This symbol located near the fuse indicates that the
fuse used is slow operating type, For continued protection against
fire hazard, replace with same type fuse, For fuse rating, refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
REF NO.PART NAMEDESCRIPTIONPART NO. REMARKS
F6401, F6402
F6401, F6402 or
F9002
F9002 or
F9002
F9002 or
F9001
F201
[Notes]
<MDC> : 120V,Canadian model
<MMP> : 220-240V,CE(European) country model
<MMQ> : 220/230-240V,Hong kong model
<MMA> : 220-240V,Australian model
<MMR> : 220/230-240V,Chinese model
<MDF> : 120V,Taiwanese model
!
!
!
!
<MDC, MDF>
!
<MDC, MDF>
!
<MMA, MMP, MMQ, MMR>
!
<MMA, MMP, MMQ, MMR>
!
2. Safety check out
(U.S.A. model only)
After correcting the original service problem, perform the following safety check before releasing the unit to the customer.
Leakage current Check
Measure the leakage current to a known earth ground (water pipe or conduct etc.) by connecting a leakage current
tester between the earth ground and exposed metal parts of the unit (input/output ground terminals,
screw heads or metal overlays etc.).
Plug the power supply cord directly into a 120Vac 60Hz wall socket and turn ON/STANDBY button on.
Any current measured must not exceed 0.5mA.
3. To initialize the unit
Press ON/STANDBY button while pressing down CBL/SAT button
when the unit is POWER ON, then the FL displays "CLEAR", and turn to STAND-BY. Remove power cord from power line.
4. To check version of each Firmware
a. Push ON/STANDBY key while pushing down DISPLAY key to display MMPU(Main Microprocessor) version.
e.g.
M1.04/13515AE
b. In display version, - (TONE) key and + (TONE) key are pushed to display another F/W version.
-
(TONE)
e.g.
M1.04/13515AE
-
(TONE)
e.g.
D1.07/13514AEA
-
(TONE)
e.g.
V1.02/13325AE
-
(TONE)
e.g.
K1.01/13322AEO
-
(TONE)
+(TONE)
+(TONE)
+(TONE)
+(TONE)
+(TONE)
O1.00/12Z18AE
Version of MMPU displayed only for 3 seconds.
MMPU
(Main Microprocessor)
DSP
HDMI/VIDEO Microprocessor
VSP
(Video Signal Processor)
VSP2
(Video Signal Processor)
Version displayed
only for 3 seconds.
SERVICE PROCEDURE-2
5. Notes on repairs (Power supply board)
Some parts on BAPS-1333 may remain high voltages even after the power cord is disconnected from AC power source.
Before starting repair and any other work , please discharge C9002 by connecting resistors between its terminals.
See the figure below(recommended resistor spec: 5 k ohms/ 10W)
It is dangerous to touch the "HIGH VOLTAGE PRIMARY" area surrounded by white lines without discharging.
U0063
POWER SUPPLY(PRI) PC BOARD ASS'Y
BAPS-1333
TX-NR727
Resistor
HIGH VOLTAGE PRIMARY
Top
TX-NR525/ 626/ 727/ HT-RC550/ 560/ DTR-30.5/ 40.5
DEBUG MODE-1
AUDIO DEBUG MODE-1/5
The operations of DSP and DIR etc are able to checked by the information displayed on FL in this debug mode.
This information will help to analysing digital audio no sound trouble.
To set in Debug mode
1. Press twice the ON/ STANDBY key while pressing the DISPLAY key.
2. Press + (TONE) button while the version number of microprocessor is displayed.
3. Press DISPLAY button while the version number of DSP is displayed.
4. Proceed to the next step by pressing the DISPLAY key.
e.g.
e.g.
e.g.
M1.01/13204ALN
D1.02/13202AEA
0A0002:__:00__
The version number of Microprocessor is displayed
only for 3 seconds.
The version number of DSP is displayed
only for 3 seconds.
HDMI-related operations can be checked to some extent by displaying HDMI debug mode.
To enter this mode
Hold down DISPLAY button for 3 seconds. Information display will last for about 8 seconds.
Resolution display method
Input resolution
Output resolution
List of standard resolution
Display of Input Resolution
DVI input signal
VGA input signal
No input
“I” and “P” will be capitalized.
Display the ” ” in column 1
DEBUG MODE-7
→ 1 0 8 0i/6 0
1 0 8 0i/6 0
4 8 0I/6 0
4 8 0 P /6 0
*4 8 0
p
/6 0
4 8 0 p /6 0 *
4 8 0 p /6 0
#
4 8 0 p /6 0
x
-----
O F F
1 0 8 0i/6 0 →
*** *x *** *p /**
***
3 8 4 0 x 2 1 6 0 p /3 0
3 8 4 0 x 2 1 6 0 p /2 5
3 8 4 0 x 2 1 6 0 p /2 4
4 0 9 6 x 2 1 6 0 p /2 4
3 8 4 0 x 2 1 6 0 p /3 0 x
3 8 4 0 x 2 1 6 0 p /3 0 #
1 0 8 0
p
/2 4
(
3 D
)
H D M I4 4 43 6 bit
F ra m eP a c kin g
I N
:
O U T
:
1 0 8 0
p
/2 4(3 D )*
H D M I4 4 4 # 3 6 bit
1 0 8 0
p
/2 4
(
3 D
)
x
HDMI DEBUG MODE-2/4
Dislay of Output Resolution
For a video processor
Via VSP
Display the ” ”
in column 4
VSP skip
TX-NR525/ 626/ 727/ HT-RC550/ 560/ DTR-30.5/ 40.5
DVI input signal
VGA input signal
RSEN is OFF
EDID_READ is NG
Resolution Error
No output
(Signal output destination
can not be found.)
