NorthStar Navigation Explorer 710 VHF User Manual

Explorer 710 VHF

VHF Marine Radio

Operation and Installation Manual

www.northstarnav.com

IMPORTANT SAFETY INFORMATION

Please read carefully before installation and use.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards, Obey all safety messages that follow this symbol to avoid possible injury or death.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury

CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

DISCLAIMER: It is the owner’s sole responsibility to install and use the instrument and transducers in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.

BRUNSWICK NEW TECHNOLOGIES INC. AND ITS SUBSIDIARIES AND AFFILIATES DISCLAIM ALL LIABILIT Y FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.

Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or

has been translated from, another language (Translation). In the event of any conf lict between any Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation.

This manual represents the Explorer 710 as at the time of printing. Brunswick New Technologies Inc. and its subsidiaries and affiliates reserve the right to make changes to specifications without notice.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an output on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced technician for help.

A shielded cable must be used when connecting a peripheral to the serial ports.

2 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

Contents

Secti on 1 - General Infor mation ............................................................................................................... 5

1-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1-2 Customizing your Northstar VHF Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1-3 How to Display and Navigate Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

1-4 How to Enter Alphanumeric Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1-5 LCD Symbols and Meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1-6 Basic Operation and Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Secti on 2 - The Radio Menu (MENU)

2-1 Radio Menu Options (Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2-2 Maintain Your Buddy List (BUDDY LIST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2-3 Local or Distance Sensitivity (LOCAL/DIST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

2-4 Backlighting (BACKLIGHT) and Contrast (CONTRAST) . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

2-5 GPS Data and Time (GPS/DATA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

2-6 GPS Simulator (SIMULATOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2-7 Reset to Factory Defaults (RESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Secti on 3 - Radio Setup Menu (R ADIO SETUP) ........................................................................................... 18

3-1 Radio Setup Menu (RADIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

3-2 Channel Names (CH NAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3-3 RING & BEEP Volume (RING VOL) and (BEEP VOL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3-4 Internal Speaker Connections (INT SPEAKER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3-5 Set the Priority Channel (WATCH MODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3-6 Weather Alert (Wx ALERT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

3-7 NMEA protocol (COM PORT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Secti on 4 - DSC Setup Menu (DSC SETUP) .................................................................................................. 21

4-1 DSC Setup - Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4-2 Enter Your USER MMSID (USER MMSID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4-3 Maintain Your Groups (GROUP SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

4-4 Response to Individual Calls (INDIV REPLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4-5 ATIS MMSID & ATIS Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4-6 DSC functionality options (DSC FUNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4-7 Response Type to LL Polling Calls (LL REPLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Secti on 5 - Sending and Rece iving DSC Calls ............................................................................................. 26

5-1 WHAT IS DSC? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5-2 Sending DSC calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

5-3 Receiving DSC Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

..............................................................................................11

3Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

Secti on 6 - Distress Cal ls .......................................................................................................................... 32

6-1 Sending a Distress Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6-2 Receiving a Distress Call (DISTRESS!) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

6-3 Distress Acknowledgement (distress ack) or Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Append ix A - Tec hnical Speci fications ......................................................................................................34

Append ix B - Tr oubleshooti ng ................................................................................................................. 36

Append ix C - VHF Marine Channe l Charts ................................................................................................. 37

Append ix D - MMSID and License Info rmation ......................................................................................... 49

Secti on 7 - Installatio n Section ...............................................................................................................50

RF Emissions Notice:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device’s antenna must be installed in accordance with provided instructions; and it must be operated with minimum 96 cm spacing between the antennas and all person’s body (excluding extremities of hands, wrist and feet) during operation. Further, this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

IMPORTANT:

1. Some features described in this manual are not available on every model. In particular, DSC functions are NOT available.

2. DSC functions will not operate on the 710US or the 710EU until your MMSID has been entered. Refer to section 4.2 for details.

3. The radio channels installed into the Northstar VHF radio may vary from country to country, depending upon the model, and government or national communications authority regulations.

4. Northstar NZ Ltd recommends that you check the radio operating licensing requirements of your country before using the Northstar VHF radio. The operator is solely responsible for observing proper radio installation and usage practices.

