rights of any party
or product liability, relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties)
however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also
have additional rights, which are subject to variation from state to state.

Dimensions: See Figure 1
Weight: 1.2 lb (0.5 kg)

If a warranty repair is required, the Dealer must contact Pelco at [phone] or (559)
292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by which the item
was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory
at [phone] or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods
to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

REVISION HISTORY

Manual # Date Comments

C201M-C 4/99 Revised installation instructions for mounting to a wall stud. Revised to new format.
C201M-D 3/00 Revised Figure 1 per ECO# 00-5643.

® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.
™ Endura and ExSite are trademarks of Pelco. © Copyright 2000, Pelco. All rights reserved.