Panasonic TH-L32C20K, TH-L32C20M, TH-L32C23K, TH-L32C26K, TH-L32C28K User Manual

...

Speci cations

Receiving Systems / Band name

1 PAL B, G, H

Reception of broadcast transmissions and Playback from Video Cassette Tape Recorders

NTSC 4.43/5.5 MHz

Playback from Special VCR’s or DVD

2 PAL I 9

NTSC 4.43/6.0 MHz

3 PAL D, K 10

NTSC 4.43/6.5 MHz

4 SECAM B, G 11

NTSC 3.58/5.5 MHz

5 SECAM D, K 12

NTSC 3.58/6.0 MHz

6 SECAM K1 13

NTSC 3.58/6.5 MHz

NTSC M (NTSC 3.58/4.5 MHz)

14 SECAM

PAL 60 Hz/5.5 MHz

Playback from Special Disc Players and Special VCR’s or DVD

PAL 60 Hz/6.0 MHz

PAL 60 Hz/6.5 MHz

Printed in Malaysia

Web Site: http://panasonic.net/ © Panasonic Corporation 2010

Design and Speci cations are subject to change without notice. Weight and Dimensions shown are approximate.

TH-L32C2S,

TH-L32C20K/T/X,

TH-L32C23K, TH-L32C26K,

TH-L32C28K

TH-L32C20M TH-L32C20R

Power Source

AC AUTO 110-240 V, 50 / 60 Hz

AC 110-240 V, 50 / 60 Hz

AC Single 220-240 V, 50 / 60 Hz

Power

Consumption

Average use 93 W

Standby condition 0.3 W

Display

panel

Aspect Ratio 16:9

Visible screen size

80 cm (diagonal) 698 mm (W) × 393 mm (H)

Number of pixels 1,049,088 (1,366 (W) × 768 (H))

Sound

Speaker 160 mm × 40 mm × 2 pcs, 8 Ω

Audio Output 20 W (10 W + 10 W), 10% THD

PC signals

VGA, SVGA, WVGA, XGA SXGA, WXGA ······ (compressed) Horizontal scanning frequency 31 - 69 kHz Vertical scanning frequency 59 - 86 Hz

Receiving Channels (Regular TV)

PAL B/G 2-12 (PAL/SECAM B, K1) 0-12 (PAL B AUST.) 1-9 (PAL B N.Z.) 1-12 (PAL/SECAM D) 1-12 (NTSC M Japan) 2-13 (NTSC M USA)

UHF BAND 21-69 ( PAL G, H, I/

SECAM G, K, K1) 28-69 (PAL B AUST.) 13-57 (PAL D, K) 13-62 (NTSC M Japan) 14-69 (NTSC M USA)

CATV S1-S20 (OSCAR) 1-125 (USA CATV) C13-C49 (JAPAN) S21-S41 (HYPER) Z1-Z37 (CHINA) 5A, 9A (AUST.)

Aerial - Rear VHF / UHF

Operating Conditions

Temperature : 0 °C - 40 °C Humidity : 20 % - 80 % RH (non-condensing)

Connection Terminals

AV1 Input

AUDIO L - R RCA PIN Type × 2 0.5 V[rms] VIDEO RCA PIN Type × 1 1.0 V[p-p] (75 Ω)

COMPONENT

Y P

B/CB

, PR/C

1.0 V[p-p] (including synchronization) ±0.35 V[p-p]

AV2 Input

AUDIO L - R RCA PIN Type × 2 0.5 V[rms] VIDEO RCA PIN Type × 1 1.0 V[p-p] (75 Ω)

Monitor Output

AUDIO L - R RCA PIN Type × 2 0.5 V[rms] VIDEO RCA PIN Type × 1 1.0 V[p-p] (75 Ω)

Others

PC Input

HIGH-DENSITY D-SUB 15PIN

R, G, B/0.7 V[p-p] (75 Ω)

HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance) HDMI Input TYPE A Connectors  is TV supports “HDAVI Control 5” function. Card slot SD Card slot × 1

Dimensions ( W × H × D )

798 mm × 551 mm × 217 mm (With Pedestal) 798 mm × 511 mm × 93 mm (TV only)

Mass

10.0 k

Net (With Pedestal)

9.0 k

Net (TV only)

Licence

Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

• VGA is a trademark of International Business Machines Corporation.

• S-VGA is a registered trademark of the Video Electronics Standard Association.

• HDMI, the HDMI Logo and HighDe nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

• HDAVI Control

is a trademark of

Panasonic Corporation.

• Macintosh is a trademark of Apple Inc.

 is product incorporates the following so ware:

(1) so ware developed independently by or

for Panasonic Corporation,

(2) so ware owned by a third party and

licensed to Panasonic Corporation,

(3) so ware licensed under the GNU General

Public License, Version 2 (GPL v2),

(4) so ware licensed under the GNU LESSER

General Public License (LGPL) and/or,

(5) open source so ware other than so ware

licensed under the GPL and/or LGPL

For the so ware categorized as (3) or (4), please refer to the terms and conditions of GPL v2 and LGPL, as the case may be. at http://www.gnu.org/licenses/old-licenses/gpl-

2.0.html and http://www.gnu.org/licenses/ old-licenses/lgpl-2.1.html In addition, so ware categorized as (3) or (4) is copyrighted by several individuals and/ or entities. Please refer to the copyright notice of those individuals at http://www.am-linux.jp/dl/DTV10AT/

GPL/LGPL SOFTWARE IS DISTRIBUTED IN THE HOPE THAT IT WILL BE USEFUL, BUT WITHOUT ANY WARRANTY, EXPRESS, IMPLIED OR STATUTORY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. For at least three (3) years from delivery of products, Panasonic will give to anyone who contacts us at the address provided below, for a charge of no more than our cost of physically performing source code distribution, a complete machine-readable copy of the corresponding source code covered under GPL v2/LGPL. Contact Information cdrequest@am-linux.jp Source code is also freely available to you and any other member of the public via our website below. http://www.am-linux.jp/dl/DTV10AT/

Operating

Instructions

Remote Control

N2QAYB000543

Batteries for the

Remote Control (2)

• R6 (AA)

Pedestal

Check that you have the accessories and items shown

Standard accessories

EXIT

TEXT

F.P. INDEX

HOLD

SURROUND

OPTION

RETURN

MUTE

RECALL

RGYB

POWER

OFF TIMER

ASPECT

INPUT

Pedestal hole cover

sheet (Not applicable for TH-L32C20M, TH-L32C20R)

English

 ank you for purchasing this Panasonic product. Please read these instructions before operating your set and retain them for future reference.  e images shown in this manual are for illustrative purposes only. CAUTION:  is product contains possibly dangerous parts (such as plastic bags), that can be breathed in or swallowed by young children accidentally. Keep these parts out of reach of young children.

BBN

TQB4GC0478-1

Operating Instructions

LCD TV

Model No.

