Panasonic KX-MB772CX, KX-MB262CX User Manual
Operating Instructions
Multi-Function Printer
Model No. KX-MB262CX
This pictured model is KX-MB262.
KX-MB772CX
Do NOT connect the USB cable until prompted by the Multi-Function Station (CD-ROM).
12
KX-MB262CX or KX-MB772CX may not be available in some areas.
KX-MB772 only:
L This unit is compatible with Caller ID. To use this feature, you must subscribe to the
appropriate service of your service provider.
L Be sure to use the telephone line cord included in this unit.
L This model is designed to be used in Middle East, Hong Kong, Malaysia, Asia, New Zealand,
Africa and Latin America according to the location setting feature. The default setting is
Middle East. To change the location setting, see page 54 (feature #114).
Thank you for purchasing a Panasonic MultiFunction Printer.
This model is designed to be used in Middle East,
Hong Kong, Malaysia, Asia, New Zealand, Africa and
Latin America according to the location setting
feature (KX-MB772 only).
The default setting is Middle East. To change the
location setting, see page 54 (feature #114).
Note:
L The suffix in the model number will be omitted in
these instructions.
L Most figures shown in these operating instructions
are based on a KX-MB262.
Trademarks:
L Microsoft, Windows, Windows Vista and PowerPoint
are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or
other countries.
L Pentium is a registered trademark or trademark of
Intel Corporation in the United States and/or other
countries.
L Screen shots reprinted with permission from
Microsoft Corporation.
L Adobe and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
L Avery is a registered trademark of Avery Dennison
Corporation.
L XEROX is a registered trademark of Xerox
Corporation.
L All other trademarks identified herein are the
property of their respective owners.
Copyright:
L This material is copyrighted by Panasonic
Communications Co., Ltd., and may be reproduced
for internal use only. All other reproduction, in whole
or in part, is prohibited without the written consent of
Panasonic Communications Co., Ltd.
© 2007 Panasonic Communications Co., Ltd. All Rights
Reserved.
2
LocationLocation
Available features by location setting (KX-MB772 only)
The following features may vary slightly depending on the location setting (#114 on page 54).
Change the location setting to match where you use the unit.
Location
Feature/Code Middle
East,
Africa,
Latin
America
Dialling mode
{#}{1}{2}{0}
TEL/FAX ring count
{#}{2}{1}{2}
Manual answer mode
{#}{4}{0}{4}
Distinctive Ring
{#}{4}{3}{0}
Fax ring pattern
(Distinctive Ring
feature)
{#}{4}{3}{1}
Silent fax ring count
{#}{4}{3}{6}
rrrr – page 18
rrrr – page 57
rrrr – page 57
rr – rrpage 51
r ––r – page 52
rrrr – page 59
Hong
Kong
Malaysia Asia New
Zealand
Page
3
Important Information
Important InformationImportant Information
For best performance
Toner cartridge and drum unit
L When replacing the toner cartridge or drum unit, do
not allow dust, water, or liquids to come in contact
with the drum. This may affect print quality.
L For optimal performance, genuine Panasonic toner
cartridges and drum units are recommended. We
cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
unit:
– Damage to the unit
– Poor print quality
– Improper operation
Toner cartridge
L Do not leave the toner cartridge out of the protection
bag for a long time. It will decrease the toner life.
Drum unit
L Read the instructions on page 10 before you begin
installation of the drum unit. After you have read
them, open the drum unit protection bag. The drum
unit contains a photosensitive drum. Exposing it to
light may damage the drum. Once you have opened
the protection bag:
– Do not expose the drum unit to light for more than
5 minutes.
– Do not touch or scratch the black drum surface.
– Do not place the drum unit near dust or dirt, or in
a high humidity area.
– Do not expose the drum unit to direct sunlight.
L To extend the life of the drum unit, the unit should
never be turned OFF immediately after printing.
Leave the power turned ON for a minimum of 30
minutes after printing.
Location
L To avoid malfunction, do not position the unit near
appliances such as TVs or speakers which generate
an intense magnetic field.
Static electricity
L To prevent static electricity damage to the interface
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
Environment
L Keep the unit away from electrical noise generating
devices, such as fluorescent lamps and motors.
L The unit should be kept free from dust, high
temperature and vibration.
L The unit should not be exposed to direct sunlight.
L Do not place heavy objects on top of the unit. When
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
L The unit should be kept away from heat sources such
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
L In the printing process, heat is used to fuse toner
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
L Do not place any objects within 10 cm of the right, left
and back sides of the unit.
L Do not cover slots or openings on the unit. Inspect
the air circulation vents regularly and remove any
dust build-up with a vacuum cleaner (1).
1
1
Routine care
L Wipe the outer surface of the unit with a soft cloth. Do
not use benzine, thinner, or any abrasive powder.
