NAD M55 User Manual

M55

Digital Disc Player

ENGLISH

FRANÇAISDEUTSCH

Owner’s Manual Manuel d’Installation Bedienungsanleitung Gebruikershandleiding

NEDERLANDS

ESPAÑOLITALIANO

PORTUGUÊS

SVENSKA

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

Introduction

IMPORTANT SAFETY INSTRUCTIONS

• Save these instructions for later use.

• Follow all warnings and instructions marked on the audio equipment.

1 Read instructions - All the safety and operating instructions should be read before the product is operated.

2 Retain instructions - The safety and operating instructions should be retained for future reference.

3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.

4 Follow Instructions - All operating and use instructions should be followed.

5 Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments - Do not use attachments not recommended by the product manufacturer as they may cause

hazards.

7 Water and Moisture - Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink,

or laundry tub; in a wet basement; or near a swimming pool; and the like.

8 Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9 A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces

may cause the product and cart combination to overturn.

10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of

the product and to protect it from overheating, and these openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should

not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources - This product should be operated only from the type of power source indicated on the marking

label. If you are not sure of the type of power supply to your home, consult your product dealer or local power

company.

• Main Power Disconnect; When the power switch is in the Off position, the amplifier is not completely

disconnected from the main power. The primary method of isolating the amplifier from the mains supply is to

disconnect the mains plug. Ensure that the mains plug remains accessible at all times. When installing the

product, ensure that the plug is easily accessible.

• Non-use Period; Unplug the AC power cord from the AC outlet if the unit will not be used for a long period

of time such as several months or more.

• CLASS 1 Products; The M55 shall be connected to a MAINS socket outlet with a protective earthing connection.

12 Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the product.

13 Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper

grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements

for the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER

• This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected

to the grounding system of the building, as close to the point of cable entry as practical.

14 Lightning - For added protection for this product during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This

will prevent damage to the product due to lightning and power-line surges.

15 Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with

them might be fatal.

16 Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can

result in a risk of fire or electric shock.

17 Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch

dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind

on the product.

WARNING

18 Transportation - Transport the M55 in the shipping containers supplied. Do not transport the M55 using one

shipping container; to do so may result in damage to either the amplifier or personnel.

IMPORTANT SAFETY INSTRUCTIONS

19 Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the

following conditions:

a) When the power-supply cord or plug is damaged.

b) If liquid has been spilled, or objects have fallen into the product.

c) If the product has been exposed to rain or water.

d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by

the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive

work by a qualified technician to restore the product to its normal operation.

e) If the product has been dropped or damaged in any way.

f) when the product exhibits a distinct change in performance-this indicates a need for service.

20 Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by

the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or

other hazards.

21 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

22 Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE LIGHTNING

FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE

PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF

SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF

IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE

APPLIANCE

CAUTION

Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user’s authority

to operate this equipment.

CAUTION REGARDING PLACEMENT

To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal

to, or greater than, shown below.

Left and Right Panels : 10 cm

Rear Panel : 10 cm

Top Panel : 50 cm

Introduction

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

IMPORTANT INFORMATION FOR UK CUSTOMERS

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable

is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. If, nonetheless,

the mains plug is cut off, REMOVE THE FUSE and dispose of the PLUG immediately, to avoid possible shock hazard by inadvertent

connection to the mains supply. If this product is not provided with a mains plug, or one has to be fitted, then follow the instructions

given below:

IMPORTANT

DO NOT make any connection to the larger terminal which is marked with the letter ‘E’ or by the safety

earth symbol or coloured GREEN or GREEN AND YELLOW.

The wires in the mains lead on this product are coloured in accordance with the following code:

BLUE - NEUTRAL

BROWN - LIVE

As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The BLUE wire must be connected to the terminal marked with the letter ‘N’ or coloured BLACK.

The BROWN wire must be connected to the terminal marked with the letter ‘L’ or coloured RED

When replacing the fuse, only a correctly rated and approved type should be used, and be sure

to re-fit the fuse cover.

IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN

This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC, and

73/23/EEC.