Hot-plug of Sink equipment
can not be detected.
4K Upscaling
Display of Input resolution
Display of Output resolution
List of resolution
i / p will be
capitalized.
Display the ” ”
in column 5
Display the ” ”
in column 14
Display the ” # ”
in column 14
Display the ” x ”
in column 14
→
If the three-digit numbers
are refrate
Resolution Error
EDID_READ_NG
3D Display
Resolution display
Status Display
3D format
INPUT/OUTPUT
RSEN OFF
EDID READ NG
Resolution Error
Display the ” ”
in column 14
Display the ” # ”
in column 9
Display the ” x ”
in column 13
DEBUG MODE-8
H D M I4 4 43 6 bit
D V I4 4 43 6 bit
---4 4 43 6 bit
H D M IR G B3 6 bit
H D M I4 2 23 6 bit
H D M I4 4 43 6 bit
H D M IR G B2 6 bit
H D M IR G B3 0 bit
H D M IR G B3 6 bit
F r a m eP a ck in g
Falt e r n ativ e
Lalt e r n a tiv e
S i d e b y Si d e ( F )
L + d e p t h
L + d e p t h g r a p h i c
S i d e b y Si d e ( H )
T o p - a n d - B o tt o m
U N K N O W N
I N
:* *
O U T
:* *
HDMI DEBUG MODE-3/4
Status
Input Mode
Input Color
Deep Color
HDMI input
DVI input
No input
RGB
422
444
24bit
30bit
36bit
TX-NR525/ 626/ 727/ HT-RC550/ 560/ DTR-30.5/ 40.5
3D format
Frame Packing
Field alternative
Line alternative
Side-by-Side(Full)
L+depth
L+depth + graphics
Side by Side(Harf)
Top and Bottom
unknown
INPUT/ OUTPUT
DEBUG MODE-9
1 0 2 4 x7 6 8 p /6 0 →
1 0 2 4 x7 6 8 p /6 0
****x ****p/**
→
1 0 2 4 x7 6 8 P /6 0
→
1 0 2 4 x7 6 8 p/6 0
→
1 0 2 4 x7 6 8 P 1 2 0
→
U N K N O W N
****x ****
p
/**
1 0 2 4 x7 6 8 P /6 0
1 0 2 4 x7 6 8 p/6 0
→
-----
1 0 2 4 x7 6 8 P 1 2 0
1 0 2 4 x7 6 8 P /6 0 #
1 0 2 4 x7 6 8 P /6 0
x
I N
:
*O U T
:
*
HDMI DEBUG MODE-4/4
PC Resolution
Input Resolution
Output Resolution
Display of Input resolution
TX-NR525/ 626/ 727/ HT-RC550/ 560/ DTR-30.5/ 40.5
DVI input
HDMI input
Three-digit numbers
are Referat
No input
Display uppercase P/I
Display lowercase p/i
Display of Output resolution
DVI output
HDMI output
Display uppercase P/I
Display lowercase p/i
Horizontal resolution
Horizontal resolution
Vertical resolution
Vertical resolution
Referat
Referat
Display”-----”
Three-digit numbers
are Referat
EDID READ NG
Resolution through
INPUT/ OUTPUT
Display the ” # ” in
column 13
Display the ” x ” in
column 13
TX-NR525/ 626/ 727/ HT-RC550/ 560/ DTR-30.5/ 40.5
DEBUG MODE-10
SERVICE INFORMATION MODE
Displaying Service information
This service information display system is helpful in analyze the status when the unit goes into Protect mode and is powered off.
Pay attention that the status will change if a button is pushed.
1. Press twice the ON/ STANDBY key while pressing the DISPLAY key.
e.g.
M 1 . 0 1 / 1 3 2 0 4 A L N
2. Press HOME button within 3 seconds above.
e.g.
- 8 0 F 2 7 D D
The version of main microprocessor is
displayed only for 3 seconds.
Information Displayed (Record this Information)
Power off Cause
T : Thermal Protect
Temperature
: xx F or xx C
Volume LevelListenning Mode
---> Refer to the code list below.
V : Voltage Protect
I : Current Protect
- : Other
Listening Mode Code List
C_LM_LAST01
C_LM_PURE02
C_LM_DIRECT03
C_LM_STEREO04
C_LM_MONO05
C_LM_SURR20
C_LM_THX_MUSIC50
C_LM_THX_GAME70
C_LM_THX_CINEMA90
C_LM_THX_U2GAMEA0
C_LM_THX_U2MUSICA8
C_LM_THX_U2CINEMAB0
C_LM_AUDYSSEYD0
C_LM_DTSSS48
C_LM_ORCHESTRA06
C_LM_UNPLUGGED07
C_LM_STUDIOMIX08
C_LM_TVLOGIC09
C_LM_ALLCHST0A
C_LM_FULLMONO0B
C_LM_TD0C
C_LM_TESTTONEF1
C_LM_TESTTHRF2
C_LM_TESTAUTOF3
3. Press HOME button again. The following information are displayed.
e.g.
