NEC E540I User Manual

Emergency Services and Safety
Precautions

Emergency Services

To make an emergency call in any country

☛ Press 1 1 2

Ask the operator for the service which you require: Police, Ambulance, Fire Brigade,
Coastguard or Mountain Rescue Services. Give your position and, if possible, remain
stationary to maintain phone contact.
The 112 emergency number service is available on every digital network service. The
number 999 is an alternative emergency number for the UK only, and can only be used
with a valid SIM card.

2 Due to the nature of the cellular system, the success of emergency calls

cannot be guaranteed.

General Care

A cellphone contains delicate electronic circuitry, magnets, and battery systems. You
should treat it with care and give particular attention to the following points.

• Do not allow the phone or its accessories to come into contact with liquid or moisture

at any time.

• Do not place anything in the folded phone.

• Do not expose your phone to extreme high or low temperatures.

• Do not expose your phone to naked flame, cigars or cigarettes.

• Do not paint your phone.

• Do not drop or subject your phone to rough treatment.

• Do not place the phone alongside computer disks, credit cards, travel cards and other

magnetic media. The information contained on disks or cards may be affected by the
phone.

• Do not leave the phone or the battery in places where the temperature could exceed

60°C; e.g. on a car dashboard or on a window sill, behind glass in direct sunlight, etc.

• Do not remove the phone’s battery while the phone is switched on.

• Take care not to allow metal objects, such as coins or key rings, to contact or short-

circuit the battery terminals.

• Do not dispose of battery packs in a fire. Your phone's Li-ion batteries may be safely

• The earpiece may become warm during normal use and the unit itself may become

warm during charging.

• Use a damp or anti-static cloth to clean the phone. Do NOT use a dry cloth or

electrostatically charged cloth. Do not use chemical or abrasive cleaners as these
could damage the case.

• Remember to recycle: the cardboard packaging supplied with this phone is ideal for

recycling.

• Do not leave the battery pack empty or disconnected for a long time, otherwise some

data may be initialized.

• Your phone contains metal which may cause you an itch, a rash or eczema depending

on your constitution or physical condition.

• Take care not to put your phone in the back pocket of your trousers or skirt and then

sit on it. Also, do not put your phone at the bottom of bag where it may subject to
excessive weight or pressure.
Doing so may damage the LCD and camera lens and cause them malfunction.

• Take care not to hold the Light too close to your or other people’s eyes when the Light

is lit.

• Do not aim or direct the InfraRed (IR) data port towards your or other people’s eyes

when using the IR data exchange.

• The foam covers the earpiece of the headset. Do not put any other part of the headset

in your ears.

Aircraft Safety

• Switch off your phone and remove its battery when inside or near aircraft. The use of

cellphones in aircraft is illegal. It may be dangerous to the operation of the aircraft and
it may disrupt the cellular network. Failure to observe this instruction may lead to
suspension or denial of cellphone service to the offender, or legal action, or both.

• Do not use your phone on the ground without the permission of the ground crew.

Hospital Safety

• Switch off your phone in areas where the use of cellphones is prohibited. Follow the

instructions given by the respective medical facility regarding the use of cellphones on
their premises.

General Safety

• Observe ‘Turn off 2-way radio’ signs, such as those near stores of fuel, chemicals or

explosives.

• Do not allow children to play with the phone, charger or batteries.

Road Safety

• You MUST exercise proper control of your vehicle at all times. Give full attention to

driving.

• Observe all the recommendations contained in your local traffic safety documentation.

• Pull off the road and park before making or answering a call if driving conditions so

require.

• You MUST NOT stop on the hard shoulder of a motorway to answer or make a call,

except in an emergency.

• Switch off your phone at a refuelling point, such as a petrol station, even if you are not

refuelling your own car.

• Do not store or carry flammable or explosive materials in the same compartment where

a radio transmitter, such as a cellphone, is placed.

• Electronic vehicle systems, such as anti-lock brakes, speed control and fuel injection

systems are not normally affected by radio transmissions. The manufacturer of such
equipment can advise if it is adequately shielded from radio transmissions. If you
suspect vehicle problems caused by radio transmissions, consult your dealer and do
not switch on your phone until it has been checked by qualified approved installers.

Vehicles Equipped with an Air Bag

An air bag inflates with great force. Do not place objects, including either installed or
portable wireless equipment, in the area over the air bag or in the air bag deployment
area. If in-vehicle wireless equipment is improperly installed and the air bag inflates,
serious injury could result.

Third Party Equipment

The use of third party equipment, cables or accessories, not made or authorized by NEC,
may invalidate the warranty of your cellphone and also adversely affect the phone’s
operation. For example use only the NEC mains cable supplied with the AC charger.

Service

The cellphone, batteries and charger contain no user-serviceable parts. We recommend
that your NEC cellphone is serviced or repaired by an NEC authorized service centre.
Please contact your Service Provider or NEC for advice.

Non-Ionizing Radiations

The radio equipment shall be connected to the antenna via a non-radiating cable (e.g. coax).
The antenna shall be mounted in a position such that no part of the human body will
normally rest close to any part of the antenna unless there is an intervening metallic

Radio Frequency Energy

Your phone is a low-power radio transmitter and receiver. When it is turned on, it
intermittently receives and transmits radio frequency (RF) energy (radio waves). The
system that handles the call controls the power level at which the phone transmits.

Exposure to Radio Frequency Energy

Your phone is designed not to exceed the limits for exposure to RF energy set by
national authorities and international health agencies. * These limits are part of
comprehensive guidelines and establish permitted levels of radio wave exposure for the
general population. The guidelines were developed by independent scientific
organizations such as ICNIRP (International Commission on Non-Ionizing Radiation
Protection) through periodic and thorough evaluation of scientific studies. The limits
include a substantial safety margin designed to assure the safety of all persons,
regardless of age and health, and to account for any variations in measurements.
*Examples of radio frequency exposure guidelines and standards that your phone is

designed to conform to:

• ICNIRP, “Guidelines for limiting exposure to time-varying electric, magnetic, and

electromagnetic fields (up to 300 G Hz)-International Commission on Non-Ionizing
Radiation Protection (ICNIRP)”.
Health Physics, vol. 74. pp, 494-522, April 1998.

• 99/519/EC Council Recommendation on the limitation of exposure to the general

public to electromagnetic fields 0 Hz-300 GHz, Official Journal of the European
Communities, July 12,1999.

• ANSI/IEEE C95.1-1992. “Safety levels with respect to human exposure to radio

frequency electromagnetic fields, 3kHz to 300 GHz”. The Institute of Electrical and
Electronics Engineers Inc., New York, 1991.

• FCC Report and Order, ET Docket 93-62, FCC 96-326, Federal Communications

Commission (FCC), August 1996.

• Radio communications (Electromagnetic Radiation Human Exposure) Standard 2003,

Australian Communications Media Authority.

Declaration of Conformity

• This product complies with the requirements of the R&TTE Directive 1999/5/EC. The

‘Declaration of Conformity’ leaflet can be found within this box.

Disposing of your used NEC product

•In the European Union

EU-wide legislation as implemented in each Member State requires

Licenses

• T9

®

Text Input and the T9 logo are registered trademarks of Tegic Communication.

“T9 Text Input is licensed under one or more of the following:
U.S. Pat. Nos. 5,187,480, 5,818,437, 5,945,928, 5,953,541, 6,011,554, 6,286,064,

6,307,548, 6,307,549, and 6,636,162, 6,646,573; Australian Pat. Nos. 727539,
746674, and 747901; Canadian Pat. Nos. 1,331,057, 2,302,595, and 2,227,904; Japan
Pat. No. 3532780, 3492981; United Kingdom Pat. No. 2238414B; Hong Kong
Standard Pat. No. HK1010924; Republic of Singapore Pat. No. 51383, 66959, and
71979; European. Pat. Nos. 0 842 463 (96927260.8), 1 010 057 (98903671.0), 1 018
069 (98950708.2); Republic of Korea Pat. Nos. KR201211B1 and KR226206B1.
People’s Republic of China Pat. Application Nos. 98802801.8, 98809472.X and

96196739.0; Mexico Pat. No. 208141; Russian Federation Pat. No. 2206118; and
additional patents are pending worldwide”

• RSA™ is a registered trademark of RSA Data Security Inc.

• OPENWAVE™ is a registered trademark of Openwave Systems Inc.

• USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG-4

VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE DIRECTLY RELATED TO
(A) DATA OR INFORMATION ENCODED BY A CONSUMER FOR PERSONAL AND
NON-COMMERCIAL USE WITHOUT REMUNERATION; (B) DATA OR
INFORMATION (i) GENERATED BY AND OBTAINED WITHOUT CHARGE FROM A
CONSUMER NOT THEREBY ENGAGED IN A BUSINESS ENTERPRISE, AND (ii)
FOR PERSONAL USE ONLY; AND (C) OTHER USES SPECIFICALLY AND
SEPARATELY LICENSED BY MPEG LA, L.L.C.

• Helvetica is a registered Trademark of Heidelberger Druckmaschinen AG which may

be registered in certain jurisdictions.

• Powered by Mascot Capsule®/Micro3D Edition™

• ©2002 Music Airport Inc., http://www.music-airport.com/

• Java and all Java-based trademarks and logos are trademarks or registered

trademarks of Sun Microsystems, Inc in the U.S. and other countries.

• Copyright 2005 Aplix Corporation and eSOL Co., Ltd. All Rights Reserved.

• This Mobile Printing Ready product is designed to provide easy printing from mobile

phones. This product follows Mobile Imaging and Printing Consortium (MIPC)
guidelines version 1.0 for PictBridge.

• The Bluetooth

®

word mark and logos are owned by the Bluetooth SIG, Inc. and any
use of such marks by NEC is under license. Other trademarks and trade names are
those of their respective owners.

• This product contains ACCESS CO., LTD’s IrFront® Infrared communication software.

Copyright ©1996-2005 ACCESS CO., LTD

Before You Start

User’s manual conventions

The instructions in this user’s manual make use of the shortcuts selection except special cases.

The following markers are used throughout the user’s manual to attract your attention:

/ This type of paragraph will contain details of where to find information related to the topic in question.

2 This type of paragraph will contain information worth noting.

, This type of paragraph will contain important information.

☛ This type of description will contain procedures to operate your phone.

Menu shortcuts selection

The alternative shortcuts method of selection lets you jump straight to a menu or function without highlighting an icon and scrolling through the
intermediate menu options. The selection is made by pressing numbers which relate to the displayed menu options.

2 The instructions in this user’s manual make use of the shortcuts selection, except in special cases.

Reading the titles

Some titles in this manual contain information on how to access the functions. In these titles, M stands for , the numbers indicate the menu shortcut
numbers (see “Overview of menu function” on page x for details) and ... (three periods) indicate that there are more operations described in the
paragraph.

Reading the procedures

“Highlight” means to use the four way navigation keys (▲▼ ) to move the area emphasized with different colouring.
“Select” means to highlight an item and then press

.

Procedures are written omitting the verb “press”, except in some special cases.
For example, 1 2 means to:

☛ Start from the standby screen ➔ Press to display the Main menu screen

▼

▼

Display information

, The Liquid Crystal Displays (LCD) on your phone are manufactured using high-precision technology. Even so, the LCD may contain pixels

(dots) that fail to light or that remain permanently lit. Note that this is normal and does not indicate a problem with your display.

Status bar area

This area contains
icons which indicate the
battery strength, new
SMS/MMS message(s),
signal strength, etc.
(see page viii).

SK1/SK2

This area contains context
sensitive descriptions of the
Softkeys’ functions appropriate for
the current screen.

Shortcut number

Press the appropriate
number to jump
straight to a next menu.
The row colour is
changed when
selected (e.g. to
activate/deactivate a
facility).

Help icons

Displayed when you can use the
key represented by these icons
(see page viii).

Next menu icon

Displayed when you can
press or the shortcut
number to show the next
menu.

▼

Page scroll bar

Displayed when you
can press

▼ to scroll to

the next page.

Shortcut menu number

The current menu
number is displayed.

Menu title

Desktop icon area

This area contains the
automatically displayed
and the manually created
desktop icons. They
provide shortcuts to
certain items/functions.

Help area

This area contains clock
information and help
information appropriate
for the current screen
(e.g. key presses
remaining when
composing a message).

Parts and functions

Side up key

Side down key

Softkey 1 (SK1)

Celar (CLR)/Back key

Alphanumeric keys

Select ( ) key

End/on-off ( ) key

Softkey 2 (SK2)

Mouthpiece

Charger connector cover

Through-hole for straps

IR port

Earphone jack cover

Rear cover for battery

Speaker

Camera

LED/Light

2nd-LCD

Phonebook ( ) key

MENU ( ) key

Send ( ) key

Main-LCD

Earpiece

4 way navigation ( ) key

@

Keypad shortcuts

The following operations are available from the standby screen.

Key Operation that involves pressing a key

See

page

Operation that involves pressing and holding a key

See

page

Accessing the Main menu screen x Setting/Cancelling the Side key lock 21

SK1 Accessing the Message screen 28 Accessing the Msg type screen to create a new message 34

SK2 Accessing the Web browser 40 – –

Accessing the Phonebook list screen 45 – –

▲ Accessing the Phone modes screen 22 Setting the phone to Meeting mode/Returning to the previous mode 22

▼ Accessing the My data screen 59 Accessing the voice recall 8

Accessing the received calls list 12 – –

Accessing the missed calls list 12 – –

Accessing the dialled calls list 12 – –

Highlighting a desktop icon 19 – –

Ending a call or returning to the standby screen – Powering off 5

CLR

Cancelling the Cell Broadcast message display 39 Deleting all the automatically displayed desktop icons 19

Deleting character or returning to the previous screen – Deleting all characters when you enter text –

1 Entering phone numbers 6 Calling the Voice mail centre 52

2 to 9 Entering phone numbers 6 One-touch dial to the corresponding number in the phonebook(SIM) 8

0 Entering phone numbers 6 Entering + when you make an international call 14

# Entering # 6 Entering a pause –

Entering

6 Switching the ALS line 1/2 (If the SIM card supports ALS) 21

Accessing the volume control screen when your phone is open

21

▼

▼

LCD and displayed icons

Main-LCD

Indicates the battery level.

Indicates the battery charging status (fast, slow,
stop).

Indicates that there is a new SMS in your phone.

Indicates that there is a new SMS on the
network.

Indicates secured communication on WTLS in
WAP browsing.

(pink, blue)

Pink indicates that PDP Context is activated, and
blue indicates the connection with GPRS
network.

Indicates that Bluetooth is set to on, Bluetooth is
in operation, IR modem is set to on.

Indicates the line status (No ALS or ALS Line 1/
ALS Line 2).The icon with displayed in red
indicates that the ALS line 1 or 2 is unencrypted/
no ALS.

Indicates the signal strength level.

Appears when you are outside the service area.

Network name (indicated in orange when using

roaming service)

Desktop icons

See “Desktop icons” on page 19 for details

(red, green/red, green)

Indicates that new voice mail messages are on
the network (No ALS or ALS Line 1/ALS Line 1
and 2/ALS Line 2).

Indicates the call diversion is set.

Java™ application for the standby screen is
suspended.

Date

Day of week

Remote time

Local time

Indicates that you can use the options menu by
pressing .

Indicates that you can use the phonebook list by
pressing .

Indicates that the help display is available by
pressing when using SIM toolkit.

<When the camera/video view finder is in

operation>

Indicates single/burst mode (camera).

Indicates the video mode is on or the video is
recording.

Indicates that the self timer is on.

3

4

2

5

1

678 9

10

11

12

13

14

15

17

16

1

2

5

6

7

8

9

10

11

12

13
14

15
16
17

2

3

4

Indicates the brightness setting. The “+2” setting
is the brightest.

Indicates the zoom level.

<When the video preview is in operation>

Indicates the video mode is set to on, the video is
playing, on pause, fast forwarding, or rewinding.

Indicates the track information of the video (the
video only, the audio only, and the video and
audio).

Indicates the video is played in normal/enlarged
screen size.

Displays the current volume level. The 0 is mute
and 9 is the maximum.

2nd-LCD

Indicates the battery level.

Indicates

the battery charging status (fast, slow, stop).

Indicates that there is a new SMS in your phone.

Indicates

that there is a new SMS on the network.

Indicates that the SIM memory is full.

Indicates that the Inbox in your phone is full.

Indicates that there is an MMS on the server.

(red, green/red, green)

Indicates that a new voice mail message is on
the network (No ALS or ALS Line 1/ALS Line 1
and 2/ALS Line 2).

Indicates the Bluetooth is on, Bluetooth is in
active, IR modem is set to on.

<When 2nd-LCD is used as the camera

view finder screen>

Indicates the battery level.

Indicates

the battery charging status (fast, slow,

stop).

Indicates single or burst mode of the camera.

(blue, red)

Indicates that the video mode is on or the video
is recording.

Indicates the photo/video screen size.

Indicates that the self timer is on.

7

8

2

4

7

8

4

6

1

2

7

5

3

1

2

3

4

5

9

10

11

8

8

9

10

11

Overview of menu function

➡

➡

➡

➡

Standby screen

Main menu screen

CLR

or

SK2

The Main menu has a set of icons for its top levels of options which can be selected either using
a combination of the 4-way navigation key (▲ ▼

) and (menu selection), or just the

keypad (shortcuts selection).

2 The title of the selected option will be displayed in the Help area.
2 SIM toolkit icon is displayed only when your SIM card supports this function.
2 With the Main menu screen displayed, 0 to display your own number.

▼

▼

Key Main menu Second level menu

1 Settings Phone

Phone modes
Main-LCD
2nd-LCD
Power saving
Calls
Security
Network
Connection profile
Reset settings

2 Message Inbox

Drafts
Outbox
Sent

Key Main menu Second level menu

3 Web browser Internet

Bookmark
Snapshot
Alert message
Settings

4 Phonebook Lists

Information #
Call options

5 Camera Camera

Video recorder

6 My data Videos

Sounds
Pictures
MP3

Key Main menu Second level menu

7Java

™

Applications
Network setting
Resident setting
Storage info

8 Accessory MP3 player

Calculator
Clock alarm
Scheduler
ToDo list
Notepad
Voice memo
Currency
External connection
Synchronization

Getting Started 1

Basic Calls & Phone Use 6

Text Entry 16

Desktop icons 19

Settings (M1) 21

Message (M2) 28

Web browser (M3) 40

Phonebook (M4) 45

Camera (M5) 53

My data (M6) 59

Java™ (M7) 65

Accessory (M8) 67

Bluetooth (M891) 76

Emergency Services and Safety Precautions i

Before You Start iv

User’s manual conventions............................................. iv

Display information .......................................................... v

Parts and functions ......................................................... vi

LCD and displayed icons ............................................... viii

Overview of menu function .............................................. x

Getting Started 1

Preparing the phone ........................................................1

Standby and talk times .................................................... 4

Checking the battery........................................................ 4

Low battery alarm ............................................................4

Other battery alarms ........................................................ 4

Start-up ............................................................................ 4

Basic Calls & Phone Use 6

Making basic calls............................................................ 6

Ending a call .................................................................... 6

Receiving an incoming call ..............................................6

Unsuccessful calls ...........................................................7

Emergency calls .............................................................. 7

Last number redial ........................................................... 7

Call transfer ................................................................... 10

Multi-party calls.............................................................. 10

Recording a call ............................................................. 11

Scratchpad number ....................................................... 11

Call options (M43).......................................................... 11

Call settings (M16)......................................................... 13

International dialling codes ............................................ 14

Roaming ........................................................................ 15

Text Entry 16

Mode change ................................................................. 16

T9

®

English text input .................................................... 16

Normal text input............................................................ 17

Numeric input................................................................. 17

Key allocations............................................................... 18

Desktop icons 19

Settings (M1) 21

Phone (M11) .................................................................. 21

Phone modes (M12) ...................................................... 22

Main-LCD (M13) ............................................................ 24

2nd-LCD (M14) .............................................................. 24

Power saving (M15)....................................................... 24

Message (M2) 28

Message overview .........................................................28

Reading a message (M21)............................................. 29

Options menus............................................................... 30

Creating a message....................................................... 34

Cell broadcast (M26)...................................................... 39

Web browser (M3) 40

What can I download .....................................................40

Web settings ..................................................................40

Logging on to WAP site .................................................42

Other features ................................................................ 43

NEC Web site ................................................................43

GPRS dial up .................................................................44

Phonebook (M4) 45

Phonebook types ...........................................................45

Accessing your phonebook (M4) ...................................46

Phonebook list Options menu ........................................47

Personal data Options menu .........................................51

Voice mail (M417) ..........................................................52

Camera (M5) 53

Notes on using the camera ............................................53

MP3 (M64) ..................................................................... 62

File selector Options menu ............................................ 62

Java™ (M7) 65

Applications (M71) ......................................................... 65

Network setting (M72).................................................... 65

Resident setting (M73)................................................... 65

Storage info (M74) ......................................................... 66

Accessory (M8) 67

MP3 player (M81) ..........................................................67

Calculator (M82) ............................................................68

Clock alarm (M83).......................................................... 68

Scheduler (M84) ............................................................69

ToDo list (M85) ..............................................................70

Notepad (M86) ............................................................... 72

Voice memo (M87)......................................................... 73

Currency (M88) .............................................................. 74

External connection (M89) ............................................. 74

Synchronization (M80) ................................................... 75

Bluetooth (M891) 76

Using Bluetooth connection ...........................................76

IR Data Exchange 79

Memo

Getting Started

Preparing the phone

Before trying to use your phone, make sure that a valid Subscriber Identity Module (SIM) card is inserted and the battery is charged.

SIM card

Before using your phone, you must sign-up with one of the digital network service providers. In addition to your subscription details you will receive a
personal SIM (Subscriber Identity Module) card which is inserted into your phone.

If the SIM card is removed, the phone becomes unusable until a valid SIM card is fitted. It is possible to transfer your SIM card to another compatible
phone and resume your network subscription. The screen on your phone will display appropriate messages if no SIM card is fitted.

, If the phone, or the SIM card, is lost or stolen then you should contact your service provider immediately in order to bar it from use.

2 The phone supports a number of languages and the keyboard symbols have been chosen for world-wide operation.
2 The digital technology of your phone helps to ensure that your conversations are kept secure.
2 The SIM card contains personal data such as your electronic phonebook, messages (see “Message (M2)” on page 28) and also details of the network

services you have subscribed to. The phone will not work (except for emergency calls on some networks) unless a valid SIM card is fitted.

, Be sure to turn the phone off before inserting and removing a SIM card. Otherwise damage to the SIM card can occur.

Inserting a SIM card

, Be sure to turn the phone off before removing the battery pack.

☛ While pressing down the areas marked with of the rear cover as indicated by arrow ➀, slide the rear cover about 3 mm in the direction of

arrow ➁ with your finger tip. Then, lift the cover up in the direction of arrow ➂ to remove it.

☛ Lift the finger tab of the battery pack up in the direction of arrow ➃. Then lift the battery pack out in the direction of arrow ➄.
☛ With the metal part facing down, insert the straight end of the SIM card under the holder in the direction of arrow ➅. Slide the SIM card all the way

until it reaches the end.

, Be careful not to damage electric parts of the SIM holder when inserting a SIM card.

.

, If the SIM card is not fully inserted when the battery is replaced, damage to the SIM card can occur.

/ If the SIM card is already fitted, see “Start-up” on page 4.

Removing a SIM card

☛ With the battery removed, push the short and straight end of the SIM card with your thumb to slide it gently in the direction of arrow ➆ ➔ Lift the

SIM card after it is completely removed from the holder.

, Be careful not to damage electric parts of the SIM holder when removing a SIM card.

Rear cover

About 3 mm

Battery

Finger tab

Holde

r

SIM card

Tabs

Slots

About 3 mm

Check that there is no ga

p

between the rear cover
and the phone body.

Charging the battery

Before trying to use your phone, insert the phone’s battery and connect the NEC battery charger (AC adapter) supplied with your phone to a suitable
mains power socket.

☛ Pull open the charger connector cover gently.

, Be careful when handling the charger connector cover. Do not pull strongly.

☛ With the arrow marks of the charger plug facing up, hold the buttons on both sides of

the charger plug with your thumb and index finger.

☛ Press the buttons as indicated by the arrow marks on the charger plug and insert the

plug into the charger connector.

, Make sure to insert the charger plug with the arrow marks facing up. Otherwise,

damage to the charger connector can occur when disconnecting the charger plug.

2 If your phone is turned on and charging starts, the battery charging icon will be

displayed. LED will turn on in red while charging. When charging is complete, the LED
will turn off.

2 You are recommended to switch off the phone while charging. If you need to receive

calls, your phone can be switched on and left in standby while being charged,
although the total time taken to charge is then increased.

☛ After the charging is complete, press the buttons of the charger plug as indicated by the

arrow marks on the charger plug (➀) and gently pull straight out of the charger connector
(➁).

, Make sure to press both buttons when disconnecting the charger plug from the

charger connector. If you pull the charger plug forcibly without pressing the
buttons, damage to the charger connector can occur.

The icons show the charging status of battery.

Fast battery charging Slow battery charging while the phone is in use Battery charging stopped due to overheat

, Using any battery pack, AC adapter, vehicle power adapter (option) not specified by NEC for use with this phone can be dangerous and

may invalidate any warranty and approval given to the cellphone. Do not leave the charger connected to the mains supply when it is not

Charger connector

Charger plug

Press

Press

Pull straight

Make sure to press both buttons and gently pull
the charger plug straight.

Charger connector

Charger plug

Arrow marks

Press

Press

Make sure to hold the charger plug with the arrow
marks facing up and press both buttons.

, IMPORTANT BATTERY CHARGING INFORMATION

Charging a very low battery

The battery’s charge continues to drop after the low battery warning is displayed. In extreme cases where the battery is left uncharged for some
considerable time after this warning, a trickle charge is used to slowly top-up the battery to the safe level at which the fast charging can begin. The
phone can be in trickle charge for a few minutes before the fast charging starts.

Standby and talk times

Your phone works closely with the network you are using to provide the services you need, and the standby and talk times achieved will depend on how
you use the phone and choices made by the network operator.

In particular, factors such as your location within the network, the frequency at which this location is updated, the type of SIM card you have, your
reception of area messages or cell broadcast messages and the use of full rate or enhanced full rate speech, will affect both standby and talk times.

Checking the battery

☛ Check icon at the top of the standby screen.

The number of blocks on the icon shows the charge of your battery pack.

Full battery power Partial battery power Low battery power Battery empty

Low battery alarm

When the battery voltage falls below the working level, a low battery warning is displayed on the screen accompanied by LED illumination and a short
tone along with an empty battery icon. The phone will automatically power down shortly afterwards.

2 Please charge the battery as much as possible when the battery is very low.

Other battery alarms

Your phone may display warnings when the battery temperature is too high, or the voltage of the battery or the charger is over the appropriate level.
Follow the instruction given by these warnings immediately.

Switching the phone off

☛

Hold down until the display shows the switch off message.

PIN code

The SIM card issued by your service provider has a security feature called PIN code protection. The Personal Identification Number (PIN) is a number
put on to the card by your service provider, and is 4 to 8 digits long. Some service providers supply SIM cards which will cause your phone to prompt for
a PIN code when it is turned on. If this is the case, enter your code with the phone’s keypad. If you insert a SIM card other than your own, information
such as call logs may be lost (see “Security (M17)” on page 25 for details).

Basic Calls & Phone Use

Making basic calls

You make a simple call in the same way as you would with a normal phone, except that you need to press after entering the area Subscriber Trunk
Dialling (STD) code and the phone number. To make international calls, you must first enter the international dialling code (see page 14).

2 Use the full STD area code even if you are calling to a person in the same town. If the numbers are too long to be displayed within one line, after

pressing , excess part is deleted and ‘...’ is added at its end.

2 The main-LCD display shows the strength of the radio signal that links your phone to the network. The maximum signal strength is shown by 4 shaded

blocks and the minimum signal strength by 1 block.

Starting a call

☛

Key in the phone number. Check the number on the display ➔ or SK1 to send the input number to start the call

☛ Before the other party answers the call, you can end the call by pressing briefly, pressing SK2 or closing your phone. When you use the

headset, you can also end the call by pressing and holding the button on it.

2 When connecting a wired headset and Bluetooth headset at the same time, the wired headset will not work.

When the call is sent, the screen displays the number called, the name stored in the phonebook and a connection graphic or a Calling Line Identification
(CLI) picture that has been allocated to the number called (see page 50).

Correcting mistakes

Use the and to move the cursor and then CLR to clear individual digits, or hold down CLR to completely clear a phone number.

Ending a call

☛ While talking, SK2 or briefly, or close your phone. The phone returns to the standby screen.

2 If is held down, your phone will turn off.
2 When you use the headset, you can also end a call by pressing and holding the button on it.
2 When connecting a wired headset and Bluetooth headset, the wired headset will not work.

▼

▼

Accepting an incoming call

☛ While receiving an incoming call, or SK1

2 When you use the headset, you can also accept an incoming call by pressing the button on it.
2 When connecting a wired headset and Bluetooth headset, the wired headset will not work.
2 When Auto answer function (see page 23) is set to on and a headset is connected to the phone, the incoming call is automatically accepted after

several rings.

2 You can accept an incoming call by opening your phone, when Fold answer function (see page 21) is set to on.
2 You can set your phone to answer a call when any key is pressed (see “Any key answer” on page 21).

Rejecting an incoming call

☛ While receiving an incoming call, or SK2 briefly or close your phone.

2 When you use the headset, you can also reject an incoming call by pressing and holding the button on it.
2 You cannot reject a call by closing your phone when the headset is connected.
2 When connecting a wired headset and Bluetooth headset, the wired headset will not work.

If your phone receives a call and you do not answer it, the main-LCD will display a desktop icon of the phone number (or the name if stored) of the caller
(if available).If your phone is closed, the 2nd-LCD will also display a missed call icon, and you can display the details by pressing Side up. This
information is stored in the missed calls list. Up to 20 missed calls are stored in this list.

2 If you are making a call, the phone gives priority to receiving a call unless you have already pressed .

/ See also: “Call diversion (M161)” on page 13 and “Call waiting and holding (M162)” on page 14.
/ See also: “Call options (M43)” on page 11.

Unsuccessful calls

If dialled call is not successfully connected, the display will give an appropriate message.
If your phone has the auto redial function activated, the number will be automatically called again after a short delay (see page 14).

Emergency calls

The standard emergency number of 112 can be used.

One-touch dial

One-touch dial for the phonebook (SIM) is available by pressing and holding the number keys between 2 and 9.

2 A number for the One-touch dial corresponds to the location number in the phonebook (SIM).
2 One-touch dial is available only for the phone numbers with the location number 2 to 9 stored in the phonebook (SIM).

Fast dialling

You can make a call to the phone number in the phonebook (Phone/SIM) with just a few press of button.
To fast-dial the phone number in the phonebook (SIM), use the following procedure:

☛ From the standby screen, key in the Location number of a personal data in the phonebook (SIM) ➔ # ➔ The corresponding personal data is

displayed.