5. A DSC warning label is supplied with the 710US. To comply with FCC regulations, this label must be aﬃ xed in a location that is clearly visible from the operating controls of this radio. Make sure that the chosen location is clean and dry before applying this label.

4 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

Section 1 - General Information

1-1 Fea tur es

Congratulations on your purchase of a Northstar VHF 710US, or 710EU marine band VHF radio. All of these models provide the following useful features:

• Prominent channel display

• Adjustable contrast set tings for the LCD

• Adjustable keypad backlighting for easy night-time use

• Waterproof and submersible to comply with JIS-7

• GPS latitude and longitude (LL) and time display (when connected to a GPS)

• Choice of High or Low (25 W or 1 W) transmission power

• Top centred PTT button for comfortable left- or right-handed use

• Powerful 4 W external audio output

• Access to all currently-available marine VHF channel banks (USA, Canada, International) including weather channels where available

• Special CH16 or CH16/9 key for quick access to the priority (international distress) channel

• Special 3CH key to select your three favourite channels

• PSCAN (similar to dual watch) facilit y

In addition, the VHF 710 US/EU models also provide:

• DSC (Digital Select Calling) capability that meets USCG SC101 and Class D Standards. 710US only.

• DSC (Digital Select Calling) capability that meets EC Class D Standards. VHF 710EU only.

• DISTRESS call button to automatically transmit the MMSID and position until an acknowledgement is received

• Easy access to a buddy list of up to 20 favourite people

• MMSID storage for three favourite groups

• Group Call and All Ships Call facility

• LL position polling information

• Weather alert facility. VHF 710US only.

• ATIS facility for inland water ways. VHF 710EU only.

1-2 Customizi ng your Northstar VHF Radio

You can customize the radio to suit your individual preferences. Some preferences can be set directly through the keys as explained in this Section.

Other preferences are set up through the built-in menus and these are explained in the other Sections.

Note: VHF 710CAN operation is the same as VHF 710US. technical and DSC speciﬁ cations for VHF 710CAN are the same as VHF 710EU

5Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

1-3 How to Display and Navigate Me nus

1. Hold down MENU (or CALL /MENU). Note that only four menu items can be displayed at any one time on the screen.

2. Press + CH - to scroll up and down the menu until the cursor is positioned at the desired option. Press ENT to display that option.

3. Make any entries or changes as explained in the following section.

4. Press ENT to confirm changes. O therwise, press ESC to keep the original entry.

5. Press ESC to backup one screen or exit. Any changes are active as soon as you exit the screen.

1-4 How to Enter Alpha numeric Data

If your radio does not have the optional alphanumeric microphone, use the + CH - key to enter alphanumeric data.

Press - to count through numbers, or hold down to scroll rapidly to the desired number.

Press + to step through the alphabet, or hold down to scroll rapidly to the desired character.

If you make an error, press - until < is displayed, then press ENT to backup and correct the entry.

1-5 LCD Symbols an d Meanings

This simulation shows the locations of all the following information symbols:

6 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

Symbol Meaning

TX Transmitting.

HI LO Transmission power. High (HI) 25 W or Low (LO) 1 W.

WX Weather channel.

WX ALT Weather Alert. Alarm beeps will sound. VHF 710US only.

BUSY Receiver busy with an incoming signal.

PRI Priority channel is selected.

D Duplex operation. Otherwise, blank for Simplex operation.

LOCAL Local calling is selected. Otherwise, blank for distance calling.

DSC DSC capability is available. VHF 710US and VHF 710EU only.

Indicates an incoming DSC call, or blinks to notify you of any unread Call Log

messages

Low Battery warning (activates at 10.5 V)

88 Channel selected.

USA INT CAN Selected channel bank for VHF radio operations and regulations.

X Channel is temporarily deleted from the ALL SCAN operation.

B A Channel suﬃ x, if applicable.

CH1 CH2 CH3 Shows which of the 3 favourite channels, if any, are selected.

Otherwise blank.

ATIS Enabled for use in European inland waterways. Otherwise blank.

VHF 710EU only.

A typical operational display is shown here.

The latitude and longitude of the vessel and the local time are shown.

