One for All URC-4110 User Manual

Page 1
2
TABLE OF CONTENTS
Introduction . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting Up Your Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Searching For Your Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To Change Volume Lock To Another Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Unlocking Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Manufacturer’s Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup Codes For Cable Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup Codes For Cable Box / PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup Codes For Satellite Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup Codes For Satellite Receiver / PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . 12
Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setup Codes For VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setup Codes For PVRs (or DVRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setup Codes For TV/VCR Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setup Codes For DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setup Codes For DVD Players / VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setup Codes For TV/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setup Codes For TV/VCR/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Page 2
INTRODUCTION
The One ForAll 4 Devices Universal Remote Control is designed to operate four home entertainment devices,dependingon the model pur­chased (see
Key Charts, ModeKeys on the right).
The remotecontrolrequires twofreshAAA alkalinebatteries(not included) and easy programmingtocontrolyour devices.Forbest results,please read and performall instructions listed here.Also,keepthese instructions for future reference.
3
Page 3
FEATURES AND FUNCTIONS
UsetheKeyChartstolearnhowtouse theuniversal functionsof theOne For All 4 DevicesUniversal RemoteControl.
Key Charts
The LED (red light) blinks to show that the remote control is working and is sending signals.
Use
SET for all programming sequences.
Press POWER once to turn on or off the selected device.
Device Keys for 4 Devices:
Press VCR, DVD, TV, or CBL/SAT once to select a homeentertainment device to control.
Press
SLEEP to activate yourdevice’s sleep
timer (not availablefor all devices).
Use
TV/VID to switch the TV’s input to view TV
or video program.
Use the keypad (
0 ~ 9) to directly select chan-
nels (for example, 09 or 31).
Press ENTER once after entering channel numbers on some TV models.
Press
PREV CH once to recall the last-viewed
channel and to page back one screen on the main menu.
Press
MUTE onceto turn sound off or on.
Use MENU (or EXIT) to choose options(or exit) from your selected device’s menu or guide.
Use
CH+ (or CH -) to select the next higher(or
lower) channel.
Use VOL+ (or VOL-) to raise (or lower) the sound volume.
When controlling a DVDplayer, use SKIP FOR-
WARD
to next DVD chapter., use SKIP REVERSE
to the last DVD chapter.
Press SHIFT and use the Up/Down/Left/ Right cursor keys to move the cursor in the pro­gram guide and menu screens.
Press
SHIFT and MUTE to select a menu item.
Use the transport keys to control yourVCR, CD or DVD player,orVOD.To record a pro­gram, press the record key (
REC
) twice.
4
Page 4
INSTALLING BATTERIES
1. On the remote control’s back,push the tab and lift off the battery cover.
2. Obtain two (2) newAAA alkaline batteries.Match the + and – markson the batteries to the + and – marks in the battery case, then insert the new batteries.
3. Press the battery cover back into place.The tab should click when the cover is locked.
4. Test the unit by pressing
POWER and any mode key (e.g.,TV). If the
batteriesare inserted correctly, the LED will blink once.
NOTE:Whenbatteries needreplacement, the remote control will stopoperating. Remove the old batteries and insert new ones within30 minutes to ensureall of your programming information is restored.
Battery Precautions: Do not mix old and new batteries.•Do not mix alkaline, stan­dard (carbon-zinc)or rechargeable(nickelcadmium)batteries.•Always remove old, weakor worn-out batteries promptly and recycleordispose of them in accordance with Local and National Regulations.
SETTING UP YOUR COMPONENTS
The One ForAll 4 Devices remote control is preprogrammed at the fac­tory to operate an RCA TV and VCR, a Motorola (GI) cable box,and a Toshiba DVDplayer. To control devices other than the default brands, perform the following steps;otherwise skip this section:
NOTE: For TV/VCR Combocontrol, see the next section.
1. Turn on a device (e.g.,VCR) and,if applicable, insert media, (e.g., cassette or disc).
NOTE:Please readsteps 2-4 completely beforeproceeding.Highlight or write downthe codes and device youwishtoprogrambefore moving on to step2.
2. On the remote control,press a device key once(i.e., VCR, DVD,
TV,orCBL/SAT ). Press and hold SET until the LED blinks twice,
then release
SET.
