NordicTrack 831283190 Owner’s Manual
oteot en°,no SL 720
Model No. NTC69020
Serial No.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
satisfaction through direct assis-
tance from our factory.
USER'S MANUAL
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.-Fri., 6 a.m.-6 p.m. MST
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
_sit our website at
.... I
www.nordictrack.com I
new products, prizes,
fitness tips, and much morel
SL 720
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ............................................................. 3
BEFORE YOU BEGIN ................................................................... 4
ASSEMBLY ........................................................................... 5
HOW TO OPERATE THE EXERCISE CYCLE ................................................ 10
MAINTENANCE AND TROUBLESHOOTING ................................................. 22
EXERCISE GUIDELINES ................................................................ 23
PART LIST ........................................................................... 25
EXPLODED DRAWING ................................................................. 26
HOW TO ORDER REPLACEMENT PARTS ........................................... Back Cover
LIMITED WARRANTY ........................................................... Back Cover
NordicTrack isa registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
_ WARNING: To red.c, the risk of serious injury, read the following important precau-
tions before using the exercise cycle.
1. Read all instructions in this manual before
using the exercise cycle. Use the exercise
cycle only as described.
2. It is the responsibility of the owner to
ensure that all users of the exercise cycle 8.
are adequately informed of all precautions.
3.
Use the exercise cycle Indoors on a level
surface. Keep the exercise cycle away from
moisture and dust. Place a met under the
exercise cycle to protect the floor or carpel
4. Inspect and properly tighten all parts regu-
larly. Replace any wom parts immediately.
5. Keep children under the age of 12 and pets
away from the exercise cycle at all times.
6. The exercise cycle should not be used by
persons weighing more than 250 pounds.
7.
Wear suitable clothing when using the
exercise cycle; do not wear loose clothing
that could become caught on the exercise
cycle. Always wear athletic shoes.
Always keep your back straight when using
the exercise cycle. Do not arch your back.
9. If you feel pain or dizziness while exercis-
ing, stop immediately and cool down.
10. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. The exorcise cycle is Intended for in-home
use only. Do not use the exercise cycle in a
commercial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this producL
3
BEFORE YOU BEGIN
Congratulations for selectingthe new NordicTrack_
SL 720 exercise cycle. Cycling is one ofthe most
effectiveexercisesfor increasingcardiovascularfit-
ness, buildingendurance, and toningthe entire body.
The NordicTrack®SL 720 offersan impressivearray
of features designedto let you enjoythis healthful
exercise inthe comfortand privacyof your home,
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
afterreading this manual, call our Customer Service
Bookrack
Seat
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, mention
the product model number and serial number when
calling. The model number is NTC69020. The serial
number can be found on a decal attached to the exer-
cise cycle (see the front cover of this manual for the
location of the decal).
Before readingfurther,please familiarize yourself with
the parts that are labeled inthe drawingbelow.
Fan
Console
FRONT
Backrest
Handlebar
REAR
Leveling Foot
Seat Knob
Wheel
Pulse Sensor
RIGHT SIDE
*No water bottle isincluded
4
ASSEMBLY
Assembly requires two persons. Place all partsofthe exercise cycle ina cleared area and remove the packing
materials, Do not dispose of the packingmaterialsuntil assembly iscompleted.
Assembly requires the included tools and your own adjustable wrench _.
Use the drawings below to identifythe small parts used in assembly.The number in parenthesis below each
drawingrefers to the key number of the part, from the PART LIST on page 25, The secondnumber refersto the
quantityneededfor assembly.Note: Some small parts may have been pre-assembled for shipping. If a part
is not in the parts bag, check to see if it has been pre-assembled.
M8 Split M8 Washer
Washer (55)-12 (60)-4
M4 x 16mm 1/4" x 16mmButton
Screw (57)-4 Screw (80)-4
M1Ox 52mm ButtonBolt (82)-2
1. Identify the Front Stabilizer (15). While another person
liftsthe frontof the Frame (1), attachthe Front
Stabilizerto the Frame withfour M8 x 40mm Button
Screws(54) and four M8 SplitWashers (55).
M8 x 25mm Button
Screw (79)-4
M10 x 110mm ButtonScrew (78)-2
M1g Split
Washer (88)-2
M10 Nylon
Locknut(63)-2
M8 x 4gram Button
Screw (54)-8
54
5
2. While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (16) to the Frame with four
M8 x 40mm Button Screws (54) and four M8 Split
Washers (55).
2
3. Have another person hold the Upright (2) in the posi-
tion shown. Refer to the inset drawing. Locate the wire
extending from the bottom of the Updght. Tie the wire
around the ends of the Wire Harness (43) and the
Pulse Wire (3) as shown. Carefully pull the wire up
through the Upright until the Wire Hamess and the
Pulse Wire are extending from the top of the Upright.
Untie the wire and discard it. Carefully pull the ends
of the Wire Harness and the Pulse Wire to remove
any slack.
Insert the Upright(2) into the Frame (1). Be careful to
avoid pinching the Wire Harness (43) or the Pulse
Wire (3), Attach the Uprightwithtwo M10 x 110mm
ButtonScrews (76) and two M10 SplitWashers (88),
4. Have another person hold the Console (4) near the
Upright (2).
3
78
4
88
2
\
Do not pinch the
Wire Harness
(43) or the Pulse
Wire (3) during
this step,
Connect the Wire Harness (43) to the wire harness on
the Console (4). Connect the Pulse Wire (3) to the
pulse wire on the Console. Next, locate the two ground
wires that are connected with a screw to the Upright
(2). Connect the ground wires to the two smallest wires
on the Console.
Carefully insert all excess wiring down into the Upright
(2). Attach the Console (4) to the Upright with four M4
x 16mm Screws (57). Be careful to avoid pinching
the wires.
57
Ground Wires
Do not pinch
the wires
during this step.
6
5. Attach the Seat (9) to the Seat Frame (7) with four 1/4" 5
x 16mm Button Screws (80) and four M8 Washers (60).
6. Make sure that the Seat Carriage (1t) is in the posi-
tion shown. If necessary, pull the Seat Knob (10)
and slide the Seat Carriage forward.
Have another person hold the Seat Frame (7) near the
Seat Carriage (11). Locate the two pulsewires extend-
ingfrom the Seat Frame. Connect each pulsewire to
the pulse wire of the same color inthe Seat Carriage.
Insertthe excess wiring up intothe Seat Frame, and
set the Seat Frame onthe Seat Carriage.Attach the
Seat Frame with two M10 x 52mm Button Bolts(82)
and two M10 Nylon Locknuts(63). Be careful to
avoid damaging the pulse wires with the Bolts.
7. Attach the Backrest (62) to the Backrest Frame (42)
with four 1/4"x 16mm ButtonScrews (80).
Slide the BackrestFrame (42) onto the Seat Frame
(7). Attach the Backrest Frame with four M8 x25mm
ButtonScrews (79) and four M8 SplitWashers (55).
6
83
>Pulse Wires
7
62
42
55
79
8O
7
8. Identify the Left Pedal (22), which is marked with an
"L." Using an adjustable wrench, firmly tighten the
Left Pedal counterclockwise into the Left Crank Arm
(24). Tighten the Right Pedal (not shown) clockwise
into the Right Crank Arm. Important: Tighten both
Pedals as firmly as possible. After using the
exercise cycle for one week, retighten the
Pedals. For best performance, the Pedals must
be kept tightened.
Identify the Left Pedal Strap (25), which is marked
with an "L." Attach the Left Pedal Strap to the Left
Pedal (22), and adjust it to the desired position.
Attach and adjust the Right Pedal Strap (not shown)
in the same way.
9. Make sure that all parts are properly tightened before you usa the exercise cycle. Note: After assemblyis
completed, some extraparts may be left over. Place a mat beneath the exercisecycle to protect the floor.
25
8
INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
If you purchase the optional chest pulse sensor (see page 21), follow the steps below to install the receiver
included with the chest pulse sensor.
Remove the access door from the underside ofthe
Console (4). You may need to use a small standard
screwdriver to remove the access door.
Access
Door
Slide the receiver ontothe indicatedplastic pin on the
Console (4); make sure that the receiver is oriented
exactly as shown. Locate the two small screws included
with the chest pulse sensor.Attach the receiverto the
Consolewith the two screws as shown.
Pin
Connect the wire on the receiver to the indicatedwire on
the Console (4).
Reattach the access door. Make sure that no wires are
pinched. Note: The other wires includedwiththe chest
pulsesensormay be discarded.
/
crews
Wire
Receiver
Loading...