4
Table of Contents
1. Table of Contents
1. Introduction and Installation
Accessories
1.1 Included accessories..................................... 7
1.2 Accessory information ................................... 7
Finding the Controls
1.3 Button descriptions........................................ 8
1.4 Overview ....................................................... 9
Installation
1.5 Toner cartridge and drum unit ..................... 10
1.6 Output tray................................................... 13
1.7 Recording paper.......................................... 15
2. Preparation
Connections and Setup
2.1 Connections ................................................ 17
2.2 Dialling mode (KX-MB772 only) ................. 18
2.3 Selecting the operation mode (Scan/Copy)
(Fax: KX-MB772 only) ................................. 18
Document Requirements
2.4 Setting the original....................................... 19
Help
2.5 Help function (KX-MB772 only) ................... 20
Vo lu m e
2.6 Adjusting volume (KX-MB772 only)............. 21
Initial Programming
2.7 Date and time (KX-MB772 only).................. 21
2.8 Your logo (KX-MB772 only) ......................... 22
2.9 Your fax number (KX-MB772 only) .............. 22
2.10 Installing Multi-Function Station .................. 23
2.11 Starting Multi-Function Station .................... 25
3. Printer
Printer
3.1 Printing from Windows applications ............ 26
4. Scanner
Scanner
4.1 Scanning from the unit (Push Scan)............ 28
4.2 Scanning from a computer (Pull Scan)........ 29
5. Copier
Copy
5.1 Making a copy ............................................. 31
5.2 More copying features................................. 32
6. Fax (KX-MB772 only)
Sending Faxes
6.1 Sending a fax manually............................... 36
6.2 Storing items for the one-touch dial feature and
navigator directory....................................... 37
6.3 Sending a fax using one-touch dial feature and
navigator directory....................................... 38
6.4 Broadcast transmission ............................... 39
6.5 Sending a computer document as a fax
message from your computer...................... 41
Receiving Faxes
6.6 Selecting the way to use your fax machine..41
6.7 Receiving a fax automatically – Auto answer
ON................................................................43
6.8 Receiving a fax manually – Auto answer OFF
.....................................................................43
6.9 Using the unit with an answering machine...45
6.10 Receive polling (retrieving a fax placed on
another fax machine) ...................................45
6.11 Junk fax prohibitor (preventing fax reception
from undesired callers).................................46
6.12 Receiving a fax into your computer..............47
7. Caller ID (KX-MB772 only)
Caller ID
7.1 Caller ID service...........................................48
7.2 Viewing and calling back using caller
information ...................................................49
7.3 Editing a caller’s telephone number before
calling back/storing.......................................49
7.4 Erasing caller information.............................50
7.5 Storing caller information .............................50
8. Distinctive Ring (KX-MB772 only)
Distinctive Ring
8.1 Distinctive Ring (Fax Ability/Duplex ring)
service..........................................................51
8.2 Using two or more phone numbers on a single
telephone line...............................................51
8.3 Using three or more phone numbers on a
single telephone line ....................................51
8.4 Programming the ring pattern assigned for fax
.....................................................................52
9. Programmable Features
Features Summary
9.1 Programming................................................53
9.2 Basic features ..............................................54
9.3 Fax features (KX-MB772 only) .....................57
9.4 Copy features...............................................61
9.5 PC print features ..........................................61
9.6 Scan features...............................................62
10.Useful Information
Useful Information
10.1 Character entry (KX-MB772 only) ................63
10.2 Status of the unit ..........................................64
10.3 Cancelling the operations.............................64
11.Help
Error Messages
11.1 Error messages – Reports (KX-MB772 only)
.....................................................................65
11.2 Error messages – Display ............................66
5
Table of Contents
Troubleshooting
11.3 When a function does not work ................... 68
12.Paper Jams
Jams
12.1 Recording paper jam ................................... 73
12.2 Document jams (Auto document feeder) (KX-
MB772 only) ................................................ 78
13.Cleaning
Cleaning
13.1 Cleaning the white plates and glass............ 79
13.2 Cleaning the document feeder rollers (KX-
MB772 only) ................................................ 82
14.General Information
Printed Reports
14.1 Reference lists and reports ......................... 83
Specifications
14.2 Specifications .............................................. 83
15.Index
15.1 Index........................................................... 86
6
1Introduction and InstallationAccessories
1. Introduction and Installation
1.1 Included accessories
1 Power cord
(Use the appropriate
power cord for where
you use the unit.)
KX-MB772 only 2 CD-ROM
3 Drum unit 4 Starter toner
cartridge
*1
1.2 Accessory information
To ensure that the unit operates properly, we
recommend the use of a Panasonic toner cartridge and
drum unit. See page 85 for specifications.
1.2.1 Available accessories
– Replacement toner cartridge
L Model No. (Part No.): KX-FAT92A/KX-FAT92E
– Replacement drum unit
L Model No. (Part No.): KX-FAD93A/KX-FAD93E
*1 Approx. 2,000 sheets of A4 size paper can be
printed with KX-FAT92A/KX-FAT92E.
L We cannot be responsible for any damage to the unit
or degradation of print quality which may occur from
the use of a non-Panasonic toner cartridge and drum
unit.