TH-L32C2S TH-L32C20T TH-L32C20K TH-L32C20X TH-L32C20M TH-L32C23K TH-L32C20R TH-L32C26K

TH-L32C28K

– Safety Precautions .................................................. 2

– Attaching the pedestal ........................................... 3

– Inserting and removing remote’s batteries ......... 3

– Connecting the Aerial & External Equipment ... 4

– Identifying Controls ............................................... 5

– Performing Initial Setup & Watching TV ........... 6

– Viewing Teletext ..................................................... 7

– Using Menu Functions ........................................... 8

– Stereo / Bilingual Sound Selection .................... 12

– VIERA Link “HDAVI Control

” ...................... 12

– VIERA TOOLS .....................................................13

– Viewing from SD Card

(VIERA IMAGE VIEWER) ................................14

– Watching External Inputs .................................... 14

– Input signals that can be displayed ..................... 15

– FAQs ....................................................................... 15

– Speci cations ......................................................... 16

Contents

If you  nd any

abnormality,

remove the mains

plug immediately!

Mains plug types vary between

countries.

Safety Precautions

Warning

Power source / Installation

•

 is TV is designed for :

– TH-L32C2S, TH-L32C20K/T/X,

TH-L32C23K, TH-L32C26K,

TH-L32C28K :

AC AUTO 110-240 V, 50 / 60 Hz

– TH-L32C20M :

AC 110-240 V, 50 / 60 Hz

– TH-L32C20R :

AC Single 220-240 V, 50 / 60 Hz

– Table-top use

Handling the mains plug and lead

•

Insert the mains plug fully into the socket outlet. (If

the mains plug is loose, it could generate heat and

cause  re.)

• Ensure that the mains plug is easily accessible.

• Do not touch the mains plug with a wet hand. ( is may cause electrical shock.)

• Do not damage the mains lead. (A damaged lead may cause  re or electrical shock.)

– Do not move the TV with the lead plugged into the socket outlet.

– Do not place heavy objects on the lead nor place the lead near a high-temperature

object.

– Do not twist the lead, bend it excessively, or stretch it.

– Do not pull on the lead. Hold onto the mains plug body when disconnecting lead.

– Do not use a damaged mains plug or socket outlet.

Do not remove covers and NEVER modify the TV yourself

•

Do not remove the rear cover as live parts are accessible when it is removed.  ere are

no user serviceable parts inside. (High-voltage components may cause serious electrical

shock.)

• Have the TV checked, adjusted, or repaired by your local Panasonic dealer.

Do not expose to rain or excessive moisture

•

To prevent damage which might result in electric shock or  re, do not expose this TV to

rain or excessive moisture.  is TV must not be exposed to dripping or splashing water

and objects  lled with liquid, such as vases, must not be placed on top of or above the

TV.

Do not expose to direct sunlight and other sources of heat

•

Avoid exposing the TV to direct sunlight and other sources of heat. To prevent  re never

place any type of candle or naked  ame on top or near the TV.

Do not insert foreign objects into the TV

• Do not allow any object to drop into the TV through the air vents. (Fire or electrical

shock may result.)

Caution

■  is appliance is intended for use in tropical climates

■ When cleaning the TV, remove the mains plug

– Cleaning an energized TV may cause electrical shock.

■ When the TV is not going to be used for a long period of time, remove the mains plug

–  is TV will still consume some power even in the O mode, as long as the mains

plug is still connected to a live socket outlet.

■ Allow su cient space around the TV for radiated heat

– When using the pedestal, keep a space between the bottom of the TV and the surface

where the TV is set.

– In case of using Wall-hanging bracket, follow

the manual of it.

■ Do not block the rear air vents

– Blocked ventilation by newspapers, table

cloths, curtains, etc. may cause overheating,

 re or electrical shock.

■ Do not apply strong force or impact to the

display panel

–  is may cause damage resulting in injury.

Do not place the TV on sloped or unstable surfaces

•

 e TV may fall o or tip over.

Use only the dedicated pedestals / mounting equipment

•

Using an unapproved pedestal or other  xtures may make the TV unstable, risking

injury. Be sure to ask your local Panasonic dealer to perform setup.

• Use approved pedestals (p. 3) / wall-hanging brackets (p. 3).

Do not allow children to handle SD Card

•

As with any small object, SD Cards can be swallowed by young children. Please remove

SD Card immediately a er use and store out of reach of children.

10 10 10

Minimum distance (cm)

NOTE

■ Auto power standby function

–

If no signal is received and no operation is performed for 30 minutes, the TV will

automatically go to standby mode.

■ Keep the TV away from these types of equipment

– Electronic equipment

In particular, do not place video equipment near the TV. Electromagnetic interference

may distort images / sound.

– Equipment with an infrared sensor

 is TV also emits infrared rays.  is may a ect operation of other equipment.

■ Transport only in upright position

TH-L32C20KMRTX23,26,28K_EN_Folding.indd Sec1:2 5/25/2010 3:27:46 PM

200mm

Rear of the TV

Holes for wall-hanging bracket installation

Depth of screw:

minimum: 10 mm

maximum: 12 mm

Screw for  xing the TV onto the wall-hanging bracket (not

supplied with the TV)

[View from the side]

Attaching the pedestal

Inserting and removing remote’s batteries

WARNING

Do not disassemble or modify the pedestal.

•

Otherwise the TV may fall over and become damaged, and personal injury may result.

CAUTION

Do not use the pedestal for any other TV or displays.

•

Otherwise the TV or the display may fall over and become damaged, and personal

injury may result.

Do not use the pedestal if it becomes warped or physically damaged.

• If you use the pedestal while it is physically damaged, personal injury may result.

Contact your nearest Panasonic dealer immediately.

During set-up, make sure that all screws are securely tightened.

• If insu cient care is taken to ensure screws are properly tightened during assembly,

the pedestal will not be strong enough to support the TV, and it might fall over and

become damaged, and personal injury may result.

Ensure that the TV does not fall over.

• If the TV is knocked or children climb onto the pedestal with the TV installed, the TV

may fall over and personal injury may result.

Two or more people are required to install and remove the TV.

• If two or more people are not present, the TV may be dropped, and personal injury

may result.

Assembly screws

(4)

Assembly screws

(4)

Bracket (1)

Base (1)

Wall-hanging bracket (Optional)

Please contact your nearest Panasonic dealer to purchase the

recommended wall-hanging bracket. For additional details, please

refer to the wall-hanging bracket installation manual.

WARNING

•

Using other wall-hanging brackets, or installing a wall-hanging bracket by yourself

have the risk of personal injury and product damage. In order to maintain the unit’s

performance and safety, be absolutely sure to ask your dealer or a licenced contractor to

secure the wall-hanging brackets. Any damage caused by installing without a quali ed

installer will void your warranty.