☛ to dial the phone number.

To fast-dial the phone number in the phonebook (Phone), use the following procedure:

☛ From the standby screen, key in the Location number of a personal data in the phonebook (Phone) ➔ ➔ The corresponding personal data is

displayed.

☛ Use the and keys to choose the phone number (if there are more than one), then to dial the phone number.

Displaying your own phone number (M0/M416)

☛ 0 or 4 1 6

Voice recall

You can store up to 10 voice recall recordings which can be allocated to a personal data stored in the phonebook (Phone). To store the voice recall
sound, see “Voice recall functions” on page 50. To use the voice recall function, use the following procedure:

☛ Press and hold ▼

▼

▼

Options menu (during a call)

☛ During a call, to display the options menu

2 Depending on the conditions, some options may be displayed in gray and not be available.

Putting a call on hold

☛ To put the received or dialled call on hold, SK1 or 2. To retrieve the call, SK1 or 2 again.

Mute

No. Options menu (during a call)

1 Main menu Displays the Main menu screen. See “Overview of menu function” on page x for details.

2 Hold/Retrieve Puts the call(s) on hold or retrieves the call(s).

3Mute/Unmute Mutes or unmutes your voice to all active calls.

4 Transfer call Enables to transfer the call and connect other parties.

2 After transferring the call, your call will be dropped.

5 Add to conference Merges calls and makes a multi-party call.

6 Private call Makes a private call to the highlighted party within the multi-party call.

7 Record call Records the call while talking.

8 Disconnect party Disconnects the highlighted party.

9 Switch call to Bluetooth/

Switch call to phone

Switches the audio path state of the call.

2 You can also switch call to Bluetooth or phone by pressing and holding #.
2 This option is available only when the Bluetooth device is connected to the phone.

0 Bluetooth On Activates the Bluetooth device.

Call transfer

When you have an active call and a held call, you can transfer the call and connect the two parties, then you can drop from the line while leaving those
two calls active.

☛ To transfer the call, 4.

2 After dropping from the call with the other two parties, if you have a call waiting, you can proceed the call with it.

, Call transfer facility is SIM dependent.

Multi-party calls

If your SIM card is multi-party enabled, you can make a conference call to more than one caller. To create the multi-party calls, at least 3 parties, including
the host, are needed.

Receiving the second call

☛

SK1 or to accept the second call ➔ SK2 or 5 to merge both calls to initiate a multi-party call.

2 When you accept the second call, the first call will be put on hold.

Making the second call

☛

SK1 to put the first call on hold ➔ Key in the phone number ➔ SK1 or to make the second call ➔ After the second participant answers, SK2
or 5 to merge both calls to initiate a multi-party call.

Putting the multi-party calls on hold

☛

SK1 or 2 to put all calls on hold ➔ To retrieve the call, SK1 or 2 again.

2 You can put the multi-party calls on hold only when you are a host of the multi-party calls.

Making a private call

While on the multi-party call, you can make a private call to a specific party.

☛ To make a private call, highlight the desired party you want to make a private call to ➔ 6
☛ To end a private call and return to the normal multi-party call ➔ 5

Recording a call

You can record the conversation during the call.

☛ During a call, press and hold ▼ or 7 to display the Voice memo screen ➔ SK1 to start the recording ➔ SK1 to pause and SK2 to stop the

recording

2 To play the recording, see “Recording/playing voice memo or setting speaker” on page 73.

Scratchpad number

Your phone has a scratchpad facility that enables you to take down a phone number during a call and then make a call to it when you have finished. This
scratchpad number can be stored in memory for future use.

Noting & calling a scratchpad number

☛

During a call, key in the number to be placed in the scratchpad. It will be shown on your phone’s screen ➔ when the call is finished. The number
will still be displayed ➔ to dial the displayed number.

Call options (M43)

From Call options, you can display the list of missed, received and dialled calls, the duration of the last call made and all calls, charge information and
the redial blacklist.

☛ 4 3 to display the Call options screen.

No. Call options

1 Missed calls Displays the list of missed calls. You can also access this function by pressing from the standby screen.

2 Received calls Displays the list of received calls. You can also access this function by pressing from the standby screen.

3 Dialled calls Displays the list of dialled calls. You can also access this function by pressing from the standby screen.

4 Last call duration Displays the duration of the last call made on your phone.

☛ SK1 to reset the display to zero.

▼

▼

2 Depending on the conditions, some options may be displayed in gray and not be available.

Display missed/received/dialled calls Options menu (M431M/M432M/M433M)

☛

or 4 3 1 for missed calls, or 4 3 2 for received calls, or or 4 3 3 for dialled calls.

☛ Highlight a number in the list ➔

6Charge info Displays the charge information (Advice of Charge - AoC).

, The AoC facility is SIM card and network dependent.

2 To reset the display to zero, set the maximum charges or edit the unit price, you may be prompted to enter

the PIN2 code.

1 Total charge Displays the total charge.

☛ SK1 to reset the display to zero.

2 Maximum

charge

Displays the maximum charge.

☛ Key in the maximum number of units allowed ➔ SK1

3 Unit price Displays the unit price.

☛ Highlight the whole number (integer), the decimal number or the currency field ➔ Key

in the required value for the whole number and decimal number fields. For the
currency field, key in the currency type using a maximum of three characters ➔ SK1

7 Redial blacklist Displays the numbers in the blacklist.

2 If dialled call is not successfully connected (e.g. number busy), the auto redial facility will be offered (see

page 14). If you have set auto redial and the call still fails 10 times, the number called will be added to the
blacklist.

No. Missed calls/Received calls/Dialled calls Options menu

1Call Calls the current number.

No. Call options

▼

▼

2 Depending on the conditions, some options may be displayed in gray and not be available.

Call settings (M16)

From the Calls screen, you can change various call settings: the call diversion, call waiting and holding, auto redial, and line ID.

Call diversion (M161)

Setting Call diversion

☛ 1 6 1 ➔ or select the type of call you wish to divert from Speech, Data or Fax.

2 There will be a delay while your phone checks its divert status with your network.

☛ Highlight one of the conditions ➔ When the phone number field of a divert condition is highlighted, either enter the phone number to divert to, or

delete any existing phone number.

☛ If you have made any mistake, highlight the appropriate field ➔ SK1 to clear any mistakes.
☛ If the settings are correct,

, There will be a short delay while the network sends the divert status of your phone.
, There may be an additional charge for this service depending on your network.
, There may be unavailable settings depending on your network.

Call diversion edit options menu

☛ Highlight the required edit field ➔

6Info Displays information on the current number.

7 Add desktop icon Creates a desktop icon of the selected number.

8Items/Page Selects either to display 4 or 8 phone numbers in one screen.

No. Call diversion edit options menu

No. Missed calls/Received calls/Dialled calls Options menu

▼

▼

Call waiting and holding (M162)

This facility informs you that another call is being made to your phone while an existing call is in progress.

Setting up call waiting

☛ 1 6 2 ➔ 1 1 to activate, 1 2 to deactivate the call waiting, or 2 to check the status of call waiting.

Using call waiting

☛ If you are on a call and another comes in, you will be alerted by a beep in the earpiece ➔ SK1 to accept the incoming call.

☛ To switch the calls, SK1
☛ To merge the calls, SK2 (see “Multi-party calls” on page 10).
☛ To end the current call,

☛ To retrieve the held call SK1

Auto redial (M163)

With the auto redial facility, your phone will redial a number up to 10 times if the first attempt fails. A tone will be heard at each redial attempt. Your phone
cannot connect a call if the other party is busy or if there are network problems. Pressing SK2 during a redial attempt will abort it.

☛ 1 6 3 ➔ 1 to activate or 2 to deactivate the auto redial facility.

2 If the tenth attempt still fails, the number will be added to the blacklist (See “Redial blacklist” on page 12).

Line ID (M164)

, The line ID (identification) facility is network dependent.

The line ID facility enables you to choose whether or not to send your own phone number when you make a call
and also whether or not to display a caller’s phone number when you receive a call.

☛ 1 6 4 to display the Line ID screen with a ✔ over an activated line and a ✘ over a deactivated line.
☛ To set the status of each line (see the table on the right), highlight a line (the line will flash when selected).
☛ SK1 to set the line identification on or off ➔ to save the current settings.

International dialling codes

Line type Setting

Outgoing Send own #

Show connected #

Incoming Show Incoming #

Return own #

Roaming

, You will be charged for calls forwarded to you while roaming.

The roaming facility enables you to use your phone in many parts of the world and pay all charges through your normal service provider. Your network
operator usually has agreements with named networks in other countries so that automatic roaming can take place with these named networks. The
phone also allows you to set network preferences of your own.

When dialling, you will need to add the international access codes if required. So, storing all numbers with the codes (such as +44 for UK) is helpful (see
“Entering international dialling codes”).

2 Before leaving your home country, you should select any preferences such as bar calls or call diversion.

Setting Automatic or Manual network selection (M181)

☛ 1 8 1 ➔ 1 to select the automatic mode or 2 to select the manual mode.

, Before you manually select a network, ensure it is covered under the agreement you have with your service provider.

New search (M182)

☛

1 8 2 to search the available networks➔ Highlight the desired network ➔ to connect to it.

Viewing/editing network list (M183)

, Before editing your network list, please consult with your service provider.

☛ 1 8 3 to read the network list in the SIM memory ➔ Highlight the required network ➔

2 Depending on the conditions, some options may be displayed in gray and not be available.

No. SIM list Options menu

1Add Adds a new network to the list.

2Move Moves the highlighted network within the list.

☛ Use ▲ and ▼ to move the network ➔ SK1

3Remove Deletes the highlighted network.

Text Entry

This section describes how you enter text.

Mode change

☛ With a text entry screen displayed, SK1 to change the text entry mode.

2 Depending on the Language setting (see “Language” on page 22 for details) the type of text input mode you can use varies:

• English mode: T9

®

English text, Normal text (ABC), Numeric input

T9® English text input

Your phone incorporates T9® Text Input, enabling fast, easy and intuitive text input. For each letter to be keyed in, you only need to press the
alphanumeric key once. The screen will display the word you may require based on the internal English dictionary of your phone.

☛ With a text entry screen displayed, SK1 until the entry mode is T9

®

English input.

i) For example, to enter “Good”:

☛ 4 6 6 3, and then 0 to confirm the word.

ii) To enter “Peter is good”:

☛ to shift to upper case (for one letter). You will see a green arrow in the Help area.
☛ 7 3 8 3 7 to display “Peter”, and then 0 to confirm.
☛ 4 7 to display “is”, and then 0 to confirm.
☛ 4 6 6 3 to display “good”, and then 0 to confirm and the sentence is completed.

Key Function

0 Confirms a word and inserts a space.

1 Inserts a period or a single quote as in “Let’s”, “we’re”, “it’s”, etc.

SK1(List) Displays the list of other matching words.

Normal text input

☛ With a text entry screen displayed, SK1 until the entry mode is Normal text (ABC) input.
☛ Use alphanumeric keys to enter letters. For example, to enter “e,” press 3 twice; to enter “f,” press 3 three times. For other functions, see the table

below.

2 When you are in the Normal text (ABC) input, any word entered that is not in the T9

®

dictionary will be added automatically.

2 If you have made a mistake, use ▲ ▼ to place the cursor to the left or the right of the incorrect character (depending on the Clear mode setting,

see page 39 for details) and then CLR.

2 When entering normal (ABC) text, and the character you require is displayed, use to move to the next character position (if you wait for more than

1 second, the cursor will move one character to the right automatically).

CLR Deletes any character.

Toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case).

(press and hold) Press and hold to activate the highlight mode (see “Highlight mode” on page 38).

# Activates symbol mode when no word is highlighted.

Key Function

Toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case).

(press and hold) Press and hold to activate the highlight mode (see “Highlight mode” on page 38).

0 Inserts a space.

0 to 9 (press and hold) Inserts the number.

CLR Deletes any character.

or Places the cursor.

# Activates symbol mode.

Key Function

▼

▼

▼

▼

▼

Key allocations

Whenever you need to enter text (for messages, storing names with numbers, etc.), successive presses of an alphanumeric key will display different
characters. Pressing in T9

®

English text input or Normal text (ABC) input toggles between lower case, shift (upper case for one letter) and caps lock

(permanent upper case). When a text entry screen is displayed, pressing SK1 enables you to select Normal text input (ABC), T9

®

Text input (T9) or

Numeric input (123).

2 Depending on the types of text entry screens, not all types of text entry modes are available.

Symbol mode

In the symbol mode, pressing each key will input a symbol according to its position on the Symbols screen. By pressing or holding # in a text entry mode,
the Symbols screen will be displayed. Use ▲ and ▼ to select the row, and then press the appropriate number on the column of the required symbol.

Desktop icons

Desktop icons are shortcuts to functions or items. You can activate a desktop icon on the standby screen (desktop) in stead of following the menu and
pressing the shortcut numbers.

The desktop icons are displayed in two rows on the standby screen. See “LCD and displayed icons” on page viii for the actual location of the desktop
icon area.

There are two types of desktop icons: the automatically displayed and the manually created.

Automatically displayed desktop icons

The following automatically displayed icons are displayed on the upper row of the desktop icon area:

2 You can delete all the automatically displayed icons by pressing and holding CLR on the standby screen.
2 If you turn the phone off, all the automatically displayed desktop icons are deleted.

Manually created desktop icons

The following manually created icons are displayed on the lower row of the desktop icon area

Icon name Image Description

Missed call Displayed when there is a new entry in the Missed calls list.

Missed message Displayed when there is a new message you have not acknowledged.

Icon name Image Description

Phone number Displays a dialer screen with the registered phone number displayed.

Message Creates a new message to the registered phone number or Email address.

Picture Displays the image file.

Note Displays the note.

Camera Displays the camera view finder screen.

Creating a desktop icon manually

☛

Highlight the required function (Camera/Video/MP3 player/Calculator/Clock alarm/Scheduler/ToDo list/Notepad/Voice memo/Currency/Bluetooth)
or display the item (image file/note file/phone number/Email address).

☛ For functions, SK1
☛ For items, to display the Options menu and select Add desktop icon (for an image/note file, this menu is under Use item)

2 For Camera/Video/MP3 player, you can also display the Options menu and select Add desktop icon (for Camera/Video, this menu is under

Other settings).

2 You can create up to 10 desktop icons.
2 If you have more than 5 desktop icons, an arrow will be displayed to indicate that you can scroll for more icons.
2 The phone number or Email address desktop icon data will not be updated when the original data is modified. Delete the old desktop icon and

create a new one in such a case.

2 When you create a desktop icon of an image file or notepad file, the file will be automatically protected. The default title will be the file name. Even

if this title is changed, the original file name will remain the same.

2 Each manually created desktop icon has a title that you can edit.

Activating a desktop icon

☛

➔ Highlight the required desktop icon ➔

2 If you do not press any key for three minutes after highlighting a desktop icon, the highlight is cancelled and the screen goes back to the normal

standby screen.

2 If you activate an automatically displayed desktop icon, it will be deleted automatically.

Desktop icon Options menu

☛

Highlight a desktop icon ➔

Voice memo recorder Displays the New record screen for Voice memo.

Currency Displays the Currency screen.

Bluetooth Displays the Bluetooth screen.

Icon name Image Description

Settings (M1)

Phone (M11)

☛ 1 1

No. Phone

1 Voice volume Adjusts the sound volume output from the earpiece.

☛ Use ▲ ▼, Side keys or alphanumeric keys (0 to 9) to adjust the volume.

2 You can also press the Side keys to display the volume control screen and to adjust the volume setting.
2 During a call, you can press the Side keys to adjust the setting of the volume as required.
2 When you change this setting while a headset is connected, the changed volume will be valid only when you have

a headset connected.