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection

point for the recycling of electrical and electronic equipment. The symbol on the product, user's manual and packaging, point this out.

The materials can be reused in accordance with their markings. Through re-use, recycling of raw materials, or other forms of recycling

of old products, you are making an important contribution to the protection of our environment. Your local administrative office can

advise you of the responsible waste disposal point.

ITALIANO

PORTUGUÊS

SVENSKA

ENGLISH FRANÇAIS

DEUTSCH

Introduction

TABLE OF CONTENTS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE

CAUTION

THIS DVD PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS

OWNER’S MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE,

CONTACT AN AUTHORIZED SERVICE LOCATION.

USE OF CONTROLS, ADJUSTMENTS TO MODIFY PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION

EXISTS WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM.

THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS,

SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

NOTE

M55 is not an auto voltage DVD player. Connect only to the prescribed AC outlet, i.e., 120V 60Hz or 230V 50Hz.

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

TABLE OF CONTENTS

RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT)

your new DVD player are located on the back of the DVD player cabinet. For your future convenience, we suggest

that you record these numbers here:

Model No. :________________________Serial No. :_________________

The model and serial number of

INTRODUCTION

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

IDENTIFICATION OF CONTROLS

Front Panel/Display window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8

Preparing The Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operation Of The M55 With The Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . .11

OPERATION

Operation of the M55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Special Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14

Automatic Power Off Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Stopping Play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Resume Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Still Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Frame Advance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Skipping chapters and tracks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Scanning at High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Playing in Slow-Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

OSD Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Display/Titles/Menus/Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Viewing From Another Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Storing Markers in Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Zoom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Random Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Playback Audio with CD, SACD, VCD, and DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SETUP

Connecting to Surround Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-23

SACD/DVD-A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Dolby Digital Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Dolby Pro Logic Surround Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2-Channel Digital Stereo Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DTS Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Connecting to an Analogue Stereo System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Connecting to a TV Directly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Initial Setup Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-29

Selecting Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Selecting Video Aspect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Selecting Scan Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Selecting Signal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting Gamma Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting Black Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting Brightness Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting Contrast Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting Saturation Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting Video Adjustment Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Selecting Digital and Audio Output and Other Settings . . . . . . . . . . . . . . . . . . . . . . . . 31

REFERENCE

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Disc Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Table of Languages and Their Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Video Output Scan Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

High resolution DVD-audio stereo 192kHz 24-bit discs. . . . . . . . . . . . . . . . . . . . . . . . . 37

Introduction

TABLE OF CONTENTS

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ABOUT THIS OWNER’S MANUAL

This owner’s manual explains the basic instructions of this M55. Some DVD/DVD-A/SACD/VCD/CD media have functions that may not be explained in this owner’s manual. Therefore, some instructions may differ from the M55 owner’s manual, and there may be extra instructions. In this case, follow the instructions displayed on the media package or displayed on the OSD during operation.

NOTES

• Refer to the owner’s manual of your audio equipment as well. When you connect the M55 to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. The output sound of the M55 has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound. Turn off the receiver before you connect or disconnect the M55’s power cord. If you leave the receiver power on, the speakers may be damaged.

• When playing high bit rate recordings, like DVD-Audio or SACD, some of the video menus may become unresponsive. Under these conditions all of the M55's resources are being used to decode the audio data.

• For gapless playback of musical works that include individual tracks but no silent gaps between songs or movements, the disc should be played from the beginning without interruption. Skipping tracks or using the Program Mode will introduce gaps.