3. Use the Manufacturer’s Codes (starting on page 12) to locate the type of device and brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice,then repeat steps 2 through 3 and try entering the same code again.
5
Page 5
4. Aim the remote control at the device and pressPOWER once.
The device shouldturn off.If it does not respond,repeat steps 2-3,trying eachcodeforyour branduntil you find one that works.If it still doesnot work,try Searching ForYour
Code.
NOTE: If the device doesnot have a POWER key, press the (PLAY) key.
5. Repeat steps 1 through 4 for each device you want to control.
PROGRAMMING TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and insert a video cassette.
NOTE: Pleaseread steps 2-4 completely beforeproceeding.Highlight or write down the codes and device you wish to programbefore moving on to step 2.
2. On the remote control,press VCR.Press and hold SET untilthe
LEDblinks twice, then release
SET.
3. Use the
Setup Codes For TV/VCR Combos (on page 13) to locate the
brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice,then repeat steps 2 through 3 and try entering the same code again.
4. Aim the remote control at the device and press POWER once.
Itshould turn off.If the devicedoesnot respond,repeat steps 2-3,trying eachcodeforyour branduntil you find one that works.If it still doesnot work,try Searching ForYour
Code.
NOTE: If the device doesnot have a POWER key, press the (PLAY) key.
PROGRAMMING TV/DVD COMBO CONTROL
Perform the following instructions to control a TV/DVD Combo:
1. Turn on your TV/DVD and insert a disc.
2. On the remote control, press
DVD.Press and hold SET until
the LED blinks twice,then release SET.
3. Use the
Setup Codes For TV/DVDCombos (on page 15) to locate the
brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.
4. Aim the remote control at yourTV/DVD and press
POWER.
Your TV/DVDshould turn off.If your original TV/DVD remote control did not have a POWER key, press PLAY.Your TV/DVD should start to play. If your TV/DVD does not respond,repeat steps 2-4,trying each code listed for your brand until youfind the one that operates your TV/DVD.
5. Your One For All 4 Devices is now programmed to operate your TV/DVD. Writeyour TV/DVD code for future reference.
Remember, if you want to use your One ForAll 4 Devices to operate your TV/DVD, press the DVD key first.
6
Page 6
SEARCHING FOR YOUR CODE
If your device does not respond to the remote control after trying all codes listed for your brand,or if yourbrand is not listed at all,try searching for your code. For example, to search for a code for your TV:
1. On the remote control,press
TV once.
2. Press and hold
SET until the LED blinks twice,thenrelease
SET.
3. Enter
9 - 9 - 1. The LED will blink twice.
4. Aim the remote control at the TV and slowly alternate
between pressing
POWER and TV.Stop when the TV turns
off.
NOTE: In the searchmode, the remote control will send IR codes fromits library to the selected device,startingwith the most popular
codefirst.
5. To lock in the code,press and hold SET until the LED blinks
twice, then release
SET.
6. To search for the codes of your other devices,repeat steps 1 through 5,but substitute the appropriate device key for the device you are searching for.
CHECKING THE CODES
If you have set up the remote control using the Searching For Your Code procedure,you may need to find out which four-digit code is operating your equipment:
For example,to find out which code is operating your TV:
1. On the remote control,press
TV once.
2. Press and hold
SET until the LED blinks twice,thenrelease
SET.
3. Enter
9 - 9 - 0.The LED will blink twice.
4. To view the code for the first digit,press
1 once.Wait 3 seconds,
count the LED blinks (e.g.,3 blinks = 3) and write down the num­ber.
NOTE: If a code digit is “0”,the LED will not blink.
5. Repeat step 4 three more times for remaining digits.Use 2 for the second digit,
3 for the third digit,and 4 for the fourth digit.
6. To check for codes of other devices,repeat steps 1 through 5, but substitute the appropriate device key for each device you are check­ing.
RE-ASSIGNING DEVICE KEYS
The One ForAll 4 Devices can be set to control a second TV,VCR,or DVDplayer.
For example,tocontrol two TVs, a VCR,and a cable box,you will need to re-assign the unused
DVD key to operate the second TV as follows:
1. On the remote control,press and hold
SET until the LED
blinks twice,then release
SET.