*1
5 Quick reference guide 6 Quick installation guide
7 KX-MB772 only
Telephone line cord
(Use the appropriate
telephone line cord for
where you use the
unit.)
*1 Prints about 500 A4-sized pages with a 5 % image
area (page 85).
Note:
L Save the original carton and packing materials for
future shipping and transportation of the unit.
7
1. Introduction and Installation
Finding the Controls
1.3 Button descriptions
LABCDEFG HIJK
MN
* The small hole on the left side of the LCD display is for
beeps (KX-MB262 only).
* The pictured model is KX-MB772.
A {COPY}
L To switch to the copy mode (page 18, 31).
B {SCAN}
L To switch to the scan mode (page 18, 28).
C {COLLATE}
L To make a collated copy (page 35).
{DIRECTORY} (KX-MB772 only)
L To initiate the navigator directory (page 38, 39).
D {CONTRAST}
L To select a contrast (page 31, 36).
E {RESOLUTION}
L To select a resolution (page 31, 36).
F {ZOOM}
L To enlarge or reduce a document when copying
(page 32).
{QUICK SCAN} (KX-MB772 only)
L To store a scanned document into memory, and
then send it (page 37).
G {PAGE LAYOUT}
L To make quick ID, poster or N in 1 copy (page 33).
H {SET}
L To store a setting during programming.
I {MENU}
L To start or exit programming.
J {CALLER ID} (KX-MB772 only)
L To use Caller ID features (page 49).
L To change the display of the caller information
(page 49).
K {REDIAL}{PAUS E} (KX-MB772 only)
L To redial the last number dialled. If the line is busy
when you send a fax, the unit will automatically
redial the number 2 or more times.
L To insert a pause during dialling.
L {STOP}
L To stop an operation or programming session.
L To erase a character/number.
M {FAX AUTO ANSWER} (KX-MB772 only)
L To turn the auto answer setting ON/OFF (page
43).
{POWER SAVE} (KX-MB262 only)
QRPOSTUV
L To set the unit to the power save mode manually.
N {FAX} (KX-MB772 only)
L To switch to the fax mode (page 18, 36).
O {BROADCAST} (KX-MB772 only)
L To send a document to multiple parties (page 39).
P {MANUAL BROAD} (KX-MB772 only)
L To send a document to multiple parties manually
(page 39).
Q Station keys (KX-MB772 only)
L To use the one-touch dial feature (page 37, 38).
R Navigator key
L To select desired settings during scanning or
copying (page 28, 31).
L To adjust volume (KX-MB772 only) (page 21).
L To search for a stored item (KX-MB772 only)
(page 38).
S {LOWER} (KX-MB772 only)
L To select stations 4–6 for the one-touch dial
feature (page 37, 38).
T {MONITOR} (KX-MB772 only)
L To initiate dialling.
When you press {MONITOR} while receiving a
call, you will be able to hear the other party, but
the other party will not be able to hear you.
U {FLASH} (KX-MB772 only)
L To access special telephone services or for
transferring extension calls.
V {START}
L To copy a document (page 31).
L To scan a document (page 28).
L To send or receive a fax (KX-MB772 only) (page
36).
8
1. Introduction and Installation
1.4 Overview
1.4.1 Front view
KX-MB772
12 43
6879j5
KX-MB262
14
1.4.2 Rear view
KX-MB772
A
CD
KX-MB262
A
B
E GF
6895
1 To p cover
2 ADF (Auto Document Feeder) cover
3 Document guides
4 Document cover
5 Output tray
6 Top cover release lever
7 Document entrance
8 Paper input tray
9 Recording paper exit
j Document exit
CD
A Recording paper guides
B Speaker (KX-MB772 only)
C Power inlet
D Manual input tray (Rear cover)
E External telephone jack
F Telephone line jack (KX-MB772 only)
G USB interface connector
G
9
1. Introduction and Installation
Removing the shipping tape
Remove the shipping tape (1).
1
Note:
L Shipping tape positions are subject to change
without notice.
Installation
1.5 Toner cartridge and drum unit
The included toner cartridge is a starter toner cartridge.
Caution:
L Read the following instructions before you begin
installation. After you have read them, open the
drum unit protection bag. The drum unit contains
a photosensitive drum. Exposing it to light may
damage the drum. Once you have opened the
protection bag:
– Do not expose the drum unit to light for more
than 5 minutes.
– Do not touch or scratch the black drum
surface.
– Do not place the drum unit near dust or dirt,
or in a high humidity area.
– Do not expose the drum unit to direct
sunlight.
L We cannot be responsible for any damage to the
unit or degradation of print quality which may
occur from the use of a non-Panasonic toner
cartridge and drum unit.
L Do not leave the toner cartridge out of the
protection bag for a long time. It will decrease the
toner life.
L Do not add toner to the toner cartridge.
1 Before opening the protection bag of the new toner
cartridge, shake it vertically more than 5 times.
10
2 Remove the toner cartridge and drum unit from the
protection bags. Peel off the seal (1) from the toner
cartridge.
L Do not touch or scratch the black drum surface
(2).