ITALIANO

PORTUGUÊS

SVENSKA

NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited

ENGLISH FRANÇAIS

Identification of Controls

FRONT PANEL

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

1-2Power button and On/Standby indicator 3 Display window 4 Select/Enter/Navigation buttons 5 stop button 6 open/close button

DISPLAY WINDOW

7 DVD/CD tray 8 play/pause button 9 menu button

PORTUGUÊS

SVENSKA

1 DVD-Audio and Dolby Digital multi-channel output indicator 2CD, VCD and SVCD indicator 3 PBC indicator for VCD and SVCD 4HD(Hi Definition) indicator 5 HDMI indicator 6 P. SCAN (Progressive Scan) indicator 7 MP3 indicator 8 WMA indicator 9 JPEG Indicator 10 ANGLE Indicator 11 TITLE, TRK, and CHAP indicators 12 DTS indicator

13 SACD (2-channel or multi-channel) indicator 14 PROGram indicator 15 HDCD indicator 16 Play and Pause indicators 17 RANDOM play indicator 17 Chapter number display 18 Repeat, repeat ALL, repeat A-B indicator 19 Total playing time display 20 Title number display 21 Track number display

Identification of Controls

REAR PANEL (NORTH AMERICAN VERSION)

ENGLISH

1 IR IN Jack 2 DIGITAL OUT COAXIAL Jack 3 DIGITAL OUT OPTICAL jack 4 MIXED AUDIO OUT (L & R) Jacks 5 5.1 CH AUDIO OUT FRONT L & R Jacks 6 5.1 CH AUDIO OUT CENTER and SUBW (Subwoofer) Jacks 7 5.1 CH AUDIO OUT SURR (Surround Sound) L & R Jacks 8 S-VIDEO & Composite VIDEO OUT Jacks (480i/576i video

resolutions)

9 COMPONENT VIDEO OUT Jacks (480i/576i or 480p/576p, video

resolutions)

NOTES

Connect the optical digital cable (not supplied) firmly so that the configurations of both the cable and the connector match. The +12V TRIGGER IN jack is a 3.5mm monotype miniature phone jack with the centre pin the 12V signal-sense. We recommend that you use a good quality cable with shield when attaching the 3.5mm monotype plug so as to prevent false triggering of the amplifier due to electromagnetic interference from nearby electronic equipment. The +12V-IN TRIGGER allows you to have an external 12V signal to turn ON the NAD M55 from standby. This 12V signal must be a continuous 12V signal in order to keep the M55 in the ON state. Once you remove the 12V signal the M55 will return to standby. Check the specifications of the trigger input terminal the other components to ensure these are compatible with the M55. All 12V-TRIGGER inputs and outputs on other NAD components with a 12V-TRIGGER feature are fully compatible with the NAD M55’s 12V-TRIGGER IN. Before making any connections to any 12V-TRIGGER IN make sure all components are disconnected from the AC mains. If in doubt over the connections, installation and/or operation of the 12V-TRIGGER IN connection, consult your NAD dealer or sales representative. Failure to observe the above may result in damage to the NAD M55 and/or any ancillary components attached to it. The IR IN jack is connected to the output of an IR (infrared) repeater (Xantech or similar), or the IR output of another component to allow control of the M55 from a remote location. Ask your dealer or custom installer for further details

10 HDMI OUT Jack (480p or 576p video resolutions) 11 VGA OUT Jack (480p/576p, 720p, and 1080i video resolutions) 12 AUTO TRIGGER ON/OFF Switch 13 +12V TRIGGER IN jack 14 Power cord socket 15 POWER ON/OFF 16 RS 232 In/Out Jack

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

ENGLISH FRANÇAIS

Identification of Controls

REAR PANEL (EUROPEAN VERSION)

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

resolutions)

9 COMPONENT VIDEO OUT Jacks (480i/576i and 480p/576p, video

resolutions)

NOTES

10 HDMI OUT Jack (480p/576p, video resolutions) 11 VGA OUT Jack (480p/576p, 720p, and 1080i video resolutions) 12 AUTO TRIGGER ON/OFF Switch 13 +12V TRIGGER IN jack 14 SCART/RGB OUT Jack (480i and 576i, video resolutions) 15 Power cord socket 16 POWER ON/OFF 17 RS 232 In/Out Jack

PORTUGUÊS

SVENSKA

Identification of Controls

PREPARING THE REMOTE CONTROL

Insert the batteries into the remote control so you can use it to operate the M55.