• Do not mount the unit directly below ceiling lights (such as spotlights,  oodlights or

halogen lights) which typically give o high heat. Doing so may warp or damage plastic

cabinet parts.

• Take care when  xing wall brackets to the wall. Always ensure that there are no electrical

cables or pipes in the wall before hanging bracket.

• To prevent fall and injury, remove the TV from its  xed wall position when it is no

longer in use.

Pull open

Hook

Note the correct

polarity (+ or -)

CAUTION

•

Incorrect installation may cause battery

leakage and corrosion, resulting in damage

to the remote control.

• Do not mix old and new batteries.

• Do not mix di erent battery types (such as

alkaline and manganese batteries).

• Do not use rechargeable (Ni-Cd) batteries.

• Do not burn or breakup batteries. Batteries

must not be exposed to excessive heat such

as sunshine,  re or the like.

• Do not disassemble or modify the remote

control.

Foam mat or thick

so cloth

TY-WK3L2RW

Assembling the pedestal

Use the assembly screws

to fasten the bracket to

the base securely.

• Make sure that the screws are securely tightened.

Securing the TV

Insert the bracket into the TV, and then fasten securely

with the assembly screws

• Make sure that the screws are securely tightened.

Front

TH-L32C20KMRTX23,26,28K_EN_Folding.indd Sec1:3 5/25/2010 3:27:46 PM

AV IN

HDMI

Rear of TV

DVD Recorder /

VCR

To record / playback

(Listening)

Conversion adapter

(if necessary)

Computer

(Viewing)

To watch DVDs

DVD player

RF cable

Aerial

To watch satellite

broadcasts

Satellite

dish

Satellite

cable

Set top box

Fully wired HDMI

compliant cable

HDMI equipment

DVD player

Fully wired HDMI

compliant cable

(Listening) (Viewing)

Ampli er with

speaker system

RCA cable

(Viewing)

(Listening)

To listen with speakers

Camcorder /

Game equipment

Connecting the Aerial & External Equipment

NOTE

•

If the aerial is placed in the wrong

location, interference might happen.

• Do not put the RF cable close to the

mains lead to avoid noise.

• Do not place the RF cable under the TV.

• To obtain optimum quality picture and

sound, an aerial, the correct cable

(75 Ω coaxial) and the correct

terminating plug are required.

• If a communal aerial system is used,

you may require the correct connection

cable and plug between the wall aerial

socket and the TV.

• Your local Television Service Centre

or dealer may be able to assist you in

obtaining the correct aerial system for

your particular area and the accessories

required.

• Any matters regarding aerial

installation, upgrading of existing

systems or accessories required, and the

costs incurred, are the responsibility of

you, the Customer.

 ese diagrams show our recommendations for how to connect the TV to your various equipment. For other connections,

please refer to the operating instructions of each equipment.

External equipment and cables shown are not supplied with this TV.

Please ensure that the TV is disconnected from the mains socket before attaching or disconnecting any leads.

TH-L32C20KMRTX23,26,28K_EN_Folding.indd Sec1:4 5/25/2010 3:27:48 PM

EXIT

TEXT

F.P. INDEX

HOLD

SURROUND

OPTION

RETURN

MUTE

RECALL

RGYB

POWER

OFF TIMER

ASPECT

INPUT

Remote controlTV

1 Standby On / O switch

•

Switches TV On or O standby

When the TV is switched to

standby, there will be a clicking

sound a er a short delay.  is

is normal.

2 Selects stereo/bilingual sound

(p. 12)

3 Main Menu (p. 8)

•

Accesses the Main Menu

4 Aspect (p. 6)

•

Displays the Aspect Selection list

• It is also possible to select the

desired aspect by pressing this

button repeatedly

5 VIERA TOOLS (p. 13)

•

Displays some special feature

icons for easy-access

6 VIERA Link (p. 13)

•

Accesses VIERA Link Menu

7OK

•

Con rms selections

8 Option Menu (p. 6)

•

Quick access to some viewing and

listening options

9 Teletext (p. 7)

• Switches to teletext mode

10 Switches to the favourite teletext

page (p. 7)

11 Numeric buttons

•

Selects channel and teletext pages

• When in Standby mode, switches

TV On

12 Sound Mute

• Switches sound mute On or O

13 Volume Up / Down

14 Input mode selection

•

PC: switches to PC input mode

• TV: switches to TV mode

• AV: displays Input Selection list

O Timer (p. 6)

• Sets the TV to turn to standby

automatically a er a period of

time

16 Surround (p. 9)

•

Switches Surround e ect On or

O

17 Exit

• Returns to the normal viewing

screen

18 SD Card

• Switches to SD Card viewing mode

(p. 14)

19 Cursor buttons

•

Makes selections or adjustments

20 Return

•

Returns to the previous menu /

page

21 Coloured buttons

• Selects, navigates and operates

various functions

22 Hold (p. 7)

•

Holds the current teletext page

(teletext mode)

23 Index (p. 7)

•

Returns to the teletext index page

(teletext mode)

24 Programme Information

25 Channel Up / Down

•

Selects channel in sequence

Identifying Controls

1 SD card slot

2 Remote control signal receiver

•

Do not place any objects between the TV

remote control signal receiver and remote

control.

3 Power LED

• Standby: red

On: green

• When using the remote control, indicates

the TV has received a command.

4 Function Select

• Volume / Backlight / Contrast /

Brightness / Colour / Sharpness / Tint

(NTSC mode) / Bass / Treble / Balance /

Auto Tuning (p. 8 - 9)

5 Increases or decreases the channel

position by one. When a function is

already displayed, press to increase or

decrease the selected function. When in

standby mode, switches TV on.

6 Changes the input mode

7 Mains power On / Off switch

•

Switch On to turn on the TV or turn

the TV to Standby mode by the remote

control.

TH-L32C20KMRTX23,26,28K_EN_Folding.indd Sec1:5 5/25/2010 3:27:49 PM

Channel Plan

Hong Kong

CIS/E.Europe

China

Asia/W.Europe

NZ/Indonesia

CATV/Other

Auto Tuning

Scan

120

CH2

OSD Language

English

Please select your viewing environment.

Home Shop

select

access

select

set

select

set

CH07

5.5MHz

PAL

16:9

Input mode, channel position, channel number, Sound

system, Colour system (not displayed if set to “Auto”),

aspect ratio

Sound mute, audio

mode, teletext

indication (if teletext

is available), O timer

remaining time

(Also appears when changing channel)

Aspect Selection

16:9

Just

4:3

4:3 Full

Zoom1

Zoom2

Zoom3

14:9

select change

Select

Store

Turns the TV to standby a er a period of time

(0 / 15 / 30 / 45 / 60 / 75 / 90 minutes)

Quick access to the selectable settings for the

current programme

Views information banner

Channel Colour Set

Sets colour density Picture Menu (p. 8)

Teletext Character Set

Sets the teletext language

Setup Menu (p. 9)

MPX

Selects multiplex sound (if available)

Sound Menu (p. 9)

Volume Correction

Adjusts volume of individual programme or input

mode

Sound Menu (p. 9)

Change aspect ratio

You can also change the aspect directly

Press repeatedly until the desired mode

is reached

• Only “16:9” and “4:3” are available in PC input mode.