1
2
1. Introduction and Installation
3 Place the toner cartridge (3) into the drum unit (4)
vertically.
3
4
4 Turn the green levers (5) on each side of the toner
cartridge while pressing down firmly.
5
6 Lift the top cover release lever (7) and open the top
cover (8).
8
9
7
Note:
L Do not touch the transfer roller (9).
L If the lower glass (j) is dirty, clean it with a soft
and dry cloth.
5 Make sure that the triangles (6) match, to install the
toner cartridge correctly.
6
j
11
1. Introduction and Installation
7 Install the drum and toner unit (k) by holding the
tabs.
k
L Make sure that the triangles (l) match, to install
the drum and toner unit correctly.
8 Close the top cover until locked.
Caution:
L To prevent injuries, be careful not to put your
hands under the top cover.
12
To replace the toner cartridge and the drum unit
When the display shows the following, replace the toner
cartridge.
TONER LOW
l
TONER EMPTY
L To check the drum life and quality, please print the
printer test list (page 83) and refer to page 85 for
information on the drum life. If printing quality is still
poor or “REPLACE DRUM” appears on the display,
replace the toner cartridge and drum unit.
L To ensure that the unit operates properly, we
recommend the use of Panasonic toner cartridge
(Model No. KX-FAT92A/KX-FAT92E) and drum
unit (Model No. KX-FAD93A/KX-FAD93E). See
page 7 for accessory information.
L To maintain print quality and machine life, we
recommend you to clean slots and openings (page 4)
and the inside of the unit (page 79, 82) when
replacing the toner cartridge and/or drum unit.
Waste disposal method
Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.
Toner save feature
If you want to reduce toner consumption, set the toner
save setting to ON (feature #482 on page 56). The toner
cartridge will last approximately 40 % longer. This
feature may lower the print quality.
1. Introduction and Installation
1.6 Output tray
Pull the output tray extender (1) forward gently until it
clicks into place, then press the centre part of the
extender (2) to open.
1
2
Note:
L Do not place the unit in an area where the output tray
may be easily bumped into.
L The output tray can hold up to approximately 150
sheets of printed paper. Remove the printed paper
before the output tray becomes full.
13
1. Introduction and Installation
If the top part of the extender is detached
1. With the top part of the extender in the open position,
insert the tab (1) into the left hole (2) of the
extender.
2
1
2. Slide the other tab (3) into the right hole (4) of the
extender from below until it clicks into place.
If the extender is detached
1. Line up the extender (1) with the left side of the
output tray. Make sure that the triangles (2) match,
to attach the extender correctly.
1
2
2. Snap the extender (3) into the unit by pushing down
the right side of the extender.
14
3
4
3
1.7 Recording paper
The paper input tray unit can hold:
– Up to 250 sheets of 60 g/m
– Up to 230 sheets of 80 g/m
– Up to 200 sheets of 90 g/m2 paper.
L Please refer to page 84 for information on recording
paper.
L The unit is set for printing A4 size paper by
default. If you want to use letter or legal size
paper, change the setting (feature #380 on page
55).
1 Pull the paper input tray (1) until it clicks into place,
then pull it completely out, lifting the front part of the
tray.
1
2
to 75 g/m2 paper.
2
paper.
1. Introduction and Installation
3 Load the paper, print-side up (2).
Important:
L Push and lock the plate (3) in the paper input
tray, if it is lifted.
2
3
4 Adjust the recording paper guides. Pinch the front
side of the recording paper guide (4), then slide it to
match the paper size mark. Pinch the right side of
the recording paper guide (5), then slide it to adjust
the width to the size of the recording paper.
L Make sure that the recording paper is under the
paper limit mark (6), and the paper should not
be loaded over the snubbers (7).
2 Before loading a stack of paper, fan the paper to
prevent paper jams.
6
5
7
4
15
1. Introduction and Installation
5 Insert the paper input tray to the unit, lifting the front
part of the tray. Then push it completely into the unit.
Note:
L If the paper is not loaded correctly, re-adjust the
paper guides, or the paper may jam.
L If the paper input tray does not close, the plate in the
paper input tray may be lifted. Push the paper and
make sure that the paper is laid flat in the paper input
tray.
Caution for the paper input tray
L Do not drop the paper input tray.
L Hold the paper input tray with both hands when
removing or installing. The paper input tray
weighs approximately 2 kg when the recording
paper is fully installed.
16
Approx. 2 kg
2. Preparation
2PreparationConnections and Setup
2.1 Connections
Caution:
L When you operate this product, the power outlet
should be near the product and easily
accessible.
L Be sure to use the telephone line cord included in
this unit (KX-MB772 only).
L Do not extend the telephone line cord (KX-MB772
only).
1 Power cord
L Connect to a power outlet
(220–240 V, 50/60 Hz).
2 Telephone line cord
L Connect to a single telephone line jack.
3 [EXT] jack
*1
L You can connect an answering machine or an
extension telephone. Remove the stopper if
attached.