1 Open the battery cover 2 Insert two batteries (AA size) 3 Make sure to match the + and - on the batteries to the marks inside the battery compartment. 4 Close the cover

NOTES ON BATTERIES

Improper use of batteries may cause battery leakage and corrosion.

• To operate the remote control correctly, follow the instructions.

• Do not insert the batteries into the remote control in the wrong direction.

• Do not charge, heat, open or short-circuit the batteries.

• Do not throw the batteries into fire.

• Do not leave dead or exhausted batteries in the remote control.

• Do not use different types of batteries together, or mix old and new batteries.

• If you do not use the remote control for a long period of time, remove the batteries to avoid possible damage from battery corrosion.

• If the remote control does not function correctly or if the operating range becomes reduced, replace all batteries with new ones.

• If battery leakage occurs, wipe the battery liquid from the battery compartment, then insert new batteries.

• The batteries should last about one year with normal use.

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

OPERATION OF THE M55 WITH THE REMOTE CONTROL

This section shows you how to use the remote control. Point the remote control at the remote control sensor and press the buttons.

30° 30° 23 ft (7m)

Distance: About 23 ft (7 m) from the front of the remote sensor Angle: About 30 degrees in each direction of the front of the remote sensor

NOTES ON THE REMOTE CONTROL

• Do not expose the remote sensor of the M55 to a strong light source such as direct sunlight or illumination. If you do so, you may not be able to operate the M55 with the remote control.

• Point the remote control at the remote sensor on the M55.

• Do not drop or give the remote control a shock.

• Do not leave the remote control near an extremely hot or humid place.

• Do not spill water or put anything wet on the remote control.

• Do not disassemble the remote control.

ITALIANO

PORTUGUÊS

SVENSKA

Identification of Controls

REMOTE CONTROL

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

9 10

12 13

ITALIANO

PORTUGUÊS

SVENSKA

1 POWER ON, POWER OFF 2 SETUP 3 Transport control keys OPEN/CLOSE, STOP, PAUSE, STEP, PLAY, SKIP,

SCAN, SLOW

4 ENTER and navigation buttons 5 RETURN 6 TITLE, MENU 7 DISPLAY 8 PROGRAM, CLEAR 9 REPEAT

10 REPEAT A-B 11 AUDIO 12 SUBTITLE 13 ANGLE 14 Numerical buttons 15 MARKER, SEARCH 16 ZOOM 17 RANDOM 18 RESOLUTION

Identification of Controls

1 The power buttons labelled ON and OFF will toggle the M55 from standby to the on-position, only if

the POWER rocker switch on the left rear of the M55 is in the ON position.

2 The SETUP button is used in conjunction with the television monitor’s On Screen Display (OSD)

connected to the M55, (see the section on ‘Initial Set-up Settings’) to edit the DVD’s OSD.

3 There are ten transport control buttons that allows one to directly control the DVD/VCD/CD media.

These buttons handle the basic operations of; Open/Close of the media tray, Stop , Pause , Skip forward and back , Play , Scan tracks , and Slow scan tracks .

4 The navigation buttons in conjunction with the ENTER button allows one to navigate the

OSD, title and menu screens.

5 The RTN button is used for returning to Menus of various VCD and SVCD disc media with PBC (Play

Back Control). Please note that PBC must be set to ON in the Others OSD Setup Menu in order for the RTN option to function.

6 The TITLE and MENU buttons are used to display the Title and Menus of the DVD-Video, DVD-Audio,

and MP3/WMA/JPEG CD media when available. The MENU button will allow you to select between CD and SACD layers of SACD media as well.

7 The DISP (Display) button will show multiple navigation OSD for advanced DVD-Video, VCD, and

CD/DVD JPEG media options when the M55 is in play or pause mode. The Display function is not available for DVD-Audio

8 The PROGRAM and CLEAR buttons are used for programming the files on CD/DVDs with

MP3/WMA/JPEG files as well as CD/SACD media.

9 The REPEAT button when pressed once, repeats MP3/WMA/JPEG/CD/SACD track or a DVD-Video

and DVD-Audio chapter. If the button is pressed twice the entire MP3/WMA/JPEG/CD/SACD folder is repeated or the DVD-Audio/Video Title is repeated.