0 1 : 2 3 1 0 h
Time after Power on
xx : xx
Time after Initialize
xx hour
Information Displayed (Record this Information)
C_LM_ASCF4
C_LM_FLASHF5
C_LM_DEBUGMODEF6
C_LM_FLASH2F7
C_LM_FLASH3F8
C_LM_FLASH4F9
C_LM_FLASH_CHECKFA
C_LM_RPG0D
C_LM_ACTION0E
C_LM_ROCKBAND0F
C_LM_SPORTS10
4. Press ON/STANDBY button to exit the display of service information.
(Ref.: Press RETURN button to initialize the data in the service information.)
P r o t e c t D a t a C L R
Normal display
TX-NR626/727/828/ HT-RC560/ DTR-30.5/40.5/50.5
OPERATION CHECK-1
1.OPERATION CHECK(1/3)
1-1. OPERATIONS OF VOLTAGE-DETECTION PROTECTORS.
See “OPERATION CHECK-4,-6” for TEST MODE operation.
NOTE: Don't connect load nor short speaker terminals.
a. Change the state to "TEST-4-21".
b. It tests by being automatic in order of TEST 4-21(FL+) → 22(FR-) → 23(C+) → 24(SL-) → 25(SR+) → ( 26(SBL-)
→ 27(SBR+) ). If TEST 4-27 is OK, it becomes the display of "TEST-4-35".
c. It will complete, if displayed on FL TUBE as "TEST 4-35".
1-2. OPERATIONS OF CURRENT-DETECTION PROTECTORS
See “OPERATION CHECK-4,-6” for TEST MODE operation.
a. Change the state to "TEST-4-35".
b. Even if you connect 3-ohm load for every channel of L, R, C, SL, SR, SBL and SBRch, a relay should not cut off.
c. If 1-ohm load is connected for every channel of L, R, C, SL, SR,SBL and SBRch, a relay should hold the state of ON.
1-3. CONFIRMATION OF RDS (RADIO DATA SYSTEM) OPERATION (Applied to MPP/MPB/MM* type)
a. Input 98MHz,30dBμ signal modurated with RDS data.
b. When a PS information is received, the name of the station "RDS TEST" shall be displayed within 2 seconds instead
of the frequency.
1-4. CONFIRMATION OF HEAD PHONE OPERATION.
Confirm the Listening Mode is automatically switched to "STEREO" mode when headphones plug is inserted into
the PHONES jack.
1-5. COMFIRMATION OF FRONT USB
See “OPERATION CHECK-4,-5” for TEST MODE operation.
a. Connect ipod to AVR USB port.
b. When set to TEST 3-09, confirm that the display of AVR change device name after few seconds.
1-6. COMFIRMATION OF NETWORK
See “OPERATION CHECK-4,-5” for TEST MODE operation.
a. Connect the receiver to the router.
b. When set to TEST 3-18 confirm that the display of AVR change IP adress.
*Please wait for about 1 minute after turning on the power supply of the set when you use TEST 3-18.
1-7. CONFIRMATION OF OUTPUT SENSOR AND THERMAL SENSOR
See “OPERATION CHECK-4,-6” for TEST MODE operation.
a. Set the TEST MODE to "TEST 4-36".
After light "FM STEREO" on FL display,
the relays RL641/642 is OFF and "FM STEREO"is off .
b. Push ON/Standby button 2 times while pushing down DISPLAY button to display CPU Debug PROGRAM version.Push TONE button while displaying CPU PROGRAM version to display value of temparature sensor. Confirm outside temperature ±20C is displayed immediately after energizing.
Note that the error margin is caused by the rise of the temperature of the heat sink when time passes.
FL Display
000 034 F:x S:H
Voltage
of VOLH port
Temparature
of thermal sensor
FAN condition
x: Stop
L: Low speed
M: Mid speed
H: High speed
Amplifier power
supply voltage condition
H: High-B
L: Low-B
1-8. CONFIRMATION OF OSD(ON SCREEN DISPLAY) OPERATION
a. When SETUP button is pushed, confirm that setup menu is displayed in HDMI Out.
b. Confirm that specified operations for ENTER(with 4-cursor) buttons are made.
TX-NR626/727/828/ HT-RC560/ DTR-30.5/40.5/50.5
Compon entHDMI
BD/DVDAIN1FIN1H
CBL/SATB
IN2 GIN2I
STB/DVRC
---GIN3J
GAMED------IN4K
PC
P------IN5L
IN6---------IN6M
IN7---------IN7N
AUXE------AUXO
Video Signal - >
Composite Video
OPERATION CHECK-2
1.OPERATION CHECK(2/3)
1-9. CONFIRMATION OF HDMI AUDIO OPERATION.
See “OPERATION CHECK-4,-7” for TEST MODE operation.
a. CONFIRMATION OF HDMI I2S SIGNAL
1. Input the one of these signals below from HDMI1 terminal.
DTS-HD MasterAudio 7.1ch
Dolby TrueHD 7.1ch
2. Change the state to TEST 6-00. Confirm the signal is output from L/R,SW/C,SL/SR,SBL/SBR.
3. When TEST 6-08, confirm the sound(HDMI1 input) outputs from the TV.
b. CONFIRMATION OF HDMI SPDIF SIGNAL
4. SPDIF signal is input from HDMI terminal.
5. When TEST 6-06, confirm the sound(HDMI IN1) outputs from the speaker.
6. When TEST 6-07, confirm the sound(BD/DVD analog input) outputs from the TV.(VIDEO is Blueback)
c. CONFIRMATION OF HDMI DSD SIGNAL.
