This Product Uses Lead (Pb) Free Solder Printed Circuit
Boards (PCBs).
Information regarding Lead-Free (PbF) solder:
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a mark following
the PCB part numbers in a label on the PCB.
Caution:
Pb free solder has a higher melting point than standard solder; typically
the melting point is 50 - 70 F (30 - 40 C) higher. Please use a soldering iron
with temperature control and adjust it to 700 20 F (370 10 C). Exercise care
while using higher temperature soldering irons, do not heat the PCB for too long
to prevent solder splash or damage to the PCB.
Pb free solder will tend to splash when heated too high (about 1100 F/600 C).
ECO SOLDER M705 (available from Senju Metal Industry Co., Ltd.:
URL: http://www.senju-m.co.jp) is recommended when repairing PbF PCBs.
The contents of this Service Manual and the Specifications are subject to change
without notice.
Panasonic Communications Co., Ltd. reserves the right to make improvements in
the product design without reservation and without notice.
Published in Japan.
o prevent severe injury and loss of life, read this section carefully before servicing the Panasonic
achine to ensure proper and safe operation.
lease ensure that the machine is installed near a wall outlet and is easily accessible.
his section explains the graphic symbols used in the machine and/or this manual.
WARNING:
Denotes a potential hazard that could result in serious injury or death.
CAUTION:
Denotes hazards that could result in minor injury or damage to the machine.
This section also explains the graphic symbols used in the machine and/or this manual.
These symbols are used to alert operators to a specific operating procedure
that must not be performed.
These symbols are used to alert operators to a specific operating procedure
that must be emphasized in order to operate the machine safely.
nstallation and Relocation Cautions
CAUTION
Do not place the machine near heaters or volatile, flammable, or combustible materials
such as curtains that may catch fire.
Do not place the machine in a hot, humid, dusty or poorly ventilated environment.
Prolonged exposure to these adverse conditions can cause fire or electric shocks.
Place the machine on a level and sturdy surface that can withstand.
If tilted, the machine may tip-over and cause injuries.
When relocating the machine, remove the toner and/or developer, and pack the machin
with proper packing materials for shipping.
When moving the machine, be sure to unplug the power cord from the outlet. If the
machine is moved with the power cord attached, it can cause damage to the cord which
could result in fire or electric shock.
ower and Ground Connection Cautions
WARNING
Ensure that the plug connection is free of dust. In a damp environment, a contaminated
connector can draw a significant amount of current that can generate heat and
eventually cause fire over an extended period of time.
Always use the power cord provided with your machine. When an extension power cord
is required, always use a properly rated cord.
120 V/15 A or AC 220 - 240V/10 A
If you use a cord with an unspecified current rating, the machine or plug may emit smok
or become hot to the touch externally.
Do not attempt to rework, pull, bend, chafe or otherwise damage the power cord. Do no
place a heavy object on the cord. A damaged cord can cause fire or electric shocks.
4
Never touch a power cord with wet hands. Danger of electric shock exists.
y.
O
O
If the power cord is broken or insulated wires are exposed, replace immediately with a specified cord onl
Using a damaged cord can cause fire or electric shocks.
Stop operation immediately if your machine produces smoke, excessive heat, unusual noise, or smell,
or if water is spilt onto the machine. These conditions can cause fire. Immediately switch Off and
unplug the machine.
Do not disconnect or reconnect the machine while it is on. Disconnecting a live connector can deform
the plug and cause fire.
When disconnecting the machine, grasp the plug instead of the cord. Forcibly pulling on a cord can
damage it and cause fire or electric shock.
When the machine is not used over an extended period of time, switch it Off and unplug it. If an unused
machine is left connected to a power source for a long period, degraded insulation can cause electric
shocks, current leakage or fire.
Be sure to switch Off and unplug the machine before accessing the interior of the machine for cleaning,
maintenance or fault clearance. Access to a live machines interior can cause electric shock.
Be sure to switch Off and unplug the machine before accessing the interior of the machine for
accessing interface cables, maintenance or fault clearance. Access to a live machines interior can
cause electric shock.
Once a month, unplug the machine and check the power cord for the following. If you notice any
unusual condition.
The power cord is plugged firmly into the receptacle.
The plug is not excessively heated, rusted, or bent.
The plug and receptacle are free of dust.
The cord is not cracked or frayed.
thers
The machine has a built-in circuit for protection against lightning-induced surge current. If lightning strikes in your
neighborhood, switch Off the machine. Disconnect the telephone line cable first, then unplug the power cord from
the machine and reconnect only when the lightning storm has stopped.
