Important: For important information on the safe use of your device and battery,
read “For your safety” and “Product Safety” info in the printed user guide, or at
www.nokia.com/support before you take the device into use. To find out how to get started
with your new device, read the printed user guide.
Avoid touching the antenna area while the antenna is in use. Contact with antennas affects the
communication quality and may reduce battery life due to higher power level during operation.
Do not connect to products that create an output signal, as this may damage the device. Do
not connect any voltage source to the audio connector. If you connect an external device
or headset, other than those approved for use with this device, to the audio connector, pay
special attention to volume levels. Parts of the device are magnetic. Metallic materials may be
attracted to the device. Do not place credit cards or other magnetic storage media near the
device, because info stored on them may be erased.
Some of the accessories mentioned in this user guide, such as charger, headset, or data cable,
may be sold separately.
Note: The pre-set security code is 12345. To switch on the security code, select Menu >
Settings > Security settings > Phone security , enter the code 12345 and select OK , and
then select On . To change the security code, select Menu > Settings > Security settings
> Change codes > Change security code , enter the current security code and select OK .
Enter your new code and select OK , then enter the new code again and select OK . When you
change the code, you need to remember the new code, as HMD Global is not able to open or
bypass it.
SET UP AND SWITCH ON YOUR PHONE
Mini SIM
Important: This device is designed to be used with a mini SIM card (see figure) only. Use of
incompatible SIM cards may damage the card or the device, and may corrupt data stored on
the card.
Note: Switch the device off and disconnect the charger and any other device before removing
any covers. Avoid touching electronic components while changing any covers. Always store
and use the device with any covers attached.
If you have a dual-SIM phone, slide the second SIM in the SIM2 slot. Both SIM cards are
available at the same time when the device is not being used, but while one SIM card is active,
for example, making a call, the other may be unavailable.
Tip: To find out if your phone can use 2 SIM cards, see the label on the sales box. If there are
2 IMEI codes on the label, you have a dual-SIM phone.
Insert the memory card
1. If you have a memory card, slide it in the memory card slot.
2. Put back the battery.
3. Put back the cover.
Switch on your phone
Press and hold .
CHARGE YOUR PHONE
Your battery has been partially charged at the factory, but you may need to recharge it before
you can use your phone.
2. Connect the charger to the phone. When done, unplug the charger from the phone, then
from the wall outlet.
If the battery is completely discharged, it may take several minutes before the charging
indicator is displayed.
Tip: You can use USB charging when a wall outlet is not available. Data can be transferred
while charging the device. The efficiency of USB charging power varies significantly, and it
may take a long time for charging to start and the device to start functioning. Make sure your
computer is switched on.
KEYPAD
Use the phone keys
• To see the apps and features of your
phone, on the home screen, select Menu .
• To go to an app or feature, press the scroll
key up, down, left, or right. To open the
app or feature, press the scroll key.
• To go back to the home screen, press the
end key .
Lock the keypad
To avoid accidentally pressing the keys, lock the keypad: select Go to > Lock keypad . To
unlock the keypad, press , and select Unlock .
• To change the volume of your phone,
press the volume up or volume down key.
• To switch on the flashlight, on the home
screen, press the scroll key up twice. To
switch it off, scroll up once. Do not shine
the light in anyone’s eyes.
WRITE TEXT
Write using the keypad
Press a key repeatedly until the letter is shown.
To type in a space press the 0 key.
To type in a special character or punctuation mark, press the asterisk key, or if you are using
predictive text, press and hold the asterisk key.
To switch between character cases, press the # key repeatedly.