Motorola HT820 User Manual
USE THE HT820
)
)
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
Start Here > > >
HT820
Bluetooth®
Stereo Headphones
You can use your HT820 headphones
simultaneously with a Bluetooth A2DP
enabled audio device and your Bluetooth cell
phones!
Listen to music, hear a beep, and transfer to
take the call on the headphones. Hang up the
call with a push of a button and your music
automically continues playing.
Any Bluetooth
Enabled Audio
Device*
HT820
o
Bluetooth
Enabled
Ready to make it work?
- Charge your Headphones for 2 Hours (CHARGE)
- Pair headphones & audio device (PAIR)
-
Pair phone & headphones (back side of this guide
- Listen to music and take calls!
*The Bluetooth Enabled Audio Device must be A2DP compatible
Phone
CHARGE
1
Before using your HT820 for the first time,
charge the headphones for 2 hours:
Plug the Motorola charger into the
1
headphones. The indicator light turns on
when the battery is charging. When the
headphones' battery is fully charged, the
indicator light turns off.
Disconnect the charger.
2
Note: Headphones do not function while charging.
You can also use a Motorola Original™
Vehicle Power Adapter to charge your
headphones while in your vehicle.
A fully charged battery provides
approximately: 14 hrs of music listening, 17
hrs of talk time, or 500 hrs of standby time.
Your Headphones' Battery
Charger
Insert Charger
Here
Music Button
Indicator
(Right Side)
Light
2
Before you can use your headphones with a
Bluetooth enabled product, you must pair it
with that product. To pair:
Make sure your headphones are turned off
1
(see Turning On and Off ) and press and
hold the left side Callmbutton for 6
seconds until the indicator light turns on and
remains steadily lit.
Call Button with
Indicator Light
(Left Side)
Next, put your Bluetooth Enabled audio
2
device in pairing mode so the devices can
"talk" to each other.
For details about putting Bluetooth
Enabled devices in pairing mode, refer to
the device's User's Guide for directions.
Note: To pair the headphones with your phone, see "Pair
with your Phone," on the reverse side of this guide.
PAIR
3
Your headphones are successfully paired
with a device and ready to use when the
blue indicator lights changes from steadily lit,
flashes rapidly, and then slowly flashes.
To confirm they are operating properly:
1
2
Your Headphones & Audio Device
Place the headphones on your head. See
Wear the Headphones in this guide.
Start playing music on the audio device. If
your headphones are successfully paired,
you will hear music in the headphones.
Note: You may need to wait several seconds before
hearing music in the headphones while the devices
connect.
TEST AND USE
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-800-331-6456 (United States)
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
1-800-461-4575 (Canada)
See Music Controls for information about
using the HT820 volume and playback
controls.
After successfully pairing, you do not need to
repeat these initial setup steps each time you
use the headphones. Just power on both
devices and they automatically connect.
TURN ON AND OFF
To turn your headphones on, press and hold
the left side Call mbutton until the indicator
light flashes 3 times (about 3 seconds).
release the button.
To turn your headphones off, press and hold
the left side Call mbutton until the indicator
light flashes
seconds)
rapidly and then turns off
.
Then,
(about 3
6809496A47-B
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The Bluetooth trademarks are owned
by their proprietor and used by Motorola, Inc. under license. All
other product or service names are the property of their
respective owners. © Motorola, Inc. 2006.
CONNECT SIMULTANEOUSLY
Simultaneous connect your headphones
with a music device AND your phone!
Pair the headphones to the music device
(PAIR). Then pair the headset with your
phone (backside of guide). Power your
headphones off and then back on. After a
few moments it will connect with both the
music device and phone.
To conserve battery power, turn off the
headphones when you will not be using it.
WEAR THE HEADPHONES
Your headphones are designed to be worn
comfortably with the neck band positioned
behind your head.
The microphone is located in the right ear-piece.
Digital Signal processing is used for clear pickup of your voice during voice calls.
Any Bluetooth
Enabled Audio
Device*
o
Bluetooth
Enabled
Phone
Note: The remote control functions only
work when the headphones are directly
connected to source device. via Bluetooth.
Loading...