If you notice flickering or distorted images or noises on your audio-visual units, your machine may be causing
radio interference. Switch it Off and if the interference disappears, the machine is the cause of the radio interference. Perform the following procedure until the interference is corrected.
Move the machine and the TV and/or radio away from each other.
Reposition or reorient the machine and the TV and/or radio.
Unplug the machine, TV and/or radio, and replug them into outlets that operate on different circuits.
Reorient the TV and/or radio antennas and cables until the interference stops.
For an outdoor antenna, ask your local electrician for support.
Use a coaxial cable antenna.
perating Safeguards
WARNING
Do not touch areas where these caution labels are attached to the surface may be very hot, and cause
server burns.
Do not place any liquid container such as a vase or coffee cup on the machine. Spilt water can cause
fire or shock hazard.
Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get
into the machine, they can short-circuit internal components, and cause fire or electric shocks.
If debris (metal or liquid) gets into the machine, switch Off and unplug the machine.
Operating a debris-contaminated machine can cause fire or electric shock.
Do not try to alter the machine configuration or modify any parts. An unauthorized modification can
cause smoke or fire.
5
t
n
s
CAUTION
C
e
Do not place a magnet near the safety switch of the machine. A magnet can activate the
machine accidentally resulting in injuries.
Do not use a highly flammable spray or solvent near the machine. It can cause fire.
When copying a thick document, do not use excessive force to press it against the
document glass. The glass may break and cause injuries.
Never touch a labeled area found on or near the heat roller. You can get burnt. If a shee
of paper is wrapped around the heat roller, do not try to remove it when it is hot, to avoid
injuries or burns. Switch Off the machine immediately, and wait until it cools down.
Do not use conductive paper, e.g. folding paper, carbonic paper and coated paper. Whe
a paper jam occurs, they can cause a short circuit and fire.
Do not place any heavy object on the machine. An off-balance machine can tip-over or
the heavy object can fall, causing damage and/or injuries.
Keep the room ventilated when using the machine for an extended period of time to
minimize the ozone density in the air.
When copying with the document cover open, do not look directly at the exposure lamp.
Direct eye exposure can cause eye fatigue or damage.
Pull out paper trays slowly to prevent injuries.
When removing jammed paper, make sure that no pieces of torn paper are left in the
machine. A piece of paper remaining in the machine can cause fire. If a sheet of paper i
wrapped around the heat roller, or when clearing a jammed paper that is difficult or
impossible to see, do not try to remove it by yourself. Doing so can cause injuries or
burns. Switch Off the machine immediately, and wait until it cools down.
onsumable Safeguards
WARNING
Never throw a toner cartridge into an open flame. Toner remaining in the cartridge can
cause an explosion and you can get burnt.
Never throw toner or a waste toner container or a toner cartridge into an open flame. It
can cause an explosion and you can get burnt.
Keep button batteries out of the reach of children. If a button battery is swallowed
accidentally, get medical treatment immediately.
CAUTION
Never heat the drum cartridge, or scratch its surface. A heated or scratched drum can b
hazardous to your health.
Do not mix new and old batteries together. Otherwise, batteries can burst or leak,
causing fire or injuries.
Be sure to use the specified type of batteries only.
Ensure that batteries are installed with correct polarity. Incorrectly installed batteries can
burst or leak, resulting in spillage or injuries.
10.1. General Circuit Diagram .......................337
8
1Specifications Table
1.1.Control Panel
For USA only
Panafax UF-9000
For Americas
WORKiO DP-190
UF-9000
DP-180/190
For Euro and Other Destinations
WORKiO DP-180
Note:
LCD Display Brightness Adjustment
To adjust the brightness of the LCD display, press and while holding down the "CLEAR" key, keep
pressing the "ORIGINAL SIZE" or the "COPY SIZE" key until the desired brightness is achieved.
ORIGINAL SIZE : Dimmer
COPY SIZE: Brighter
Ver. 2. 0
9
JUN 2004
1.2.Copy Function
Copy Function
Items
UF-9000DP-180 / 190
Basic Specifications
1 TypeDesktop
2PlatenFixed
3 Original Position
PlatenLeft / Rear / Face Down
ADFLeft / Center / Face UP
4 Recording Paper PathCenter
5 DrumOrganic Photo Conductor (OPC)
6 Copy ProcessElectrostatic Indirect Laser
7 Developing Process
Mono Component Non Magnetic
8 Toner RecycleNo
9 Fusing SystemHeat & Pressure
10 Max Original SizeLetter / A4 / LegalLegal: with ADF only
11 Paper Size
Paper Tray
Bypass
12 Media Type
Standard TrayPaper / Transparency
Optional TrayPaper
Bypass
Paper / Transparency / Envelope /
13 Warm-up Time68 °F (20 °C)
Power Saver Mode
Sleep Mode
Shutdown Mode
Power On
14 First Copy TimeApprox. 10 sec
15 Copy Speed
Letter
A4Approx. 18 cpm
Description
Remarks
Dry Toner
Letter / LegalFor USA and Canada
A4 / A5For EU
A4 / A5 / B5For Other Destinations
Letter / Legal / InvoiceFor USA and Canada
A4, FLS, A5
For EU
FLS = 8 x 13 in, 8.5 x 13 in
A4 / A5 / B5 / PostcardFor Other Destinations
Label / Thick Paper
Approx. 15 sec
Approx. 18 sec
Scan: Platen; Size: Letter /
A4; Orientation: Portrait;
Paper Feed: 1st Paper Tray;
Interval: From Pressing of
Start Key to paper exiting to
the Exit Tray; When LSU is
ready.