7. When TEST 6-10,11,12, confirm the sound of DSD 5.1ch input HDMI IN 3, output from the speaker.
1-10. VIDEO FUNCTION CHECK
See “OPERATION CHECK-4, -7” for TEST MODE operation.
a. Confirm Video output signal as shown Table 2, while Video signal are input as shown Table 1.
NOTE 1: Confirm the HDMI path at 1080p signal.
Table 1
Table 2
TX-NR626
Test mode
5-00(BD/DVD)AFH
5-01(CBL/SAT)B---I
5-02(STB/DVR)------J
5-03(GAME)D---K
5-04(PC)P---L
5-05(IN6)------M
5-06(IN7)--------5-07(AUX)E-----5-08(BD/DVD)*A*FF
5-09(BD/DVD)*A---A
1. Confirm "RDS" light up on FL TUBE when component video signal is input in "TEST 5-00".
Confirm "RDS" turn off on FL TUBE when component video signal isn't input in "TEST 5-00",too.
2. Confirm "FM STEREO" light up on FL TUBE when component video signal is input in "TEST 5-00".
Confirm "FM STEREO" turn off on FL TUBE when component video signal isn't input in "TEST 5-00",too.
1-11. CONFIRMATION OF 12V TRIGGER OPERATIONS(TX-NR828,DTR-30.5/40.5/50.5 ONLY)
See “OPERATION CHECK-4, -5” for TEST MODE operation.
a. After checking that there is no output from 12V TRIGGER A terminal,it checks that there is an output of 12V±10%/150mA
after switched the "TEST2-11".
b. After checking that there is no output from 12V TRIGGER B terminal,it checks that there is an output of 12V±10%/25mA
after about 1 seconds switched the "TEST2-12". (DTR-30.5/40.5/50.5 ONLY)
c. After checking that there is no output from 12V TRIGGER C terminal,it checks that there is an output of 12V±10%/25mA
after 2 seconds switched the "TEST2-13". (DTR-30.5/40.5/50.5 ONLY)
1-12. CONFIRMATION OF COOLING FAN OPERATION
See “OPERATION CHECK-4,-6” for TEST MODE operation.
a. Confirm to fan no rotate.
b. When TEST 4-36 or TEST 4-37, confirm to fan rotate.
1-13. CONFIRMATION OF Wi-Fi CONNECTION
a. After setting wifi routers, change the state to "IDLING TIMER MODE".
See “OPERATION CHECK-4, -6” for TEST MODE operation.
b. It connects an access point automatically. Wi-Fi LED flashes during connection.
c. When connection is completed and IP address is able to be acquired, Wi-Fi LED lights up and the value of RSSI
to an access point is displayed per dbm.
If the connection failed, NG is displayed.
* If the connection failed, exit the idle mode by pressing the TV/CD button and please try again from [a].
1 -45d 00:10:00
SSID No
1-14. MISCELLANEOUS
a. Confirm all input and output terminals operate normally.
b. Please confirm LED and FL displaying by the FL test mode. And confirm the destination setting.
---> See to “OPERATION CHECK-4” for TEST MODE operation.
c. Change the state to KEY TEST under TEST MODE described in Section 2-2. to confirm each key operation.
---> See to “OPERATION CHECK-4” for TEST MODE operation.
d. Confirm the version of each firmware.---> See to “SERVICE PROCEDURE-2”
e. Confirm the firmware combination check.---> See to “OPERATION CHECK-4” for TEST MODE operation.
f. CPlease confirm the Check Sum.---> See to “OPERATION CHECK-4” for TEST MODE operation.
Time CounterRSSI(dbm)
TX-NR626/727/828/ HT-RC560/ DTR-30.5/40.5/50.5
FL Display
OPERATION CHECK-4
2.TEST MODE(1/4)
2-1.TEST MODE FOR MODEL, DESTINATION AND FL DISPLAY
NOTE: If VOL value is not 25(initial setting), test mode cannot be set.(TX-NR626, HT-RC560, DTR-30.5)
NOTE: If VOL value is not 30(initial setting), test mode cannot be set.(TX-NR727, TX-NR828,DTR-40.5, DTR-50.5)
a. Push STANDBY/ON key while pushing down TV/CD button button to display "TEST-".
b. Then push DIMMER(RT/PTY/TP) button and get the FL test mode.
c. In the FL test mode, TONE - button is FL TEST UP and TONE + button is FL TEST DOWN.
d. REC OUT and ZONE2 button's originally operation can't work when it is in FL test mode.
e. The contents of the step are as follows.
1. Lit all segment
2. Lit '23456789ABCDEF'
3. Lit a even number segment
4. Lit an odd number segment
5. The Destination setting is displayed. Please see the below for detail.
f. To close the FL test, push POWER button.