2 While using a Bluetooth headset, you cannot change the volume.

2Answer

options

1 Any key answer On: Any key (except , SK2, the Side keys) is valid to answer a call.

Off: Only and SK1 are valid to answer a call.

2 Ring silencer On: Pressing one of the Side keys stops the ringer sound and the vibrator while receiving a

call with the phone closed.

2 This function cannot be used if the Side keys are locked.

3 Fold answer On: You can answer an incoming call by opening your phone.

3 Side key Disable: Side keys are locked while your phone is folded.

2 You can also lock/unlock the Side keys by pressing and holding on the standby screen.

4ALS setup , The Alternate Line Service (ALS) facility is SIM card and network dependent.

If your SIM card supports ALS, you can setup which line to use for Outgoing call or Voice mail.

Phone modes (M12)

Your phone can be set to one of the following modes: Normal mode, Meeting mode, Pocket mode or Car mode.

5Clock 1 Show clock Sets to display the local time, both the local and remote times or no time on the main-LCD.

2Set time Sets the time for the local or remote time.

3Set date Sets the date.

4 Set date format Selects the date display format.

5 Set time format Selects the time display format from 12 hour or 24 hour.

6Set timezone Sets the timezone. (A ✔ is placed on the currently selected timezone.)

☛ Highlight the required timezone ➔ SK1 to save the change.

2 If the highlighted timezone has Daylight Saving, a check box will be displayed at the

bottom of the screen. to activate (✔)/deactivate the setting.

7 Set start day Selects whether to start the week on Sunday or Monday.

2 This setting affects the functions related to the day of the week, such as Scheduler. (See

“Scheduler (M84)” on page 69 for details.)

6 Language Selects the language the phone displays.

2 When you have switched the language to be displayed, please wait until the new setting becomes active.
2 Even if you change the language settings, some names, such as that of desktop icons and pre-set folders in My

data, do not change.

7LED Selects the Light Emitting Diode (LED) colour for incoming calls/SMS/MMS (including Email) or during a call.

2 If the personal setting or the Group setting for the LED colour is also set in the phonebook, it has priority over this

LED setting. (See “Allocating a LED colour” on page 50 for details.)

8 Earphone type Selects the earphone type from Stereo or Monaural, depending on your earphones (headset).

No. Phone

2 For any volume setting, use ▲ ▼, Side keys or alphanumeric keys (0 to 9).
2 When you change any volume setting while a headset is connected, the changed volume will be valid only when you have a headset connected.

No. Phone mode setting

1 Ringer Selects the Sound, Video or MP3 for incoming calls. (See “Sounds (M62)” on page 59, “Videos (M61)” on page 59

or “MP3 (M64)” on page 62 for details.)

2 If the Video is set, it will sound and will be displayed regardless of the CLI picture/video setting for the personal

data in Phonebook. (See “Allocating a picture or video as a CLI” on page 50.)

2 Ringer volume Sets the sound volume for incoming calls.

2 While receiving a call with your phone open, the ringer volume can also be adjusted by pressing the Side keys.
2 While using a wired headset, you can set the volume for the wired headset. The volume settings for the wired

headset and the speaker of the phone are saved individually.

2 While using a Bluetooth headset and a Bluetooth hands-free kit, however, the volume setting for the speaker of

the phone is used.

3SMS tone Selects the ringtone for incoming SMS messages. (See “Sounds (M62)” on page 59 for details.)

4 SMS tone volume Sets the sound volume for incoming SMS messages.

5 MMS tone Selects the ringtone for incoming MMS or Email messages. (See “Sounds (M62)” on page 59 for details.)

6 MMS tone volume Sets the sound volume for incoming MMS or Email messages.

7 Key tone Turns on/off the key tone.

8 Service tone Turns on/off the service tone.

9 Alarm volume Sets the sound volume for Clock alarm and Schedule alarm.

0Vibrator Turns on/off the vibrator function.

Earphone setting Selects the sound output from Earphone & Speaker or Earphone.

Main-LCD (M13)

☛ 1 3

2nd-LCD (M14)

☛ 1 4

Power saving (M15)

No. Main-LCD

1 Greetings Selects the greeting which is displayed on the main-LCD during phone start-up from No greeting, Text or Animation.

☛ If you select Text greeting, SK1 to edit the greeting text. Key in a greeting text and .

2 Wallpaper Selects a picture or video file to use as the background for the main-LCD.

3 Main menu style Selects and resets the background and icons for the Main menu screen.

4 Colour style Selects the phone’s colour theme.

No. 2nd-LCD

1 Clock/Event display Selects which items to display on the 2nd-LCD from Clock & Event, Clock only, Event only or Off.

2 Wallpaper Selects a picture file to use as the background for the 2nd-LCD.

3 Clock selection Selects the type of clock to be displayed on the 2nd-LCD.

2 When selecting Digital 2 clock, no icon will be displayed in the standby screen of the 2nd-LCD.

4 Incoming call No. Turns on/off the function to display the incoming call number on 2nd-LCD.

5 Contrast Sets the contrast level of the 2nd-LCD.

☛ Use ▲, ▼ or Side keys to adjust the contrast. The contrast gauge is displayed on the 2nd-LCD.

Calls (M16)

☛ 1 6

/ For settings provided on the Calls screen, see “Call settings (M16)” on page 13.

Security (M17)

☛ 1 7

The security settings will help to protect your phone from improper and unauthorized use. You may be required to enter one of the five codes (shown
below). When the phone prompts you for one of these codes, key in the appropriate number.

• PIN code (provided by your network service provider to protect your SIM card if it is stolen)

• PIN2 code (provided by your network service provider for charge information and Fixed dialling services protection)

• PUK code (personal unblocking key in case you forget PIN code)

• PUK2 code (personal unblocking key in case you forget PIN2 code)

• Security code

, If you forget any of these codes, ALWAYS contact your service provider as they are the ONLY source for your codes.

PIN code

Your phone can be set up so that your PIN code must be entered at power up before the phone can be used at all. If the PIN code is not entered, not
even incoming calls can be answered. Entering your PIN code incorrectly 3 times (not necessarily in the same session) will invalidate the correct PIN
code. In such a case you will have to contact your service provider for a PUK code to unblock your SIM card.

2 Some SIM cards are set up so that PIN number entry cannot be turned off.

2 Function key LED Selects whether to flash the LED of SK1 and SK2 when the main-LCD and its backlight are turned off.

2 If the selected mode is Car mode or the camera view finder screen is displayed, the main-LCD backlight will

always be on.

No. Power saving

Network (M18)

No. Security

1Change PINs Changes the PIN or PIN2 code (PIN activate setting must be turned on to change the PIN code).

2 PIN activate Turns on/off the PIN code entry required at starting up the phone.

3 Change security

code

Changes the security code which is used to set some of functions and unlock the Personal Information Manager
(PIM) features.

2 The default setting of the security code is “0000”.

4 Phone lock Turns on/off the Phone lock function which will lock the phone: you can only make emergency calls or enter the

security code. After entering the correct security code, you can use the phone normally.

2 Upon power-up, you are prompted to enter the security code if the Phone lock was active when the phone was

powered down.

5 Bar calls You can bar the following calls made/received on your phone: all outgoing (dialled) calls, international outgoing

(dialled) calls, international outgoing (dialled) calls except to home, all incoming (received) calls or Incoming
(received) calls when roaming.

, Bar calls facilities are network services and may require a password.

1 Change settings ☛ Highlight the type of restriction and the call type, and then ➔ to save changes.

☛ Key in your bar calls password to verify user identification to the network ➔ SK1 to

confirm and save changes to the network.

2 The selected settings have red bars over their icons.

2 Set password Changes the bar calls password.

6 Fixed dialling Turns on/off the fixed dialling which restricts the use of dialled number to only the Fixed Dialling Numbers (FDN).

, The FDN facility is network dependent.

/ See also: “Fixed dialling numbers (FDN)” on page 46.

Reset settings (M10)

☛ 1 0

This function will reset your phone to its factory settings.

, By restoring the factory settings, any changes you have made to your phone EXCEPT the following will return to the factory settings (the

following data/settings will not be reset):

• Settings: Set time for Local time, Set date, Language, all settings in Calls other than Auto redial, all Security settings other than Change security

code, SIM list settings in Network.

• Call options: Information in Charge info.

• Phonebook: All Phonebook entries. The settings for Groups.

• Accessory: All Schedule, ToDo, Notepad and Voice memo entries. All the settings other than Clock alarm, Play list for MP3 player, View events for

Scheduler, Sort for ToDo, and Timer setting and My phone settings for Bluetooth.

• Web browser: All Bookmarks, Saved pages and WAP alerts. All the WAP related settings.

• Java™: All the Java™ applications.

• Message: All the stored messages. The settings for SMS centre, Validity period for SMS and Language for Cell Broadcast.

• My data: All stored files.

Message (M2)

Message overview

Message services

Your phone supports the following messaging services:

• Short Messaging Service (SMS) allows you to send short messages (160 half-pitch characters max.) to one or more phone numbers. To send an

SMS message, the destination phone number must be a mobile phone with an SMS service subscription. SMS service also supports Enhanced
Messaging Service (EMS) for which the maximum length of the message you can send depends on the number of linked messages (maximum of
10 linked messages are available).

• Email allows you to send messages with attachments to not only other cellphones but also to PCs and other devices that use Email addresses.

Attachable files include texts, sounds, pictures, animation, and videos. There are two types of Email server: POP3 server is used when receiving
Email messages and SMTP server is used when sending Email messages.

• Multimedia Messaging Service (MMS) is a service that allows you to send messages with multimedia files attached. You can attach image, sound

and video files to an MMS message. When you receive an MMS message, you will be notified by a message from the MMS centre. You can either
automatically or manually receive the contents of an MMS message.

, The Message Services are network dependent.

Sending/Receiving messages

While a message is being sent or received, a name (if a name has been stored with the number in your phonebook) or a number will be displayed.
The received messages are stored on the SIM card or in your phone memory. When you receive a message, your phone will ring or beep during a call,
the message icon will be shown on your phone’s display and its LED will glow.

2 Please delete the unnecessary messages in the folders from time to time. The phone cannot receive any messages when the Inbox folder is full.

Message screen

☛

SK1 or 2 to display the Message screen

☛ To create a new message, SK1

2 If there is no message in a message list, the list will be displayed in gray and you cannot select it.

Reading a message (M21)

☛ To display the Message view screen of a new message, SK1 or 2 ➔ 1 ➔ Highlight the new message ➔
☛ To display the MMS message,
☛ The new (unread) messages are displayed in bold. If the message cannot be displayed in one page, use ▲ and ▼ to scroll through the

message.The following icons will be displayed.

4Sent The sent messages are stored here.

5 Alert inbox The received alert messages are stored here.

2 You can also display the received alert messages by pressing 3 4 1 from the standby screen.

6CB The received broadcast messages are saved. See “Cell broadcast (M26)” on page 39 for details.

7, 8 Folder1/Folder2 The messages moved by Move msg (see “Message list Options menu” on page 32) are stored here.

Icon type Icons Descriptions Icon type Icons Descriptions
Message type

icons

MMS message with no attachment Read / Unread

status icons

New / Unread message(s)
MMS message with attachment Read message(s)
MMS message on the server Filtering

status icons

SMS messages filtered by status

(incomplete)
MMS delivery report SMS messages filtered by location (SIM)
SMS message SMS messages filtered by location (the

phone memory)
Incomplete SMS message Filtered SMS messages
Email message with no attachment Filtered MMS messages
Email message with attachment Filtered Email messages

No. Message screen menu

Options menus

Message Options menu

☛

SK1 or 2 ➔

No. Message Options menu

1SMS

settings

1 SMS centre Edits the SMS centre number (this number is saved in the SIM card).

2 Auto display Turns on/off the automatic display function that displays the received SMS messages

automatically.

3 Receipt request Selects whether to request a receipt of the sent SMS messages.

4 Max linked

msgs

Sets the maximum number of linked SMS messages. This function divides an SMS with the
message text exceeding the maximum number of characters allowed into multiple messages.

5 Validity period Selects the period of time an SMS message is stored at the SMS centre, while trying to deliver

the message.

2 MMS

settings

☛ To display the Msg settings screen, 1.

1 Delivery report Sets the status of delivery.

1 Receipt

request

Sets to request a receipt of the sent MMS message.

2 Auto send Sets to automatically send out a receipt for the received MMS message.

2 Auto receive Selects whether to receive the MMS messages manually or automatically.

3 Validity period Selects the period of time an MMS message is stored at the server, while trying to deliver the

message.

☛ To display the MMS profiles screen, 2.

– Connection

profile

Sets the Internet connection for sending or receiving MMS messages. See “Setting the
Connection profiles” on page 41.

3Email

settings
(Continued)

1,2 Account1/

Account2
(Continued)

2POP3 Sets POP3 server to receive the Email messages.

1 POP3 server Sets POP3 server address to receive Email messages.

2 POP3 port

override

Sets the POP3 port number.

3 Leave on

server

Selects whether to leave the downloaded Email
message on the server or not.

4 Login Sets the POP3 user ID and password to login to the

account.

3SMTP Sets the SMTP server to send the Email messages.

1 SMTP server Sets the SMTP server address to send Email

messages.

2SMTP port

override

Sets the SMTP port number.

3 Authentication Sets the authentication to on or off.

4 Login Sets the SMTP user ID and password to login to the

account.

2 You can also set them the same as those of

POP3.

3 Default account Sets the default accounts for sending and checking the Email messages.

4 Send option Selects whether to send an Email message immediately or later.

5 Received

message size

Sets the maximum size to download an Email message.

6 Connection

Sets the Internet connection for sending or receiving Email messages. See “Setting the

No. Message Options menu

, The receipt request, linking of SMS messages and delivery report facilities are network dependant.

2 Depending on the selected folder, some options may be displayed in gray and not be available.

Message list Options menu

☛

Display the message list in the Inbox, Drafts, Outbox, Sent, Alert inbox, CB, Folder1 or Folder2 ➔

6 Rename

folder

Renames Folder1 and Folder2.

7View all Displays all the messages in all folders on the same list.

8 Msg filter Sets the type(s) of messages to be displayed by selecting the desired filter option.

No. Message list Options menu

1Reply Replies to the sender of the highlighted message.
2 Reply all Replies to the sender and all other recipients of the highlighted message.
3 Delete Deletes the highlighted message.
4 Delete all Deletes all the messages in the current folder.
5 Forward Forwards the message text of the highlighted message.
6 Msgs/page Selects either to display 3 or 7 messages in one screen.
7 Move msg Moves the highlighted message to Inbox or Folder1/2, or copies to SIM/Phone.
8Sort msg By: Sorts the messages by date, name, read/unread status or size.

Order: Sorts the messages in ascending or descending order.
9 Search Searches messages alphabetically.
0 View details Displays the detailed information on the highlighted message.
– Add desktop icon Creates a desktop icon of the sender or recipient of the highlighted message (Inbox, Sent, Folder1/Folder2, and

Drafts only).

–Edit Edits the highlighted message (Drafts and Outbox only).

No. Message Options menu

Message view Options menu

☛

Display the message list in the Inbox, Drafts, Outbox, Sent, Alert inbox, CB, Folder1 or Folder2 ➔ Highlight a message ➔ ➔

2 Depending on the conditions, some options may be displayed in gray and not be available.
2 The reply facility uses the phone number of the person who sent the message.
2 The Save object Options menu will be displayed only if an object is highlighted.

