Panasonic CZ-RWSU3U installation

Installation Instructions Wireless Remote Controller

Model No.

CZ-RWSU3U

Safety Precautions

Read before installation

Read the Installation Instructions carefully



to install the remote controller correctly and safely.

Be sure to read the Safety Precautions in

particular before installation.

After the installation is complete, perform



test operation to conrm that no abnormality

is present.

We assume no responsibility for accidents



or damages resulting from methods other than those described in the installation instructions or methods without using

specied parts.

Malfunctions that occurred due to the

unauthorised installation methods are not covered by the product warranty.

Read the installation instructions supplied



with indoor units as well.

WARNING

This symbol refers to a hazard or unsafe practice which can result in severe personal

injury or death.

CAUTION

This symbol refers to a hazard or unsafe practice which can result in personal injury or product or property damage.

WARNING

• Turn o the circuit breaker of the units

before installation.

• Ask your dealer or professionals for

installation and electric work.

• This controller shall be installed in

accordance with National Wiring Regulations.

• Connect and x the specied cables for

wiring securely.

• Do not allow the connection to be exposed to the external force of the cables.

• Choose an installation location that suciently supports the weight of the

remote controller.

CAUTION

Do not use the remote controller at the



following locations.

• Location where condensation occurs

• Location where ammable gases, etc. may

leak

• Location where corrosive gases, etc. may

leak

• Location with lots of water or oil droplets

(including machine oil)

• Location where voltage uctuation

frequently occurs

• Location where there is a machine

producing electromagnetic radiation

• Location where droplets of organic

solvents spread

• Location where acidic or alkaline solutions

or special sprays are frequently used

Do not operate with wet hands.



Do not wash with water.



Wireless Remote

Controller

(1)

Before installing the receiver,



Remote Control

Holder

(1)

see the sections on “Wiring for the Receiver” and “Setting Address Switches”. Then check the settings of the [S003] DIP switch on the receiver’s PCB.

* Remove the cover from the

receiver when performing the PCB settings.

1-1.

Part Names

1-2.

Supplied accessories

AAA Size

Battery

Instructions

(2)

1-3.

Settings

Screw

Clamper

PCB cover

Receiver PCB

Corner cover

(2) Emergency operation button

Operating

(1)

Starts/Stops emergency operation.

(3) Indication lamp

Indicates operation status.

(1) Light receiving section

Receives signals.

Wood Screw

(2)

1 2 3 4

Clamper

(1)

All set at OFF when shipped from the factory.

Main/Sub selector switch for remote controllers (4)

OFF: Main ON: Sub

Set its address (1) to (3)

Printed in Japan

85464369820010

- 1 -

DC0815-0 CV6233317632

1-4. Wiring for the Receiver

Wiring Diagram

Receiver PCBIndoor unit

Terminals for RC wiring

1 2

CN001

2P white

How to Connect the Wires

Connect the wires from the receiver to the terminals for RC wiring on the indoor unit.

・

(No polarity)

Installation Location for the Reciver



The wireless remote controllers use a very weak infrared light for its signal, which can result in the signal

not being received because of the following inuences, so take care in where the unit is installed.

• Inverter or rapid-start type uorescent lights (Models without glow lamps)

• Plasma display or LCD televisions

• Direct sunlight or other sources of bright light

Attention



Multiple wireless remote controllers cannot be used simultaneously for a single indoor unit.



Be careful not to connect cables to other terminals of indoor units (e.g. power source wiring terminal). Malfunction may occur.



Do not bundle together with the power source wiring or store in the same metal tube. Operation error may occur.



If noise is induced to the unit power supply, attach a noise lter.

*Wiring shown below is prohibited.

Wired RC Receiver

1 2 1 2

RC wiring

R1 R2

Indoor unit Indoor unit Indoor unit

R1 R2 R1 R2

1 2

Receiver

- 2 -

1-5. Installing the Receiver

The receiver can only be installed on the corner indicated in Fig. A. Consider how the panel will



face when it is installed on the indoor unit.

1 Remove the air inlet grill.

Remove the screw holding the adjustable corner cover. Then slide the cover to the side and remove it. (Fig. B)

Fig. A Fig. B

Box with

indoor unit’s electrical parts

Receiver position

3 To pass the wire through the panel, bend the part (shaded area) on the square hole and then

pass wire protruding from the wireless receiver through the grill. (Fig. C) After wiring according to the directions in “Wiring for the Receiver”, leave enough wire length so that the

receiver’s adjustable corner cover can be removed and fasten the wire with the clamper. (Fig. C)

Hang the corner cover string on the pin of the ceiling panel (Fig. D). Then slide the corner cover

onto the ceiling panel until the three clips are correctly located and x it in place with the screws.