2. Enter
9 - 9 - 2.The LED will blink twice.
3. Press
TV once,then press DVD once.
7
Page 7
4. The DVD key is now ready to be programmed for your second TV. (See
Setting up your components.)
To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence fromthe below chart for the most popular compo­nents:
To Re-Assign Key SequencePerform
VCR as 2nd TV key: SET - 9 - 9 - 2 - TV - VCR
VCR as 2nd CBL key: SET - 9 - 9 - 2 - CBL/SAT - VCR
VCR as 2nd SAT key: SET - 9 - 9 - 2 - CBL/SAT - VCR
VCR as 2nd DVD key: SET - 9 - 9 - 2 - DVD - VCR
VCR back to VCR: SET - 9 - 9 - 2 - VCR - VCR
DVD as 2nd TV key: SET - 9 - 9 - 2 - TV - DVD
DVD as 2nd CBL key: SET - 9 - 9 - 2 - CBL/SAT - DVD
DVD as 2nd SAT key: SET - 9 - 9 - 2 - CBL/SAT - DVD
DVD as 2ndVCR key: SET - 9 - 9 - 2 - VCR - DVD
DVD back to DVD: SET - 9 - 9 - 2 - DVD - DVD
When a re-assignment is done,the LED will blink twice to confirm your choice.At that time, you will need to program the remote control for the new device (see
Setting up your components).
CHANGING VOLUME LOCK
The One ForAll 4 Devices is set to controlthe volume of your TV in the TV,VCR,CBL/SAT,and DVD modes.If you want the volume to be con­trolled by a mode other than TV (e.g.,CBL/SAT),change theVolume Lock as follows:
To Change Volume Lock To Another Mode:
1. On the remote control,press and hold SET until the LED
blinks twice,then release
SET.
2. Enter
9 - 9 - 3 and then press any mode key once (except
TV).TheLED will blink twice.
3. Now,whenever you press
VOL+, VOL–,or MUTE, volume will
be controlled by your mode choice.
Unlocking Volume Control:
NOTE: Perform these instructions when you want independent volumecontrolfor each programmed device (e.g.,TV volume control in TV mode, CBL/SAT volumecontrol in CBL/SAT mode,etc.)
1. On the remote control,press and hold SET until the LED
blinks twice,then release
SET.
2. Enter
9 - 9 - 3 and then press VOL+.The LED will blink four
times.
3. Volumewill again be controlled according to its default states.
8
Page 8
TROUBLESHOOTING
PROBLEM: If you own a satellite that uses code 0775 (Express
Vu and Echostar) and your exit key does not work, perform the following sequence to activate this fea­ture/function.
SOLUTION: 1. Press the CBL/SAT key
2. Press and hold the SET key until the red LED
blinks twice
3. Press 9-9-4,the red LED will blink twice
4. Press SET and release (one blink on LED)
5. Press 3-3-6
6. Press the EXIT key, the red LED will blink twice.
The Exit key will now correctlyperform the exit feature/function on your satellite.
PROBLEM: LED does not blink when you press a key.
SOLUTION: Replacebatterieswith four new
AAA
alkaline
batteries.
PROBLEM: LED blinks when you press a key, but home enter-
tainment component does not respond.
SOLUTION: Make sure the remote control is aimed at your home
entertainment device and is not farther than 15 feet away.
PROBLEM: The unitdoes not controlhome entertainment devices
orcommands arenot working properly.
SOLUTION: Try all listed codes for thecomponent brands being
set up. Make sure they can be operated with an infrared remote control.
PROBLEM: TV/VCR combo does not respondproperly.
SOLUTION: Use the VCR codes for your brand.Some combo
unitsmay require both a TV code and a VCR code for full operation.
PROBLEM: Changing channels does not work properly.
SOLUTION: If original remote control required pressing ENTER
to change channels,press
ENTER on the remote
control afterentering the channel number.
PROBLEM: Tried“Search Method”and still could not find a
working code.
SOLUTION: Clearthe device key as follows: Press and hold
SET
untilthe LED blinks twice,then release. Next enter 9
- 9 - 2.Then press the device key to be cleared twice. Now repeat the“Search Method.”
PROBLEM:
CH + and CH - do not work for your RCA TV.