• Aspect is  xed to “16:9” when “Viewing Mode” is set

to “Game” in the Picture Menu.

• Not available in teletext mode.

• Aspect mode can be memorized separately for each

SD (Standard de nition) and HD (High de nition)

signals and also for each input.

• To cancel Set to “0” or turn the TV o .

• When the remaining time is within 3 minutes, the

remaining time will  ash on screen.

Press repeatedly until the desired time

is reached

While the list is displayed, select the mode (16:9 /14:9 /

Just / 4:3 / 4:3 Full / Zoom1 / Zoom2 / Zoom3)

Performing Initial Setup & Watching TV

Search and store TV channels automatically.

 ese steps are not necessary if the setup has been completed

by your local dealer.

Auto Tuning will start to search for TV channels and store

them.  e sorted channel order depends upon the TV signal,

the broadcasting system and reception conditions.

When selecting “CATV/Other”, press the OK button, and

then select the Channel Plan from “Indian CATV”, “South

Africa”, “American System”, “American CATV” or “Japan”.

Auto Tuning starts

Auto Tuning is complete

To change the viewing environment mode later on, reset all settings by accessing Shipping Condition.

“Shipping Condition” (p. 10)

Your TV is now ready for viewing. To select a channel Remote control in Identifying Controls (p. 5)

While watching the TV, you can do the following:

Select your language

Select your area

Select “Home”

Viewing environment mode

Home: For viewing at home. Select “Home” for optimal picture. “Viewing Mode” is set as “Normal” (p. 8).

Shop: Demonstration mode (for in-store display). “Viewing Mode” is set as “Dynamic” (p. 8).

To return to viewing environment selection mode if you selected “Shop”

Plug the TV into the mains socket and switch On

You can now use the remote control to

turn On the TV or switch the TV to

standby mode. (Power LED: On)

Please select your viewing environment.

Home Shop

Shop

You have selected shop mode

Automatic Demo

Off On

Display the Aspect Selection list

TH-L32C20KMRTX23,26,28K_EN_Folding.indd Sec1:6 5/25/2010 3:27:50 PM

17:51 28 Feb

TELETEXT

INFORMATION

Sub page number

In FASTEXT mode, four di erently coloured subjects

are situated at the bottom of the screen. To access more

information about one of these subjects, press the

corresponding coloured button.

In List mode, four di erently coloured page numbers

are situated at the bottom of the screen of which each

can be altered and stored in the TV’s memory “Store

frequently viewed pages in the colour bar”.

To change mode

“Teletext” in Setup Menu (p. 9)

Switch to Teletext

• Displays Index (content varies depending on

the broadcasters)

Select the page (up to page 899)

(Corresponds to the colour bar)

• To return to TV or

Reveal hidden data (e.g. quiz page answers)

(Press again to hide)

Expand the teletext page

If you wish to hold the current page without

updating

(Press again to resume)

Stop automatic updating

Return to the main index page

Store frequently viewed pages in the colour bar

(List mode only)

As page is displayed:

Corresponding

colour button

To change stored pages

Press

Colour button you

want to change

Enter new

page number

Press

•

Call up the page stored in the blue button,

even while you are watching TV

• Factory setting is “P103”

View a stored favourite page (List mode only)

Time / date

Current page

number

Colour bar

down

• To adjust contrast

(Press 3 times)

As the blue bar is

displayed

Teletext functions

Viewing Teletext

Press repeatedly to expand the TOP

half, BOTTOM half or show FULL

page

Appears at the bottom of

the screen

108

Watch TV and teletext in two windows at once

View sub page (only when teletext is more than one

page)

 e number of sub pages varies depending on the

broadcasters. It may take some time for searching,

during which time you can watch TV.

Enter the 4-digit number

example: P6

View the TV picture while searching for a teletext

page or waiting for automatic update

Appears

when

updating is

completed

Changes to TV screen temporarily

(You cannot change the programme.)

View the updated page

 e news page provides a function that indicates

arrival of latest news (“News Flash”).

•

Operations can be made only in teletext screen

(press twice)

To view speci c sub page

Broadcast

Select teletext only

or picture / teletext

TH-L32C20KMRTX23,26,28K_EN_Folding.indd Sec1:7 5/25/2010 3:27:51 PM

A2 Landscape - en.indd 1A2 Landscape - en.indd 1 5/25/2010 3:29:14 PM5/25/2010 3:29:14 PM

select

access

Select

EXIT Change RETURN

Page up

Page down

Sound Menu

1/2

Mode Music

Bass Treble Balance Surround Volume Correction Speaker Distance to Wall Over 30cm MPX

Off

Stereo

(example)

Main Menu

Picture

Sound

Setup

• Choose from among alternatives

• Adjust using the slide bar

• Go to the next screen

Colour Balance

Normal

Changed

Number and positions of alternatives

Sharpness 50

Moved

Tuning Menu Access

Displays the next screen

select item

change setting

store or access

(required by some functions)

Picture Menu

1/2

Viewing Mode Normal

Contrast Brightness Colour Sharpness Tint Colour Balance Channel Colour Set

Normal

50 50

Backlight

Various menus allow you to make settings for the picture, sound and other functions.

Using Menu Functions

When you are not sure how to

operate, refer to the on-screen operation guides for help.

On-screen operation guide

Menu List & Functions

Picture Menu - Settings for picture

Viewing Mode

Basic picture mode (Dynamic / Normal / Cinema / Game)

• In each Viewing Mode; Backlight, Contrast, Brightness, Colour, Sharpness, Tint, Colour

Balance and 3D-COMB can be adjusted and stored to your preference

• Set for each input signal

Dynamic : Provides enhanced picture contrast and sharpness when viewing in a

bright room Normal : Recommended for viewing under normal lighting conditions Cinema : For watching movies in a darkened room with improved performance of

contrast, black and colour reproduction

Game : Fast response signal speci cally to provide suitable images for playing games

–

Not valid on TV mode.

– A continuous record of time spent in Game mode can be displayed in the top

right of the screen

“Playing Time Display” (p. 9).

• When SD Photo input is selected, the picture mode options will be

(Dynamic / Normal / Photo)

Backlight Contrast Brightness Colour Sharpness

Increases or decreases

the levels of these options according to your personal preference

Tint

With an NTSC signal source connected to the TV, the picture hue can be

adjusted to suit your taste

• For NTSC or Component / HDMI input signal reception only.