Option mode Options menu

☛

Display the message list in the Inbox, Drafts, Outbox, Sent, Alert inbox, CB, Folder1 or Folder2 ➔ Highlight a message ➔ ➔ 0 / /
to highlight a phone number, Email address, URL or attached file in the message ➔

The columns show the menu numbers for P: Phone number highlighted, E: Email address highlighted, U: URL highlighted and A: Attachment
highlighted.

No. Message view Options menu

1Reply Replies to the sender of the highlighted message.

2 Reply all Replies to the sender and all other recipients of the highlighted message.

3 Delete Deletes the highlighted message.

4View details Displays detailed information on the highlighted message.

5 Forward Forwards the message text of the highlighted message.

6 Save object Saves the highlighted object to a folder in My data.

7 Attachments Displays the list of attached files.

8Move msg Moves the highlighted message to Inbox or Folder1/2, or copies to SIM/Phone.

9 Highlight mode Activates the Highlight mode (see “Highlight mode” on page 38 for details).

0 Option mode Activates the Option mode to highlight the phone number, Email address, URL or attached file.

Add desktop icon Creates a desktop icon of the sender or recipient of the highlighted message.

▼

▼

Creating a message

☛SK1 twice/press and hold SK1/ 2 and SK1
☛1 to create a new SMS, 2 to create a new MMS, or 3 to create a new Email
☛To address the message, highlight the To field ➔ ➔ Input the required phone

number or Email address ➔

2To scroll the phone numbers in the To field, or

☛To key in the message, highlight the Message field ➔ ➔ Key in the message

➔

2Pressing while keying in the To/Message field displays the Message edit

Options menu screen.

☛SK1 to send the message

2When you are in the ABC (normal text) mode, any word entered that is not in the

T9

®

dictionary will be added automatically.

2When you are keying in your message, SK1 to change the text entry mode.
2If you display another screen or receive a call while you are editing a message

more than 1 character, the message will be saved automatically in Drafts.

Message composer Options menu

To/Subject field Options menu

4 3 – – Add desktop icon Creates a desktop icon of the highlighted phone number/Email address.

– – – 1 Attachments Displays the list of attached files.

5 4 3 2 View mode Deactivates the Option mode.

P E U A Option mode Options menu

Help area

This area contains the
information on the message.
S indicates the size of the
message equivalent to the
number of SMS messages, and
R indicates the remaining
number of characters
available.

(green)

Indicates that an upper case letter will be input next.

(red)

Indicates the capital lock.

(no arrow)

Indicates that a lower case letter will be input next.

▼

▼

– 1 1Edit Edits the subject of a message.

2 2 2 Preview msg Displays the message preview screen.

3 3 3 Delete Deletes the highlighted recipient phone number/Email address or subject.

4 4 4 Delete all Deletes all the recipients phone numbers/Email addresses.

5 5 5Save Saves the message in Drafts folder.

6 6 – Phonebook Displays the phonebook list to insert a recipient phone number/Email address (To field only).

7 7 – Resend list Inserts a phone number/Email address from the resend list (To field only).

2 You can delete the highlighted phone number from the resend list or the entire resend list by

pressing 1 or 2 respectively.

8 8 – Insert Inserts a new recipient phone number/Email address.

9 9 – Address list Displays the recipient(s) of the message (To field only).

– – 6Add item Adds picture, video, sound, or text to the Email message.

– – 7 Attachments Displays the list of attachments. (See “Email Attachments list Options menu” on page 37 for details).
0 0 8 Msg options 2 This option is available only when creating an MMS or Email message.

When creating an MMS message:

1Priority Selects the message priority.

2 Delivery date Sets the delivery date.

When creating an Email message:

1 Send option Selects whether to send an Email message immediately or later.

2 Send account Chooses which account to send the message.

3Priority Selects the message priority.

To S E To/Subject field Options menu

2 The columns show the menu numbers for:

• S: The Message field highlighted when creating a new SMS message.

• M: The Slide field highlighted when creating a new MMS message.

• E: The Message or Attachment field highlighted when creating a new Email message.

S M E Message/Slide/Attachment field Options menu

1 1 1Edit Edits the message.

2 2 2Preview msgDisplays the message preview screen.

2 When previewing an MMS message, it displays the created slides in order from the beginning at the

preset playback time for each.

3 3 3Delete Deletes the highlighted slide or message.

4 4 4 Delete all Deletes all the slides or attachments.

5 5 5 Save Saves the message in Drafts folder.

6 – – Phonebook Displays the phonebook list to insert a recipient phone number/Email address.

7 – – Resend list Inserts a phone number/Email address from the resend list.

– 6 – Insert object Inserts Text, Sound, Still image, Animation, Emoticon or Video into the slide.

– 7 – Copy Copies the highlighted slide.

☛ Highlight the slide you want to copy ➔ 7 ➔ Highlight the place you want to copy the slide to

➔SK1

– 8 –Move Moves the highlighted slide.

☛ Highlight the slide you want to move ➔ 8 ➔ Highlight the place you want to move the slide

to ➔SK1

– 9 –New slide Inserts a new slide just before the currently highlighted slide.

– 0 –Duration Sets the length of time a slide is displayed in seconds when previewing the MMS message.

– – 6 Add item Adds picture, video, sound, or text to the Email message.

Email Attachments list Options menu

☛ SK1 twice/press and hold SK1/ 2 and SK1 ➔ 3 ➔ Highlight the Attachments/Message field and 7 or highlight the attachment field

and

➔

2 Depending on the conditions, some options may be displayed in gray and not be available.

Message composer icons

The following icons will be displayed at the bottom of the Message composer screen.

No. Email Attachments list Options menu

1Add item Adds picture, video, sound, or text to the Email message.

2 Save item Saves an attachment of the Email message in a folder.

3 Delete item Deletes an attachment from the Email message.

4 Delete all Deletes all attachments of the Email message.

5 Rename item Renames an attachment of the Email message.

6 Copy item Copies the highlighted attachment.

7Copy all Copies all the highlighted attachments.

8Move Moves the highlighted attachment or all the attachment to another field or folder.

9 Create folder Creates a new folder.

0 Storage detail Displays the storage information.

View detail Displays detailed information on the highlighted attachment.

# Options See “Options” on page 64 in “File selector Options menu” for details.

Icons Descriptions Icons Descriptions

The plain MMS message MMS message with text(s) and video(s)

Message edit Options menu

☛

SK1 twice/press and hold SK1/ 2 and SK1 ➔ 1, 2, or 3 ➔ Highlight To or Message field ➔ ➔

MMS message with video(s) Email message with text(s)

MMS message with text(s) and picture(s) Email message with no attachment(s)

MMS message with text(s) and sound(s)

Email message with attachment(s)

2 The number in the icon indicates the number of attachments.

No. Message edit Options menu

1 Text colour Selects the colour of text and background.
2 Text format Selects the font size (small, normal or large) and font style (bold, italics, underline or strikethrough).
3 Text alignment Sets the text alignment (left, centred or right).
4 Paste Pastes the text which has been copied onto the clipboard in the Highlight mode.

2 This function can be used only when text has been copied or cut in the Highlight mode.

5 Highlight mode Activates the Highlight mode at the cursor position.

2 You can also activate the Highlight mode by pressing and holding .
2 This function can only be used when text has been entered.
2 To toggle the Highlight mode on/off, SK1 and to go back to the normal mode, CLR

☛ To display the following Highlight mode Options menu, .

1 Text colour Selects the colour of text and background.

2 Text format Selects the font size (small, normal or large) and font style (bold, italics, underline or

strikethrough).

3 Copy Copies the highlighted part of text onto the clipboard.

4Cut Cuts the highlighted part of text.

Icons Descriptions Icons Descriptions

2 Depending on the conditions, some options may be displayed in gray and not be available.

Cell broadcast (M26)

Cell broadcast (CB) messages (e.g. weather reports, news) are sent by the network to all phones in a certain area.

☛ 2 6

2 The Cell broadcast message display on the standby screen is erased by pressing CLR.

, Broadcast messages service is network dependent. Please contact your service provider for details.

8 Edit settings Sets the Write mode (Insert or Overwrite) and Clear mode (Backspace or Delete).

No. Message edit Options menu

Web browser (M3)

To access WAP service, you would need to:

1 Apply for WAP service before accessing WAP. You can choose General Packet Radio Service (GPRS) or

Circuit Switched Data (CSD) as the data bearer for WAP access. The connection speed of GPRS is faster than
CSD. For more details or subscription of WAP service, please contact your network service provider.

2 Set up WAP service settings in your phone.

What can I download

Your phone supports the downloading of the following different types of content:

• Sound files (including ringer melodies, video sound, etc.)

• MP3

• Pictures

• Animation

• Video

• Java™ applications

/ For the handling of the downloaded data, see “My data (M6)” on page 59.
/ For details on downloading Java™ applications, see “Java™ (M7)” on page 65.

2 If you have not enough memory left on your phone for the downloaded file, a message will be output and you cannot download the file. Make sure

you have enough memory space before downloading any file.

Web settings

To set up your phone to access WAP information on the Internet, use the following procedures.

Setting your connection profile and homepage

Setting the Connection profiles

To alter or enter information into a connection (profile), use the following procedure.

☛ 3 5 1 ➔ Highlight Connection profiles field ➔ ➔ Highlight a connection name ➔ to display the Profile options menu.

2 You can also display the Profile options menu by 1 9 and

Adding a new profile

☛ To add a new profile, 3 5 1 ➔ Highlight Connection profiles field ➔ ➔ SK1 or 1

2 You can also add s new profile by 1 9 and SK1

☛ Key in the proxy title ➔

No. Profile options menu

1 Add new Creates a new profile.

2Copy Copies the current profile to use it as a template to create a new profile.

3Edit Edits the current profile.

4 Delete Deletes the current profile.

No. Profiles settings menu

1 Load preset Chooses a profile to load the settings from.

2 Profile title Sets profile’s name.

3 IP address Sets IP address. If you do not have an IP address, please contact your network provider.

4Bearer type GPRS: Always connects by GPRS.

CSD: Always connects by CSD.

5 GPRS settings AP name: Edits the address of the external data network you want to connect to, either an IP address or a text

string.

User name: Edits your user ID to enable you to log on to the external data network.

☛ When you have finished entering or editing the connection information, SK2. The connection list will be displayed.

2 If you select the read-only proxy, Edit function is disabled.
2 For more details of profile settings, contact your network service provider.

Setting the CSD linger time

The linger time facility will disconnect a connection that has not been used for a preset amount of time. To set this time delay, use the following procedure.

☛ 3 5 2 ➔ Enter the time delay required ➔ SK1

Web font

You can select the font to be displayed on your phone's screen from Large, Normal and Small.

☛ 3 5 3 ➔ Press the appropriate key for the required font.

Clear cache

If you start a WAP session using the last page visited, the information will be restored from the phone memory. If, however this page has been updated
since your last visit, the updated page will not be displayed. To avoid this possibility, clear the memory by the following procedure:

☛ 3 5 4 ➔ SK1

Logging on to WAP site

7 DNS address Dynamic: Sets to use the dynamic DNS server address.

Static: Sets the static DNS server address.

8 Port number HTTP: Sets the HTTP port number.

HTTPS: Sets the HTTPS port number.

9 Authentication Selects the authentication type from Normal or Secure.

0 Usage Displays the name of the application currently used.

No. Profiles settings menu (Continued)

Connect to the Home page of the default connection

☛

3 1 2 (for details, see “Setting your connection profile and homepage” on page 40)

Connect to the last web page visited

☛

3 1 3

2 When you access the Internet with your phone for the first time or after you cleared the memory, the homepage set for Web/MMS profile will be the

page to be accessed.

Other features

Bookmark

☛

3 2

☛ To display the list of bookmarked pages, 1
☛ To reset the bookmarked pages, 2

Snapshot

The Snapshot function allows you to store up to 10 web pages and view them offline.

☛ 3 3
☛ To display the list of stored snapshots, 1
☛ To delete all the stored snapshots, 2

2 The above operation is available only when one or more Snapshot data has been stored.
2 To take a snapshot, you need to access the Snapshot screen while browsing a WAP site.
2 Stored snapshot data can only be used for the snapshot function.

Alert message

☛

3 4

☛ To display the list of received Alert messages, 1

☛ To delete all those messages, 2

2 You can also display the received Alert messages by pressing 2 / SK1 ➔ 5.

GPRS dial up

With GPRS dial up service, you can access the Internet or read Emails from your PC through your phone. Use your phone as a modem to connect to a
compatible PC through a USB cable (option), Bluetooth or the IR port to enable GPRS Internet dial up service.

For more detailed procedures, please visit our company homepage.

/ See also “Bluetooth (M891)” on page 76 and “IR modem (M8922)” on page 80.

2 Before using this service, you would be required to subscribe to a GPRS service and buy a USB cable and CD-ROM.

Phonebook (M4)

Phonebook types

Your phone can have up to 7 directories stored on your SIM card and in your phone memory:

• Complete (a list of all the numbers stored in the ADN and FDN)

• Personal directories (ADN) in the SIM card

• Personal directories (ADN) in the phone memory

• Service dialling numbers (SDN)

• Fixed dialling numbers (FDN)

• Own number

• Voice mail number

2 When viewing any of the directories described, you can switch to the other directories (if your SIM card supports them) by pressing .

2 The maximum number of phone numbers that can be stored on a SIM card is the total of the ADN, FDN and SDN directories.

2 When you activate the phonebook, the directory which you were referring to the last time will open.

Personal directory (ADN)

These numbers are known as abbreviated dialling numbers (ADN). There are two types of ADN, one is the phonebook stored in the phone memory
(the phonebook (Phone)) and the other is the phonebook stored on the SIM card (the phonebook (SIM)).

Phonebook (SIM)

• Up to 255 personal data can be stored in the SIM card.

• Each personal data contains a phone number, a name and a location number.

2 The number of phone numbers that can be stored on a SIM card depends on the SIM card capability.

Phonebook (Phone)

Up to 500 personal data can be stored in your phone memory. Each personal data is given a location number (1 to 500), and it can be allocated to a

Fixed dialling numbers (FDN)

Fixed dialling numbers are a means of limiting which numbers can be called from your phone. With the FDN feature switched on (see page 26), you can
call with your phone the numbers you have stored in this phonebook and the emergency number only.

, Although FDN is supported by your phone, it must be present on your SIM card - check with your service provider.

Service dialling numbers (SDN)

The numbers stored in the SDN directory are pre-installed by your service provider. They will call numbers and services as agreed with your supplier
(e.g. customer enquiries, billing information, sportslines, weatherlines, etc.) and cannot be edited by you.

, Although SDN is supported by your phone, it must be present on your SIM card - check with your service provider.

Accessing your phonebook (M4)

You can store personal information in the phonebook of your phone or your SIM card.

Displaying a personal data (M41)

☛

4 1 and the appropriate key for the desired directory or until the required directory is displayed ➔ Highlight the required personal data

➔

Phonebook list screen Personal data screen

SK2

Location number

Location number

Phonebook list Options menu

☛ 4 1 and the appropriate key for the desired directory or until the required directory is displayed ➔ Highlight the required personal data

➔

No. Phonebook list Options menu

1 Add new Adds a new personal data to Phone/SIM/FDN.
2Edit Displays the data edit screen to edit the currently highlighted personal data.

2 When editing the data in FDN, you will be prompted to enter PIN2 code.

3Copy Copies personal data to another phonebook (see “Copying and moving personal data” on page 51 for details).

1 Current copy Copies the currently highlighted personal data.

2 Package copy Copies the selected data in the list.
4Move Moves the currently highlighted personal data to SIM, Phone, FDN, Own number or Voice mail number.
5 Delete Deletes personal data.