SOLUTION: Due to RCA design (1983-1987),only the original
remote control will operate these functions.
PROBLEM: Remote controldoes not turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: Forpower on, these products require programming
TV codes.For Sony, use TV code 0000 andVCR code 0032.For Sharp, use TV code 0093 and VCR code 0048.
PROBLEM: Need additional information.
SOLUTION: • Please visit : www.oneforall.com
9
Page 9
INSTRUCTIONS TO THE USER
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide a reasonable protection against harmful interference in a residential installation.Thisequipment generates,uses,and can radiateradio frequency energy and if not installed and used in accordance with the instructions,maycause harmful interference to radio communications. However,there is no guarantee that interferencewill not occur in aparticular installation.If this equipment does cause harmful interference to radio or tel­evision reception, whichcan be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase separation between equipment and receiver.
• Connect equipmentinto an outlet or a circuit different from that to which
the receiveris connected.
• Consult dealer or experiencedradio/TV technician for help.
LIMITED LIFETIME WARRANTY
Audiovox Electronics Corporation (the“Company”) warrants to you the original retail purchaser of this product that should it, under normal use and conditions, be proven defective in material or workmanship during its lifetime while you own it,such defect(s)will be repairedor replaced (at the Company’s option) without chargeforparts and repairlabor.To obtain repairor replacement within the terms of thisWarranty, the product is to be delivered with proof of warranty coverage (e.g.dated bill of sale),specification of defect(s),transportation pre­paid,to the Company at the address shown below.ThisWarrantydoes not cover product purchased,serviced or used outside the United Statesor Canada. This Warranty is not transferable and does not extend to costs incurredforinstalla­tion,removalor reinstallationof the product. This Warranty does not apply if in the Company’s opinion,the product has been damaged through alteration, improper installation,mishandling, misuse,neglect,accident,or the simultane­ous use of different battery types (e.g.alkaline,standardor rechargeable).
THE EXTENT OF THE COMPANY’SLIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDEDABOVE AND,IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
ThisWarranty is in lieu of all other express warranties or liabilities.ANY IMPLIED WARRANTIES,INCLUDINGANY IMPLIEDWARRANTY OF MER­CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIM­ITED TO DURATION OF THISWARRANTY.IN NO CASE SHALL THE COMPA­NY BE LIABLE FORANYCONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.No person or representative is authorized to assumeforthe Companyanyliability other than expressedherein in connection with the sale of this product.Some states/provinces do not allowlimitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequen­tial damage so the above limitationsor exclusions may not applyto you. ThisWarranty gives you specific legal rights and you may also have other rights,which vary fromstate/province to state/province.U.S.A.:Audiovox Electronics Corporation,150 Marcus Blvd., Hauppauge,New York 11788 CANA­DA: AudiovoxReturn Center, c/o Genco,6685 Kennedy Road,Unit 3,Door 16, Mississauga,OntarioL5T 3A5
10
Page 10
ADDITIONAL INFORMATION
ONE FOR ALL® is the registered trademark of Universal Electronics Inc.
Audiovox Accessories Corporation isthe Licensee of the ONE FORALL®
brand for North America.
Copyright 2006 by Universal Electronics Inc. No part of this publication may be reproduced,transmitted,transcribed,stored in any retrieval system,or translated to any language,in any form or by any means, electronic,mechanical,magnetic,optical,manual, or otherwise,without the prior written permission of Universal Electronics Inc.
OneForAll®4 Devices is compatibilefor use in NorthAmericaexcluding Mexico.