A transmission on Channel 16 is being made at high power using the International channel bank.

Channel 16 is set as the Priority channel. It is also set as favourite channel 1.

There is an incoming DSC call so the receiver is busy.

7Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

1-6 Basic Opera tion and Key Functions

All possible keys and their functions are listed. Note that some of the keys are not available depending on your Northstar VHF radio model.

Key Function

VOL/PWR Volume and Power. Turn clockwise to power on. Continue to turn until a comfortable

SQL Squelch or Threshold Level. Sets the threshold level for the minimum receiver

In areas of high noise (eg close to large cities) reception may improve if sensitivity

16/9 Priority Channel. VHF 710US only. Also on the microphone. Press to cancel all other

The default is Channel 16. To mak e Channel 09 the priority channel, hold down 16/9

16 Priority Channel. VHF 710EU. Also on the microphone. Press to cancel all other

WX Weather Channel. VHF 710US. In USA and Canadian waters, press to hear the most

Press + or - to change to a diﬀ erent weather channel. Press WX again to return to

If the weather alert mode (ALT) is ON and an alert tone of 1050H z is broadcast from

volume is reached. VOL/PWR will also adjust the settings of an external speaker, if connected.

signal. Turn fully counterclockwise until random noise is heard, then turn slowly clockwise until the random noise disappears. Make another 1/4 turn clockwise for best reception in open sea conditions.

is reduced. Either turn SQL slowly clockwise or use the LOCAL setting. See section

2.3.

modes and to tune into the priority channel. Press again to return to your original channel.

until a beep sounds and 09 is displayed.

modes and to tune into the priority channel, Channel 16, on high power. Press again to return to your original channel.

recently selected weather station. The WX symbol is displayed on the LCD.

the most recent channel.

the weather station, it is picked up automatically and the alarm sounds. Press any key to hear the weather alert voice message.

8 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

H/L Transmission Power. High (HI) 25 W or Low (LO) 1 W. Press to toggle between high

or low transmission power for the entire channel bank. The HI or LO selection is shown on the LCD.

Some channels allow only low power transmissions. Error beeps will sound if the

power transmission setting is incorrect.

Some channels allow only low power transmissions initially, but can be changed

to high power by holding down H/L and PTT at the same time. See Appendix C for a complete listing of channel charts.

3CH Three Favourite Channels. Also on the microphone. Press to toggle between your

favourite channels. The CH1, CH2, or CH3 symbol appears on the LCD to show which favourite channel is selected.

To scan only one of your favourite channels, press 3CH then immediately press

and release SCAN. If you want to scan all three favourite channels, press 3CH then immediately press and hold SCAN.

To add a favourite channel for the ﬁ rst time, select that channel then hold 3CH

to store it in the CH1 location. Repeat the procedure to store two more favourite channels in the CH2 and CH3 locations respectively.

If you try and add another favourite channel it will overwrite the existing CH3. CH1

and CH2 remain unless you delete them.

To delete a favourite channel, select that channel then hold down 3CH until the

CH1, CH2 or CH3 symbol disappears oﬀ the LCD.

UIC Channel Bank. 710US only. Press to toggle between USA, International or Canadian

channel banks. The selected channel bank is displayed on the LCD along with the last used channel. All the channel charts are shown in Appendix C.

U/I Channel Bank. Press to toggle between channel banks. Note that the channel banks

available are dependent upon your VHF radio model. The selected channel bank is displayed on the LCD along with the last used channel. All the channel charts are shown in Appendix C.

DIM Backlighting. 710EU only. Press to toggle between the backlighting settings. OFF

will extinguish all the backlighting except for the DISTRESS key. (Otherwise, use the menu to change the backlight setting.)

SCAN Scan. Press to scan between your current channel and the priority channel in DUAL

or TRI WATCH mode. The weather channel is also scanned if the USA channel bank is selected and the weather alert mode (ALT) is ON.

Hold down SCAN to enter ALL SCAN mode where the priority channel is checked

every 1.5 seconds.

When a signal is received, scanning stops at that channel and BUSY appears on the

screen. If the signal ceases for more than 5 seconds, the scan restarts.