1 Delete current Deletes the currently highlighted personal data.

2 Delete all Deletes all the data in the list.

6 Groups Editing the group information

☛ Highlight the group you wish to edit ➔ SK1 and highlight the required field
☛ To rename the group name, select Group name field ➔ Key in the name of the group ➔
☛ To set information on the selected group, select Info field ➔ Key in the info ➔
☛ To select the LED colour, select LED field ➔ 1 ➔ Highlight the desired colour ➔
☛ To select the CLI picture/video, select Picture/Video field ➔ 1 for Picture or 2 for Video ➔ Highlight the desired

picture or video ➔

☛ To select the ringer, select Ringer field ➔ 1 for Sound, 2 for Video or 3 for MP3 ➔ Highlight the desired sound,

video or MP3 ➔

☛ SK1 to set the change

2 If the personal settings for the LED colour, CLI picture/video, or the ringer are also set, they have priority over

those of the Group settings.

Group member list screen Options menu

☛ Highlight the group you wish to edit ➔ to display the list of group members ➔ Highlight the member ➔

1Call Calls the highlighted member.
2 Create message Creates a new message to the highlighted member.
3 Add new Creates a new phonebook entry to join the group.
4 Add to group Adds a phonebook entry to the group.
5 Remove from group Removes the highlighted member from the group.
6 Remove and delete Removes the highlighted member from the group and delete the phonebook entry at the

same time.

7 Add desktop icon Creates a desktop icon of the phone number/Email address of the highlighted member.

7Sort Sorts the personal data in the order of alphabets or location number.

2 Sorting may take time depending on the number of personal data entries, the number of characters contained in

No. Phonebook list Options menu

2 Depending on the conditions, some options may be displayed in gray and not be available.

Making a call or creating a message from the phonebook list

☛

Highlight a desired personal data to display the stored numbers or Email addresses in the help area ➔ Use and to display the other stored
phone numbers or Email addresses, if any, in the help area.

☛ to make a phone call to the displayed phone number, or SK1 to send a new message to the phone number or Email address

Adding a new personal data

☛

4 1 and the appropriate key for the desired directory, or until the required directory is displayed ➔ SK2 ➔ Select the directory to which you wish to

store the personal data ➔ Enter the name and other necessary information ➔ SK1 (see “Editing an existing personal data” on page 49).

2 You can also input phone numbers on the standby screen and to add a new personal data.
2 It is best to store numbers using the international number format.

Editing an existing personal data

☛ 4 1 and the appropriate key for the desired directory or until the required directory is displayed ➔ Highlight the required personal data

➔ 2

8 Location Searches for the personal data by the location number.

☛ Key in the desired location number ➔ SK1 to display the Phonebook list screen with the selected personal data

highlighted.

9Show Displays phonebook information.

1 Summary Displays the summary of phonebook contents.

2 Voice tag list Displays the phonebook entry names with the voice recognition tags recorded.
0IR send Sends the currently highlighted personal data to another device through the IR port.

/ See also: “IR send” on page 79.

Add desktop
icon

Creates a desktop icon of the highlighted personal data.

No. Phonebook list Options menu

▼

▼

Allocating a group

☛ Highlight the Group field ➔ ➔ Highlight the group you wish to add the current personal data to ➔

Voice recall functions

Adding a Voice recall recording

☛ Highlight the Voice tag field ➔ ➔ 1
☛ Say the name you wish to record as a voice tag ➔ Say the name again for confirmation according to the displayed message.

Playing a Voice recall recording

☛ Highlight the Voice tag field ➔ ➔ 2

Deleting a Voice recall recording

☛ Highlight the Voice tag field ➔ ➔ 3

2 Up to 10 voice tags can be stored.
2 You can check the number of stored voice tag and list of those tags (see “Summary” and “Voice tag list” on page 49).

Allocating a LED colour

☛ Highlight the LED colour field ➔ ➔ 1 ➔ Highlight the desired colour ➔

2 The personal setting for the LED colour has priority over the Group setting and phone setting for the LED colour.

Allocating a picture or video as a CLI

You can set a picture or video to be displayed on the screen as a Calling Line Identification (CLI) for an incoming call.

☛ Highlight the Picture/Video field ➔ ➔ 1 to display the picture list screen or 2 to display the video list screen
☛ Highlight the desired picture/video ➔ SK1 to preview the picture/video or to select the highlighted picture/video

2 A ✔ is displayed on the icon for which the item is currently selected.
2 If an MP3 file is set as a ringer in Phone mode and a CLI video is also set, the default picture, instead of the CLI video, will be displayed with the MP3 file.

2 See also: “Ringer” on page 23 and “Pictures (M63)” on page 60.

Allocating sound/video/MP3 as a ringer

You can set a sound, video or MP3 as a ringer for an incoming call. When a video is set, a movie is displayed on the screen with the sound.

Saving the edited personal data

☛ After editing the required field, SK1 to save the edited data and return to the previous screen.

Copying and moving personal data

☛

4 1 and the appropriate key for the desired directory or until the required directory is displayed ➔ Highlight the required personal data/

list of data ➔ 3 to copy or 4 to move

☛ For copying, 1 to copy the highlighted personal data entry or 2 to copy the selected personal data entries in the current list
☛ Press the appropriate key for the desired destination (SIM, Phone, FDN, Own number or Voice mail number)

2 If you copy or move from phonebook (Phone), the Origin number screen will be displayed to choose which phone number to copy or move.
2 When copying the selected personal data entries (Package copy) from phonebook (Phone), you can copy only the first or all the numbers in each

entry.

☛ Key in the desired location number ➔

2 If you copy or move to phonebook (Phone), the Number type screen will be displayed to choose the phone number type.

Personal data Options menu

☛ 4 1 and the appropriate key for the desired directory or until the required directory is displayed
☛ Highlight the required data ➔ ➔ Highlight the required field ➔

No. Personal data Options menu

1Call Calls the highlighted phone number.

2 Create message Creates a new message to the highlighted phone number or Email address.

3 IR send Sends the selected personal data to another device through the IR port.

4Edit Edits the selected personal data.

5Copy Copies the selected phone number(s)/Email address(es).

☛ Press the appropriate key for the desired destination (SIM, Phone, FDN, Own number or Voice mail

number) ➔ Key in the desired location number ➔

Voice mail (M417)

Voice mail function enables you to forward received calls to the Voice mail centre, and the caller can leave voice messages in your voice mail mailbox.
You may be notified by an icon on the standby screen if the caller leaves a voice message.

, The voice mail service is network dependent. Contact your service provider for details on your voice mail number.

Setting the Voice mail number

2 This function is available when the Voice mail number has not been set.

☛ 4 1 7 ➔ Highlight the required line ➔ twice ➔ ➔ key in the voice mail number ➔ ➔ SK1 to save the change.

Forwarding a call to the Voice mail centre

☛

Set the voice mail centre number (see “Setting the Voice mail number” for details) ➔ Set up Call diversion (see “Call diversion (M161)” on page 13
for details). When you receive a call set to be diverted, the call will be diverted to the voice mail centre.

Retrieving a Voice mail

2 This function is available when the Voice mail number has been set.

☛ 4 1 7 ➔ Highlight the required line ➔

2 You can also retrieve a voice mail by pressing and holding 1 from the standby screen.
2 To set up the line to call the voice mail centre, see “ALS setup” on page 21 for details.

Camera (M5)

Camera function enables you to take pictures or record videos and save them as Joint Photographic Expert Group (JPEG) files and 3rd Generation
Partnership Project (3GPP) files respectively. You can enjoy the picture and video files in many ways: send them attached to an MMS or Email, set a
picture file as the wallpaper for your phone, etc.

Notes on using the camera

Handling the Camera

, The camera of your phone is manufactured using high-precision technology. However, there may be dots or lines on the screen that

appear darker or brighter than the others. Note also that when you are shooting or recording in dimly-lit places, the amount of noise
(such as red and blue dots or horizontal lines) may increase noticeably.

, Be careful not to apply force to the lens when closing your phone. This could damage the lens.

2 Fingerprints or grease on the lens can result in focusing problems or dark images. Wipe the lens clean with a soft cloth before use.
2 The image quality may be degraded after your phone has been left for a long period in a warm place.
2 Exposing the camera to direct sunlight for a long period could discolour the camera’s internal colour filter and cause discoloured images.
2 Camera mode is automatically cancelled if none of the phone’s keys are pressed for 3 minutes or longer.

Precautions when taking pictures/recording videos

2

You cannot switch the camera’s shutter sound off. The shutter makes a clicking sound when you take a picture or start/end a video recording,
even when the phone is in Meeting mode.

2 Avoid camera shake. Moving the phone when you take a picture will result in a blurred image. Hold the camera firmly to keep it still when you take

a picture, or use the auto timer to take the shot.

2 As there is a slight delay from the time you press or Side up until the picture is actually taken, do not move the camera until you hear the shutter sound.
2 If taking a picture with not enough light, try to hold the phone still as much as possible, and for a longer period of time after the shutter sound: the

shutter speed may be slower in a darker environment.

2 Note that if you attempt to shoot directly into a strong light source, such as the sun, another bright light or the high reflecting target with strong

light, the image may contain washed-out white highlights or be disrupted.

Taking a picture (M51)

☛ To activate the camera function, press and hold Side up or 5 1

2 When you highlight Camera on the Camera screen, pressing SK1 creates a desktop icon of the camera function on the standby screen.

☛ Look into the camera view finder screen and adjust the camera position to place the target on the screen.

2 You can switch the camera view finder screen between the main-LCD and the 2nd-LCD by pressing .
2 You can take a picture while the phone is closed.

☛ Hold the phone still ➔ To use the shutter, or Side up ➔ Check the picture ➔ If successfully taken, ➔ Saved as a JPEG file in a folder in

Pictures

2 After taking a picture, SK1 to send the taken picture attached to a message, and SK2 to discard the picture.
2 The default file name for the picture saved in the folder is the date, month, year and sequence number. When you take pictures in burst mode,

the saved files will be named by the default file names plus a consecutive two-digit number at the end.

2 If a call comes in while you are checking or saving a photographed image, image storage is cancelled. When this occurs, the next time you select

camera function a message appears to say that you have an image that was not stored, allowing you to check and store the image.

2 Before taking a picture, you can switch to the video camera function by pressing SK2. This use of SK2, however, is invalid if the self-timer function

is activated.

Operations when taking a picture

☛

To turn the light on or off, SK1 or Side down

2 Take care not to hold the light too close to your or other people’s eyes when the light is lit.

☛ To zoom in and out, ▲ or ▼

2 You can also select 1x, 2x, 3x, 4x or 5x magnification from the Zoom setting on the Camera Options menu.

☛ To turn on/off the camera view finder on the full screen, #.

2 Depending on the photo size, there may be parts not seen on the full screen view finder display in the saved picture.

☛ To control the brightness level of the picture, or

Camera Options menu (before taking a picture)

▼

▼

4Photo size Sets the picture size to Sub-QCIF (128x96), QCIF (176x144), Main-LCD (176x220), CIF (352x288), VGA

(640x480) or SXGA (1280x1024).

2 You cannot use the Zoom function for VGA and SXGA, and you can select 1x to 2x magnification for

Main-LCD and CIF, 1x to 4x magnification for QCIF and 1x to 5x magnification for Sub-QCIF.

2 You can use the Frame and Burst mode functions for Sub-QCIF, QCIF and Main-LCD.
2 You cannot use the Full screen function for Sub-QCIF and QCIF.

2 If you select Main-LCD, CIF, VGA or SXGA, the picture on the camera view finder screen will be displayed

as a smaller picture than the actual size. Also on the camera view finder screen, the picture size before
shooting differs from the size after shooting.

5 Image quality Sets the image quality to Super fine, Fine, Normal, Economy or Super economy.

6Frame Selects whether to use a frame when taking pictures, and sets the desired frame with which a picture will be

taken.

7 Self timer/Self timer

cancel

Activates or deactivates the self-timer function.

8 Sound settings Selects the Shutter sound and Self timer sound.

9Pictures Opens Pictures in My data.

0 Other settings Add desktop icon: Creates a desktop icon of the camera function on the standby screen.

Automatic save: Selects whether to save taken pictures automatically or not.
Save in: Selects the folder (preset or created) where the taken picture will be saved.
Light: Turns the light on or off.
Brightness: Changes the brightness level of the picture between -2 and +2.
Zoom: Changes the zoom magnification from 1x, 2x, 3x, 4x or 5x.
Thumbnail view: Selects whether to display the pictures taken in the Burst mode as thumbnails or

slides.

Video recorder: Activates the video function.
Flicker control: Selects 50Hz, 60Hz or Auto to prevent flickers when taking a picture under a

No. Camera Options menu (before taking a picture) (Continued)

Camera Options menu (after taking a picture)

2

Depending on the conditions, some options may be displayed in gray and not be available.

Recording a video (M52)

Recording a video

, To record a video, keep your phone open at all time. Unlike taking a picture, you cannot record a video while the phone is closed.

☛ Press and hold Side up then SK2, or 5 2 ➔ Look into the view finder screen and adjust the camera position.

2 When you highlight Video recorder on the Camera screen, pressing SK1 creates a desktop icon of the video function on the standby screen.

No. Camera Options menu (after taking a picture)

1 Save current Saves the currently displayed picture in the folder selected as Save in setting.

2 In Burst mode, only the highlighted picture is saved.

2 Save all Saves all pictures taken in Burst mode.

3 Create message Creates a new message with the file attached.

4 Set as wallpaper Sets the picture to be the main-LCD or 2nd-LCD wallpaper.

5 Display as normal

image/Display as mirror
image

Selects whether to display the taken picture as a normal or mirror image on the main-LCD preview screen
when you select the 2nd-LCD as a camera view finder in Single mode.

6 Save as mirror image Saves the picture as a mirror image when you select the 2nd-LCD as a camera view finder in Single

mode.

7 Thumbnail view Selects whether to display the pictures taken in the Burst mode as thumbnails or slides.

8 Automatic save Selects whether to save taken pictures automatically or not.

9 Save in Selects the folder (preset or created) where the taken picture will be saved.

0Pictures Opens Pictures in My data.

2 While replaying, you can fast forward by pressing or rewind by pressing . / again to cancel fast forwarding/rewinding and continue to

replay.

2 You can discard the recorded video by pressing or CLR.

☛ To save the recorded video, . The recorded video is saved as a 3GPP file in the Videos - My movies folder in My data (see page 59).

2 Pressing # before/while playing a video file will enlarge the replay screen size, and pressing # will return the screen size to normal for Sub-QCIF

only.

2 The default file name for the recorded video saved in the folder is the date, month, year and sequence number.

/ For the operations while replaying the video, see “Videos (M61)” on page 59.
/ For the operations while recording a video, see “Operations when taking a picture” on page 54.

2 If a call comes in while you are checking or saving a video, video storage is cancelled. If this occurs, the next time you select camera function a

message appears to say that you have a video that was not stored, allowing you to check and store the video.

2 Before recording a video, you can switch to the camera function by pressing SK2. This use of SK2, however, is invalid if the self-timer function is

activated.

Operations when recording a video

☛

To turn the light on or off, SK1 or Side down

2 Take care not to hold the light too close to your or other people’s eyes when the light is lit.

☛ To zoom in and out, ▲ or ▼
☛ To control the brightness level of the picture, or

Video recorder Options menu (before recording a video)

No. Video recorder Options menu (before recording a video)

1 Shoot environment Changes the camera settings to suit the conditions. Select from Standard, Person, Room or Darkness.

2Effect Applies special effect to the video. Select from Off, Sepia, Monochrome or Negative film.

