Pelco CLCLD5HD, CLCLD5HDPG-1, LD5HDPG-1 User Manual

C2435M-A (2/03) CLCLD5HD Series

Lower Dome for Heavy-Duty Spectra

Systems

3500 Pelco Way Clovis, CA 93612-5699 USA

In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150

International Customers: Tel +1(559) 292-1981 FAX +1(559) 348-1120

www.pelco.com

DESCRIPTION

The following are lower domes for the Heavy-Duty Spectra and feature tamper-resistant hardware and an aluminum trim ring.

Models

CLCLD5HDF-1 Standard clear dome for the CC5BCBW-HF1 Heavy-Duty Spectra system CLCLD5HDBF-1 Heavy-Duty clear dome for the CC5BCBW-HBF1 Heavy-Duty Spectra system CLCLD5HDPG-1 Standard clear dome for the CC5BCBW-HP Heavy-Duty Spectra system LD5HDPG-1 Heavy-Duty clear dome for the CC5BCBW-HBF1 Heavy-Duty Spectra system

INSTALLATION

Pendant Models

Refer to Figure 1.

1. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in the groove on the trim ring of the lower dome.

2. Attach the back box trim leash to a retainer screw inside the lower dome.

3. Environmental Models Only – Plug the two-pin heater connection in the lower dome into the mating connector in the back box.

4. Align barrel locks in lower dome with the holes located on each side of the back box. Push the lower dome onto the back box. Press the center pins of the barrel locks in to secure the lower dome.

TRIM LEASH

Figure 1. Lower Dome Installation,

Pendant Models

00994

O-RING

BARREL LOCK

In-Ceiling Models

Refer to Figure 2.

1. Attach the back box trim leash to one of the 8-32 x .275-inch screws that secure the back box to the mounting ring.

2. Align ball studs (located on the mount ring) with the ball stud receivers (located on the inside of the lower dome).

3. Place the lower dome over the back box.

4. Push the lower dome over the back box, line up the mounting screw holes. Use the tamper-resistant screws and the tool bit supplied with the ceiling panel (CLCD5-P), and attach the lower dome to the back box.

Figure 2. Lower Dome Installation,

In-Ceiling Models

MAINTENANCE

Clean the acrylic dome as needed. Be careful not to scratch the surface of the dome. Use a nonabrasive cleaning cloth and agent that is safe for acrylic plastic.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex

• Three years on Camclosure® and ﬁxed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a ﬁve-year warranty.

•Two years on standard motorized or ﬁxed focal length lenses.

•Two years on Legacy ﬁxed dome products.

•Two years on Spectra continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of proﬁt and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

, Esprit®, ExSite™, and PS20 scanners, including when used in

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C2435M 7/01 Original version. C2435M-A 2/03 Revised per ECO#01-7241. Barrel locks replaced with tamper-resistant screws on in-ceiling models.