Make sure the wire is not caught.



Refer to the installation instructions supplied with the panel.



Fig. C

Bend the part (shaded area) with a screwdriver or similar implement to allow the wire to pass through.

Adjustable corner cover

Screw

Fix it in place

with the clamper.

Fig. D

Ceiling panel

Adjustable corner cover

Installation when setting Main/Sub for the remote controller and the receiver

 Using 1 indoor unit

Installation

example

After installation, according to the “Settings” section, set one to [Main] and the other to [Sub]. Setting the wired remote controller to [Main] is recommended.

Note

Receiver (Sub) Receiver (Sub)

The remote controller and the receiver can be connected to any indoor unit for operation.

RC wiring

(eld supply)

• No polarity

Wired RC (Main)

1 21 2

R1 R2

Indoor unit

Terminals for

 Using more than 1 indoor unit

1 2 1 2

RC wiring

Indoor unit Indoor unit Indoor unit Indoor unit

- 3 -

RC wiring (eld supply)

• No polarity

Wired RC (Main)

R1 R2R1 R2R1 R2R1 R2

Fix the

screw.

Make sure the three clips on the corner cover are located over the holes on the

ceiling panel and x it in place with the

supplied screws.

For more information about wiring and test operation, see the sections on “Wiring for the Receiver” and



“Test Operation”.

- 4 -

1-6. Setting Address Switches

When more than 1 receiver is installed in the same room, setting addresses prevents



interference. For how to change addresses of wireless remote controllers, see the operating instructions of



wireless remote controllers.

To change the receiver’s address, remove the cover from the receiver’s PCB and set No.1 to



No.3 of the [003] DIP switch on PCB.

Remote Controller Address Display

Position of the receiver’s address switch

Address Address Address Address Address Address Address

ALL 1 2 3 4 5 6

Receipt is possible at all of the address positions

1234

ON/OFF

States

OFF ON

1-7. Test Operation

Preparation:

1. To start test operation, press and hold the emergency operation button for 10 seconds.

2. The indication lamps (OPERATION, TIMER, STANDBY) blink during test operation.

3. To nish test operation, press and hold the emergency operation button for 10 seconds.

Attention

 Do not use this mode for purposes other than

the test operation. (To prevent overload of the units) Read the installation instructions supplied with the units.

  Any of the Heat, Cool and Fan operations can

only be performed.

Turn on the circuit breaker of units and then turn the power on. After the power is turned

on, remote controller operation is ignored for approx. 1 minute because setting is being

made. This is not malfunction. (Contents received while setting are disabled.)

 Temperature cannot be changed.  The test operation mode is automatically

turned o in 60 minutes. (To prevent continuous test operation) Outdoor units do not operate for approx. 3



minutes after the power is turned on or operation is stopped.

1-8.

Self-diagnostics table and detected contents

 The “Alarm Display” shown in the table below expresses the alarm contents displayed when the

wired remote controller is connected. For how to handle the alarms, see installation instructions of indoor units or technical guide.

Detected contents Indication lamp on the receiver

Alarm Display

Communication error in the remote controller circuit

Communication error either in the in/ outdoor operation line or the sub-bus of the outdoor unit

Operation of indoor protection device

Operation of outdoor protection device P02–P08, P15–P31

Error in the indoor thermistor F01–F03, F10–F11

Error in the outdoor thermistor F04–F09, F12–F28

Error in the indoor EEPROM F29

Error in the outdoor EEPROM F30, F31

Error related to the compressor H01–H31

Error in indoor settings L01–L03, L05–L09

Error in outdoor settings L04, L10–L31 Error in the gas heat pump air

conditioner Inconsistency in Cooling/Heating (Including an auto-temp

setting for a model without auto-temp settings) Oil alarm (Same as operation of outdoor protection device)

Test operation

: OFF : ON (Illuminated) ◎: Blinking (0.5 seconds interval)

1-9.

Room Temperature Sensor Settings

The indoor unit and the wireless remote controller are equipped with



E01–E03, E08–E14, E17, E18

E04–E07, E15, E16, E19–E31

P01, P09–P14

A01-A31

OPERATION TIMER STANDBY

◎

 



◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎



◎ ◎





◎ ◎ ◎ ◎

◎

◎ ◎

◎









◎



◎



◎



◎ ◎

◎



Blinking

Alternately

Simultaneously

Alternately

Simultaneously

room temperature sensors. The sensing of room temperature works via one of them.

When the unit is shipped, it is set to the indoor unit. To switch it to the



remote controller, press the sensor button (the gure on the right)

inside the remote controller’s cover and then check that Main Sensor

on the LCD screen goes o.