3 Screen size Sets the video screen size to Sub-QCIF (128x96) or QCIF (176x144).

4 Video file size Sets the video file size to Mail size or Normal size.

▼▼▼

▼

▼

▼

2 Depending on the conditions, some options may be displayed in gray and not be available.

Video recorder Options menu (after recording a video)

9 Other settings Add desktop icon: Creates a desktop icon of the video function on the standby screen.

Save in: Selects the folder (preset or created) where the recorded video will be saved.
Light: Turns the light on or off.
Brightness: Changes the brightness level of the video between -2 and +2.
Zoom: Changes the zoom magnification from 1x to 5x for Sub-QCIF and from 1x to 4x for

QCIF.

Camera: Activates the camera function.
Flicker control: Selects 50Hz, 60Hz or Auto to prevent flickers when taking a picture under a

fluorescent light.

0 Switch finder Selects whether to display the viewfinder on the Main-LCD or the 2nd-LCD.

No. Video recorder Options menu (after recording a video)

1 Save Saves the currently displayed video.

2 Create message Creates a new message with the file attached.

3 Set as ring tone Sets the video as the ringtone.

4 Set as wallpaper Sets the video to be the main-LCD wallpaper.

5 Full screen Selects whether to enlarge the replay screen size.

2 You cannot use the Full screen function for QCIF.

6View detail Displays detailed information on the selected video.

7 Save in Selects the folder (preset or created) where the recorded video will be saved.

8Videos Opens Videos in My data.

No. Video recorder Options menu (before recording a video)

My data (M6)

Using My data, you can playback sound and MP3 files, or display pictures and videos downloaded from the Internet or captured with the camera function
of your phone.

Videos (M61)

In the following section, how to playback video files (videos) stored in your phone is described. You can either record videos using your phone, download
them from the Internet, receive them attached to messages. There are two pre-set folders: My Movies and Download.

Replaying the video files

☛

▼ 1 or 6 1 ➔ Highlight a folder ➔ ➔ Highlight a video file you wish to replay ➔ ➔ The video file will be replayed.

2 When the flat view function is activated, the list of folders is not displayed. The list of all the stored video files is displayed.
2 If you wish to move to another hierarchy folder, use and .
2 Pressing # on the video preview screen will enlarge the replay screen size, and pressing # again will return the screen size to normal for Sub-

QCIF only.

2 For the definitions of the icons displayed while replaying, see “LCD and displayed icons” on page viii.

Operations while replaying video

☛

To stop, SK2

☛ To pause, SK1 ➔ While pausing, SK1 again to restart and continue the replay.
☛ To fast forward/rewind, / ➔ / again to cancel fast forwarding/rewinding and continue the replay
☛ To enlarge the replay screen size, # for Sub-QCIF only
☛ To adjust the volume, Side keys
☛ To display the previous/next file, ▲ or ▼

2 You cannot fast forward, rewind or enlarge the screen for video files with only sound but no image.

▼

▼

▼▼▼

▼

Operations while playing sound

☛ To stop, SK2
☛ To adjust the volume, Side keys.
☛ To replay the previous/next file, ▲ or ▼

Pictures (M63)

The Pictures function allows you to display images and animations, which were obtained with the camera function of your phone, received as a file
attached to MMS messages, or downloaded from the Internet. The images can also be edited using this function. From the Pictures function you can
also attach images and animations to messages you compose. There are five pre-set folders: Photo, Download, Preset, Frame, and Stamp.

Displaying the Pictures view screen

☛

▼ 3 or 6 3 ➔ Highlight a folder ➔ ➔ Highlight an image file you wish to display ➔

☛ To display the previous/next image file, ▲ or ▼

2 When the flat view function is activated, the list of folders is not displayed. The list of all the stored image file is displayed.
2 If you wish to move to another hierarchy folder while the Thumbnail view is turned off, use and

Cutting the image

☛

Highlight or display the image file you wish to edit ➔ 1 3 ➔ Select the image size ➔ A frame indicating the cut area appears on the preview screen.

☛ Move the frame position ➔ ➔ SK1 if the image is favorable
2 When you select Free, a cross indicator appears on the preview screen. Move it to the point to start a frame and to confirm the position. Then,

expand the frame into the required size and to confirm.

Reducing the image size

☛

Highlight or display the image file you wish to edit ➔ 1 4 ➔ Select the image size ➔ SK1 if the image is favorable

Rotating the image

☛

Highlight or display the image file you wish to edit ➔ 1 5 ➔ SK1 to rotate the image 90 degrees clockwise.

▼

▼

Adding a frame to the image

☛

Highlight or display the image file you wish to edit ➔ 1 7 ➔ Highlight a frame ➔ to preview the resulting image ➔ Scroll through the
various frames by ▲ and ▼ ➔ to confirm.

Saving the edited image

☛

After any edition, SK1 or to save the edited image ➔ Select the Save Quality

2 SK1 to check the expected size of the image.

☛ Edit the name (if required) ➔

Printing an image using a printer

You can print an Exif format image file by connecting your phone to a PictBridge compatible printer using a USB cable (option).

2 There may be PictBridge compatible printers that cannot be connected to your phone.
2 Refer to the operation manual of the printer for details on the printing.
2 For some printers, an image file name including characters other than alphanumeric characters (e.g. accentuated characters) may cause an error

when printing.

☛ ▼ 3 or 6 3 ➔ Highlight a folder ➔ ➔ Highlight an image file you wish to print ➔ 2 4

2 “Print via USB” may be displayed in gray and unavailable, depending on the image file.

☛ Connect your phone and the printer with the USB cable ➔ Prepare the printer ready for printing, referring to its manual
☛ Check the print detail screen displayed

☛ To print as seen on the detail screen, SK1
☛ To edit the print detail and then print, on the print detail screen to display the Options menu ➔ Edit the detail using the Options menu

➔ SK1

2 The Options menu may change depending on the connected printer.

2 If any interruption or error occurs, or the printing is not completed normally, pull out the USB cable and start again from the first step.

No. Print via USB Options menu

1 Number of prints Sets the number of prints to output.

MP3 (M64)

In the following section, the procedures to display and play your MP3 files are described. There is one pre-set folder: Download.

Selecting and playing an MP3 file

☛

▼ 4 or 6 4 ➔ Highlight the MP3 file you want to play ➔

2 When the flat view function is activated, the list of folders is not displayed. The list of all the stored MP3 files is displayed.
2 To create your own playlist, see “MP3 player (M81)” on page 67.

Operations while playing an MP3 file

☛ To stop, SK2
☛ To adjust the volume, Side keys.
☛ To replay the previous/next file, ▲ or ▼

File selector Options menu

☛ Display the Videos/Sounds/Pictures/MP3 list screen ➔ Highlight a file ➔

No. File Selector Options menu

1 Edit item Rename item: Edits the file/folder name of the selected file/folder.

Set protection: Sets the protection settings of the selected folder or file on/off.
Cut: Cuts the selected picture into Sub-QCIF (128x96), QCIF (176x144), Main-LCD (176x220), 2nd-

LCD (128x128) or Free.

Reduce: Reduces the selected picture to fit within Sub-QCIF (128x96), QCIF (176x144), Main-LCD

(176x220) or 2nd-LCD (128x128).

Rotate: Rotates the selected picture.
Stamp tool: Adds a marker or text stamp on the selected picture.
Frame: Sets a frame to the selected picture.

2 You cannot use the Cut and Rotate functions for SXGA.

2Use item

(Sounds)

Set as ring tone: Sets the selected sound to be the ring tone.
Set as SMS tone: Sets the selected sound to be the SMS tone.
Set as MMS tone: Sets the selected sound to be the MMS tone.
IR send: Sends the selected sound through the IR port to other devices or a cellphone.

2Use item

(Pictures)

Set as wallpaper: Sets the selected image to be the main-LCD or 2nd-LCD wallpaper.
Add desktop icon: Creates a desktop icon for the selected image on the standby screen.
IR send: Sends the selected image through the IR port to other devices or a cellphone.
Print via USB: Prints the selected image file using a PictBridge printer via USB cable (option) (see

page 61).

2 Use item (MP3) Set as ring tone: Sets the selected MP3 to be the ring tone.

IR send: Sends the selected MP3 through the IR port to other devices or a cellphone.

3 Create message Creates a new message with the file attached.

2 This function is not available for the MP3 files.

4 Delete item Deletes the selected file and folder.

5 Delete all Deletes all the files in the current list.

6 Copy item Copies the selected file or folder to the selected folder.

7Copy all Copies all the files in the current list to the selected folder.

8Move Moves the selected file/folder or all the files in the current list to the selected folder.

9 Create folder Creates a new folder under the current folder.

0 Storage detail Displays the current storage information of your phone memory.

View detail Displays the details of the selected folder or file.

2 You can also display the details on the highlighted folder or file by pressing without displaying the Options

menu.

No. File Selector Options menu

2 Depending on the conditions, some options may be displayed in gray and not be available.
2 Depending on the size of the data, file selector operation may take a long time.
2 Neither protected data nor preset data and folders can be deleted or moved.

# Options Sorting order: Sorts the files by date, alphabetically.

Info column: Sets whether to display the column on the list screen, and the information to be shown

there.

None: No column showing
Size: Approximate size of the file
Type: File type

2 You can also change the information on the column by pressing # without displaying the

Options menu.

Thumbnail view: Displays the files as thumbnails (for Pictures only).
Flat view: Displays the list of all the stored files regardless of the folder hierarchy.
List display: Sets whether to display the user title or the file/folder name.

Title: Displays the user title.

File name: Displays the file/folder name.
Save options: Saves the current option settings.
Reset options: Resets the option settings.

No. File Selector Options menu

Java™ (M7)

You can download Java™ applications (games etc.) from WAP sites and run them on your phone.

Applications (M71)

How to run software

To run a software (Java™ application), perform the following.

☛ 7 ➔ 1➔ Highlight an application containing the software you want to run ➔ or

2 When you display the Java™ applications list screen for the first time after downloading a program(s), it may take a while for your phone to verify

the program(s). A message will be displayed during this process, and you may activate the program(s) after it is completed.

, After downloading the software, always make sure that you check the downloaded program is displayed in the Applications screen.
, Do not remove the battery while the software is running as data to that point may not be saved.

Applications Options Menu

☛

7 ➔ 1 ➔ Highlight an application containing the software you want to run ➔ SK1

Network setting (M72)

You can select the connection profile for the Java™ application software to connect to the network.

☛ 7 ➔ 2 ➔To display the Web profiles screen, 1, or to display the Connection profile screen, 2 (see “Setting the Connection profiles” on

No. Applications Options menu

1View info Displays the information of the selected application.
2 Delete current Deletes the currently highlighted Java™ application.
3 Delete all Deletes all the applications.
4 Security setting Displays the security setting of the highlighted application.

▼

Selecting the resident Java™ application (M7311)

☛

7 ➔ To display the Resident On screen, 3 1 ➔ 1 (Application) ➔ Highlight the required software ➔

Setting the resume/suspend time (M7312/M7313)

☛

7 ➔ To display the Resident On screen, 3 1 ➔ 2 (Resume time) or 3 (Suspend time) ➔ Appropriate key for the required time

Storage info (M74)

You can display the number of Java™ applications currently stored in your phone and the size of free memory.

☛ 7 ➔ To display the Storage info screen, 4

Accessory (M8)

MP3 player (M81)

This feature allows you to create a Playlist to play MP3 files in the order you desire. You can add MP3 files saved in your phone to the Playlist (see “MP3
(M64)” on page 62) or change the order of the MP3 files within the Playlist.

☛ 8 1 ➔ SK1 to play ➔ After playing, SK2 to stop.
☛ To change the volume, Side keys.
☛ To play the previous/next file, ▲ or ▼.

2 When there are no MP3 files saved in the Playlist, the Playlist screen will be displayed in stead of the MP3 player screen.
2 When you use a wired headset, you can start or stop playing by pressing the button on it, and play the next file by pressing and holding it.

MP3 player Options menu

☛

8 1

No. MP3 player Options menu

1 Playlist Displays a list of MP3 files in the order in which they are played.

2 You can save up to 30 MP3 files in the Playlist depending on the size of each file.
2 The MP3 files that are deleted from MP3 of My data or erroneous MP3 files are displayed in gray and cannot

be played.

☛ to display the Playlist Options menu below, or SK1 to add an MP3 file.

1Add item Adds an MP3 file in your phone to the Playlist.

2 Move item Moves the highlighted MP3 file in the Playlist.

3 Delete item Deletes the highlighted MP3 file from the Playlist.

4 Delete all Deletes all the MP3 files from the Playlist.

5 View detail Displays the properties (file name, title, artist name and recording time) of the highlighted MP3 file.

Calculator (M82)

You can perform addition, subtraction, multiplication and division with the calculator. It also has a memory function.

☛ 8 2

2 The calculator can display a result of up to 9 digits. If a calculation results in a number exceeding the maximum, the screen displays error in the

calculation field.

Calculator Key Assignment

For calculator function, the keys are assigned different functions. The following shows the key assignment:

2 Using the % function, you can calculate (100 + x) % of a figure (e.g. 200 + 5% = 210) and (100 - x) % of a figure (e.g. 200 - 5% = 190).

Clock alarm (M83)

This feature enables you to switch the clock alarm function on/off and to set the time, repetition and alarm tone.

Turning the alarm on/off

☛ 8 3

Key Operation Key Operation

Addition (+) Subtraction (–)

▲ Multiplication (× ) ▼ Division (÷)

Equals to (=) SK2 Memory Store/Memory Addition

SK1 Memory Recall/Memory Cancel (Press twice) Percent (%)

Inversion (±) Exit calculator

Decimal Point (.) CLR Delete digit (if held, all clear)

Clock alarm setting

▼

▼

☛ When all settings are done, SK1 to save the setting.

2 The selected melody will be played when the alarm occurs if the ringer is turned on based on the current phone mode. If vibration is turned on, you

will be notified of the alarm by vibration.

2 Even if the phone has been switched off, the phone automatically switches itself on and sounds the alarm or vibrates at the specified time.
2 You can stop the alarm tone or vibration by pressing any key.

Scheduler (M84)

Scheduler enables you to enter reminders and appointments for particular time and date.

Adding a new event

☛ 8 4 ➔ Highlight the day ➔ to display the day’s schedule list screen (if any) ➔ SK1

☛ When all settings are done, SK1 to save the setting.

Scheduler setting

Event date/time Sets the day, month, year, time and am/pm (for 12 hour format) of the event.

Event end date/time Sets the day, month, year, time and am/pm (for 12 hour format) of the end of event.

Description Sets the event description (optional).

Repeat Selects repeat for One time only, Daily, Weekly or Monthly.

Reminder Turns on or off the reminder.

Reminder time Selects the time to set off the reminder prior to the event start time.

Reminder tone Associates a reminder tone with an event.

2 You can set the reminder tone only when the Reminder is turned on.

Private Sets the event as a private event.

☛ Place a check mark to set the event as a private event. To set the event as a public event, do not place a check

mark.

Viewing the scheduled events

☛

8 4 ➔ Highlight a day (SK1 to display the previous monthly/weekly view screen or SK2 to display the next monthly/weekly view screen)

☛ to display the day’s schedule list screen (To display the previous/next day’s schedule list screen, or ).
☛ to display the detail screen of the highlighted schedule.

Setting the reminder again

☛

When the scheduler reminder is set off, or and SK2 to select the time to remind again.

Scheduler Options menu

☛

8 4 ➔ Highlight the day ➔ to display the day’s schedule list screen (if any) ➔ Highlight the required scheduled event ➔

No. Scheduler Options menu

1 Add new Adds a new entry.

2Edit Edits the highlighted event.

3 Copy Copies the highlighted event.

4 Delete Deletes event(s). Press the appropriate keys for the event category (the currently selected event, all the public/

private events on the day, all the past public/private events, all the public/private events or all the events) to delete.