Press ENT to temporarily skip over (lock out) an “always busy” channel when in ALL

SCAN mode and resume the scan. An X is shown on the screen to designate a skipped channel. Note that it is not possible to skip over the priority channel.

Press SCAN to stop at the current channel.

+ CH - Channel Select. Also on the microphone. The current channel is shown on the screen

in BIG digits with an appropriate designator suﬃ x A or B in small letters below the channel number.

9Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

Press + or - to step through the available channels one at a time, or hold down

to scroll rapidly through all the available channels. See Appendix C for a listing of channel charts.

Alphanumeric Entry. This key can also be used for menu selection and for alpha-

numeric entry. Press + or - to scroll the cursor up or down menu options when navigating menus.

When editing an item containing only numbers, press - to count through the

numbers or hold down to scroll rapidly.

To enter a character, press + to step through the alphabet or hold down to scroll

rapidly.

ENT Enter. Use ENT when navigating menus, to conﬁ rm entries and edits.

ESC Escape. Use ESC when navigating menus, to clear incorrect entries, to exit from a

menu without saving changes, and to back up to the previous screen.

CALL/MENU DSC Setup Menu and DSC Call Menu. 710US and 710EU only. Press to enter the DSC

Call Menu and make DSC calls. See Section 5.

Hold down to enter MENU SELECT. Scroll to DSC SETUP to setup your MMSID and

other DSC information. Go to RADIO SETUP to customize your Northstar VHF radio. See Section 4.

MENU Radio menu. 7000 only. Press to enter the Radio Menu and customize your Northstar

VHF radio. See Section 3.

DISTRESS Send DSC Distress Call. 710US & 710EU only. See Section 6.

PTT Press To Talk. Press PTT to transmit at any time on an allowable channel. This auto-

matically exits you from menu mode and stops scanning. You must release PTT to receive a signal.

If PT T sticks, a built-in timer will automatically shut down a transmission after ﬁ ve

minutes and sound the error beeps.

This time out is required by FCC regulations.

Note: VHF 710CAN operation is the same as VHF 710US. Technical and DSC speciﬁ cations for VHF 710CAN are the same as VHF 710EU

10 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

BAC

GPS/

SC SETU

GPS S

Section 2 - The Radio Menu (MENU)

2-1 Radio Menu Options (Me nu)

The following options are available through MENU (or CALL/MENU):

UDDY LIS

LOCAL/DIS

KLIGH

NTRAS

DATA

ADIO SET

ESE

Maintain your buddy list.

See Section 2-2.

Set backlight level.

See Section 2-4.

MANUAL SETTING

USER MMSID

GROUP SETUP

INDIV REPLY

DSC FUNC

ATIS MMSID

ATIS FUNC

LL REPLY

CH NAME

RING VOLUME

BEEP VOLUME

INT SPEAKER

WATCH MODE

WX ALERT

COM PORT

Set radio sensitivity.

See Section 2-3.

Set contrast level.

See Section 2-4.

Set position & UTC manually.

See Section 2-5.

Set local time and time format.

See Section 2-5.

DSC Setup Menu.

710US and 710EU only.

See Section 4.

Make DSC calls.

710US and 710EU only.

See Section 5.

Radio Setup Menu.

See Section 3.

Turn the GPS Simulator on/oﬀ .

See Section 2.6.

Reset factory settings.

See Section 2.7.

1-3 and 1-4 explain how to navigate around the menu and enter, save and change data.

11Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

2-2 Maintain Your Buddy List ( BUDDY LIST)

VHF 710US and VHF 710EU only.

MENU SELECT

Use the Buddy List to store the names and associated MMSIDs of 20 favourite people.

>BUDDY LIST LOCAL/DIST

The following sections show to use BUDDY LIST to add, edit, and delete entries on

BACKLIGHT

Names are stored in the order of entry, with the most recent entry shown ﬁ rst.

your buddy list.

Section 3 explains how to call a buddy.