URC-4110 07/08
11
Page 11
12
MANUFACTURER’S CODES
Setup Codes for Cable Boxes
ABC 0003,0008
Americast 0899
Bell South 0899
Digeo 1187
GeneralInstrument 0003,0276
Jerrold 0003,0276
Memorex 0000
Motorola 0276, 1187,1376
Pace 0008,1877
Panasonic 0000
Paragon 0000
Pioneer 0533,1877
Pulsar 0000
Quasar 0000
Runco 0000
ScientificAtlanta 0008,1877
Starcom 0003
Supercable 0276
Torx 0003
Toshiba 0000
Zenith 0000, 0899
Setup Codes for Cable Box/PVR (or DVR) Combos
Setup Codes for Satellite Receivers
DirecTV 1377,0099, 0247,0392, 0566,
0639,0724, 0749,0819, 1076, 1108,1142,1392,1442, 1609, 1639,1640, 1749,1856
Dish Network 0775
DishNetwork System 0775,1005, 1505,1775
Dishpro 0775, 1005,1505, 1775
Echostar 0775, 1005,1505, 1775
Expressvu 0775,1775
GE 0392,0566
GeneralInstrument 0869
GOI 0775, 1775
Hisense 1535
Hitachi 0819
HTS 0775,1775
Hughes 0749,1442, 1749
Hughes Network Systems 0749,1142, 1442,1749
iLo 1535
Jerrold 0869
JVC 0775,1775
Magnavox 0724
Memorex 0724
Mitsubishi 0749
Motorola 0856, 0869
NextLevel 0869
Panasonic 0247,0701
Paysat 0724
Philips 0099,0724, 0749,0819, 1076,
1142,1442, 1749
Pioneer 442
Proscan 0392,0566
Proton 1535
RadioShack 0869
RCA 0392, 0566,0855, 1392
Samsung 1108,1142, 1276,1377, 1442,
1609
Sony 0639,1639, 1640
Star Choice 0869
Tivo 1142, 1442
Toshiba 0749,0790,0819,1285,1749
UltimateTV 1392,1640
Uniden 0724
US Digital 1535
USDTV 1535
Voom 0869
Zenith 1856
Americast 0899
Digeo 1187
Motorola 1376, 1187
Pace 1877
Pioneer 1877
ScientificAtlanta 1877
Zenith 0899
DirecTV 1377,0099, 0392,0639,
1076,1142, 1392,1442,1640
DishNetwork System 0775,1505
Dishpro 0775, 1505
Echostar 0775, 1505
Expressvu 0775
Hughes Network Systems 1142,1442
Motorola 0869
Philips 1142,1442
Proscan 0392
RCA 1392
Samsung 1442
Sony 0639,1640
Star Choice 0869
continued on next page...
Setup Codes for Satellite Receiver/PVR (or DVR) Combos
Page 12
13
MANUFACTURER’S CODES
Setup Codes for TVs
Admiral 0093,0463
Advent 0761,0783, 0815,0817, 0842
Aiko 0092
Akai 0030,0060,0672,0702,0812
AmericaAction 0180
Anam 0180
AOC 0030
ApexDigital 0156,0748, 0765,0767, 0879
Audiovox 0092, 0180,0451
Aventura 0171
Bell & Howell 0154
Bradford 0180
Broksonic 0180,0236, 0463
Candle 0030
Carnivale 0030
Carver 0054
Celebrity 0000
Celera 0765
Changhong 0765
Citizen 0030,0060, 0092
Clarion 0180
CommercialSolutions 0047
Contec 0180
Craig 0180
Crosley 0054
Crown 0180
CurtisMathes 0030,0047,0054,0060,0093,
0145,0154, 0166,0451, 0702
CXC 0180
Daewoo 0092,0451, 0672,1661
Denon 0145
DiamondVision 1996,1997
Dumont 0017
Durabrand 0171,0178, 0180,0463, 1034
Dwin 0093
Electroband 0000
Electrograph 1755
Emerson 0154, 0171,0178, 0180,0236,
0451,0463, 1944,1963
Envision 0030
ESA 0171,0812
Fisher 0154
Funai 0171,0180
Futuretech 0180
Gateway 1755,1756
GE 0047,0051, 0178,0451
Gibralter 0017,0030
GoldStar 0030, 0178
Grunpy 0180
Haier 1034
Hallmark 0178
Harman/Kardon 0054
Harvard 0180
Havermy 0093
Hello Kitty 0451
Hisense 0748
Hitachi 0145
iLo 1286
Infinity 0054
Insignia 1204
Inteq 0017
JBL 0054
JCB 0000
Jensen 0761,0815, 0817
JVC 0053
KEC 0180
Kenwood 0030
KLH 0765, 0767
KTV 0030,0180
LG 0178,1265
LXI 0047,0054, 0154,0156, 0178
Magnavox 0030,0054, 1944,1963
Marantz 0030, 0054
Matsushita 0250
Maxent 1755
Megatron 0145, 0178
Memorex 0150,0154, 0178,0463
MGA 0030,0150,0178
Midland 0017,0047,0051
Mitsubishi 0093,0150, 0178,1250
Motorola 0093
MTC 0030,0060
Multitech 0180
NAD 0156,0178
NEC 0030
NetTV 1755
Nikko 0030,0092, 0178
Norcent 0748
Norwood Micro 1286
NTC 0092
Onwa 0180
Optimus 0154,0166,0250
Optonica 0093,0165
Orion 0236,0463
Panasonic 0051,0250
Penney 0030,0047, 0051,0060, 0156,
0178
Philco 0030,0054
Philips 0054,0690
Pilot 0030
Pioneer 0166,0679
Polaroid 0765
Portland 0092
Prima 0761,0783, 0815,0817
Prism 0051
Proscan 0047
Proton 0178
Pulsar 0017
Quasar 0051,0165, 0250
RadioShack 0030, 0047,0154, 0165,0178,
0180
RCA 0047, 0090,0679
Realistic 0030,0154,0165,0178,0180
Runco 0017,0030
Sampo 0030, 1755
Samsung 0030,0060, 0178,0702, 0812
Sansui 0463
Sanyo 0154
Page 13
14
Scotch 0178
Scott 0178,0180,0236
Sears 0047, 0054,0154,0156, 0171,
0178
Sharp 0093, 0165
ShengChia 0093
Sony 0000
Soundesign 0178,0180
Squareview 0171
SSS 0180
Starlite 0180
Superscan 0093
Supreme 0000
SVA 0748
Sylvania 0030, 0054,0171, 1944,1963
Symphonic 0171,0180
Tandy 0093
Tatung 1286,1756
Technics 0051,0250
Techwood 0051
Teknika 0054, 0060,0092, 0150,0180
Telefunken 0702
TMK 0178
TNCi 0017
Toshiba 0060,0154,0156,1265
TVS 0463
US Logic 1286
Vector Research 0030
Victor 0053
Vidikron 0054
Vidtech 0178
Viewsonic 1755
Vizio 1756
Wards 0030,0054, 0165,0178
Waycon 0156
Westinghouse 0000,0451
White Westinghouse 0463
Yamaha 0030
Zenith 0017, 0092,0178, 0463,1265
ABS 1972
Admiral 0048,0209
Adventura 0000
Aiwa 0000, 0037
Alienware 1972
American High 0035
Asha 0240
Audiovox 0037
Beaumark 0240
Bell & Howell 0104
Broksonic 0121,0184, 0209,1479
Calix 0037
Canon 0035
Carver 0081
CCE 0072
Citizen 0037,1278
Colt 0072
Craig 0037,0047, 0072,0240
CurtisMathes 0035,0060,0162,1035
Cybernex 0240
CyberPower 1972
Daewoo 0045,1278
Dell 1972
Denon 0042
DirecTV 0739
Durabrand 0039
Dynatech 0000
Electrohome 0037, 0043
Electrophonic 0037
Emerex 0032
Emerson 0000, 0037,0043, 0121,0184,
0209,0593, 1278,1479, 1593
Fisher 0047,0104
Fuji 0035
Funai 0000,0593,1593
Garrard 0000
Gateway 1972
GE 0035,0060, 0240,0807, 1035,
1060
GoVideo 0240
GoldStar 0037, 1237
Gradiente 0000
Harley Davidson 0000
Harman/Kardon 0081
Harwood 0072
Hewlett Packard 1972
HI-Q 0047
Hitachi 0000,0042
Howard Computers 1972
HP 1972
Hughes Network Systems 0042,0739
Humax 0739
Hush 1972
iBUYPOWER 1972
JVC 0067
KEC 0037
Kenwood 0067
KLH 0072
Kodak 0035,0037
Linksys 1972
Lloyd's 0000
Logik 0072
LXI 0037
Magnasonic 0593,1278
Magnavox 0000,0035, 0039,0081, 0593
Magnin 0240
Marantz 0035, 0081
Marta 0037
Matsushita 0035, 0162
MediaCenter PC 1972
MEI 0035
Memorex 0000,0035, 0037,0039, 0047,
0048,0104, 0162,0209, 0240, 1237
MGA 0043,0240
MGN Technology 0240
Microsoft 1972
Mind 1972
continued on next page...
Setup Codes For VCRs
Page 14
15
Setup Codes for PVRs (or DVRs)
Minolta 0042
Mitsubishi 0043,0067, 0807
Motorola 0035, 0048
MTC 0000,0240
Multitech 0000, 0072
NEC 0067,0104
Nikko 0037
Niveus Media 1972
Noblex 0240
Northgate 1972
Olympus 0035
Optimus 0037,0048,0104,0162,0593,
1062
Orion 0184,0209, 1479
Panasonic 0035,0162, 0616,1035, 1062
Penney 0035,0037, 0042,0240, 1035,
1237
Pentax 0042
Philco 0035
Philips 0035,0081, 0618,0739
Pilot 0037
Pioneer 0067
PolkAudio 0081
Presidian 1593
Profitronic 0240
Proscan 0060,1060
Protec 0072
Pulsar 0039
Quasar 0035,0162, 1035
RadioShack 0000
Radix 0037
Randex 0037
RCA 0042, 0060,0240, 0807,0880,
1035,1060
Realistic 0000,0035,0037,0047,0048,
0104
ReplayTV 0614,0616
Ricavision 1972
Runco 0039
Samsung 0045,0240, 0739,1014
Sanky 0039,0048
Sansui 0000,0067, 0209,1479
Sanyo 0047,0104, 0240
Scott 0043,0045,0121,0184
Sears 0000, 0035,0037,0042, 0047,
0104,1237
Sharp 0048, 0807
Shintom 0072
Shogun 0240
Singer 0072
SonicBlue 0614, 0616
Sony 0000,0032, 0035,0636, 1232,
1972
Stack9 1972
STS 0042
Sylvania 0000, 0035,0043, 0081,0593,
1593
Symphonic 0000,0593, 1593
Systemax 1972
Tagar Systems 1972
Teac 0000
Technics 0035,0162
Teknika 0000, 0035,0037
Thomas 0000
Tivo 0618, 0636,0739
TMK 0240
Toshiba 0043,0045,0209,0845,1008,
1145,1972, 1503
Totevision 0037, 0240
Touch 1972
Unitech 0240
Vector 0045
Video Concepts 0045
Videomagic 0037
Videosonic 0240
Viewsonic 1972
Villain 0000
Voodoo 1972
Wards 0000,0035, 0042,0047, 0048,
0060,0072, 0081,0240
White Westinghouse 0072,0209
XR-1000 0000, 0035,0072
Zenith 0000, 0039,0209, 1479
ZT Group 1972
MANUFACTURER’S CODES
Setup Codes for VCRs (continues)
ABS 1972
Alienware 1972
CyberPower 1972
Dell 1972
DirecTV 0739
Gateway 1972
Hewlett Packard 1972
Howard Computers 1972
HP 1972
Hughes Network Systems 0739
Humax 0739
Hush 1972
iBUYPOWER 1972
Linksys 1972
MediaCenter PC 1972
Microsoft 1972
Mind 1972
Niveus Media 1972
Northgate 1972
Panasonic 0616
Philips 0618,0739
RCA 0880
ReplayTV 0614,0616
Samsung 0739
SonicBlue 0614, 0616
Sony 0636,1972
Stack9 1972
Systemax 1972
Tagar Systems 1972
Tivo 0618, 0636,0739
Page 15
16
Toshiba 1008,1972
Touch 1972
Viewsonic 1972
Voodoo 1972
ZT Group 1972
Setup Codes For TV/VCR Combos
Broksonic 1479
Citizen 1278
Colt 0072
CurtisMathes 1035
Daewoo 1278
Emerson 0593, 1278,1479
Funai 0000
GE 0240,0807, 1035,1060
GoldStar 1237
Harley Davidson 0000
Hitachi 0000
Lloyd's 0000
Magnasonic 0593,1278
Magnavox 0000,0593
Magnin 0240
Memorex 0162,1237
MGA 0240
Mitsubishi 0807
Optimus 0162,0593
Orion 1479
Panasonic 0162,1035
Penney 0240,1035, 1237
Quasar 0162,1035
RadioShack 0000
RCA 0240, 0807,1035, 1060
Samsung 1014
Sansui 0000,1479