Colour Balance

Allows you to set the overall colour tone of the picture

(Cool / Normal / Warm)

Channel Colour Set

Colour density varying between broadcast channels can be

adjusted to three levels for each reception channel

• Select the channel you want to adjust and set this function.

P-NR

A picture noise reduction function which automatically reduces unwanted

picture and  icker noise in the contoured parts of a picture (O / Min / Mid / Max)

• Not valid on PC signal.

3D-COMB

Makes still or slow moving pictures look more vivid (O / On)

• Occasionally, while viewing still or slow moving pictures, colour patterning may be

seen. Set to “On” to display sharper and more accurate colours.

• For PAL or NTSC signal reception only.

• Not valid on Component, PC, HDMI and SD card.

Advanced PC Settings

R-Gain, G-Gain, B-Gain

Adjusts each gain

Gamma

Changes the gamma curve (2.0 / 2.2 / 2.5) Reset to Defaults Press the OK button to reset the present Advanced PC Settings to the default.

Reset to Defaults

Press the OK button to reset the present Picture Menu settings

to the default.

•

To return to TV at any time

• To return to the

previous screen

• To change menu

pages

Select the menu

Display the menu

Displays the functions that can be set (varies according to the input signal)

Select the item and change the setting

down

Sound Menu - Settings for sound

Mode

Basic sound mode (Music / Speech / User)

•

 e selected mode a ects all input signals.

Music : Improves sound quality for watching music video, etc. Speech : Improves sound quality for watching news, drama, etc.

•

In Music and Speech mode, you can adjust the “Bass” and “Treble” settings, and those settings will be stored for each mode.

User : In this mode, “Equalizer” will appear in the Sound Menu instead of “Bass”

and “Treble”. Adjust the “Equalizer” to your preference “Equalizer” (below)

Bass

Adjusts the bass level

Tre b le

Adjusts the treble level

Equalizer

Adjusts the frequency level to suit your favourite sound quality

• Wit h / button, select a frequency band, then with / , adjust its level.

• If you want to enhance the bass sound, raise the level of the lower frequency. If you want

to enhance the treble sound, raise the level of the higher frequency.

• To reset the level of each frequency to the default settings, select “Reset to Defaults” with

the cursor button, then press the OK button.

Balance

Adjusts the volume level of right and le speakers

Surround

Surround sound settings (O / V-Audio)

V-Audio: Provides a dynamic enhancer to simulate improved spatial e ects

• Switching is also possible by the Surround button on the remote control (p. 5).

Volume Correction

Adjusts the volume of individual channel or input mode

Speaker Distance to Wall

Adjusts the low frequency sound

(Over 30cm / Up to 30cm)

• If the back space between the TV and wall is over 30 cm, select “Over 30cm”.

• If the back space between the TV and wall is within 30 cm, select “Up to 30cm”.

MPX

Selects multiplex sound mode (if available) (p. 12)

• Normally : Stereo

• Stereo signal cannot be received : Mono

• M1 / M2 : Available while mono signal is transmitted

HDMI Input

Select to  t the input signal (Digital / Analogue)

Digital : HDMI cable connection Analogue : HDMI-DVI adapter cable connection

•

HDMI input mode only.

Reset to Defaults

Press the OK button to reset the present settings of Mode,

Balance and Surround in Sound Menu to the default.

Setup Menu - Settings for TV

PC Setup

Input Resolution

Switches to wide view

– VGA (640 × 400 pixels, 640 × 480 pixels), WVGA (852 × 400 pixels, 852 × 480 pixels),

XGA (1,024 × 768 pixels), WXGA (1,280 × 768 pixels, 1,366 × 768 pixels)

– Options change depending on signals

Clock Set to the minimum level if noise occurs H-pos Adjusts screen horizontal position with / button V-p os Adjusts screen vertical position with / button Clock Phase Eliminates  icker and distortion. Adjust a er Clock adjustment and

set to the minimum level if noise occurs. Sync PC sync signal type (H & V / On Green)

– H & V : by the horizontal and vertical signals from your PC – On Green : by green signal from your PC

Reset to Defaults Press the OK button to reset the present PC Setup settings to the default.

O Timer

Sets the time the TV automatically goes to Standby mode

(O / 15 / 30 / 45 / 60 / 75 / 90 minutes)

Child Lock

Locks a channel / AV input to prevent access to it (p. 10)

Tuning Menu

Channel List Edit

Skips the unwanted channels or edits channels (p. 11)

Auto Tuning Sets TV channels automatically (p. 11) Manual Tuning Sets TV channels manually (p. 11)

OSD Language

Changes language for on-screen displays

(English /

/ / / / / Indonesia / Français)

Display Settings

Te le t e x t

Teletext display mode (FASTEXT / List) (p. 7)

Teletext Character Set

Selects teletext language (English / CIS / E.Europe /

Persian) Input Labels

Labels or skips each input terminal (p. 10)

Playing Time Display

Set to “On” to display a continuous record of time spent in

Game mode every 30 mins (O / On)

–  is function is available when “Game” is selected in “Viewing Mode”.

Continued p. 10

Child Lock

Change PIN

Child Lock List Access

Child Lock List - TV and AV

kcoLemaN

1 2 Lock 3 Lock 4 Lock 5 Lock 6 Lock 7 Lock 8

Lock

Child Lock-PIN Entry

Please enter new PIN

PIN * * * *

For your convenience, you can label each input terminal or skip any unused terminal.

Select an input terminal and set

You can lock speci c channels / AV input terminals and control who watches them. When the locked channel / input is selected, a message appears; by entering the PIN number, you can watch it.

Set

Input Labels

 e labels you set will be displayed in “Input Selection” menu (p. 14) or banner.

• If “Skip” is selected, you cannot select the mode.

Control channel audience (Child Lock)

Enter the PIN number (4 digits)

(enter twice if  rst setting)

Select the channel / input to be locked

Select “Child Lock List”

VIERA Link Settings

VIERA Link

Sets to use VIERA Link functions (O / On)

Power on Link When the connected equipment starts playback or direct

navigator / function menu for the equipment is activated, the TV is automatically turned on. (Only when the TV is in Standby mode.) (O / On) Power o Link When the TV is set to Standby mode, the connected equipment is also automatically set to Standby.  is function will work even if the TV enters standby mode automatically by O Timer function or auto power standby function.

(O / On) Standby Power Save

†

¹  is function is available when “VIERA Link” and “Power

o Link” are set to “On”. It controls the power consumption in Standby mode of the connected equipment to reduce the power consumption (O / On)

Intelligent Auto Standby

†

¹  is function is available when “VIERA Link” is set to

“On” . It makes non-used connected equipment go into Standby mode to reduce the power consumption (O / On (With reminder) / On (No reminder))

†

¹ Only e ective if the connected equipment supports this function.

System Menu

Shipping Condition

Resets all settings to the original condition. A er performing this function, “Initial Setup” (p. 6) will automatically start when Mains power On / O switch is next turned On.