<Note> Be sure to install the remote controller so as to face the

receiver.

Sensor button

If the unit does not receive any room temperature data from

the remote controller for ten minutes even with its sensing function activated, the indoor unit sensor will automatically start sensing the room temperature.

- 5 -

1-10.

Setting Up Remote Controller Functions

The functions of the wireless remote controller can be set on site. (These settings are saved in nonvolatile memory in the remote controller. Therefore, the settings do not revert to the defaults even when its batteries are changed.) <Note> Only service personnel should make the settings because the operation of the air

conditioner may be aected, depending on the settings made. Furthermore, making changes to these settings may cause actual operation to deviate

from what is printed in the Operating Instructions, so be sure to fully explain this to the

customer.

Making Settings (Do with unit stopped)

(1) Holding down the swing/ap ( ) + OFF timer ( ) + mode select ( ) buttons at the

same time for 4 or more seconds will open the setting screen. (See gure below.)

(2) Use the Temperature setting buttons (3) Use the ON timer buttons

/ ( ) to change settings.

/ (

(4) The settings are saved with the once/every day button (

) to select the number of the item to be set.

). When this is done, the SET

displayed on the LCD changes from blinking to lighting.

(5) If other settings are to be changed, repeat steps (2) to (4).

(6) When all settings have been made, press the start/stop (

) button.

Operation procedure and function display

Factory

setting

AM/PM

86°F (30°C) 64°F (18°C) 86°F (30°C)

(*4)

60°F (16°C) 86°F (30°C) 64°F (18°C) 80°F (27°C)

62°F (17°C)

(3)

(4)

Item Number

(6)

(2)

(1)

Detected contents Set Contents

1 Operation

Mode

2 Flap Display

3 Select Fan

Speed

4 Display of Set

Temperature 5 Time Display 6 Ventilation Fan

ON/OFF 7 Cool temp Max 41 to 95°F (05 to 35°C)

8 Cool temp Min 41 to 95°F (05 to 35°C) 9 Heat temp Max 41 to 95°F (05 to 35°C)

10 Heat temp Min 41 to 95°F (05 to 35°C) 11 Dry temp Max 41 to 95°F (05 to 35°C) 12 Dry temp Min 41 to 95°F (05 to 35°C) 13 Auto temp Max 41 to 95°F (05 to 35°C)

14 Auto temp Min 41 to 95°F (05 to 35°C)

16 Address Setting

Max Value

17 Heat temp Max

ON/OFF

(No Display)

(*1)

°F Setting O (*2) °C °F

AM/PM 24 Hour (No Display) OFF (No Display)

00 (ALL only) 01 to 031 06(*5)

JP (Heater Max Temp Change O)

EP (ON)

(No Display)

ON OFF (*3)

<Note 1> While the unit is in the SWING mode (swing/ap), the ap cannot be stopped in a

desired position. <Note 2> When Setting OFF is selected, “°C” is displayed on the LCD. <Note 3> You can toggle between ON and OFF by pressing ventilation “(

) button” for 4 seconds

or more.

<Note 4> If the Heater Max ON/OFF setting is not changed to EP (ON), the setting change will

not be reected.

<Note 5> This is the number of addresses that can be set in the address change mode. Do not

set it to 07 or above.

- 7 -

- 6 -

1-11.

Installing Wireless Remote Controller

Installation location for the Wireless Remote Controller

If a remote controller is to be operated from a remote control holder that is hung on a wall, turn on the lights in



the room as well as any electrical appliances and then check to make sure the air conditioner works with the remote controller in the location where it will be installed. If it works, continue with installation.

If the main sensor is to be switched from the indoor unit to a remote controller, pay attention to the following



when installing.

•

Locate where no warm or cold air will aect it.

•

Locate in a place free from direct sunlight.

•

Locate where it will not be aected by any other heat/cold source.

1-12.

When installing the remote controller onto a wall, etc.

Screw the remote control holder.

Remote control holder

Installing the remote controller

Press

Insert

Press



on the wall, and check that normal receiving is possible.

Remove the remote controller from the



remote control holder.

at the installation location

1-13. Specications

Wireless Remote Controller

Dimensions

Weight 140g (Including batteries) Power Source Two AAA size batteries Clock Accuracy ±30 seconds / month (at 77°F (25°C))

Receiver

Dimensions

Weight 140g Power Source DC16V(supplied from indoor unit)

(H) 7-11/64” × (W) 2-13/32” × (D) 47/64” ((H)182 mm × (W) 61 mm × (D)18.5 mm)

(H) 7-7/8” × (W) 7-7/8” × (D) 63/64” ((H) 200 mm × (W) 200 mm × (D) 25.2 mm)

- 8 -