Display of Destination on TEST MODE.(Distination setting))
DTR-30.5Dx20402040 DTR-30.5 Dx
DTR-30.5xx80408040 DTR-30.5 xx
DTR-30.5JJ40404040 DTR-30.5 JJ
A B
D
C
A:Value of AD port of BAND
B:Value of AD port of INIT1
C:Value of AD port of INIT2
D:Value of AD port of INIT3
N R 6 2 6D x2 0 0 0
N R 6 2 6D F0 0 0 0
N R 6 2 6x x8 0 0 0
N R 6 2 6J J4 0 0 0
R C 5 6 0D x2 0 0 2
D T R 3 0 5D x2 0 4 0
D T R 3 0 5x x8 0 4 0
D T R 3 0 5J J4 0 4 0
DTR-40.5Dx22402240 DTR-40.5 Dx
DTR-40.5xx82408240 DTR-40.5 xx
TX-NR828DD/DC24002400 TX-NR828 Dx
TX-NR828xx84008400 TX-NR828 xx
DTR-50.5Dx24402440 DTR-50.5 Dx
DTR-50.5xx84408440 DTR-50.5 xx
N R 7 2 7D x2 2 0 0
N R 7 2 7D F0 2 0 0
N R 7 2 7x x8 2 0 0
N R 7 2 7J J4 2 0 0
D T R 4 0 5D x2 2 4 0
D T R 4 0 5x x8 2 4 0
N R 8 2 8D x2 4 0 0
N R 8 2 8x x8 4 0 0
D T R 5 0 5D x2 4 4 0
D T R 5 0 5x x8 4 4 0
2-2. TEST MODE FOR OPERATION
a. Push STANDBY/ON button while pushing down TV/CD button to display "TEST-_".
b. Next, if the following keys are pushed, it becomes a each TEST MODE.
c. In the test mode, (TONE)- button is TEST MODE DOWN and (TONE)+ button is TEST MODE UP.
d. "TEST-1-00" and "TEST-1-01" are used to check a protection circuit, and the relay recovered in one second.
Press twice the ON/ STANDBY key while pressing the DISPLAY key.
5-00
PC
AUX
GAME
GAME1
FIRMWARE
COMBINATION
CHECK
GAME2
ENTER
PC
6-00KEY TEST
TUNER
AUX
PC
CHECK SUM
When MMPU debug version(*1)
is displayed, push
"MEMORY"
MEMORY
TX-NR626/727/828/ HT-RC560/ DTR-30.5/40.5/50.5
OPERATION CHECK-5
2.TEST MODE(2/4)
2-2. TEST MODE FOR OPERATION(Continue)
e. Test mode is as follows.
[NOTE] Do not connect the loudspeaker.
Analo g InputListening Mo de/VIDEOCompo -HDMI 12V Digital Input Config.Master Vol. Speakeretc.
No [Rec Sel]Inpu t FormatInputn ent VTRG / OutputNonTHXRelay
*1: All SP-RELAYs are turned ON only at the time of this STEP.
Moreover, whether make RELAY restoration time at the time of protection operation into 1 second, and PROTECT input
"H" is detected
how many times or it continues 1 second or more, RELAY is not held at OFF or POWER OFF is not carried out, either.
When "H" is 1 seconds or more to PROTECT input and it is set to "L", RELAY is turned ON again.
Moreover, not any MUTE is outputted at the time of this STEP.
OPERATION CHECK-6
2.TEST MODE(3/4)
2-2. TEST MODE FOR OPERATION(Continue)
Auto Measurement Mode
TEST
DSP Output ch
No.
4-00
ALL
4-01
ALL
4-02
ALL
4-03
SW
4-04
FL,FR
4-05
FR,C,SL,SR,SBL,SBR,SW
4-06
FL,C,SL,SR,SBL,SBR,SW
4-07
FL,FR,SL,SR,SBL,SBR,SW
4-08
FL,FR,C,SR,SBL,SBR,SW
4-09
FL,FR,C,SL,SBL,SBR,SW
4-10
FL,FR,C,SL,SR,SBR,SW
4-11
FL,FR,C,SL,SR,SBL,SW
4-12
FL,FR,C,SL,SR,SBL,SBR
4-13
ALL
4-14
ALL
4-15
ALL
4-16
ALL
4-21
FL
4-22
FR
4-23
C
4-24
SL
4-25
SR
4-26
SBL
4-27
SBR
4-28
FL
4-29
FR
4-30
C
4-31
SL
4-32
SR
4-33
SBL
4-34
SBR
4-35
ALL
4-36
"FL,FR,C,SL,SR"
4-37
C,SL,SR,SBL,SBR
4-38
*7
DSP Output
Frequency
1kHz
30Hz
20kHz
30Hz
30Hz
10kHz
10kHz
10kHz
10kHz
10kHz
10kHz
10kHz
30Hz
1kHz
30Hz
1kHz
30Hz
+DC
-DC
+DC
-DC
+DC
-DC
+DC
-DC
+DC
-DC
+DC
-DC
+DC
-DC
Pulse
1kHz
1kHz
DSP
Output
Voltage
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
-20dBFS
+Max
-Max
+Max
-Max
+Max
-Max
+Max
-Max
+Max
-Max
+Max
-Max
+Max
-Max
Max
0dBFS
0dBFS
Config.
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
N/L/L/L/L
N/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
Y/L/L/L/L
TX-NR626/727/828/ HT-RC560/ DTR-30.5/40.5/50.5
Master Vol.
64(Ref)
64(Ref)
64(Ref)
58(76)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
64(Ref)
Min(Min)
Min(Min)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
Max(Max)
58(76)
64(Ref)
64(Ref)
Speaker
Relay
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
F/CS/SB
etc.
*6
*6
*6
*6
*6
Mute:FL *6
Mute:FR *6
Mute:C *6
Mute:SL *6
Mute:SR *6
Mute:SBL *6
Mute:SBR *6
Mute:SW *6
*mut on *6
*mut on *6
*6
*6
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*3
*1,*4
vol=64
*5
DSP Gain
DSP Freq.Response
DSP Freq.Response
Characteristic(1)
Characteristic(2)
Separation
Separation
Separation
Separation
Separation
Separation
Separation
Separation
Muting
Muting
Volume Max.Attenuation
Volume Max.Attenuation
+DC Protect
-DC Protect
+DC Protect
-DC Protect
+DC Protect
-DC Protect
+DC Protect
-DC Protect
+DC Protect
-DC Protect
+DC Protect
-DC Protect
+DC Protect
-DC Protect
Current Protect
VOLH DET,FAN Low
VOLH DET,FAN High
Key Test,SEC1H="L"
*3 : When TEST No. 4-21 34 is setted, DC votage is putted out immediately at each channel. (within 100msec.)