So ware Licence Displays the so ware licence information System Information Displays the system information of this TV

Other Settings

AV Colour System

Selects optimum colour system based on video signals in AV mode (Auto / PAL / SECAM / M.NTSC / NTSC) Colour Matrix Available only with 480p or 576p input on video signals in a natural colour from digital equipment connected to AV1 component or HDMI terminal. Select SD or HD to adjust suitable colour parameters for SD (standard de nition) or HD (high de nition)

– SD : Input signal is a normal TV system – HD : Input signal is a high de nition system

Auto Standby Sets the TV to automatically goes to Standby mode when no operation is performed within the selected period (O / 2 hours / 4 hours) Automatic input switching with the connected equipment a ects this function and time-count will be reset. A noti cation message will appear 3 minutes before going into Standby mode.

Power Save Reduces picture brightness to reduce power consumption (O / On) 16:9 Overscan Selects the screen area for displaying the image (O / On)

– On : Enlarges the image to hide the edge of the image – O : Displays the image in the original size – Set to “On” if noise is generated on the edges of the screen. –  is function is available when aspect is set to “16:9”. –  is function can be memorized separately for SD (Standard De nition) and HD

(High De nition) signals.

• Only available items can be selected.

• A di erent menu will be displayed in the mode of SD Card (p. 14).

VIERA Main Menu Child LockSetup

VIERA Main Menu Display Settings Input LabelsSetup

Appears when the channel / input is locked

•

To cancel

Select the locked channel /

input

•

To lock all

•

To cancel all locks

•

To change the PIN number

Select “Change PIN” in

“Child Lock” and enter a new PIN number twice

NOTE

Performing “Shipping Condition” erases the PIN number and all settings.

AV1 AV1 AV2

AV2 PC

HDMI

Input Labels

Channel List Editor

9 10 11 12 13 14

:reveal

:hide (skip)

select

reveal / hide

All tuning data will be erased

Auto Tuning

EXIT

RETURN

Start Auto Tuning

Auto Tuning

Scan

120

CH2

EXIT

Fine Tuning

Manual Tuning 1 120 Sound System Colour System

4.5MHz NTSC

Manual Tuning

Select

Enter channel

Store

EXIT Search RETURN

CH Up

CH Down

CH37

Press repeatedly until “Auto Tuning”

appears Access “Auto Tuning” Start “Auto Tuning”

• To return to TV

Auto tuning using the buttons on the TV

Manual Tuning

Channel List Edit Access Auto Tuning

Access

Tuning Menu

You can skip unwanted channels and retune the TV channels when necessary.

Select the function you want to perform

Tuning and Editing Channels

Channel List Edit

Settings are made automatically

Start Auto Tuning

•

All the previous tuning settings are erased.

• When the operation is completed, the channel at channel position “1” will be

displayed.

• Search begins in the order from the lower channels to the higher channels. Channels

received during this process are added to the list (see above).

• If tuning has not been done completely “Manual Tuning” (see right)

Auto Tuning

Fine Tuning

Use to make small adjustments to the tuning of an individual channel (a ected by weather conditions, etc.)

Manual Tuning

Set channel manually a er Auto Tuning.

•

Before performing this function, you need to set the “Sound System” and “Colour System”.

Set Colour System “Auto” normally.

• If a VCR is connected only with the RF cable, select channel position “0”.

Select channel Select channel position

Manual Tuning

VIERA Main Menu

Tuning Menu

Setup

You can hide (skip) unwanted channels.  e hidden channels cannot be displayed except in this function.

Select a channel, then select to reveal or hide

You can set all TV channels automatically.

•

To reveal all channels

•

To retune selected channel (Manual Tuning)

Store

VIERA Link “ Control™”

Enjoy additional HDMI interoperability with Panasonic products which have “HDAVI Control” function.  is TV supports “HDAVI Control 5” function. Connections to the equipment (DIGA Recorder, HD Video Camera, Player theatre, Ampli er, etc.) with HDMI cable allow you to interface them automatically.  ese features are limited to models incorporating “HDAVI Control” and “VIERA Link”.

• Some functions are not available depending on the equipment’s version of HDAVI

Control. Please con rm the connected equipment’s version of HDAVI Control.

• VIERA Link “HDAVI Control”, based on the control functions provided by HDMI

which is an industry standard known as HDMI CEC (Consumer Electronics Control), is a unique function that we have developed and added. As such, its operation with other manufacturers’ equipment that supports HDMI CEC cannot be guaranteed.

• Please refer to individual manuals for the equipment. About applicable Panasonic

equipment, consult your local Panasonic dealer.

: HDMI Connection only : HDMI and Audio out connections : available with the equipment which has “HDAVI Control 2 or later” function : available with the equipment which has “HDAVI Control 4 or later” function : while playingback a disc : except for watching a disc

Connected equipment

with VIERA Link

function

Features

DIGA

Recorder

1

DVD Player / Blu-ray

Disc

Player

1

HD Video

Camera /

LUMIX

Camera

1

Player

theatre

2

Blu-ray

Disc

theatre

2

Ampli er

2

Easy playback

5 5

–

Power on link

–

Power o link

Reduce unnecessary power consumption in standby

4 4

––

4

–

Auto standby for unnecessary equipment

3 3

–

3

Control the menu of the connected equipment by VIERA remote control

3 3 3 3 3

–

Speaker control

–––

Connection

•

For DIGA Recorder / DVD Player / Blu-ray Disc Player / HD Video Camera / LUMIX Camera with VIERA Link function, connect to HDMI terminal via an HDMI cable.

• For Player theatre / Blu-ray Disc theatre / Ampli er, connect to HDMI terminal via an

HDMI cable and/or RCA cable for audio output from the TV.

• Use fully wired HDMI compliant cable. Non-HDMI-compliant cables cannot be utilized.

Recommended Panasonic’s HDMI cable part number:

• RP-CDHS15 (1.5 m) • RP-CDHS30 (3.0 m) • RP-CDHS50 (5.0 m)

Preparations

•

Connect the equipment supporting VIERA Link.

• Set up the connected equipment. Read the manual of the equipment.

• Set VIERA Link On in Setup Menu “VIERA Link” (p. 10)

• Set up the TV A er connection, turn the equipment on and then switch the TV on. Set

the input mode to HDMI (p. 14), and make sure that an image is displayed correctly.  is setup should be done each time when the following conditions occur:

• for the  rst time • when adding or reconnecting equipment • when changing setup

Stereo / Bilingual Sound Selection

Audio Signal STEREO

MAIN

SUB MONO

Mode Indicator

NICAM .......Used in New Zealand, Singapore, Hong Kong etc.

Type of broadcast

Regular broadcast (Standard Audio)

Regular +

NICAM MONO

(MAIN )

NICAM

STEREO

NICAM DUAL

MONO

(MAIN / SUB )

Mode Indicator

Indicator

A2 (German) .......Used in Australia, Malaysia etc.

Type of broadcast

Regular broadcast (Standard Audio)

BILINGUAL or DUAL MONO:

MAIN

/ SUB

STEREO

Mode Indicator

Indicator

• If the stereo signal is poor or the receiving conditions are not optimum or if

STEREO:MONO automatic switching occurs, it is recommended you switch from STEREO to MONO.

• Even when the contents of the receiving signal undergo changes, selection mode is kept

intact.

• When the receiving conditions deteriorate, listening will be easier if the mode is set to the

MONO position, using the Stereo / Bilingual Sound Selection button.

• DUAL, also known as DUAL MONO or as BILINGUAL is not currently transmitted in

some countries.

When you receive the stereo / bilingual sound system, sound output modes can be selected by pressing the Stereo / Bilingual Sound Selection button.

VIERA Link Control

Speaker Selection

Recorder Home Cinema

VIERA Link Menu

VIERA Link Control

Speaker Selection

Recorder Home Cinema

VIERA Link Menu

VIERA Link Control

Speaker Selection

Recorder Home Cinema

VIERA Link Control

You can control some functions of the connected equipment with this TV remote control by pointing at the TV’s signal receiver.

Select “VIERA Link Control”, then select the equipment you want to access

 e menu of the accessed equipment is displayed.  e displayed item may vary depending on the connected equipment. (Input mode will be changed automatically.)

Operate the connected equipment

Follow the operation guide.

†

² “Home Cinema” means Player theatre,

Blu-ray Disc theatre or Recorder theatre.

†3

“Other” means Tuner set top box.

access

select “VIERA Link Control” select the equipment

You can control the theatre speaker with this TV remote control by pointing at the TV’s signal receiver.

Select “Speaker Selection”, then set to “Home Cinema” or “TV”

•

 ese functions may not work properly depending on the connected equipment.

• Image or sound may not be available for the  rst few seconds when input mode is

switched.

• Easy playback may be available by using the remote control for Player theatre, Blu-ray

Disc theatre or Ampli er. Read the manual of the equipment.

• “HDAVI Control 5” is the newest standard (current as of December, 2009) for HDAVI

Control compatible equipment.  is standard is compatible with conventional HDAVI equipment.

• To con rm this TV’s version of HDAVI Control “System Information” (p. 10)

VIERA TOOLS

Directly accesses to some special features.

Display icon of the features

Select a feature, then follow the operation of each feature

VIERA Link Control / Speaker Selection / Slideshow / Photos

Select the function you want to perform

If you cannot operate, check the settings and the equipment

“Summary of features”, “Connection”, “Preparations” (p. 12)

Using VIERA Link Menu

Display “VIERA Link Menu”

VIERA Link Control

Speaker Selection

Recorder Home Cinema

VIERA Link Menu

VIERA Link Control

Speaker Selection

Recorder / Player /

†2

Home Cinema / Video Camera

/ LUMIX / Digital Camera /

†3

Other

To display the operation guide

Store / set / access

Move the cursor / select the menu Return to the previous menu

Move the cursor / access / adjust Exit the menu

When the key words are displayed on colour bar

Type of the connected equipment is displayed.

If you access non-VIERA Link equipment

When the equipment with “HDAVI Control” function is connected

Some operations may not be available depending on the equipment. If so, use its own remote control.

You can access the menu of the equipment but you cannot operate it. Use its own remote control to operate the equipment.

select “Speaker Selection”

set

Home Cinema

Player theatre, Blu-ray Disc theatre or Ampli er in Standby mode will be automatically turned on and the TV sound will be output from the speakers connected to the equipment.

•

Volume up / down Volume slide bar will be displayed when adjusting the volume of

the equipment.

• Mute

•  e sound of TV speakers is mute.

• When the equipment is turned o , TV speakers will be active.

TV speakers are active.

If you wish to enjoy multi-channel sound (e.g. Dolby Digital 5.1ch) via an

Ampli er, connect with HDMI and RCA cable, and then select “Home Cinema”. To enjoy the sound from the DIGA Recorder in multi-channel sound, connect an HDMI cable from the DIGA Recorder to the Ampli er.

You can also access VIERA Link Control

by using VIERA TOOLS (see below).

select access

File name

Date

Pixel

p1010001

1/38

2008/10/23

1600 x 1200

p1010004p1010003p1010002p1010001

p1010008p1010007p1010006p1010005

p1010012p1010011p1010010p1010009

Photo View Mode

Folder view 100_PANA

etaD yb troShtnoM yb troSwohsedilS

Select

EXIT Select RETURN

View

Rotate

Slideshow

Select

Single view

EXIT

List

Folder name

Number of pictures

100_PANA

1/23

38 pictures

200_PANA 20 pictures

102_PANA 14 pictures

101_PANA

3 pictures

100_PANA 38 pictures

Nature

14 pictures

Fruit

18 pictures

ROOM

1 picture

201_PANA

7 pictures

Photo View Mode

Folder view

Select

EXIT Select RETURN

All pictures

View

Side of the TV

Label surface

Push the center of the card until a click is heard (To remove, push again)

select

view

• To display / hide the operation guide

• To return to thumbnail (List)

Start Slideshow

To previous photo Rotate 90° (anti-

clockwise) To next photo Rotate 90° (clockwise)

To view a single photo (Single view)

To sort into folders

( umbnail)

(Folder view)

Transition E ect

Selects the transition e ect for

slideshow (O /Wipe /Wipe /Wipe / Wipe /

Comb / Comb / Dissolve / Checker Wipe / Random / Multi / Collage)

• When you select “Random”, all e ects are performed

randomly except “Multi” and “Collage”.

Colour E ect

Selects the colour e ect for

slideshow (O /Sepia/Gray scale)

Interval

Selects slideshow interval

(Short / Normal / Long)

Repeat

Slideshow repeat (O / On)

• To sort by month

• To sort by date

• To return to unsorted

thumbnail

Viewing Setup

Transition Effect Off

Interval Repeat

Short On

Colour Effect Off

change

select

Error display (unloadable image, etc.)

Information of selected photo

Selected photo

select

select sorted

folder

view

thumbnail

Input Selection

AV1

AV2

PC HDMI TV

select

watch

Watching External Inputs

Display the input selection menu

Select the input mode of the connected equipment to watch

Example (AV2)

You can also select the input using the AV button

on the side panel of the TV (p. 5)

Press the button

repeatedly until the desired input is selected.

You can label or skip each input mode “Input

Labels” (p. 10) Skipped inputs will not be displayed when the AV button is pressed.

NOTE

•

If the external equipment has an aspect adjustment function, set it to “16:9”.

• It is also possible to switch to PC input directly from

TV mode by pressing the PC button.

• You can also listen to the PC sound by connecting an

audio cable.

• You can set up some functions; Advanced PC Settings

(p. 8) in Picture Menu and PC Setup (p. 9) in Setup Menu.

• For HDMI-compatible PC, it is possible to connect to

HDMI terminal by using HDMI cable.

Viewing from SD Card (VIERA IMAGE VIEWER)

Photo View: View still pictures recorded on a digital camera.

• During the operation, no signals are output from any of

the AV terminals.

• “Date” shows the date on which the recording was made

by the digital camera. It is shown with asterisks when the  le has no record of the date.

•  e  les which are not in a folder will be collected

to the folder named “/”.

• To display all the photos

Enter SD mode (Photo View)

Select the folder you want to view

All photos in SD Card are displayed by thumbnail.

Insert the SD card

Select a photo

VIERA Main Menu Viewing Setup

Slideshow settings

To start Slideshow within the thumbnail

• To pause cursor up button (press again to resume)

• To return to Single view

Select an item and change the setting

Message Meaning / Action

Cannot read  le  e  le is broken or unreadable.

 e TV does not support the format.

No SD card inserted Con rm SD Card is inserted correctly.

No valid  le to play  e card has no data.

Over 9999 pictures found (max. is 9999)

Maximum valid number of photos is 9,999.

SD card on screen messages

NOTE

•

Signals other than above may not be displayed properly.

•  e above signals are reformatted for

optimal viewing on your display.

• PC signal is magni ed or compressed

for display, so that it may not be possible to show  ne detail with su cient clarity.

FAQ s

Before requesting service or assistance, please follow these simple guides to resolve the problem. If problem still persists, please contact your local Panasonic dealer.

White spots or shadow images (noise)

• Check the position, direction, and connection of the aerial.

Neither image nor sound is produced

• Is the TV in “AV mode”?

• Is the mains lead plugged into the socket outlet?

• Is the TV turned On?

• Check “Picture Menu” and volume.

• Check all required cables and connections are

 rmly in place.

An error message appears

• Follow the message’s instructions.

• If the problem persists, contact your local

Panasonic dealer.

 ere may be red spots, blue spots, green spots and black spots on the screen

•  is is a characteristic of liquid crystal panels and is not a problem.  e liquid crystal panel is built with very high precision technology giving you  ne picture details. Occasionally, a few nonactive pixels may appear on the screen as a  xed point of red, green, blue or black. Please note this does not a ect the performance of your LCD and it is not a quality problem.

“VIERA Link” function does not work and an error message appears

• Con rm the connection.

• Turn the connected equipment on and then

switch the TV on.

 e LCD panel moves slightly when it is pushed with a  nger Clattered sound might be heard

•  ere are some looseness around the panel to prevent damage to the panel.  e panel might move slightly when it is pushed with a  nger, and clattered sound might be heard.  is is not a malfunction.

TV goes into “Standby mode”

• Auto power standby function is activated.

•  e TV enters Standby mode about 30 minutes

a er broadcasting ends.

No sound is produced

• Is “Sound Mute” active?

• Is the volume set to the minimum?

 e remote control does not work or is intermittent

• Are the batteries installed correctly?

• Has the TV been switched On?

• Point the remote control directly at the front of

the TV (within a 30 degree angle of the front of the TV).

• Situate the TV away from sunshine or other sources of bright light not to shine on the TV’s remote control signal receiver.

Sound is unusual

• Set the sound setting of the connected equipment to “2ch L.PCM”.

• Check the “HDMI Input” setting in the Sound Menu.

• If digital sound connection has a problem, select analogue sound connection.

Sound level is low or sound is distorted

• Sound signal reception may be deteriorated.

• Set “MPX” in the Sound Menu to “Mono”.

Pictures from external equipment are unusual when the equipment is connected via HDMI

• Is the HDMI cable connected properly?

• Turn O the TV and equipment, then turn them

On again.

• Check an input signal from the equipment.

• Use an equipment compliant with

EIA/CEA-861/861B.

No image can be displayed

• Is “Colour” or “Contrast” in the Picture Menu set to the minimum?

Blurry or distorted image

(no sound or low volume)

• Reset channel.

Chaotic image, noisy

• Change the setting of “P-NR” in the Picture Menu (to remove noise).

• Check nearby electrical products (car, motorcycle,  uorescent lamp).

Unusual image is displayed

• Tu rn o the TV with Mains power On / O switch, then turn it on again.

Input signals that can be displayed

Input Signal name COMPONENT HDMI

COMPONENT (Y, PB/CB, PR/CR), HDMI

 Mark: Applicable input signal

525 (480) / 60i



525 (480) / 60p



625 (576) / 50i



625 (576) / 50p



750 (720) / 60p



750 (720) / 50p



1,125 (1,080) / 60i



1,125 (1,080) / 50i



1,125 (1,080) / 60p



1,125 (1,080) / 50p



1,125 (1,080) / 24p



Input Signal name

Horizontal

frequency

(kHz)

Vertical

frequency

(Hz)

PC (from D-sub 15P)

Applicable input signal for PC is basically compatible to VESA standard timing.

640 × 400 @70 Hz 31.47 70.07 640 × 480 @60 Hz 31.47 59.94 640 × 480 @75 Hz 37.50 75.00 800 × 600 @60 Hz 37.88 60.32 800 × 600 @75 Hz 46.88 75.00 800 × 600 @85 Hz 53.67 85.06 852 × 480 @60 Hz 31.44 59.89 1,024 × 768 @60 Hz 48.36 60.00 1,024 × 768 @70 Hz 56.48 70.07 1,024 × 768 @75 Hz 60.02 75.03 1,024 × 768 @85 Hz 68.68 85.00 1,280 × 1,024 @60 Hz 63.98 60.02 1,280 × 768 @60 Hz 47.70 60.00 1,366 × 768 @60 Hz 48.39 60.04 Macintosh13” (640 × 480) 35.00 66.67 Macintosh16” (832 × 624) 49.73 74.55 Macintosh21” (1,152 × 870) 68.68 75.06

PC (from HDMI terminal)

Applicable input signal for PC is basically compatible to HDMI standard timing

640 × 480 @60 Hz 31.47 60.00

750 (720) / 60p 45.00 60.00

1,125 (1,080) / 60p 67.50 60.00

Hot Plug Detect 19 DDC/CEC Ground 17 SCL 15 CEC 13 TMDS Clock Shield

11 TMDS Data0− 9 TMDS Data0+ 7 TMDS Data1 Shield 5 TMDS Data2− 3 TMDS Data2+ 1

18 +5V Power

16 SDA 14 Reserved

(in cable but

N.C. on device) 12 TMDS Clock− 10 TMDS Clock+ 8 TMDS Data0 Shield 6 TMDS Data1− 4 TMDS Data1+ 2 TMDS Data2 Shield

HDMI terminal

A2 Landscape - en.indd 2A2 Landscape - en.indd 2 5/25/2010 3:29:18 PM5/25/2010 3:29:18 PM