4 Answering machine (not included)
*1
*1
L If you use the unit with a computer and your internet
provider instructs you to install a filter (5), please
connect it as follows (KX-MB772 only).
5
* The pictured model is KX-MB772.
L A telephone handset cannot be connected directly to
this unit. To talk to the other party, please connect an
extension telephone (KX-MB772 only).
This model is designed to be used in Middle East,
Hong Kong, Malaysia, Asia, New Zealand, Africa
and Latin America according to the location
setting feature (KX-MB772 only).
The default setting is Middle East. To change the
location setting, see page 54 (feature #114).
3
1
2
*2
4
*2
* The pictured model is KX-MB772.
*1 KX-MB772 only
*2 The power cord or telephone line cord may differ
slightly. Use the appropriate power cord or telephone
line cord for where you use the unit.
Important notice for the USB connection
L Do NOT connect the USB cable until prompted by
the Multi-Function Station (page 23).
Note:
L If any other device is connected to the same
telephone line, this unit may disturb the network
condition of the device (KX-MB772 only).
17
2. Preparation
2.2 Dialling mode (KX-MB772
only)
Important:
L Not available when “NEW ZEALAND” is selected in
feature #114 on page 54.
If you cannot dial (page 36), change this setting
according to your telephone line service.
{MENU}
{SET}
1 {MENU} i {#}{1}{2}{0}
DIALLING MODE
=TONE [V^]
2 Press {1} or {2} to select the desired setting.
{1} “PULSE”: For rotary/pulse dial service.
{2} “TONE” (default): For tone dial service.
3 {SET}
4 Press {MENU} to exit.
2.3 Selecting the operation mode
(Scan/Copy) (Fax: KX-MB772
only)
You can select the desired mode by pressing one of the
following buttons.
* The pictured model is KX-MB772.
– {SCAN}: Select this mode when using the unit as a
scanner for the computer (page 28).
– {COPY}: Select this mode when using the unit as a
copier (page 31).
– {FAX } (KX-MB772 only): Select this mode when
using the unit as a fax machine (page 36).
Note:
L The default operation mode is the copy mode.
L You can change the default operation mode (feature
#463 on page 55) and the timer before returning to
the default operation mode (feature #464 on page
56) (KX-MB772 only).
18
Document Requirements
2.4 Setting the original
2. Preparation
2.4.2 Using the auto document feeder (KXMB772 only)
2.4.1 Using the scanner glass
1
2
Open the document cover (1).
1
2 Place the document FACE DOWN on the scanner
glass (2), aligning the top left of the document with
the corner to which the m mark points.
3 Close the document cover.
Note:
L Confirm that there are no documents in the auto
document feeder (KX-MB772 only).
L Place the original onto the scanner glass gently and
do not press down too firmly to avoid malfunction.
L If the original is a thick book, do not close the
document cover.
L Check that ink, paste or correction fluid has dried
completely.
L Effective scanning area is as follows:
Effective scanning area
L Shaded area will be scanned.
4 mm
208 mm
4 mm
mm
5 mm
287
5 mm
1
1
Insert the document (up to 20 pages) FACE UP into
the feeder until a single beep is heard.
2 Adjust the width of the document guides (1) to fit
the actual size of the document.
Note:
L Confirm that there are no documents on the scanner
glass.
L Check that ink, paste or correction fluid has dried
completely.
L Remove clips, staples or other fasteners.
L Do not set the following types of documents: (Make a
copy of the document using the scanner glass and
set the copy instead.)
– Chemically treated paper such as carbon or
carbonless duplicating paper
– Electrostatically charged paper
– Badly curled, creased or torn paper
– Paper with a coated surface
– Paper with printing on the opposite side that can
be seen through the other side, such as
newsprint
L The total height of the documents when laid flat,
must be less than 4 mm. If the documents exceed the
capacity of the auto document feeder, they may fall or
cause a jam in the feeder (KX-MB772 only).
L To set a document with a width of less than 210 mm,
we recommend using the scanner glass to copy the
original document onto A4 or letter-sized paper, then
setting the copied document (KX-MB772 only).
L Do not set documents that do not satisfy the
requirements of size and weight. Make a copy of the
document using the scanner glass and set the copy
(KX-MB772 only).
L Available document size, document weight and
effective scanning area are as follows:
19
2. Preparation
Minimum document size
128 mm
Maximum document size
216 mm
Effective scanning area
L Shaded area will be scanned.
128 mm
600 mm
5 mm
5 mm
Help
2.5 Help function (KX-MB772
only)
The unit contains helpful information on the following
topics which can be printed for reference purposes, as
follows:
– “BASIC SETTINGS”
– “FEATURE LIST”
– “DIRECTORY”
– “FAX RECEIVING”
– “COPIER”
– “REPORTS”
– “CALLER ID”
{MENU}
{SET}{<}{>}
1 Press {MENU} repeatedly to display “HELP”.
2 Press {<} or {>} repeatedly to display the desired
item. i {SET}
3 Press {MENU} to exit.
4 mm 4 mm
208 mm
216 mm
Document weight
L Single sheet:
L Multiple sheets:
2
60 g/m
60 g/m2 to 75 g/m
to 75 g/m
2
2
20
2. Preparation
Volume
2.6 Adjusting volume (KX-MB772
only)
Important:
L Before adjusting volume, set the operation mode
to fax mode. If the {FAX} light is OFF, turn it ON
by pressing {FAX}.