5 Go to date Displays the selected date.

6 Monthly calendar/

Weekly calendar

Switches the weekly view screen to the monthly view screen, or the monthly view screen to the weekly view screen.

2 You can select Sunday or Monday to start the week from “Set start day” on page 22.

7 View summary Displays the number of used and available entries.

8 View events Displays the events. Press the appropriate keys for the event category (Public only, Private only or All) to display.

2 You are required to key in the security code to display the private events or all events.

9IR send Sends the selected schedule through the IR port to other devices or a cellphone.

2 The IR send function is not available during a call.

▼

▼

▼

▼

Adding a new ToDo task

☛

8 5 ➔ Highlight the list ➔ ➔ SK1

☛ When all settings are done, SK1 to save the setting.

When a ToDo task is completed

☛

8 5 ➔ Highlight the list ➔ ➔ Highlight the required ToDo task ➔ ➔ 1 and 1, or SK2 to save the task as completed.

Viewing ToDo task details

☛

8 5 ➔ Highlight the list ➔ ➔ Highlight the required ToDo task ➔ ➔ To view the details of the previous or next ToDo task in the list,

or

☛ To edit the currently displayed task, SK1

ToDo Options menu

☛

To display the ToDo Options menu, 8 5 ➔ Highlight the list ➔ ➔ Highlight the required ToDo task ➔

☛ To display the ToDo detail Options menu, 8 5 ➔ Highlight the list ➔ ➔ Highlight the required ToDo task ➔ ➔

Column L shows the ToDo options menu, and column D shows the ToDo detail Options menu.

ToDo list setting

Start date Sets the day, month and year to start the ToDo task.

Due date Sets the date to end the ToDo task. Key in the date or press the appropriate key for the date.

2 If you select to key in the date yourself, input the day, month and year of the date to end the ToDo task, then SK1.

Description Sets the ToDo task description (e.g. Pay the rent).

Category Sets the category (Business, Personal or Other).

Priority Sets the priority (Normal, Low or High).

Private Sets the ToDo task as private.

L D ToDo Options menu

▼

▼

2 Depending on the conditions, some options may be displayed in gray and not be available.

Notepad (M86)

Notepad function allows you to record and store a note as a text file.

Creating a new memo (M861)

☛

8 6 1 ➔ Key in text ➔ to save the entry as a text file. The first few words are displayed on the text list screen.

Displaying a memo (M862)

☛

8 6 2 ➔ Highlight a file ➔ SK1 to preview, or to edit

Notepad Options menu

☛

8 6 2 ➔ Highlight a file ➔

4 –Display

filter

Sets the type(s) of ToDo tasks to be displayed by selecting the desired filter option (None, Incomplete or Completed).

5 – Sort list Displays a list of ToDo tasks rearranged according to the selected sort key (Due date, Category, Priority, or Status).
6 –View

summary

Displays the number of Incomplete and Completed tasks and how many more tasks can be created.

7 5 IR send Sends the selected ToDo task through IR port to other devices or a cellphone.

2 The IR send function is not available during a call.

No. Notepad Options menu

1Edit item Changes the protection settings of the selected file.

Rename item: Edits the file/folder name of the selected file/folder.
Set protection: Sets the protection settings of the selected folder or file on/off.

2 Use item Add desktop icon: Creates a desktop icon of the selected file on the standby screen.

L D ToDo Options menu (Continued)

2 Depending on the conditions, some options may be displayed in gray and not be available.

Voice memo (M87)

Voice memo function allows you to record up to 60 seconds of sound/voice, using your phone’s microphone.

Recording/playing voice memo or setting speaker

☛

8 7

8Move Moves the selected note or all the notes in the current folder to a folder.
9 Create folder Creates a new folder under the current folder.
0 Storage detail Displays the current storage information of your phone memory.

View detail Displays the detail of the selected file.

2 You can also display the details on the highlighted folder or file by pressing without displaying the Options menu.

# Options Sorting order: Sorts the files by date or alphabetically.

Info column: Sets whether to display the column on the list screen, and the information to be shown there.

None: No column showing
Size: Approximate size of the file
Type: File type

2 You can also change the information on the column by pressing # without displaying the Options menu.

Flat view: Displays the list of all the stored files regardless of the folder hierarchy.
Save options: Saves the current option settings.
Reset options: Resets the option settings.

No. Voice memo setting

1Record Records a voice memo.

☛ SK1 to start recording.

No. Notepad Options menu (Continued)

Currency (M88)

Currency function allows you to convert an amount of money in one currency to another.

Converting currency

☛

8 8

2 If you have made a mistake in entering the exchange rate or amount, CLR to delete individual number or SK2 to cancel the entry and return to

the previous screen, and then start again.

Resetting the currencies

☛

8 8 and SK1

External connection (M89)

External connection allows you to communicate with other devices (PC, PDA, headset, etc.)

2 You cannot use the Infrared and Bluetooth functions at the same time.

Bluetooth (M891)

Bluetooth function allows you to use your phone as a modem and to talk by using a Bluetooth headset.

☛ 8 9 1

Currency setting

From Sets the source currency code.

To Sets the destination currency code.

Exchange rate Sets the exchange rate.

☛ If you wish to change the exchange rate, CLR to delete the displayed exchange rate and key in the required number

(for decimal point, SK1) ➔

Amount Sets the amount of money you wish to convert (for decimal point, SK1).

Synchronization (M80)

Synchronization function allows you to synchronize data between your phone and your PC. When your phone is connected to your PC via a USB cable
(option), you can synchronize phonebook, scheduler or ToDo list data.

2 Data should comply with vCard 2.1/vCalendar 1.0 specification
2 You cannot synchronize the phonebook data stored in the SIM card.

☛ Connect your phone with your PC via a USB cable ➔ Activate the software on PC side and prepare for synchronization (for details, refer to the

manuals of the software)

☛ 8 0 ➔ Select the data type (Phonebook, Scheduler or ToDo list) ➔ SK1 or 1 to start synchronization

Bluetooth (M891)

Bluetooth function allows you to communicate with the external devices (PC, PDA, headset, hands-free kit, etc.).
This function provides the following service:

• Dial-up service - You can use your phone as a modem.

• Headset/hands-free service - You can make/receive a call using a Bluetooth headset or hands-free kit.

2 When using Bluetooth devices, always refer to their operation manual.
2 Depending on the connection status, a Bluetooth device may not function correctly. In such a case, retry operation from the device side, or switch

your phone off and on.

2 There may be Bluetooth devices that cannot be connected to your phone.

Using Bluetooth connection

2 To use the Bluetooth function, you must perform the Bluetooth settings on your external device beforehand. For details, refer to the operation manual

of the device.

2 You cannot use the Bluetooth and Infrared functions at the same time.

, While using the Bluetooth device, the following icons will be displayed in the status bar area of your phone.

Pairing a Bluetooth device and your phone

☛

8 9 1 ➔ 2 ➔ 1 to be searched by other Bluetooth devices or 2 to search other Bluetooth devices

☛ If the device is found, the list of found Bluetooth devices will be displayed
☛ Highlight the device from the list➔ ➔ Input passcode of the found Bluetooth device

2 When pairing, you will be asked to enter a passcode specified by the Bluetooth device to your phone and the device. If no passcode is specified

by the device, enter the same arbitrary number to your phone and the device. A passcode is a number from 4 to 16 digits.

Bluetooth setting

Indicates that Bluetooth device is set to on. Indicates that Bluetooth device is in operation.

2 Depending on the conditions, some options may be displayed in gray and not be available.

Device list Option menu

☛

8 9 1 ➔ 3

Device list icons

2Pair new

device

Registers the external Bluetooth devices.

1 Wait for connect Standby your phone to wait for other devices to search for it.

2 Other Bluetooth devices can only detect your phone while your phone is displaying

Wait for connect screen.

2 Search device Searches for the nearby active Bluetooth devices.

3 Device list Displays and edits the list of paired devices.

4 My phone Displays the terminal information of your phone.

☛ to display the Options menu

Rename: Edits the terminal name of your phone.

2 You cannot edit the information during Bluetooth communication.

5 Active device Displays the information on the device in connection.

6 Disconnect Ends the Bluetooth connection in progress.

No. Device list Option menu

1 Rename Edits the name of the highlighted device.

2 Protect/Un-protect Protects or unprotects the highlighted device.

3 Delete device Deletes the highlighted device.

4 Delete all devices Deletes all the devices listed.

No. Bluetooth setting

Using your phone as Bluetooth modem

2 For details of dial-up connection settings, consult your Internet service provider.

☛ Pair the Bluetooth device and your phone beforehand (see “Pairing a Bluetooth device and your phone” on page 76)
☛ 8 9 1 ➔ 1 to activate Bluetooth function ➔ Perform dial-up connection by your PC
☛ To end the dial-up connection, disconnect from the PC application

2 You can also end the dial-up connection by pressing 8 9 1 6

Connecting Bluetooth headset/hands-free kit

2

When connecting a wired headset and Bluetooth headset at the same time, the wired headset will not work.

2 For some Bluetooth devices, the voice recall function may be activated when a paired headset/hands-free kit is turned on (see “Voice recall” on

page 8).

☛ Pair the Bluetooth device and your phone beforehand (see “Pairing a Bluetooth device and your phone” on page 76)
☛ 8 9 1 ➔ 3 ➔ Highlight the headset/hands-free kit in the list ➔ SK1

Using Bluetooth headset/hands-free kit

☛

To answer the incoming call, press the button on the headset/hands-free kit

☛ To switch the headset/hands-free kit call to your handset call during a call, 9

2 You cannot deactivate Bluetooth during a call.

☛ To end the call, or end from the headset/hands-free kit

IR Data Exchange

Your phone is equipped with an InfraRed (IR) data port which enables you to send and receive picture/sound/MP3/video/ToDo list/scheduler/phonebook/
note data with cellphones or other devices equipped with IR ports.

, Do not aim or direct the IR data port towards your or other people’s eyes when using IR data exchange.
, Do not aim or direct the IR data port towards another IR device as this may cause the device to malfunction.

2 Depending on the other party’s cellphone or device, the data may not be received correctly.
2 You cannot use the Infrared and Bluetooth functions at the same time.
2 While sending or receiving data through IR or using your phone as an IR modem, your phone is automatically placed out of service, so phone call,

message and WAP access are disabled.

Positioning of the phones

, Open both sending and receiving phones vertically and place them as

their IR ports face each other with less than 20cm of interval.

2 Do not place anything between IR ports.
2 The angle made of two IR ports must be within 30°.
2 Do not move the phones until the data exchange is complete.
2 The phones may not communicate successfully if they are placed under direct

sunlight or fluorescent light, or close to other infrared devices.

IR send

You can send picture/sound/MP3/video/ToDo list/scheduler/phonebook/note data as a file through the IR port.

2 This function is not available during a call.
2 Before starting to send data, the other party must be ready to receive data.

15° or less

20cm or less

Video/Sound/Picture/MP3 file (M6...)

☛

6 1 for Videos, 6 2 for Sounds, 6 3 for Pictures or 6 4 for MP3 ➔ Highlight a folder ➔ ➔ Highlight a file.

☛ 2 3 for Videos/Pictures, 2 4 for Sounds or 2 2 for MP3 ➔ The file will be sent through the IR port (see “My data (M6)” on

page 59 for details).

Schedule entry (M84...)

☛

8 4 ➔ Highlight a date ➔ ➔ Highlight a schedule entry ➔ ➔ 9 ➔ The schedule entry will be sent through the IR port.

ToDo entry (M85...)

☛

8 5 ➔ Highlight Public, Private or All ➔ ➔ Highlight a ToDo entry ➔ 7 ➔ The ToDo entry will be sent through the IR port.

Note (M862...)

☛

8 6 2 ➔ Highlight a note ➔ 2 and 2 ➔ The note entry will be sent through the IR port.

IR receive (M8921)

You can standby your phone to receive data (picture/sound/MP3/video/ToDo list/scheduler/phonebook/note) from other devices or a phone of the same model.

Receiving data through IR (M8921)

☛ 8 9 2 1 ➔ Start sending data from the other end.

2 Once the transmission completes, your phone automatically judges the type of received data and stores the data accordingly.
2 This function is not available during a call.
2 If your phone does not have enough space to store the received data, a message will be displayed indicating lack of space. In such a case, delete

unnecessary data and try the data exchange again.

2 Received picture/video/sound files are stored in the Download folder of My data (see “My data (M6)” on page 59).

IR modem (M8922)

You can use your phone as a modem for a PC via the IR port to establish a dial-up connection to an Internet service provider.

Activating the IR port for modem use (M8922)

Index

A

AC adapter 3
Accepting an incoming call 7
Accessory 67
ADN 45
Alarm volume 23
Alert message 29, 43
ALS 21
Animation 60
Any key answer 21
AoC 12
Auto answer 23
Auto redial 14

B

Bar calls 26
Basic calls & phone use 6
Battery charging 3
Battery level icons viii, 4
Battery pack 1
Blacklist 12
Bluetooth 76
Bookmark 43

C

Recording a video 56

Taking a picture 54
Car mode 22
CB 39
CLI 6, 50
Clock 22
Clock alarm 68
Clock selection 24
Clock/Event display 24
Colour style 24
Connection profile 26
Contrast 24
Correcting mistakes 6
CSD 40
Currency 74

D

Date 22
Date format 22
Desktop icons 19
Dialled calls list 12
Download 40

E

Earphone setting 23

F

Fast dialling 8
FDN 26, 46
Flicker control 55, 58
Fold answer 21
Frame 61
Frequency band 15
Function key LED 25

G

General care i
GPRS 40
Greetings 24
Groups 48

H

Hands-free kit 76
Headset 22, 76
Highlight mode 33, 38
Holding a call 9
Homepage 40

I

Icons viii, 29, 37, 76, 77
Inbox 28

J

Java™ 65
JPEG 53

K

Key allocations 18
Key tone 23
Keypad shortcuts vii

L

Language 22
Last call duration 11
Last number redial 7
LCD v
LED 22
Line ID 14
Logging on to WAP site 42
Low battery alarm 4

M

Main menu x
Main menu style 24
Main-LCD 24
Making basic calls 6
Meeting mode 22

Multi-party calls 10
Mute 9
My data 59

MP3 62
Pictures 60
Sounds 59
Videos 59

N

Network selection 15
Normal mode 22
Normal text (ABC) input 17
Notepad 72
Number type 51
Numeric input 17

O

One-touch dial 8
Option mode 33
Origin number 51
Own phone number display 8

P

Parts and functions vi
Phone lock 26
Phone modes 22
Phonebook 45
PIM 26

R

Reading a message 29
Received calls list 12
Receiving an incoming call 6
Recording a call 11
Redial blacklist 12
Rejecting an incoming call 7
Reset settings 27
Ring silencer 21
Ringer 23
Ringer volume 23
Roaming 15

S

Scheduler 69
Scratchpad number 11
SDN 46
Security 25
Security code 25
Service tone 23
Setting your connection
profile and homepage 40
Settings 21
Shortcuts selection x
Side key lock 21
SIM card 1
SIM card insertion 1

Starting a call 6
Start-up 4
STD 6
Switching the phone off 5
Switching the phone on 4
Synchronization 75

T

Text entry 16

Mode change 16
Time 22
Time format 22
Timezone 22
ToDo list 70
Total calls duration 11
T9 English text input 16

U

Unsuccessful calls 7
User’s manual conventions iv

V

Vibrator 23
Video 53

Recording a video 56
View mode 34
Voice mail 52
Voice memo 73

Z

Zoom 55, 58

0-9

2nd-LCD 24
3GPP 53
4 way navigation key vi