Sanyo 0240
Sears 0000, 1237
Sony 0000,1232
Symphonic 0000,0593
Thomas 0000
Toshiba 0845,1145
Zenith 0000, 1479
Setup Codes for DVD Players
Akai 0695,0899
Alco 0790
ApexDigital 0672,0717, 0755,0794, 0796,
0830,1020, 1056,1061
Aspire Digital 1168
Audiovox 0790
Blaupunkt 0717
BlueParade 0571
Broksonic 0695
California AudioLabs 0490
Citizen 1277
CyberHome 1129
Daewoo 1169,1172
Denon 0490
DiamondVision 1316,1609, 1610
Disney 0675, 1270
Durabrand 1127
DVD2000 0521
Emerson 0675, 0821,1268
Funai 0675,1268,1334
Gateway 1073,1158
GE 0522,0717
GoVideo 0741,0744, 1044,1075, 1158,
1304,1730
GoldStar 0741
Gradiente 0490
Greenhill 0717
Grundig 0539
Hitachi 0573,1247
Hiteker 0672
iLo 1348, 1472
Initial 0717,1472
Insignia 1830
Integra 0571,0627
JVC 0558,0623,0867,1164
Kawasaki 0790
Kenwood 0490
KLH 0717, 0790,1020, 1149
Lecson 1533
Lenoxx 1127,1938
LG 0741
LiteOn 1158, 1416,1440
Magnavox 0503,0539, 0646,0675, 0821,
1268
Marantz 0539
McIntosh 1533
Memorex 0695,1270
Microsoft 0522
Mintek 0717,1472
Mitsubishi 0521,1521
NAD 0741
Nesa 0717
NexxTech 1402, 1830
Norcent 1830
Onkyo 0503,0627
Panasonic 0490,0503, 0703,1362, 1462,
1490,1762
Philips 0503,0539, 0646,0675, 1260,
1267,1354
Pioneer 0525,0571
Polaroid 1020,1061, 1316
PolkAudio 0539
Presidian 0675
Proceed 0672
Proscan 0522
RCA 0522, 0571,0717, 0790,0822,
1022,1132
Regent 1938
Rotel 0623
Samsung 0490,0573, 0744,0820, 0899,
1044,1075
Sansui 0695
Sanyo 0695
SensoryScience 1158
Sharp 0630, 0675,1256
continued on next page...
Page 16
17
Setup Codes For DVD Player/VCR Combos
Setup Codes For TV/DVD Player Combos
ApexDigital 1061
Broksonic 0695
Emerson 0675
Funai 0675
GoVideo 0741,0744, 1044,1075
GoldStar 0741
JVC 0867,1164
LG 0741
Memorex 0695
Panasonic 1762
Philips 0675,1267
Polaroid 1061
Presidian 0675
RCA 0522, 0822
Samsung 0820,1044, 1075
Sansui 0695
Sharp 0630
Sony 0864,1033, 1431
Sylvania 0675
Symphonic 0675
Toshiba 0503
Zenith 0741
Akai 0695
ApexDigital 0830
Broksonic 0695
DiamondVision 1610
Emerson 0675, 1268
Hitachi 1247
iLo 1472
Initial 1472
Magnavox 1268
Mintek 1472
Panasonic 1490
Philips 1260
RCA 1022
Samsung 0899
Sansui 0695
Sylvania 0675, 1268
Toshiba 0695
Setup Codes For TV/VCR/DVD Player Combos
Akai 0899
DiamondVision 1609
Emerson 0821
Funai 1334
Magnavox 0821
Panasonic 1362,1462
RCA 1132
Sharp 0630
Superscan 0821
Sylvania 0821
Toshiba 1045
MANUFACTURER’S CODES
Setup Codes for DVD Players (continues)
Shinsonic 0533
Sony 0533,0864, 1033,1431, 1533
Superscan 0821
Sylvania 0675, 0821,1268
Symphonic 0675,1268
Teac 0790
Technics 0490,0703
ThetaDigital 0571
Toshiba 0503,0695,1045,1154
Urban Concepts 0503
Venturer 0790
Xbox 0522
Yamaha 0490,0539
Zenith 0503, 0741
Loading...