2-2-1 Add an En try

BUDDY LIST > MANUAL NEW ALEX TOM

ENTER NAME –––––––––––– ENTER MMSID –––––––––

ENTER NAME BOB ENTER MMSID 123456789

BOB 123456789 > STORE CANCEL

1. Selec t BUDDY LIST. The cursor is at MANUAL NEW. Press ENT.

2. Enter the buddy name, one character at a time (this may be alphanumeric) then press ENT repeatedly until the cursor moves to the MMSID entry line.

4. Enter the MMSID associated with that buddy name (this must be numeric) then press ENT.

5. The new buddy name and MMSID are displayed. Press ENT to store the new entry, which is displayed at the top of your buddy list.

Note that when the BUDDY LIST is full (20 entries), you cann ot make a new entry until you have deleted an existing entry

2-2-2 Edit an E ntry

BUDDY LIST > MANUAL NEW ALEX TOM

ALEX > EDIT DELETE

EDIT NAME ALEX EDIT MMSID 112233445

1. Selec t BUDDY LIST. Press ENT to display the list of entries.

2. Scroll down (if required) to the incorrect entry and press ENT.

3. Select EDIT. The cursor is at the first character of the name.

4. Edit the buddy name or, to edit only the MMSID, press ENT repeatedly until the cursor moves to the MMSID line.

5. When you are finished, press ENT (repeatedly if necessary) to display the next screen.

6. Press ENT to store the changes. The buddy list is displayed again. If more changes are required, repeat Steps 2 thru 6. O therwise, press ESC to exit.

ALEX 111223344 > STORE CANCEL

12 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

2-2-3 De lete an Entry

BUDDY LIST > MANUAL NEW ALEX TOM

BUDDY LIST MANUAL NEW ALEX > TOM

TOM EDIT > DELETE

DELETE BUDDY TOM > YES NO

1. Select BUDDY LIST. Press ENT to display the list of entries.

2. Scroll down (if required) to the entry you want to delete and press ENT.

3. Select DELETE then select YES.

4. The entry is deleted immediately and the buddy list is displayed again.

2-3 Local or Distance Sensi tivity (LOCAL/DIST)

Use LOCAL/DIST to improve the sensitivity of the receiver either locally (LOCAL) or

MENU SELECT BUDDY LIST

LOCAL is not recommended for use in open sea conditions. It is designed for use

> LOCAL/DIST BACKLIGHT

See also SQL (Squelch Control) in Section 1.6.

over distances (DIST).

in areas of high radio noise; for example, close to cities.

2-3-1 Set Di stance Sensitivity

SENSITIVITY > DISTANT LOCAL

1. Select LOCAL/DIST then select DIST.

2. Press ENT to activate the DIST setting. This disables local sensitivity and the menu is displayed again.

2-3-2 Set Lo cal Sensitivity

SENSITIVITY DISTANT > LOCAL

LOCAL is displayed on the LCD as a reminder that local sensitivity is selected.

1. Select LOCAL/DIST then scroll to LOCAL.

2. Press ENT to activate the LOCAL setting. This disables distance sensitivity and the menu is displayed again.

2-4 Backlight ing (BACKLIGHT) and Contrast (CONTRAST)

MENU SELECT LOCAL/DIST > BACKLIGHT CONTRAST

Use BACKLIGHT to set the backlight levels for the LCD and the keypad at a comfortable level.

The microphone keypad backlighting is either ON or OFF.

Use CONTRAST to set the contrast level for the LCD.

13Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

2-4-1 Set the Backlightin g Level

BACKLIGHT LO HI

Note that the DISTRESS key backlighting cannot be switched oﬀ .

1. Select BACKLIGHT.

2. Select a comfortable backlight level using + or - to change the setting.

3. Press ENT to enable the setting and return to the menu.

2.4.2 Set the Contra st Level

CONTRAST LO HI

1. Select CONTRAST.

2. Select a comfortable contrast level using + or - to change the setting.

3. Press ENT to enable the setting and return to the menu.

2-5 GPS Data and Time (GPS/DATA)

MENU SELECT BACKLIGHT CONTRAST > GPS/DATA

This information is important because it will be used if a DSC distress call is transmitted.

You can also enter the course (COG) and speed (SOG) and select GPS Alert and GPS Simulator options.

If the boat has an operational GPS navigation receiver, the VHF radio automatically detects and updates the vessel position and the local time.