Approx. 19 cpm
Paper Feed: 1st Paper Tray;
Paper Exit: to Exit Tray;
Continuous Copy Mode.
UF-9000
DP-180/190
Ver. 2. 0
10
JUN 2004
UF-9000
DP-180/190
Copy Function
Items
Description
Remarks
UF-9000DP-180 / 190
16 Zoom
EnlargementSelected Original size / Copy size
ReductionSelected Original size / Copy size
Zoom50 - 200%1% Step
17 Paper FeedFront Loading Universal Paper Tray
Paper Tray
Capacity250 sheets x 1
Low Level Paper WarningYes
LTR / A4: 20 lb (75 g/m
Orange Low Paper Level
Indicator
Bypass
Paper / Transparency /
Capacity1 sheet
Envelope / Label / Thick
Paper / Postcard etc.
Paper Capacity
(Std. Configuration)
250 sheets
18 Multi Copy Range999 sheets
19 Gradation
TextBi-Level
Text / Photo256 stepsHalftone by Error Diffusion
Photo256 steps
20 ResolutionScanning and Printing.
Scan
MonoMax. 600 x 600 dpi
ColorMax. 300 x 300 dpi
Selectable 600 dpi, with
Print (Mono)Max. 1200 (Interpolated) x 600 dpi
Smoothing, the results are
similar to PS3 / PCL6 Printers
(1200 dpi Interpolated).
21 Scanning type
Color ScanYes
Color Depth24 bit (16.7 Million colors)
Mono ScanYes
Standard Sorting Memory
22
Size
16 MB
23 Standard Page Memory Size32 MB
24 Exit Tray Capacity150 sheets
LTR / A4: 20 lb (75 g/m
25 Dimensions
18.2 x 19.9 x 20.6 in
(W x D x H)
(462 x 506 x 523 mm)
18.2 x 19.9 x 26.1 in
(462 x 506 x 663 mm)
With Optional 2nd Paper
Feed Module
26 Operating Space
(W x D)
18.2 x 21.1 x 31.5 in
(462 x 536 x 802 mm)
27 Weight48.5 lb (22 kg)
2
)
2
)
Ver. 2. 0
11
JUN 2004
UF-9000
DP-180/190
Copy Function
Items
Description
Remarks
UF-9000DP-180 / 190
Options
1Paper Feed System550 sheets x 1
550 sheets
2nd Paper Feed Module
Yes
Paper Size DetectionManualControl Panel Selectable
Low Level Paper WarningYes
Max. Paper Capacity800 sheets
Orange Low Paper Level
Indicator
LTR / A4: 20 lb (75 g/m
(Tray 1 + 2)
2 Sorting Image Memory
Optional Image Memory 1
(16 MB)
Optional Image Memory 2
(64 MB)
Optional Image Memory 3
(128 MB)
Yes
Yes
Yes
Unit comes standard with
16 MB.
1-Slot available for an
Optional Image Memory
module.
2-Page Copy ModeNo
2 in 1Yes
4 in 1Yes
Booklet ModeNo
Duplex Copy
1→2Yes
2→1YesScanning twice by turning
2→2Yes
original.