{FAX}
Ringer volume
While the unit is idle, press {V} or {^}.
L If there are any documents in the document
entrance, you cannot adjust the volume. Confirm that
there are no documents in the entrance.
To turn the ringer OFF
Press {V} repeatedly to display “RINGER OFF= OK?”.
i {SET}
L The unit will not ring.
L To turn the ringer back ON, press {^}.
Ringer pattern
L You can select one of 3 ringer patterns (feature #161
on page 55).
Monitor volume
While using the monitor, press {V} or {^}.
{V}{^}{SET}
Initial Programming
2.7 Date and time (KX-MB772
only)
{MENU}
{<}{>}{SET}{FAX}
1 {MENU} i {#}{1}{0}{1} i {SET}
D:|01/M:01/Y:07
TIME: 00:00
2 Enter the current date/month/year/hour/minute by
selecting 2 digits for each. Press {*} repeatedly to
select “AM” or “PM”, or 24-hour time entry.
Example: 10 August, 2007 10:15 PM (12 hour
clock format)
1. Press {1}{0} {0}{8} {0}{7} {1}{0} {1}{5}.
D:|10/M:08/Y:07
TIME: 10:15
2. Press {*} repeatedly to select “PM”.
3 {SET}
4 Press {MENU} to exit.
Note:
L The other party’s fax machine will print the date and
time on the top of each page you send according to
your unit’s date and time setting.
L After setting the date and time, if the unit is in the
copy mode, change it to the fax mode by pressing
{FAX}. You can check your unit’s date and time
setting on the display.
To correct a mistake
Press {<} or {>} to move the cursor to the incorrect
number, and make the correction.
If you have subscribed to a Caller ID service
If feature #114 is set to “NEW ZEALAND”, the date and
time will be automatically set according to the received
caller information.
L If the time has not previously been set, Caller ID will
not adjust the clock.
21
2. Preparation
2.8 Your logo (KX-MB772 only)
You can program your logo (name, company name, etc.)
so that it appears on the top of each page sent.
{MENU} {STOP}
{SET}
{<}{>}
1 {MENU} i {#}{1}{0}{2} i {SET}
LOGO=|
2 Enter your logo, up to 30 characters (see page 63 for
character entry). i {SET}
3 Press {MENU} to exit.
To correct a mistake
Press {<} or {>} to move the cursor to the incorrect
character, and make the correction.
L To erase all characters, press and hold {STOP}.
2.9 Your fax number (KX-MB772
only)
You can program your fax number so that it appears on
the top of each page sent.
{MENU} {STOP}
{SET} {FLASH}
{<}{>}
1 {MENU} i {#}{1}{0}{3} i {SET}
NO.=|
2 Enter your fax number, up to 20 digits.
L To enter a “+”, press {*}.
L To enter a space, press {#}.
Example: +64 9 1234567
Press {*}{6}{4}{#}{9}{#}{1}{2}{3}
{4}{5}{6}{7}.
L To enter a hyphen, press {FLASH}.
L To erase a number, press {STOP}.
3 {SET}
4 Press {MENU} to exit.
To correct a mistake
Press {<} or {>} to move the cursor to the incorrect
number, and make the correction.
L To erase all numbers, press and hold {STOP}.
22
2.10 Installing Multi-Function
Station
2.10.1 Required computer environment
Panasonic Multi-Function Station software enables the
unit to carry out the following functions:
– Printing on plain paper and labels
– Scanning documents and converting an image into
text with Readiris OCR software
– Scanning from other applications for Microsoft
Windows® that support TWAIN scanning
– Storing, editing or erasing items in directories using
your computer (KX-MB772 only)
– Programming the features using your computer
– Sending, receiving fax documents using your
computer (KX-MB772 only)
To use Multi-Function Station on your computer, the
following are required:
Operating System:
Windows 98/Windows Me/Windows 2000/Windows
XP/Windows Vista™ operating system
CPU:
Windows 98: Pentium
Windows Me: Pentium 150 MHz or faster
Windows 2000: Pentium 166 MHz or faster
Windows XP: Pentium 300 MHz or faster
Windows Vista: Recent Processor (x86) 800 MHz or
higher processor
RAM:
Windows 98: 24 MB (32 MB or more recommended)
Windows Me: 32 MB (64 MB or more recommended)
Windows 2000: 64 MB or more
Windows XP: 128 MB or more
Windows Vista: 512 MB or more
Other Hardware:
CD-ROM drive
Hard disk drive with at least 150 MB of available space
USB interface
Warning:
L To assure continued emission limit compliance, use
only shielded USB cable.
Note:
L Be sure to use a Hi-Speed USB 2.0 certified cable if
your computer is equipped with the Hi-Speed USB
2.0 interface.