However, if the GPS navigation receiver is disconnected or absent, you can specify the vessel position and the local time manually, using the GPS/DATA option.

2-5-1 M anually Enter Positio n and UTC Time (MANUAL)

Note that this function is available only if an operational GPS receiver is not connected.

GPS/DATA > MANUAL SETTING

MANUAL LL ––’ ––’ ––––N ––’ ––’ ––––W MAN ––:––UTC

1. Select GPS/DATA, then MANUAL.

2. Enter the latitude, then the longitude, then the UTC.

3. Press ENT when all the information is correct.

The vessel’s latitude and longitude are shown on the screen, with the UTC time. The preﬁ x MAN indicates

a manual entry. The manual entries are cancelled if a real GPS position is received.

14 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

2-5-2 Local Time (TIME OFFSET)

The local time can be set by entering the time oﬀ set between UTC and local time as follows.

GPS/DATA MANUAL >SETTING

GPS/DATA > TIME OFFSET TIME FORMAT TIME DISPLY

TIME OFFSET >+01:30

02:30PM LOC

1. Select GPS/DATA, then SET TING.

2. Select TIME OFFSET to enter the diﬀ erence between UTC and local time. Half hour increments can be used with a maximum oﬀ set of ±13 hours.

In this example, a diﬀ erence of +1.5 hours has been entered and the local time is displayed with the

suﬃ x LOC.

International Date Line

†

STANDARD TIME ZONES

Daylight Saving Time (Summer Time),

usually one hour in advance of Standard

Compiled by HM Nautical Almanac Office

180°

Corrected to January 2005

Zone boundaries are approximate

Time, is kept in some places

150°W

120°W

90°W

60°W

‡

30°W

+330

+430

0°

C D F

Standard Time = Universal Time + value from table

+530

+630

+930

‡

30°E

+10

+10 30

+11

+11 30

+12

+13

+14

M†

No Standard Time legally adopted

60°E

-1

-2

-3

-330

-4

-5

-6

90°E

M Y

-7

-8

-830

-9

-930

-10

-11

-12

120°E

International Date Line

150°E

‡

180°

WORLD MAP OF TIME ZONES

15Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

2-5-3 Time Format Options (TIME FORMAT)

Time can be shown in 12 or 24 hour format.

GPS/DATA MANUAL > SETTING

SETTING TIME OFFSET > TIME FORMAT TIME DISPLAY

TIME FORMAT > 12 Hr 24 Hr 07:15AM LOC

1. Selec t GPS/DATA, then SE TTING.

2. Select TIME FORMAT.

3. Select 12 Hr or 24 Hr as desired. In this example, 12 hour format has been selected and so the LCD

shows the AM or PM suf fix.

2-5-4 Time Display Op tions (TIME DISPLAY)

If you have entered the time manually as described in the previous sections, the time is always shown on the screen with the preﬁ x M.

However, if the vessel position is being updated through a GPS navigation receiver, you can switch the time display on the screen ON or OFF as follows:

GPS/DATA TIME OFFSET TIME FORMAT > TIME DISPLY

TIME DISPLY ON > OFF

1. Select GPS/DATA, then SET TING.

2. Select TIME DISPLAY.

3. Select ON (on) or OFF (oﬀ ) as desired. In this example, OFF has been selected and so the screen no longer shows the time.

If the time display is set ON, course and speed data are not displayed on the LCD (see section 2-5-6).

2-5-5 Position Display Op tions (LL display)

If you have entered the vessel position manually as described in the previous section, the vessel position is always shown on the screen with the suﬃ x M.

However, if the time is being updated through a GPS navigation receiver, you can switch the vessel position display on the screen on or oﬀ as follows:

GPS/DATA TIME FORMAT TIME DISPLY > LL DISPLAY

LL DISPLAY ON > OFF

1. Select GPS/DATA, then SET TING.

2. Select LL DISPLAY.

3. Select ON (on) or OFF (oﬀ ) as desired. In this example, OFF has been selected and the screen no longer shows the vessel position.

2-5-6 Course & Speed Dis play Options (COG/SOG)

Use this option to display course over ground (COG) and speed over ground (SOG) data on the screen.

GPS/DATA TIME DISPLY LL DISPLY > COG/SOG

COG/SOG > ON OFF

If GOG/SOG is set ON (on), the time is not displayed on the screen (see section 2-5-4).

1. Select GPS/DATA, then SET TING.

2. Select COG/SOG.

3. Select ON (on) or OFF (oﬀ ) as desired. In this example, ON has been selected and so the screen shows the bearing and speed.

16 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

2-5-7 GPS Alert O ptions (ALERT)

The GPS alert is usually set to ON (on) so that if the GPS navigation receiver is disconnected, the alarm sounds.

GPS/DATA LL DISPLY COG/SOG > GPS ALERT

GPS ALERT > ON OFF

1. Select GPS/DATA, then SET TING.

2. Select GPS ALERT.

3. Select ON (on) or OFF (oﬀ ) as desired.

2-6 GPS Simulator (SIMUL ATOR )

The GPS Simulator is set to OFF whenever the radio is turned ON or whenever real GPS data is available through the COM port. However, if you want to test it, turn it on.

MENU SELECT DSC SETUP RADIO SETUP > GPS SIM

1. Select GPS SIM, then select ON (on) or OFF (oﬀ ) as desired.

Whenever the GPS Simulator is turned ON (on), simulated Speed Over Ground

(SOG), Course Over Ground (COG), and LL position appear on the screen. This data is updated automatically during the simulation.

It is not possible to send a DSC transmission when in Simulator mode.

2-7 Reset to Factory Defau lts (RESET)

Use this to return every setting to the factory defaults except all MMSID settings and the entries in your buddy list.

MENU SELECT RADIO SETUP GPS SIM > RESET

RESET RADIO ARE YOU SURE > YES NO

1. Selec t RESET. The radio asks for confirmation.

2. Select YES to reset the radio and return to the menu.

The Call Logs will be cleared but the BUDDY LIST will be saved. The receiver and transmitter factory

settings are restored to default conditions.

17Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

Section 3 - Radio Setup Menu (RADIO SETUP)

3-1 Radio Setup Menu (RADIO SETUP)

CH NAME

RING VOLUME

BEEP VOLUME

INT SPEAKER

WATCH MODE

WX ALERT

COM PORT

Sections 1-3 and 1-4 explain how to navigate around the menu and enter, save and change data.

3-2 Channel Names (CH NAME)

The channel charts are listed in Appendix C with their default name tags. CH NAME gives you the option to edit or delete the channel name tags displayed on the screen.

RADIO SETUP > CH NAME RING VOLUME BEEP VOLUME

Edit or delete channel names.

See Section 3-2.

Set the volume level of the incoming call notiﬁ cation beeps.

See section 3-3.

Set the volume level of the beeps.

See section 3-3.

Switch ON/OFF (on/oﬀ ) the radio’s internal speakers.

See section 3-4.

Selects the operation of Dual or Tri watch scanning.

See section 3-5.

(Selects if the WX Alert scanning mode is ON (on) or OFF (oﬀ ). ( VHF 710US only.)

See section 3-6.

Select NMEA protocol for communications between the VHF radio and any other instruments.

See section 3-7.

CH NAME 01

TELEPHONE

TELEPHONE > EDIT DELETE

EDIT CH NAME TELEPHONE

SAVE CH NAME PHONE1 > YES NO

1. Select RADIO SETUP, then CH NAME.

2. Use + or - to step through the channels with their name tags until you see the channel name tag you want to change, then press ENT. In this example, the channel name TELEPHONE associated with channel 01 is being changed to PHONE1.

3. Select EDIT and press ENT to edit the existing name tag. Input the new name

over the existing name.

It can be a maximum of 12 characters.

To delete the channel name, select DELETE and press ENT.

4. Press ENT (repeatedly if necessary) to display the YES/NO conﬁ rmation.

5. Press ENT to conﬁ rm the new channel name tag or the deletion, then press ESC to return to the menu.

18 Northtstar Explorer VHF Series: 710US, 710EU Operation and Installation Manual

+ 39 hidden pages

NorthStar Navigation Explorer 710 VHF User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual