NOKIA 3250 service manual-1,2 v3

Page 1
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support
Page (32)
CONFIDENTIAL
1
SERVICE MANUAL
Level 1&2
RM-38
Transceiver characteristics:
Approved 3.0
05.July.2007
Band: Tri-band phone for GSM/EDGE 900/1800/1900MHz
Camera: Integrated camera 2 Megapixel
Display: TFT Active matrix color display with 262.144 colors,
high resolution 176 x 208 pixel
Bluetooth
FM radio, MP3/eAAC+
Vibra Alert
Connector: Pop Port™ connector
Memory expandable up to 1GB (Micro SD card)
Twist- On design
USB 2.0
Transceiver with BP-6M 1100mAh Li-Ion battery pack
Talk time Standby Note
up to 3 h up to 10 days
Environmental characteristics:
Depends on network
parameters
Lead-free soldered
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 2
Page (32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
2
Approved 3.0
05.July.2007
TABLE OF CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
INTRODUCTION 3
EXPLODED VIEW AND COMPONENT DISPOSAL 4
SPARE PARTS OVERVIEW 5
SERVICE DEVICES 6
SW-UPDATE 8
DISASSEMBLY INSTRUCTION UPPER BLOCK 9
ASSEMBLY INSTRUCTION UPPER BLOCK 14
DISASSEMBLY INSTRUCTION LOWER BLOCK 20
ASSEMBLY INSTRUCTIONS LOWER BLOCK 23
LEGEND OF QUICK TROUBLE SHOOTER 28
QUICK TROUBLE SHOOTER PART 1 29
QUICK TROUBLE SHOOTER PART 2 30
QUICK TROUBLE SHOOTER PART 3 31
Page
14.
QUICK TROUBLE SHOOTER PART 4 32
CHANGE HISTORY
Status Version No. Date Comments
Draft 0.1 16.1.2006 Initial draft
Approved 1.0 13.3.2006
Approved 2.0 16.3.2006 Service Tools modified
Approved 3.0 05.July.2007 Exploded view & Spare Parts overview updated (I216 added)
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 3
Page (32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
3
Approved 3.0
05.July.2007

INTRODUCTION1.

The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to service NOKIA products. This Service Manual must be used only by authorized NOKIA service suppliers. The content of it is confidential. Please note that NOKIA also provides other guidance documents (e.g. Service Bulletins) for service suppliers. Follow these regularly and comply with the given instructions.
While every effort has been made to ensure the accuracy of this document, some errors may exist. If you find any errors or if you have further suggestions, please notify NOKIA using the address below: mailto:cc-ts-rc.documentation@nokia.com
Please keep in mind also that this documentation is continuously being updated and modified, so always watch out for the newest version.
Warnings and Cautions
Please refer to the phone’s user’s guide for instructions relating to operation, care, and maintenance, which include impor­tant safety information. Note also the following:
Warnings:
CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS AND
1. ANTI–SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY. THE CELLULAR TELEPHONE MUST NOT BE OPERATED IN
2. AREAS LIKELY TO CONTAIN POTENTIALLY EXPLOSIVE ATMOSPHERES, EG PETROL STATIONS (SERVICE STATIONS), BLASTING AREAS ETC. OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY INTERFERE WITH THE
3. FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT A PHYSICIAN OR THE MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS. OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO INTERFERENCE.
Cautions:
1. Servicing and alignment must be undertaken by qualified personnel only.
2. Ensure all work is carried out at an anti–static workstation and that an anti–static wrist strap is worn.
3. Use only approved components as specified in the parts list.
4. Ensure all components, modules, screws, and insulators are correctly re–fitted after servicing and alignment.
5. Ensure all cables and wires are repositioned correctly.
Electrostatic discharge can easily damage the sensitive components of electronic products. Therefore, every Service Supplier must observe the precautions, mentioned in the appropriate “Service Partner Requirements”, available on NOKIA Online. Also see ESD Protection Require­ments in this Service Manual.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 4
(32)
Page
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
4
Approved 3.0
05.July.2007

EXPLODED VIEW AND COMPONENT DISPOSAL2.

Recommendation for the ecologically friendly disposal of components. Colorized components show the various categories. See the corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 5
Page (32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
5

SPARE PARTS OVERVIEW3.

Approved 3.0
05.July.2007
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 6
Page (32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
6

SERVICE DEVICES4.

Approved 3.0
05.July.2007
FLS-4S incl. ACF-8, Driver and User Guide Dongle and flash device combined, developed specifically for POS use.
ACF-8 Universal Power Supply for FLS-4S.
Travel Charger AC-4 Small and lightweight charger for fast charging of your phone battery.
Internal Battery BP-6M Inserted under the back cover, this Li-Ion 1100 mAh battery provides power in a lightweight package.
Headset HS-3 Provides convenient handsfree use and the pleasure of listening to music in stereo from your compatible Nokia phone. Available in black and white.
SS-45 Camera Removal Tool.
CA-53
Service Cable to connect the PC with the Pop-Port™ connector.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 7
Page (32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
SS-93
Opening Tool
RJ-113
Soldering Jig
Lead-free Soldering Wire
Mandatory for lead-free products (Level 2 only).
7
Approved 3.0
05.July.2007
0772040 NMP Standard Toolkit
NOKIA opening tool SRT-6 NOKIA No. 0770431
• Tonichi torque driver NOKIA No. 6901525
Hoya micro ber cloth MX304
• Dastex gloves S, M, XL
• Artilux goggles AH166
• Wera bit T5 867/4TX 5x50
Wera 867/4 6IP; 50mm (Torx 6 PLUS®)
• Wera bit T6 867/4TX 6x50
• Wera 867/1 5IP; 25mm (Torx 5 PLUS®)
• Wera bit T6 PLUS® 867/4TX 6IP
Facom side cutter 416E
Facom T5 driver SP.14032
• Facom T6 driver SP.14033
• Facom slot screwdriver AEF. 2x35.E
Wetec tweezers 7abb SA-ESD
Wetec tweezers 22 SA-ESD
• Wetec tweezers 13 SA-SMD ESD
• Wetec tweezers PSF SA-ESD
• Wetec ESD brush E1211
Kaiser Fototechnik airbrush 6315
Wetec dental tool DEM83266/0
RS Components scissors 323-5732
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 8
Page (32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
8
Approved 3.0
05.July.2007

SW-UPDATE5.

Flash Concept – (Point of Sales)
To use the FLS-4S Flash Dongle you should follow the user’s guide inside the sales package. Always check for the latest ver­sion of flash software, which is available on NOKIA Online.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 9
(32)
Page
9
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL

DISASSEMBLY INSTRUCTION UPPER BLOCK6.

Approved 3.0
05.July.2007
1. You will need the following tools: The SRT-6, metal tweezers, a Torx plus size 6 driver, the SIM Tool, a torque driver with a torx plus size 6 bit, and a DC Plug.
3. Gently pry open the A-COVER ASSEMBLY with the SRT-6 and discard it. Do not use it again.
2. Unlock and remove the BATTERY COVER.
4. Push down both metal latches to unlock the snaps of the CAP­COVER.
5. Release both screws in the order shown.
6. Do not mismatch these screws with the other ones.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 10
10
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
7. Remove the KEYMAT ASSEMBLY SYMBIAN.
9. Gently open the ex connector with the SRT-6.
8. Carefully bend open the 2 metal snaps of the DISPLAY SHIELD ASSEMBLY on the left side.
10. When the clips are released properly, the shield can be lifted up easily.
11. Separate the LCD MODULE by releasing the 4 snaps with the SRT-6.
12. Carefully slot through the ex connector. Always use a new
DISPLAY SHIELD ASSEMBLY when reassembling.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 11
(32)
Page
11
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
13. Cover the display with a protective lm.
15. Remove the screws. Do not mismatch these screws with the other ones.
14. Release the next both screws in the order shown.
16. Carefully open the UPPER BLOCK CONNECTOR.
17. Also open the BOARD TO BOARD CONNECTOR with the SRT-6
18. Lift up both connectors and shift out the ENGINE MODULE ASSEMBLY.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 12
12
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
19. Carefully release the clips of the ANTENNA FRAME ASSEMBLY. These clips are very delicate and can easily be damaged.
21. Peel up the CABLE SUPPORT TAPE.
20. Prevent scratching the PWB surface while unlocking the clips of the EARPIECE ASSEMBLY.
22. Unscrew the 4 screws in the order shown.
23. These 4 screws are different . Do not mismatch these screws with the other ones.
24. Carefully separate the lower block, but remember the UPPER BLOCK CONNECTOR.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 13
13
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
25. Release the adhered DOMESHEET with the SRT-6.
27. Shift out the MAIN FLEX ASSEMBLY and discard it. Do not use it again when assemble.
26. Push down the MAIN FLEX ASSEMBLY with your thumb to release the adhesive tape from the UPPER FRAME ALUMINIUM.
28. The POP PORT DOOR can be pulled out easily. Always use a new MAIN FLEX ASSEMBLY when reassembling.
29. The disassembling procedure is now complete.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 14
Page (32)
14
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL

ASSEMBLY INSTRUCTION UPPER BLOCK7.

Approved 3.0
05.July.2007
1. Remove the cover tape from the MAIN FLEX ASSEMBLY…
3. Peel up the cover tape from the DOMESHEET.
2. Shift the MAIN FLEX ASSEMBLY into the UPPER FRAME ALUMINIUM.
4. Align the DOMESHEET with the SIM Tool, mind the surrounding components.
5. Now x the MAIN FLEX ASSEMBLY to the UPPER FRAME ALUMINIUM using nder pressure.
6. Carefully bend down both SWIVEL SENSOR ex foils.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 15
Page (32)
15
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
7. Bring the Lower Block into position above the UPPER FRAME ALUMINIUM and align the 2 SWIVEL SENSORS into their guides.
9. Tighten the 4 screws slightly.
8. Insert the screws with tweezers, note the different screw types.
10. Check the correct positioning of the SWIVEL SENSORS.
11. Now, tighten the screws with the correct torque in the order shown, using a torque of 18 Ncm .
12. Fix the cables with a new Cable Support Tape.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 16
Page (32)
16
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
13. Align the EARPIECE ASSEMBLY and click it into its place.
15. Push down the Cables while shifting the assembly into the UPPER FRAME ALUMINIUM.
14. Mind the guiding pins while xing the ENGINE MODULE to the
ANTENNA FRAME ASSEMBLY. Ensure that all snaps are engaged.
16. Close the BOARD TO BOARD CONNECTOR.
17. Close the UPPER BLOCK CONNECTOR by using nger pressure.
18. Place the screws, note the different used screw types.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 17
17
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
19. Tighten the screws in the order shown, using a torque of 18Ncm.
21. Fix all metal latches of the DISPLAY SHIELD ASSY.
20. Slot through the ex foil of the LCD MODULE.
22. Close the ex connector.
23. Flip over the DISPLAY SHIELD ASSEMBLY and push it into its place.
24. Fix it using nger pressure.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 18
18
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
25. Ensure that all snaps on both sides are well locked. The left side is shown here.
27. Tighten the screws in the order shown, using a torque of 18 Ncm.
26. Insert the screws with tweezers, note the different screw types.
28. Place the CAP COVER and x both latches.
29. Insert the KEYMAT ASSEMBLY SYMBIAN.
30. Remove the cover tape and place the new A-COVER ASSEMBLY, beginning from the top.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 19
19
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
31. Fix all the plastic clips.
32. Complete the assembly by placing the BATTERY COVER.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 20
(32)
Page
20
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL

DISASSEMBLY INSTRUCTION LOWER BLOCK8.

Approved 3.0
05.July.2007
1. You will need the following tools: The SRT-6, metal tweezers, the SS-45 Camera removal tool, a dental tool, a torque driver with a Torx Plus ® size 6 bit, and a Torx Plus ® driver size 6.
3. Carefully pry open the CAMERA LENS ASSEMBLY and remove it.
2. Always cover the windows with protective lm. Remove the
battery if still inserted.
4. Unlock and remove the SMIA 2MPIX CAMERA with the SS-45.
5. Unlock the LOWER CAP COVER with the SRT-6.
6. Remove the LOWER FRONT COVER and the KEYMAT ASSY NUMERIC.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 21
21
Page
(32)
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
7. Turn the assembly and remove the LOWER BACK COVER.
9. Peel up the COAX CABLE SUPPORT TAPE
8. Lift up the KEYMAT ASSY MUSIC.
10. Carefully open the LOWER BLOCK CONNECTOR with the dental tool. Do this evenly on both sides of the connector.
11. Turn the upper block in order to prevent mechanical stress to the joystick while unscrewing the screws.
12. Release the screws in the order shown.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 22
(32)
Page
22
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
13. Now turn around the upper block.
15. Carefully separate the parts.
14. Continue with the next screws in the order shown.
16. Pass out the LOWER SIDE RAIL RIGHT.
17. Remove the LOWER SIDE RAIL LEFT, too.
18. The disassembly procedure of the upper block is now completed.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 23
(32)
Page
23
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL

ASSEMBLY INSTRUCTIONS LOWER BLOCK9.

Approved 3.0
05.July.2007
1. Start with the LOWER AUDIOBOX ASSEMBLY.
3. Place the LOWER SIDE RAIL LEFT, too.
2. Place the LOWER SIDE RAIL RIGHT.
4. Bring the parts together, positioning as shown. Mind the correct positioning of the LOWER BLOCK CONNECTOR.
5. Insert the screws.
6. Turn the unit to prevent mechanical stress to the joystick.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 24
(32)
Page
24
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
7. To prevent damaging the plastic threads, turn the screws left
rst, then thighten them slightly.
9. Turn over the lower block.
8. Apply the torqure of 18Ncm to the screws in the order shown.
10. Continue tightening the next screws with the torque of 18 Ncm in the order shown.
11. Turn back the lower block.
12. Carefully close the connector. Do this evenly side by side.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 25
(32)
Page
25
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
13. Protect the connector with a new COAX CABLE SUPPORT TAPE.
15. Mind the guiding pins.
14. Position the KEYMAT ASSY MUSIC.
16. Insert the LOWER BACK COVER and x the snaps.
17. Turn the lower block.
18. Insert the KEMAT ASSY NUMERIC and x the snaps.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 26
(32)
Page
26
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
19. Place the LOWER FRONT COVER.
21. Mind the guide pin before positioning of the SMIA 2 MPIX CAMERA.
20. Fix all the parts while placing the LOWER CAP COVER.
22. Grip the camera with the SS-45.
23. Place the camera into its housing.
24. Push down the Camera evenly.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 27
(32)
Page
27
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
Approved 3.0
05.July.2007
25. Place the CAMERA LENS ASSEMBLY and x it.
26. Check the window for correct positioning and cleanness.
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 28
(32)
Page
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
28

LEGEND OF QUICK TROUBLE SHOOTER10.

Approved 3.0
05.July.2007
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 29
(32)
Page
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
29

QUICK TROUBLE SHOOTER PART 111.

Approved 3.0
05.July.2007
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 30
(32)
Page
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
30

QUICK TROUBLE SHOOTER PART 212.

Approved 3.0
05.July.2007
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 31
31
Page
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
(32)

QUICK TROUBLE SHOOTER PART 313.

Approved 3.0
05.July.2007
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 32
(32)
Page
CMO Operations & Logistics Training & Vendor Development Multimedia Creation & Support CONFIDENTIAL
32

QUICK TROUBLE SHOOTER PART 414.

Approved 3.0
05.July.2007
Service Manual 3250 RM-38 Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Loading...