10 The REPEAT A-B button is used to repeat a specific start to stop section of an audio CD or DVD/VCD.

During play mode of the media, press the button once to store the start point of the M55 in memory. When pressed a second time the stop point of the media is stored. The M55 will play the selected section(s) until REPEAT A-B button is pressed a third time.

11 The AUDIO button will allow one to switch the audio language of the DVD media only if the DVD

media supports the AUDIO button feature.

12 The SUBTITLE button will allow one to switch on or off the various types of subtitles for the DVD

media being viewed, only if the DVD media supports the SUBTITLE button feature.

13 The ANGLE button will allow one to select various viewing angles of each movie scene only if the DVD

media supports this feature.

14 The number buttons are used for inputting numeric values when navigating the menu, title, and

display OSDs or when directly selecting media tracks.

15 The MARKER and SEARCH buttons allows one to set up to 9 bookmarks on a DVD and VCD for

quick reference. After each marker is stored one then presses the SEARCH then navigation buttons to play the bookmark.

16 The ZOOM button allows one to expand the viewed image from 1 1/2, 2, to 3 times. To clear the

zoom, press the ZOOM button repeatedly until the Zoom off OSD is displayed.

17 The RANDOM button allows one to randomly play audio MP3/WMA/JPEG/CD/SACD media. In

conjunction with the REPEAT buttons the media would randomly play all tracks. This feature is not available on most DVD-Video and DVD-Audio discs.

18 TThe RESOLUTION button allows one to select the HDCP video resolutions from the Component,

HDMI, and VGA output.

NOTE:

Not all resolutions are available on all outputs. See chart on page 37

// /

REMOTE CONTROL

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

Operation

OPERATION OF THE M55

INTRODUCTION

When you want to play back DVD-Video discs and DVD-Audio or audio CDs, turn on your A/V audio system and the TV and then select the video input source connected to the DVD player.

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

Set the playback picture size according to the aspect ratio of the connected TV in the setup OSD menus.

Switch ON the POWER rocker switch, then the front panel Standby button.. The M55-power indicator becomes blue. Press OPEN/CLOSE. The disc tray opens.

• You can open the disc tray by pressing this button even if the DVD player is in standby mode. The power indicator will turn from amber to blue.

Place a disc on the disc tray with the playback side down.

• There are two different disc sizes. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the M55 to malfunction.

Press PLAY. The disc tray is automatically closed and playback begins.

• If the disc is placed in upside down (and it is a single sided disc), NO DISC will appear on the M55’s display and ‘NO DISC’ appears on the TV screen.

• If you insert an audio CD, the total tracks and time will appear.

• After playing back all of the chapters in the title, M55 automatically stops and returns to the menu screen.

Press the navigation keys then and press ENTER, or press the numeric button(s), to select the desired item. Play of the selected item now begins.

• For further information, also refer to the jacket or case of the disc you are playing.

AFTER OPERATION

When the unit is not in use, remove the disc and press the OFF button on the remote to switch the M55 to standby. If the M55 is left unattended for any length of time such as during a vacation, then switch off the M55 by depressing the black rocker switch marked POWER ON/OFF found on the rear of the M55.

NOTES

• Do not move the DVD player during playback. Doing so may damage the disc and the M55.

• Use the OPEN/CLOSE button on the M55 or on the remote control to open and close the disc tray.

• Do not push or pull the disc tray while it is moving. Doing so may cause the M55 to malfunction.

• Do not push up the disc tray or put any objects other than discs on the disc tray. Doing so may cause the M55 to malfunction.

• Keep your fingers well clear of the disc tray as it is closing. Be especially careful with children’s fingers around the closing disc tray, as there is a risk of personal injury.

• Depending on the DVD disc, some operations may be different or restricted. Refer to the jacket or case of the disc you are playing.

PORTUGUÊS

SVENSKA

+ 26 hidden pages

NAD M55 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual