NSC 5962-9950701QLA, 5962-9950701QKA Datasheet
54LVX3384
10-Bit Low Power Bus Switch
General Description
The 54LVX3384 provides 10 bits of high-speed CMOS
TTL-compatible bus switches. The low on resistance of the
switch allowsinputs to be connected to outputs without adding propagation delay or generating additional ground
bounce noise. The device is organized as two 5-bit switches
with separate bus enable (OE ) signals. When OE is low,the
switch is on and port A is connected to port B. When OE is
high, the switch is open and a high-impedance state exists
between the two ports.
Features
n 4Ω switch connection between two ports
n Minimal propagation delay through the switch
n Ultra low power with
<
0.1 µA typical I
CC
n Zero ground bounce in flow-through mode
n Control inputs compatible with TTL levels
n Available in CDIP and Cerpack Packaging
n Standard Microcircuit Drawing (SMD) 5962-9950701
Ordering Code
Order Number Package Number Package Description
54LVX3384J-QML J24F 24-Lead Ceramic Dual-in-line
54LVX3384W-QML W24C 24-Lead Cerpack
Logic Diagram
Pin Descriptions
Pin Names Description
OEA, OEB
Bus Switch Enable
A
0–A9
Bus A
B
0–B9
Bus B
Connection Diagram
Truth Table
OEA OEB B0–B
4
B5–B
9
Function
LLA
0–A4
A5–A
9
Connect
LHA
0–A4
HIGH-Z
State
Connect
H L HIGH-Z
State
A
5–A9
Connect
H H HIGH-Z
State
HIGH-Z
State
Disconnect
DS101061-1
Pin Assignment for
CDIP and Cerpack
DS101061-2
April 1999
54LVX3384 10-Bit Low Power Bus Switch
© 1999 National Semiconductor Corporation DS101061 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (V
CC
) -0.5V to +7.0V
DC Switch Voltage (V
S
) −0.5V to +7.0V
DC Input Voltage (V
IN
) (Note 2) −0.5V to +7.0V
DC Input Diode Current (I
IK)VIN
<
0V −20 mA
DC Output (I
OUT
) Sink Current 100 mA
Storage Temperature Range (T
STG
) −65˚C to +150˚C
Power Dissapation 500mW
Junction Temperature (T
J
) 175˚C
Recommended Operating
Conditions
(Note 3)
Power Supply Operating (V
CC
) 4.5V to 5.5V
Input Voltage (V
IN
) 0V to 5.5V
Input Rise and Fall Time (t
r,tf
)
Switch Control Input 0nS/V to 5nS/V
Switch I/O 0nS/V to DC
Free Air Operating Temperature (T
A
) −55˚C to +125˚C
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the “Electrical Characteristics” table are not guaranteed at the absolute maximum ratings. The
“Recommended Operating Conditions” table will define the conditions for actual device operation.
Note 2: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 3: Unused control inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
Symbol Parameter
V
CC
(V)
T
A
=
−55˚C to
+125˚C
Units Condition
Min Max
V
IC
Clamp Diode Voltage 4.5 −1.2 V I
IN
=
− 18mA
V
IH
High Level Input Voltage 4.5-5.5 2.0 V
V
IL
Low Level Input Voltage 4.5-5.5 0.8 V
I
I
Input Leakage Current 5.5
±
1.0 µA 0 ≤ VIN≤ 5.5V
I
OZ
TRI-STATE Leakage Current 5.5
±
10.0 µA 0 ≤ A, B ≤ V
CC
R
ON
Switch On Resistance
(Note 4)
4.5 10 Ω V
IN
=
0V, I
IN
=
30mA
4.5 20 Ω V
IN
=
0V, I
IN
=
15mA
I
CC
Quiescent Supply Current 5.5 10 µA V
IN
=
V
CC
or GND, I
OUT
=
0
∆ I
CC
Increase in Iccper Input 5.5 2.5 mA One input at 3.4V
Other inputs at V
CC
or GND
I
OFF
Power Off Leakage Current 0.0 10 µA VIN= 5.5V or 0.0V
I
OS
Short Circuit Output Current
(Note 5)
4.5 80 mA VIN= 4.5V, V
OUT
= 0.0V
Note 4: Measured by voltage drop betweenAandBpinatindicated current through the switch. On resistance is determined by the lower of the voltages on the two
(A or B) pins.
Note 5: Not more than one output tested at a time.
www.national.com 2
Loading...