Book→2No
Image Rotation (90 or 270 °)No
Electronic SortingYes
Rotation SortingNo
Insertion JobNo
Department CounterYes50 Departments
ADF
Mixed Size Original FeedYes*
JOB Build and SADF
Mode
No
LTR and LGL, effective from
June 2004 Production
Original CounterNo
Job MemoryNoYes (1 jobs)
Job Time DisplayYes
Concurrent CopyNo
Tandem Copy ModeNo
Remote Copy ModeNo
Scan Once Print Many ModeYes
Job Completion Notice YesFor Printer Mode only
Trial Copy Mode No
Weekly TimerNo
Function ModeYes
InterruptNo
Electronic CounterYes
Digital Sky Shot ModeYes
Check : Dimensions of a Bank
Check / Slip Mode
(Double Exposure)
Yes
Slip : Dimensions of a Bank
check
check with a
statement
3Control Panel
DisplayLCD20 digits x 2 lines
GREEN : Scanning /
Status LampYes
Printing
RED: Alarm / Warning
UF-9000
DP-180/190
Ver. 2. 0
14
JUN 2004
Copy Function
Items
Description
Remarks
UF-9000DP-180 / 190
Key
QWERTY KeyboardYes
Directory Search (4 way)Yes
Original SizeYes
Copy SizeYes
KeypadYes
ClearYes
StopYes
StartYes
Energy SaverYes
Sort / FinishNo
Function ModeYes
Original Detection
Release
No
InterruptNo
ResetYes
One-Touch keyYes
Mode ChangeYes
Copier / Printer / NW Scanner
/ Fax and Internet Fax Mode
LCD Main Indication
Message Language
(Default)
Original Size / Image
Indication
Paper Size / Image
Indication
English (American)For USA and Canada
Specified Language
For EU and Other
Destinations
Yes
(without Image)
Yes
(without Image)
Paper Tray SelectionNo
Selected Paper Tray /
Tray Status
Yes
Original Mode SelectionYesText / Text-Photo / Photo
Copy Density SelectionYes5 steps
Setting ConfirmationYes
Function ClassificationYes
Zoom MagnificationYes
Number of CopiesYes
Error CodeYes
FinishingNo
UF-9000
DP-180/190
Ver. 2. 0
15
JUN 2004
Copy Function
Items
Description
UF-9000DP-180 / 190
Warning IndicatorsYes
No TonerYes
No PaperYes
Add Paper IndicationYesMechanical Indicator
Paper Jam IndicationYes
Paper Jam LocationYes
Service Alert CallYes
User ErrorYes
Machine ErrorYes
History of Jam ErrorsYes
ADF with Document GuideYes
Clip PocketNo
Operating Instructions
Pocket
Warning / Caution LabelSpecified Language
5Optical System
Original Size DetectionNo
Scanning Method600 dpi CCD
DehumidifierNo
6Process System / Yield
Yield: 5 K (5% coverage), 6 K Max
Average yield is based on 5% coverage of the printable area with
repetitive printing of 10 pages (Letter/A4 size, single side printing,
default density). The yield of a Toner Cartridge varies depending on the
Toner Cartridge
coverage, temperature, humidity, media, etc. Therefore, the average
yield cannot be guaranteed. Continuously printing 10% coverage of
printable area will reduce the yield of the Toner Cartridge to about half
as compared to 5% coverage printing. The maximum yield of the Toner
Cartridge will not exceed 6,000 pages by way of Digital Counter.
Additional Optional Sorting Image Memory
(Minimum 16 MB) is required for the Hard
Disk Drive to function.
(PS additional fonts, Mail Box, additional
800 addresses, etc.)
F-ROM Board (8 MB) is required for PCL
or PS printing.
Additional Memory for Fax / I-Fax
For Electronic Sorting
UE-403171For USA and Canada
UE-403172
For Other Destinations
Available in Specified Destinations
UF-9000
DP-180/190
■Supplies
UF-9000
Part NamePart NumberRemarks
Toner CartridgeUG-5530All in One Cartridge
DP-180/190
Part NamePart NumberRemarks
Toner
Drum Unit
Note:
PCL6 is a Page Description Language of the Hewlett-Packard Company.
PostScript 3 (PS3) is a Page Description Language of the Adobe Systems Company.
The Part Name(s) / Part Number(s) differ depending on the Models and the Destinations.
Complies with FDA radiation
performance standards, 21 CFR
Subchapter J
Left View
Top View
18.19 in (462 mm)
17.72 in (450 mm)
Front View
Manufacturer's Name and Address
19.89 in (505 mm)
20.57 in (522 mm)
16.65 in (423 mm)
17.65 in (448 mm)
Right View
Factory ID
Rear View
Ver. 2. 0
CAUTION
!
Denotes hazards that could result in minor injury or damage to the machine.
*THIS PRODUCT CONTAINS A LITHIUM BATTERY. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
"IMPROPER USE OR REPLACEMENT MAY CAUSE OVERHEATING, RUPTURE OR EXPLOSION RESULTING IN
INJURY OR FIRE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS OF YOUR LOCAL
SOLID WASTE OFFICIALS AND LOCAL REGULATIONS"
Note: The service life of the Battery is approximately 1 year under normal use.
30
JUN 2004
Loading...
+ 338 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.