*4 : The following signal is putted out at all channel continuously in TEST4-35
Max
Max
2 mS 2 mS
20 mS
*5 : VOLH is detected and H/L of SEC1H is changed.
A detection level is the same as the normal mode.
When it is detected, light "FM STEREO" on FL TUBE.
*7 : In TEST4-38, some character is displayed while pushing down some button. Another character shall be displayed
by each button.
1. DSP Thru of Listening Mode outputs L Input signal to L/C/SL/SBL, and outputs R Input signal to R/SR/SBR/SW.
2. Config. is in order of SW/Front/Center/Surround/Surround Back
3. Mute is function to stop output(from the channel) by using inner DSP programming.
4. When Listening Mode is DSP thru, an analog SW is changed into the state of SURROUND.
5. At the time of PRTCTTHM detection, it is displayed on FLT as "THERMAL PROTECT".
f. Following frequencies are automatically written in the preset memory, when the unit goes into test mode.
OPERATION CHECK-8
COOLING FAN
Circuit
Thermal sensor
OFF
MID
THERMAL
VOLH
OFF or
Headphone
LOW
LOW
LOW
Q6300
Power amp.
Condition to operate
THERMAL
LOW
TX-NR626/727/828/ HT-RC560/ DTR-30.5/40.5/50.5
139
140
Normal/ Bi-Amp
Q701
(Main Microprocessor)
MPU
LOWMID
STOP
STOPSTOPSTOPSTOPSTOPSTOP
LOWLOW
Value D/A output of the MPU
OFF
LOW
MID
HIGH
FANCTRL
3
VOLH
HIGH
LOWLOWLOWLOWLOW
MIDMIDMIDMIDMIDMIDMID
OFF or
Headphone
0V
1.7V
2.2V
2.5V
Fan drive
Q8701,
Q8711
Powerd Zone-2, 3
LOWMID
COOLING FAN
HIGH
HIGH
MID
HIGH
THERMAL(Temparature of thermal sensor)
60
55
Shut down
immediately
-30
OFF
Hysteresis control
VOLH(Voltage of VOLH port)
OFF
0.35V
0.4V
LOW
1.9V
2.0V
Hysteresis control
How to check
1. How to check Cooling Fan.
See 1-12 in ”OPERATION CHECK-2”.
2. How to check the value of THERMAL and VOLH.
See 1-7 in ”OPERATION CHECK-1”.
LOW
MID
HIGHHIGHHIGHHIGHHIGHHIGH
65
62
MID
2.3V3.3V
2.2V
HIGH
73
75
HIGH
95
Shut down in
10 minutes
continuously
100
Shut down
immediately
TX-NR727
EXPLODED VIEWS-1
OVERALL
P9001
A093
A089
U0063
SCREW
4TTC+8C(3BC)SR
x 4 pcs.
MMP, MDF only
SCREW
3TTF+10B(3BC)
x 2 pcs.
P9007
SCREW
3P+6FN(3BC) x 9 pcs.
U011
F9002
T901
A729
F6401
F6402
SCREW
3TTB+8B(3BC)
x 2 pcs.
U0080
SCREW
3P+10FN(3BC)
U0040
U0035
U0010
SCREW
3TTB+8B(3BC)
U0062
SCREW
3TTB+8B(3BC)
x 4 pcs.
U0020
U0032
x 3 pcs.
SCREW
3TTB+8B(3CM)SR
X 2 pcs.
U0031
A023
x 4 pcs.
SCREW
3TTB+8B(3CM)SR
X 2 pcs.
U0011
A021
x 4 pcs.
SCREW
3SMH10W.SW+15B(CU)
x 14 pcs.
U0030
SCREW
3TTB+8B(3BC)
x 6 pcs.
U0012
U791A
WiFi & Bluetooth Module
Except MDC, MDF, MMR
SCREW
2.6TTB+8B(3BC)
x 27 pcs.
U0061
P8651
U0041
P2510
U0100
U0060
U0065
U0036
A219
U0081
U0050
Black Model
3TTB+8B(3BC)
x 8 pcs.
Silver Model
3TTB+8B(3CM)SR
x 8 pcs.
U0033
SCREW
3TTB+8B(3CM)SR
X 4 pcs.
U791B
A209
Q6056
A221
A701
Q6054 Q6064
Q6066
P701
U791C
A207
A211
A721
MDC only
Q6052
Q6051
Q6061
<NOTE>
U791 = U791A + U791B + U791C
WiFi & Bluetooth Module
“Refer to EXPLODED VIEWS-2”
This module transmitter does not have RF shielding,
therefore it will be equipped only the tested Audio system
mentioning this document.
Additional test will be required if it will be equipped to the
other devices
Q6062
Q6050
Heatsink
has already been certificated by FCC and IC.
Q6053
Q6060
Q6063
A201
SCREW
3TTB+8B(3BC)
x 4 pcs.
A217
A215
A223
A717
Q6055
A715
Q6065
SCREW
3TTB+8B(3CM)SR
SCREW
3TTB+8B(3BC)
x 29 pcs.
U0064
A217
A213
A203
A205
EXPLODED VIEWS-2
WiFi & Bluetooth Module has already been certificated by FCC and IC.
Information to the user.
Indicate "Contains FCC ID: TX2-RTL8273AS", "Contains IC: 6317A- RTL8273AS" and following information to the host
device installed.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Describe the following sentence to a user's manual of the host device.
[For FCC]
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
TX-NR727
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low
levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is
desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s
body (excluding extremities: hands, wrists, feet and ankles).
[For IC]
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets
RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it
deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be
installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities:
hands, wrists, feet and ankles).
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non
contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement
émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale
autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre
le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
TX-NR727/828/ DTR-40.5/50.5
SCHEMATIC DIAGRAMS-01(PART-1)
BLOCK DIAGRAM AUDIO SECTION
TX-NR727/828/ DTR-40.5/50.5
SUB1L
SUB1R
MAINL
MAINR
REC_L
REC_R
R
L
R
L
R
L
R
L
R
L
R
L
R
MAINL
MAINR
R
L
L
R
L
R
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
L
1
SBLC
SBRC
SLC
SRC
MAINL
2
1
2
1
2
2
1
MAINR
SBRELAY
Z3MUTE
Z2MUTE
PRERELAY
SBZ2MUT
AMUT
SPRL_F
SPRL_CS
SPRL_SB
SPRL_FW
SPRL_FH
SUB1 should be always ON.
ADCL
ADCR
SUB1L
SUB1R
SUB2L
SUB2R
0/-6/-12/-18dB
MIC
FRONT BOARD
MIC AMP
MIC DET
RchLch
TUNER PACK
72
82
83
DVD
33
32
54
HDMI FLR
X-Tl
MCLK
SPI
HDMI LRCK
HDMI BCK
HDMI MCK
DIR
DIR LRCK
DIR FLR
DIR BCK
DIR MCK
DIG CLK
73
BCK NET
LRCK NET
DATA NET
MCK NET
+-
LPF
+6dB
Z2NET R
47
DIG SD1
DIG SD0
DIG CLK
2ch ADC
LTAD
RTAD
53
SPI
non VLSC
VLSC
FR
Q411
Q421
Q431
non VLSC
+6dB
VLSC
Q411
Q421
Q431
FL
Z3
Z2
46
12V TRIDDER
CONTROL
12V TRIGGER A
12V TRIGGER B
12V TRIGGER C
IR OUT
IR IN
IR IN
TRANSMITTERS
RS232
FL
FR
C
*NOTICE
FL/FR -12dB
Downmix
INVERTING
SW +3.5dB
INVERTING
Q4003
35
36
44
34
45
96
97
39
93
38
92
37
40
41
94
95
42
43
90
91
(FR)
FL
(FL)
FR
CEN
(SR)
SL
(SL)
SR
(SBR)
SBL
(SBL)
SBR
98
99
100
1
4
3
2
8
6
7
10
12
11
13
14
15
17
16
18
19
20
24
23
22
Z2R
Z2L
priority terminal
TONE
TONE
AV=+20dB
SW
ex)(FR)<--->FL ,(FL)<--->FR
POWER AMPLIFIER
Z2 L
Z2 R
Z3 L
Z3 R
Zone2
Line/Preout
Line/Preout
ZONE OUT
SPI to Micom
XIN
5MHz
XOUT
FR
(FL)
(FR)
FL
SBRCIN
SWIN1
SW(DAC)
SWIN2
CIN1
C(DAC)
CIN2
FL(DAC)
FRIN2
FL(MIX)
FRIN1
FR(DAC)
FLIN1
FR(MIX)
FLIN2
SR(DAC)
SRIN1
SRIN2
SLIN1
SLIN2
SBLCIN
SBRIN2
SL(DAC)
SBLIN2
SBLIN1
SBL(DAC)
SBR(DAC)
SBRIN1
SRCIN
SLCIN
Zone2L Out
Zone2R Out
SW 80Hz LPF
FL+FR (-6dB)
-12dB/oct
PCM9211
++-
PCM1690
(FL/FR)DSP FLR
8ch DAC
(CT/SW)
(SL/SR)
(BL/BR)
DIR MCK
CX LRCK
CX SCLK
DSP SLR
DSP CSW
DSP SBLR
+-+-+-+--
LPF
LPF
LPF
+-+-
LPF
LPF
+6dB
+6dB
+6dB
+6dB
+6dB
LPF
LPF
LPF
Zone3 in(L-ch)
Zone3 in(R-ch)
0.5dB step/each VR
L
R
TONE
TONE
Z2 out(L-ch)
Z2 R Line/preout
Z3 R Line/preout
Z3 L Line/preout
Zone2 in(L-ch)
Z3 Lineout
Z2 Lineout
Ana all ch st
71
70
R
L
86
87
78
79
Buffer
XTAL-X7001
Q1004
Q1005
11.2896MHz
+-
+6dB
LPF
Z2NET L
Q1001
TC7SZU04FU
uPD70F3747
CBL/SAT
STB/DVR
GAME
PC
TV/CD
Z2 Lineout
SBR(Whole House_MODE)
C
SW
(Whole House_MODE)
SL
(Whole House_MODE)
SR
(Whole House_MODE)
(Whole House_MODE)
(Whole House)
SBL
PCM1754D
2ch DAC
Q1002
R2A15220FP
Q4001
COAX1
X1001-XTAL
DIG SDO
VMSDO
VMSDI
DIGCLK
DIGSDO
DIGSDI
VMCLK
SDI
CLK
SDO
EEPROM
Q7001
SDO
SDI
CLK
SPI
(HDMISLC)
(HDMI SDA)
MICOM
Q7009
BAAF1320
PHONO
56
57
58
59
60
61
62
63
64
65
68
74
69
75
DIR MCK
DIR FLR
DIR BCK
DIR LRCK
HDMI MCK
HDMI BCK
HDMI LRCK
HDMI FLR
ARC_SPDIF
HDMI_SPDIF
IN
(FRONT HDMI)
IN1
IN2
IN3
IN4
IN5
IN6
IN7
OUT1
OUT2
BCK NET
LRCK NET
DATA NET
MCK NET
(BL/BR)
(SL/SR)
(CT/SW)
(FL/FR)
HDMI
RX
HDMI
TX
Q3001
DSP FLR
DSP SBLR
DSP CSW
DSP SLR
CX LRCK
CX SCLK
BAHDM1357 1/1
D830K
ONLY
(DTR-50.5)
(TX-NR828)
(TX-NR727)
(DTR-40.5)
BADG1332 1/2
MJJ ONLY
MJJ ONLY
NR727/NR828
NR727/NR828
Q7401
Q4530
TX-NR727/TX-NR828
EXCEPT
(DTR-50.5 Series)
FLDSDO
(TX-NR828 Series)
FRONT
(TX-NR727 Series)
PREOUT
TX-NR727MDD MMA
EXCEPT
(TX-NR727 Series)(DTR-40.5 Series)
(DTR-50.5 Series)
SL
SR
SBL
SW2
SBR
SW1
HDMI BLOCK DIAGRAM
(DTR-50.5 Series)
(DTR-40.5 Series)
(TX-NR828 Series)
(TX-NR727 Series)
OPT2
COAX 1
COAX 2
RI
RI
INTERFACE
BADG1332 2/2 (TX-NR727)
(DTR-40.5)
(TX-NR828)
(DTR-50.5)
COAX2
COAX3
OPT1
FRONT
USB
YKF45-0029N
DATA-
DATA+
VBUS
OPT1
COAX 3
ONLY)
(TX-NR828
DTR-50.5
OPT2
OPT
Zone3
TX-NR727/TX-NR828
-6dB DownZone2/Zone3
Linout
84
85
+6dB
+6dB
+6dB-6dB
-6dB
NR727/NR828
EXECPT
NR727MDD MMA
EXECPT
ZONE FUNCTION
(SL-IN2)
(SR-OUT)
(SL-OUT)
R2A15218FP
Q4301
(SR-IN2)
(FR-OUT)
(SBR-OUT)
Z2 L Line/preout
(SBR-IN)
(SUBRC-IN)
(SUBLC-IN)
(SBL-IN)
Zone2 in(R-ch)
(FR-IN2)
(FL-IN2)
(IN-R9)
Z2 out(R-ch)
(FL-OUT)
(SBL-OUT)
FLDCLK
ML9208A
(DTR-40.5 ONLY)
Q7501
16-BT-165GINK
(IN-L9)
Rch
Rch
Rch
Rch
Rch
Lch
Lch
Lch
Lch
Lch
Rch
Lch
Rch
Rch
Lch
Lch
1.Actually the right and left in/output signal of Q4001/Q4301(R2A15220FP/R2A15218FP) is connected reversely to real signal.
FRONT LEFT
FRONT RIGHT
+29dB
+29dB
+29dB
+29dB
+29dB
CENTER
SURR. LEFT
SURR. RIGHT
RIGHT
HIGH/WIDE
LEFT
HIGH/WIDE
SUUR. BACK
+29dB
+29dB
ZONE2 LEFT
ZONE2 RIGHT
FWL
FWR
MJJ
EXCEPT
FHL
Subwoofer
SPEAKER TERMINALS
FHR
TN-NR727/DTR-40.5
EXCEPT
BATRM1335 1/1
(TX-NR727 Series)(TX-NR828 Series)
HEADPHONES
(DTR-50.5 Series)(DTR-40.5 Series)
BADG1345 1/2
BADG1345 1/2
BADG1345 1/2
BADG1345 2/2
BADG1345 2/2
BADG1345 2/2
IR
REMOTE SENSOR
TX-NR727 EXCEPT
TX-NR828 EXCEPT
(DTR-40.5 Series)
(TX-NR828 Series)
(DTR-40.5 Series)
(DTR-50.5 Series)
TX-NR828 EXCEPT
BADIS1340 3/5
BADIS1340 5/5
BADIS1350 3/5
BADIS1350 5/5
BADIS1360 3/5
BADIS1360 5/5
BADIS1350 2/5
BADIS1340 2/5 BADIS1360 2/5
(FRONT IN)
AUX IN
(TX-NR828 Series)
BADIS1350 1/5
BADIS1340 1/5
BADIS1360 1/5
TX-NR727 EXCEPT
BADIS1350 4/5
BADIS1340 4/5
BADIS1360 4/5
BADIS1330 4/4
BADIS1330 1/4
BADIS1330 2/4
BADIS1330 3/4
RS232
41
40
97
98
11
9
23
5
43
78
44
100
42
45
99
79
21
3
MODEL NO. TX-NR727/TX-NR828/DTR-40.5/DTR-50.5
BLOCK DIAGRAM (PART-1) AUDIO SECTION