Panasonic cz-rd516c1 Operation Manual
Accessories
g
f
e
3
5
1
4
2
h
Remote Control Preparation
• Press
and hold for approximately 5
seconds to show 12-hour (am/pm) or 24-hour
time indication.
1.
Press
2.
Press
or to select current day.
3.
Press
to confi rm.
4. Repeat steps 2 and 3 to set the current time.
Wired remote control
d
g
f
e
3
5
1
4
2
6 7 910 8
h
a
b
c
Wired Remote: CZ-RD516C1
New Wired Remote
Job Name:
Location:
Engineer:
Submitted to:
Submitted by:
Reference:
Features/Benefits
Filter Check Display
Mode Selection
Set Temperature
Fan Speed Control
Airflow Direction
Applications
Hotel Rooms
Assisted Living
Offices
Dorm Rooms
d
c
b
a
Remote Control Preparation
• Press
1.
2.
3.
4. Repeat steps 2 and 3 to set the current time.
6 7 910 8
seconds to show 12-hour (am/pm) or 24-hour
time indication.
and hold for approximately 5
Press
Press
Press
or to select current day.
to confi rm.
Approval:
Date:
Construction:
Unit#:
Drawing#:
e
f
g
h
1
4
3
2
5
Remote Control Display
a
b OFF INDICATOR
c
d TIMER/CLOCK SETTING DISPLAY
e
f TEMPERATURE SETTING DISPLAY
g
h
OPERATION LED
OPERATION MODE SELECTION
INDICATOR
Lights up if Timer operation is selected
6 different
programmes can be
set in a day (1 ~ 6)
Indicates the selected
day
Indicates the next
timer operation day
Time to be selected
(10 minutes step)
OFF Timer. To automatically
switch “OFF” the unit.
ON Timer. To automatically switch “ON”
the unit.
Day to be selected
FAN SPEED DISPLAY
ERROR CODE DISPLAY
FILTER CHECK INDICATOR
English
3
Press the remote control’s button
1
TO TURN ON OR OFF THE UNIT
• Please be aware of the OFF indication on the
remote control display to prevent the unit from
starting/stopping improperly.
2
TO SET TEMPERATURE
• Selection range: 60°F ~ 86°F.
3
TO SELECT OPERATION MODE
AUTO mode - For your convenience
• Unit selects operation mode during startup
according to temperature setting and room
temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up. The power
indicator blinks during this operation.
COOL mode - To enjoy cool air
• Use curtains to screen off sunlight and outdoor
heat to reduce power consumption during cool
mode.
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle
cooling operation.
4
TO SELECT FAN SPEED
FAN SPEED
• For AUTO, the indoor fan speed is
automatically adjusted according to the
operation mode.
5
TO ADJUST AIRFLOW DIRECTION
• Keeps the room ventilated.
• In COOL/DRY mode, if AUTO is set, the louver
swing left/right and up/down automatically.
• In HEAT mode, if AUTO is set, the horizontal
louver fi x at predetermined position. The
vertical louver swing left/right after the
temperature rises.
• For Hide-Away models, AIR SWING buttons
are not in use. Airfl ow direction can not be
adjusted.
Press and hold for approximately 10
6
seconds to show temperature setting in °C
or °F.
9
RETRIEVE ERROR CODE
• During operation, the unit stops and both
andb is OFF indicates abnormality occurs.
1. Ensure a is OFF, press
2. Press or . If error code and abnormality
can be identifi ed,
then write down the error code.
3. Press
4. Turn the unit off and reveal the error code to
authorized dealer.
Note: Press
10
Cleaning is needed when “FILTER CHECK”
indicator is ON.
• lt is recommended to clean the air fi lter every 6
weeks.
• After the air fi lter is cleaned, press
reset.
• Do not operate without an air fi lter.
• Wash/rinse the fi lters gently with water to avoid
damage to the fi lter surface.
• Do not dry the part with a hair dryer or a stove.
• Replace any damaged fi lters.
for 5 seconds to quit checking.
switch (Not used in normal operation).
AIR FILTER MAINTENANCE
a
will be ON continuously,
for 10 seconds to enter AC reset
for 5 seconds.
a
to
7
8
Panasonic North America
Air Conditioning Division
1690 Roberts Blvd., NW, Suite 110
Kennesaw, GA 30144
http://www.panasonic.com/aircon
Press and hold for 5 seconds to dim or
restore the unit’s indicator brightness.
Press to restore the remote control’s
default setting.
Data is Subject to Change.
Loading...