L USB cable is not included. Please purchase a
shielded Type-A male/Type-B male USB cable.
®
90 MHz or faster
®
2. Preparation
dialogue box will appear. Click [Cancel] to close
it.
L The screenshots shown in these instructions are
for Windows XP and are included for reference
only.
L The screenshots shown in these instructions
may differ slightly from those of the actual
product.
L Software features and appearance are subject to
change without notice.
1 Start Windows and exit all other applications.
L For Windows 2000, Windows XP and Windows
Vista users, you must be logged in as an
administrator in order to install Multi-Function
Station.
2 Insert the included CD-ROM into your CD-ROM
drive.
L If the [Select Language] dialogue box appears,
select the desired language that you want to use
with this software. Click [OK].
L If the installation does not start automatically:
Click [Start]. Choose [Run...]. Type “D:\Install”
(where “D:” is the drive letter of your CD-ROM
drive). Click [OK].
(If you are not sure what the drive letter is for your
CD-ROM drive, use Windows Explorer and look
for the CD-ROM drive.)
3 [Easy installation]
L The installation will start.
4 When the setup program starts, follow the on-screen
instructions.
L Readiris OCR software (page 28) and Device
Monitor (page 64) will also be installed.
5 When the [Connect Type] dialogue box appears,
select [Connect directly with a USB cable.]. i
[Next]
L The [Connect Device] dialogue box will appear.
6 Connect the unit with the USB cable (1), then click
[Next].
2.10.2 Installing Multi-Function Station on
a computer
L Install Multi-Function Station (CD-ROM) before
connecting the unit to a computer with USB
cable. If the unit is connected to a computer with
USB cable before installing Multi-Function
Station, the [Found New Hardware Wizard]
1
* The pictured model is KX-MB772.
23
2. Preparation
L If the unit is connected to your computer, the
model name will be automatically detected.
L You can change the name of the unit if
necessary.
7 Click [Install], then follow the on-screen
instructions.
L The files will be copied to your computer.
Important notice
If you use Windows XP or Windows Vista, a message
may appear after connecting the unit with the USB
cable. This is normal and the software will not cause
any difficulties with your operating system. You can
continue the installation with no problem. This kind of
message is displayed:
L For Windows XP users
“The software you are installing for this hardware
has not passed Windows Logo testing to verify its
compatibility with Windows XP.”
L For Windows Vista users
“Would you like to install this device software?”
To view or install the operating instructions in the
CD-ROM
1. Start Windows and insert the included CD-ROM into
your CD-ROM drive.
2. Click [Operating Instructions], then follow the on-
screen instructions to view or install the operating
instructions in PDF format.
L Adobe
Note:
L If the screen prompts to insert the CD-ROM for the
operating system when installing Multi-Function
Station, insert it into your CD-ROM drive.
L If you install the operating instructions, you can view
it anytime from [o] on the Multi-Function Station
launcher.
®
Reader® is required to view them.
2. [Start] i [All Programs] or [Programs] i
[Panasonic] i the unit’s name i [Uninstall or
Modify] i [Modify] i [Next]. Then follow the
on-screen instructions.
To uninstall the software
For Windows 2000, Windows XP and Windows Vista
users, you must be logged in as an administrator in order
to uninstall Multi-Function Station.
1. [Start] i [All Programs] or [Programs] i
[Panasonic] i the unit’s name i [Uninstall or
Modify]
2. [Uninstall] i [Next]. Then follow the on-screen
instructions.
Note:
L If you want to uninstall each component, select
[Modify] and click [Next] in step 2. Then follow the
on-screen instructions.
To use another unit with the computer
You need to add the printer driver for each unit, as
follows.
[Start] i [All Programs] or [Programs] i
[Panasonic] i the unit’s name i [Add Printer
Driver]. Then follow the on-screen instructions.
Note:
L You cannot connect more than one unit to the same
computer at the same time.
To modify the software
You can select the components to install anytime after
the installation.
For Windows 2000, Windows XP and Windows Vista
users, you must be logged in as an administrator in order
to modify Multi-Function Station.
1. Start Windows and insert the included CD-ROM into
your CD-ROM drive.
24
2.11 Starting Multi-Function
Station
[Start] i [All Programs] or [Programs] i
[Panasonic] i the unit’s name i [Multi-Function
Station]
L Multi-Function Station will appear.
XXX
* The pictured screenshot is for KX-MB772.
[Scan] (page 29)
L To scan and display the scanned images.
L To scan and create an image file.
L To scan and send by e-mail.
L To scan and convert an image into editable text data.
[PC FAX] (KX-MB772 only)
L To send a document created on the computer (page
41).
L To display a document received on the computer
(page 47).
[Remote Control] (page 64)
L To program the features.
L To store, edit or erase items in directories.
L To view items in the journal report or Caller ID list.
L To store caller information into directories.
L To store or erase items for broadcast transmission.
[Utilities]
L To start Multi-Function Viewer (page 29).
L To start Device Monitor (page 64).
L To start OCR application (page 28).
[Settings] (page 25)
L To change the general settings.
L To change the settings for scanning.
[o]
L For detailed instructions on Multi-Function Station.
L To view operating instructions.
[p]
L To display usage tips.
[n]
L To display information about Multi-Function Station.
*1 KX-MB772 only
*1
*1
*1
2. Preparation
Note:
L You can confirm if the unit is connected to your
computer on Device Monitor (page 64).
L Computer features (printing, scanning, etc.) may not
function properly in the following situations:
– When the unit is connected to a computer that
was custom-built by the user.
– When the unit is connected to the computer via a
PCI card or other expansion card.
– When the unit is connected to another piece of
hardware (such as a USB hub or interface
adapter) and not connected directly to the
computer.
To change the settings
You can change the settings for Multi-Function Station
beforehand.
1. Select [Settings] from Multi-Function Station.
2. Click the desired tab and change the settings. i
[OK]
[General]
– Launcher display: To select the display type of the
launcher.
– OCR Path: To select the OCR software.
[Scan]
– Save to: To select the folder where the scanned
image will be saved.
– Viewer/File/E-Mail/OCR/Custom: To change
scanning settings for Multi-Function scan
application.
To select the default E-mail software
The default E-mail software is used when using
“4.1.3 Scan to E-mail”, page 28.
You can select the default E-mail software as follows.
For Windows XP:
1. [Start] i [Control Panel] i [Internet
*1
Options] i [Programs] i [E-mail]
2. Select the desired MAPI-compliant E-mail software
such as [Outlook Express], etc. i [OK]
L These steps may vary depending on your operating
system.
25
3. Printer
3PrinterPrinte r
3.1 Printing from Windows
applications
You can print a file created in a Windows application. For
example, to print from WordPad, proceed as follows.
1 Open the document you want to print.
2 Select [Print...] from the [File] menu.
L The [Print] dialogue box will appear.
For details about the [Print] dialogue box, click
[?], then click the desired item.
MBXXX
L If a printing error occurs, the Device Monitor will be
started automatically and display the error
information.
Setting the printer properties
You can change the printer setting in step 3. We
recommend that you test paper (especially special sizes
and types of paper) on the unit before purchasing large
quantities.
You can change or display the settings on the following
tabs.
[Basic] Paper size, media type, page per sheet, etc.
[Output] Number of prints, collate, etc.
[Quality] Resolution, contrast, toner save feature, etc.
[Effects] Watermark, overlay.
[Profile] Saving the desired settings, selecting the
saved settings, etc.
[Support] Version information.
Note:
L When printing from a computer, the toner save
feature on the [Quality] tab overrides the unit’s toner
save setting (feature #482 on page 56).
Note:
L For Microsoft PowerPoint®, select [Colour] or
remove the check next to [Greyscale] in the
print dialogue so that coloured text will be printed
in greyscale.
3 Select the unit’s name as the active printer.
L If you have changed the name of the unit when
installing, select that name from the list.
L To change the printer settings, proceed as
follows.
For Windows 98/Windows Me:
Click [Properties], then click the desired tab.
Change the printer settings, then click [OK].
For Windows 2000:
Click the desired tab and change the printer
settings.
For Windows XP/Windows Vista:
Click [Preferences], then click the desired tab.
Change the printer settings, then click [OK].
4 Click [Print] or [OK].
L The unit will start printing.
Note:
L To stop printing from the unit, see page 64.
L To load paper, see page 15, 27.
L When using the manual input tray, load the recording
paper after step 4.
L For details about the paper specifications, see page
84.
26
3. Printer
3.1.1 Using the manual input tray
You can print on plain paper and labels.
The manual input tray is used only for printing with the
computer and can hold one page at a time. When
printing multiple pages, add a next page after the first
page has been fed into the unit.
L Please refer to page 84 for information on recording
paper.
Load the recording paper after you have started
printing with the computer.
1 Adjust the width of the guides (1) to the size of the
recording paper.
2 Insert the paper, print-side down (2) until the unit
grasps the paper and a single beep is heard.
2
– Any sheet of labels that has spaces in it where
some of the labels have been removed.
– Labels that do not completely cover the backing
sheet as follows.
1
Note:
L If the paper is not inserted correctly, re-adjust the
paper, or the paper may jam.
L Make sure the unit grasps the recording paper as
specified in step 2. The display shows the following.
PAPER IN TRAY #2
FOR PC PRINTING
L To use the manual input tray, you must change the
paper source in the [Basic] tab when setting the
printer properties (page 26). You can also select the
desired media type.
To print on labels
Use labels designed for laser printing. We recommend
the following:
®
Avery
5160/5161/5162/5163/5164/5165/5167/5168
XEROX
LWH100/LWH110/LWH120/LWH130/LWH140
®
L Use the manual input tray to print labels.
L Load label sheets one page at a time for printing,
print-side down.
L Remove each label after printing.
L Do not use the following types of labels:
– Labels that are wrinkled, damaged or separated
from the backing sheet.
27
Loading...